Search Documents

By Steven Hart

In September 2009, Newmont began the commissioning of a 3 stage crushing and milling circuit at its Boddington Gold Operation in Western Australia. The Boddington ore has been recognized as one of the hardest and most abrasive ores treated to date and this played a pivotal role in the selection of crushing and HPGR technology for this operation as opposed to the more conventional SABC circuit. This paper will examine the scale up from laboratory to pilot plant and full scale operation of the crushing circuit. There have been many challenges to overcome in the first 18 months of operation; however, the HPGRs have in general met design expectations and performance is expected to improve further with ongoing design changes

Jan 1, 2012

By Mohsen Amir-Rahmat

The ore of Sarcheshmeh copper deposit that has been located in the south ?east of Iran, contains four type of rock that they have their specific hardness and strength according to their alteration type and mineralization. Blasting of these various types of mine rocks prepares various types of size for the product of mine as the feed of concentration. Along the crushing of this feed a few factors effect on the efficiency of the crushing unit. The aim of this project has been the consideration of the effect of ore size on the efficiency of crushing unit. For this investigation along the year 2000 A.D., six sample from feed and six sample from product of crushing unit have been prepared. The results of the screen analyze of these samples has shown that the size of feed has been lesser than the primary plan and the size rate of the product has been bigger than the primary plan. Also in this research the effect of feed size on the quality of product size has been considered.

May 1, 2003

By David Stephenson, Hugo Granados, Steven Klohn

"HudBay’s Constancia project is a copper molybdenum concentrator located in southern Peru. In 2010 Ausenco was contracted to perform a feasibility study optimization review which resulted in an improved design with significantly increased throughput capacity at a minimal increase in capital cost. Construction began in 2012 with commercial operation commencing in May 2015. This paper outlines the process plant design as well as describing the plant’s major equipment selections, start-up and early operations experiences.IntroductionHudBay Mineral’s Constancia project is located at 4200 meters above sea level (masl) in southern Peru, approximately 630 km south-east of Lima, Peru. The property can be accessed by road from Cusco, Peru, (approximately 110 km to the north), or from Arequipa, Peru (approximately 215 km to the south). Matarani, accessed via Arequipa, is the closest port.Constancia is located within the Yauri-Andahuaylas metallogenic belt. The region contains several large copper-gold-molybdenum porphyry deposits such as Antapaccay (by Glencore) and Los Chancas (by Grupo Mexico), and copper skarn deposits such as Tintaya (by Glencore) and Las Bambas (by MMG). Constancia’s ore reserves contain copper and molybdenum with trace amounts of gold and silver.Ore is mined by an open-pit operation. The process plant recovers copper and molybdenum concentrates, storing tailings in a conventional tailings management facility. Infrastructure at the site includes a grid power supply (via a 70 km overhead transmission line from Tintaya), water supply, workshops and an accommodation camp. Mine life is 22 years.Site construction works began in 2012 with first copper concentrate produced in late 2014. The project was executed for approximately 1.75B$USD.Ausenco’s design approach focussed on developing a capital efficient copper molybdenum concentrator. This paper outlines key features incorporated in the concentrator design, plant layout and equipment selection, as well as start-up experiences and early operational results."

Jan 1, 2016

By N. A. White

Whereas the ultimate world supply of energy minerals-defined as fossil fuels and fissile materials - is controlled by geological factors, the actual supply at any particular time is controlled by economic feasibility, technological innovations and /or political decisions. This paper identifies and discusses the principal uncertainties surrounding the international availability of energy minerals from now until the end of the century. A brief comparison is also made between energy and non-energy minerals. Genuine shortage s of energy minerals are now of a very long-term nature, whereas artificial ones may occur at any time and have a serious effect on the world economy due to the dependence of most OECD countries on imports of energy mineral . This paper argues that events over the last decade, such as the demand for a New International Economic Order, the OPEC increase in crude oil prices and the growing international lobby on environmental issues especially relating to nuclear safety - will progressively lead to a major, long-lasting transformation of the energy scene world wide. This transformation will encompass demand, in terms of conservation and efficiency, the supply mix of the various energy minerals , the supply system and the structure of the different energy industries . It is already affecting the role of governments and reaching into the question of national sovereignty both of developed countries, such as the U.K., Norway and Australia, and the developing countries, thereby making energy minerals a key area of international relations.

Jan 1, 1978

By Jan E. Nesset, Phillip J. Mackey

"Studies have shown that there is a correlation between commissioning and start-up time, i.e. time to reach full plant design capacity, and the degree of innovation and technical/engineering uncertainty in the project design. The paper describes the types of start-up curves for plants according to the level of technology or uncertainty in the process design. The need to properly describe and understand the commissioning and start-up time is examined using these curves and the importance on project success is highlighted. A number of case histories of recent mining and metallurgical projects are also reviewed. Finally, the paper reviews how to better assess the level of start-up uncertainty associated with a project and makes suggestions for decreasing the commissioning time due to technological risk.INTRODUCTIOThe start-up of a new mining and metallurgical facility, a much anticipated event, is a critical step in the life of such a project. Achieving a successful start-up and reaching the design capacity on-time requires careful planning, a thorough understanding of the key technological and engineering components involved and a well-trained and adequatelystaffed start-up crew. In this paper, some of the aspects related to start-up of a mining/metallurgical project will be explored, and in particular, the impact of the technology component will be examined. In order to illustrate this, a number of case histories based on recent mining and metallurgical projects will be discussed. Ways of assessing and understanding the uncertainty associated with technological issues related to start-up of a mining and metallurgical plant will also be examined.The history on mining and metallurgy is full of success stories of great mines and mills that are now considered “company makers” (well known examples of such successes include the Horne mine for Noranda which had a 1 year start-up in 1926-27, the Dome mine for Placer Dome, the Grasberg deposit for FMI in Indonesia). Less well documented are specific studies relating to plant start-ups and what constitutes a success or a failure, however there are a few notable references in the literature and these will be reviewed."

Jan 1, 2003

By John Lindsay

Outline ??Recovery plant requirements and concepts ??Common recovery plant unit processes ??Recovery plant design considerations ??Peripheral issues Process Design ??Liberation ??Separation ??Recovery Processing ??Density 3.5 g/cm3 ??Luminescent under x-ray ??Hydrophobic (non wettable) surface ??Non-magnetic ??Inert to strong acids / bases

Apr 1, 2005

By E. Engelbrecht

"A pressure non-oxidative leach is employed at Anglo American Platinum Base Metal Refiners to extract nickel from a slow cooled matte. The design base requires two 80 m3 autoclaves in parallel to achieve a nickel extraction of 60% at the nameplate capacity of 32.4 ktpa nickel plated. Isothermal modelling of mineralogical and chemical concentration profiles, through a reactive mass balance, permitted rate constant parameter estimation and selection of the most probable reaction pathway. The model was validated with plant data up to a capacity of 26 ktpa Ni plated and suggested by extrapolation that nameplate capacity may be viable through one 80 m3 autoclave.INTRODUCTION Anglo American Platinum Base Metal Refiners is situated on the outskirts of Rustenburg in the North-West province of South-Africa. The refinery produces nickel cathode, copper cathode, cobalt sulphate powder, covellite rich copper pressure leach residue and bulk sodium sulphate through an integrated circuit that refines slow cooled converter matte. The converter matte is milled, non-magnetics are separated as solid nickel copper matte (NCM), and the magnetics are leached yielding a pressure vessel liquor (PVL). The remaining solid platinum group metals (PGM) concentrate after leaching is sent for downstream processing in the Precious Metals Refinery (Hofirek & Kerfoot, 1992). The work presented here is applicable to the base metals refinery which receives the two base metals feed stocks NCM and PVL. In 2009 the capacity of the refinery was upgraded from 21 ktpa nickel cathode plated to 32.4 ktpa. This paper deals with evaluating the capacity of the pressurised non-oxidative nickel leach (NOX) process which accounts for at least 28% of the nickel leached from NCM by design. The NOX design base requires two 80 m3 autoclaves divided into four compartments operated in parallel at 155°C and 600kPa(g). Elevated temperature is required to speed up the leach kinetics of particularly nickel and iron which are trapped in slow leaching mineralogical phases namely millerite and bornite, (Dinham, 2006). The stated equivalent capacity for the NOX configuration was 32.9 ktpa nickel plated at first pass nickel and iron leach efficiencies of 60% and above 80% respectively and is a key step for the selective removal of iron (Bryson, Hofirek, Collins, Stiksma, & Bereaowsky, 2008)."

Jan 1, 2017

By Dave Bulled

"This paper describes the design of an SABC grinding circuit using CEET technology applied to grindability data produced from testing 100 samples and distributed across the blocks of a mine plan using a geostatistical approach. The data distribution required the identification of the location of the sample points and a geological plan of the 130 million ton Ruby Creek orebody together with a mine plan of about 11000 blocks to be mined during the proposed 18 year life of the mine. The mill design was then made with consideration for the estimated hardness of each block in terms of both SAG and Ball milling with allowance for annual periods when the ore is harder to grind. Operating specifications were selected to achieve an optimum of capital and operating costs through use of the CEET program. The geostatistics assigned the statistical error that arises from having a limited amount of sample testing data to the hardness estimate of each block of ore in the mine plan. The final design could then include a quantification of risk and determination of safety factors based on the accuracy of block hardness estimates and CEET model fitting.INTRODUCTIONThe traditional approach to plant design involves the extensive testing of a single large composite sample or a small number of composite samples that are reputed to represent the ore body. It is accepted that the tests used can accurately measure in the laboratory the grindability of the sample by a process representing that to be used in the plant. The size of equipment required to achieve a specified throughput and product size is then calculated from one of a variety of models that have been developed by metallurgists over years of trial and error. Since these tests and models are tried and tested, they are accepted as reasonably precise; however during the operation of the resulting plant the design is sometimes found to be inadequate. It is then suspected that the flaw in the design process lies in the samples not being sufficiently representative of the ore body, since using only a single or small number of composite samples does not recognize the variability of the hardness of the ore, nor does it allow for the lack of precision in the hardness value used in the design.This paper outlines a design procedure suited to an orebody that is described by a geostatistical analysis of a reasonably large number of small samples of drill core. The analysis required the identification of the location of the sample points and a geological plan of the orebody, together with a mine plan of the blocks to be mined during the proposed life of the mine. The mill design was then made using the estimated hardness of each individual block with an allowance for annual fluctuations in the grindability of the ore. The geostatistical analysis assigned a statistical error to the hardness estimates of blocks and of each production year such that the final design included risk estimates and safety factors based on the possible errors that arise from having a limited amount of sample data (Kosick et al. 2002)."

Jan 1, 2007

By Donald O. Downing

"IntroductionThis paper provides an overview of the coal mining industry in Canada with a description of current circumstances. The Canadian industry is placed in a global context and the future prospects of the industry are described. The export market is very important to the future of Canadian coal production and the essential aspects of the market are explained. Future prospects are very much tied to metallurgical coal exports and some key characteristics of that market are discussed, including major technological changes in the industry. Stability in 1996The Canadian coal industry enjoyed another strong year in 1996 continuing a trend established over the last four years. The strength of the industry is based on a stable domestic industry and a relatively healthy inter- national market. The figures bear out these statements. In 1996 total production reached 75 million tonnes and consumption was 52 million tonnes. The major markets for coal in Canada are electricity generating stations (Alberta, Saskatchewan, Manitoba, Ontario, New Brunswick, Nova Scotia) and the steel industry in southern Ontario. Approximately 11 million tonnes of coal were imported and exports reached a new record of 34.5 million tonnes, mainly from western Canada. Canadian Coal FlowsCanada represents a unique case in the coal world because we both import and export coal (Fig. 1). The reason for this apparent dichotomy is Canada’s geography. Eastern Canadian coal markets are located closer to the eastern United States coal fields and are basically served by them. This is true for both thermal and metallurgical coal. Major imported coal users are the steel industry, electricity generators and other industry including the cement industry in southern Ontario, Quebec, New Brunswick, with a little coal imported into Manitoba. Only about 2.2 million tonnes of western Canadian coal move into the east, including both lignite and bituminous coal."

Jan 1, 1997

By Valentin Choquenaha Bombilla, Oscar Alvarez Muiloz

"Tintaya’s basic production line is copper concentrate, which has an important gold content. The process used is flotation; the objective of the metallurgical department is to obtain the best results in the copper recovery without neglecting the gold, using very specific reagents. Copper recoveries are considered high, nevertheless every day emphasis is placed upon increasing those recoveries. Regarding gold, optimum recoveries could not be achieved with flotation; and implementation of a gravity circuit was considered.According to microscopy studies, the coarse and very fine grains of gold in native form are lost to tails. The native gold due to its high specific gravity is concentrated at the underflow of the cyclone, remaining in the circulating load of the circuit. It reaches three times the concentration compared to the head grade entering the ball mills. This re-circulation generates very fine and laminated gold particles inside the ball mill, passing to the classification stage making a short circuit to the overflow of the cyclone.The very coarse gold particles as well as the thick flakes of gold do not react favorably to the conventional flotation process; thus studies that have included gravity separation have been conducted to increase the gold recovery. Part of the research included concentrating tables, jigs, and Knelson Concentrators. The Knelson Concentrator proved to be the best selection in terms of metallurgical performance and recoveries considering the throughput and operation conditions of the Tintaya Plant.The gravity concentration circuit with the Knelson Concentrator was commissioned in BHP Tintaya in October 1998, as per the flowsheet shown later on. Presently the global gold production surpasses any estimated expectations.Present efforts are directed towards showing the evaluation and optimization of the different parameters that govern the performance of the Knelson concentrator, as well as illustrating the difficulties and successes throughout the operating period.In the first year of operation 200 tons of gold concentrate have been produced with an average concentrate grade of 320 gramdton, having paid back in full the cost of the automated KC-XD- 48 Knelson Concentrator, the peripheral equipment, and the cost of the installation."

Jan 1, 2002

By D. Bois, P. Poirier, B. Bussière

Environmental desulphurization is an attractive alternative for the management of acid generating tailings. Bulk sulphide flotation is the most commonly used method to produce desulphurized tailings, as shown from many previous works. This process can reduce the volume of problematic tailings to manage by making a sulphide fraction concentrate. The desulphurized tailings can then be used as construction material for an engineered cover to prevent acid mine drainage. In this paper, the results from different laboratory and pilot scale flotation tests are presented. These results confirm that low sulphide non-acid generating tailings can be produced by froth flotation. It is also demonstrated that sulphide concentrates obtained from desulphurization mixed with the appropriate binders can be used as feed material for paste backfill. From previous work on the evaluation of operating and capital costs of the desulphurization process for different ore types, the use of desulphurization as a tailings management approach was studied for several scenarios. The desulphurization process was then compared with other technologies (underwater disposal, engineered soil cover) currently used to prevent acidic drainage (AD) for a new mining operation. Results show that partial or total desulphurization are technically and economically viable options to manage tailings during mine operation. Mine waste managers should consider desulphurization as an efficient technology.

Jan 1, 2005

By D. Roy Eccles

A multi-element geochemical response, with contrasts of up to 29 times background, was obtained in soil above the Mountain Lake Diatreme, northwestern Alberta. The overall geochemical signature is indicative of an ultramafic source; geochemical responses contain elevated concentrations of Co, Cr,O, Cu and Ni with the presence of high Ba, Ga, HI, PO,, Rb, Ta, Ti and light rare earth elements suggestive ofa kimberlite or lamproite body. The shape, or morphology, of the enzyme leach-based geochemical signature over the Mountain Lake Diatreme combines moderately strong to strong oxidation halos, or a rabbit's- ear geochemical profile, with a sharply-defined apical geochemical profile. Because some Alberta diatremes discovered to date form positive topographic highs, the resultant geochemical signature may express the soil development profile that forms directly on top of kimberlitic and lamproitic bodies. The enzyme leach technique, which has proven to be a useful tool in base metal, precious metal and petroleum exploration, may have a significant impact on exploration for kimberlite, lamproite and related rocks in Alberta by providing industry with a useful and cost effective tool to probe blind and/or buried anomalies identified by airborne and ground magnetic surveys in areas of glacial overburden.

Jan 1, 2001

By D J. Murray

This paper outlines the principles of friction hoisting and the components involved, and gives a description of a specific mine hoist. Friction hoisting is compared with conventional drum hoisting, and the depth of shaft at which friction hoists become more economical than drum hoists, with respect to power consumption, is determined. Introduction T HE purpose of this paper is to outline the principles of friction hoisting, to describe the components and to show the advantages of multi-rope friction hoisting. Some calculations are made to show that the power requirements and the initial costs of friction hoists are less than those of conventional drum hoists, once a certain depth of shaft has been reached. The use of multi-rope friction hoists is gradually superseding the employment of the conventional drum hoist in many parts of the world. It results in heavier payloads from deeper levels, an increase in shaft safe-ty and a more compact installation for protection against adverse weather conditions. It was observed that where drums and friction sheaves exceeded 30 feet in diameter, a number of mechanical disadvantages were being experienced;

Jan 1, 1965

By W. N. Hamilton

As a result of a test-drilling program conducted by the Research Council of Alberta in 1968, a gypsum deposit averaging 30 feet in thickness, with a chemical purity of 84 per cent gypsum, has been proven to underlie the Clearwater River valley for a distance of 18 miles at depths ranging from near-surface to 300 feet. This and other subsurface deposits in the vicinity of Fort McMurray, Alberta are the product of local hydration of anhydrite beds believed to be the water-insoluble remains of the leached Prairie Evaporite formation of Middle Devonian age, the thick salt section of which is preserved down dip. The effects of salt solution are seen in the disturbed bedding and the intermixture of greyish green shale with gypsum in the core, the shale content being responsible for the rather low chemical purity of the deposit. A similar gypsum deposit, but probably of higher purity, is postulated to occur beneath the Athabasca River valley about 60 miles north of Fort McMurray.

Jan 1, 1969

By R. Tyreman, G. Ritson

"The Red Lake Mine is situated in Balmer Township, Red Lake area in northwestern Ontario. It is an underground mine that has been in production since 1948. The property was originally known as the Dickensen Mine and was shut down in 1996.A feasibility study was carried out in 1998 and it was determined that a new mill should be constructed with a throughput rate of 600 stpd. The life-of-mine average gold grade was projected to be 1.35 oz/t with gold predominantly associated with arsenopyrite and pyrite. Metallurgical testwork indicated that the optimal flowsheet for gold recovery would include an autoclave for oxidation with a carbon circuit for adsorption. To limit capital cost and establish cashflow, the mill was constructed without an autoclave. The recovery by gravity and cyanidation was projected to be 83%. A flotation plant was constructed at the tail end of the circuit to recover the additional gold associated with sulphides from the leach circuit tailings. This material is being stockpiled onsite for future oxidation treatment.Detailed engineering was started in early 1999 and the first gold was poured in August 2000. One feature of the project was the use of Contact Lake equipment from Cameco’s Contact Lake project. The entire mill was purchased and equipment re-used where possible. The capital cost for the process facilities was C$3 1.5 million."

Jan 1, 2001

By G. Major-Marothy

"INTRODUCTIONA beneficiation plant to upgrade earthy iron ores is being installed by the Iron Ore Company of Canada in Sept-Iles, Quebec.The crude ore for the plant will come from the Knob Lake area, located in Northern Quebec, where mining has been in progress since 1954.Some 170 million tons of ""direct 11 ores have been mined and shipped in the past eighteen years, with an overall silica content of 7 to 8 percent. No beneficiation - except the reduction of the top size to about 2 inches - took place during this period, but extensive research work has been carried out, in order to find a feasible process.Since “washing"", gravity separation, roasting and magnetic separation experiments did not indicate positive enough results, flotation was tried and found to be feasible.The beneficiation complex being installed will consist of grinding, flotation, dewatering - i.e.: thickening, filtering and drying - balling feed preparation, and agglomeration - i.e.: balling and induration.This process will result in a product superior to the ""direct shipping"" ores and will also expand the ore reserves by allowing material with a higher silica content to be utilized.THE OREThe Knob Lake ores are grouped by mineralogical composition and by grade.BLUE ORES, representing roughly two thirds of the reserves, carry their iron content mostly in the form of massive, blue hematite and martite.YELLOW ORES, about one sixth of the reserves, have predominantly hydrated iron oxides as the iron bearing minerals.RED ORES, the other sixth of the reserves, carry the iron mostly in the form of red hematite.The gangue in all ores is mainly quartz, but aluminum oxides and hydroxides are also present, particularly in the red ores."

Jan 1, 1972

By Sejong Kim, Younghoon Moon, Youngseon Lee, Eunyoo Yoon, Yonghyun Song

"Mg alloy has a high specific strength, however, their thickness reduction was limited on most parts because of their poor stiffness. Since the modulus of rigidity is an intrinsic property, improvement of modulus of rigidity to the enhancement of stiffness is impossible. Therefore, the modification of shape and structure is available method to enhance the stiffness of real part fabricated by Mg alloy sheet. There are many thin walled parts which are located in outer section of electromagnetic system.Poor stiffness is often shown on wide surface area part with steel sheet, which has also high modulus of rigidity. In these cases, various groove patterns are used to increase the stiffness of part. However, some different methods have to be used when general groove pattern can’t be used. So, we would like to propose some new method to high stiffness on thin walled precision forging of Al or Mg alloys.An effect of proposed method on stiffness enhancement can be confirmed by fabrication of prototypes as well as structure and forming analysis based on FEM."

Jan 1, 2015

By T. A. Kirk

"The Linatex Dewatering System is a compact, low capital and maintenance cost matched set of processing equipment suitable for solids recovery, dewatering and desliming sand-like materials in the range 3/8"" to 325 mesh ( 1). Since its introduction to North America in the early 1970s, various elements of the system have been successfully installed in a variety of applic11tions both in Canada and the U.S.A. Examples are chosen from the coal, fine aggregates, iron ore and industrial minerals industries.II. Elements of the Linatex Solids Recovery System(A) The Linatex Separator (See Fig.I)The Linatex Separator, which is the heart of the system, is a specialized type of hydrocyclone designed to give a self regulating rope discharge product. It has the familiar cyclone geometry of cylindrical and conical section, tangential inlet, apex and vortex finder. The apex is enclosed in a unique patented automatic underflow regulator consisting of a collapsible rubber sleeve, and the overflow line is a siphon-leg, with a controlled air bleed valve. The siphon leg is adjusted so as to balance the internal negative pressure acting as a closing force on the underflow regulator against the mass of slurry pressing down on it from the cone section of the Separator. With correct adjustment the underflow regulator will close drip-tight on a water only feed. As solids accumulate in the apex of the cone the weight of solids counterbalances the vacuum and cat1ses the underflow regulator to open and discharge classified material at a controlled density."

Jan 1, 1978

By Jan E. Nesset

It is just over 100 years since the practice of blowing small bubbles into a mixture of ground ore and water revolutionized the mining industry, resulting in uneconomic deposits becoming highlyprofitable mines, along with the inevitable lawsuits over this new technology called froth flotation. To this day, the viability of many mining projects rests largely with the ability of flotation to effectively capture the valuable minerals and reject wastes. Remarkably, bubble behaviour in flotation has not been well understood until very recently with the advent of new sensor technologies that can be brought directly into the operating plants. This presentation will review the importance to the mining industry of understanding bubbles, highlight these new technologies and illustrate, with examples, how paying attention to your bubbles will pay off.

Jan 1, 2009

By Marco A. Vera

"This paper investigates the froth function in flotation and the associated upgrading process. Flotation literature has revealed that one of the main functions of the froth phase is the cleaning of bubble-particle aggregates by rejection of entrained material. The cleaning and transport processes across the froth phase exert straining forces on these aggregates on their way up to the froth surface. These forces will impact on the recovery of bubble-particle aggregates.The grade at the top of the froth (TOF) is a parameter related to the quality of particles collected by bubbles in the pulp zone (true flotation). It has recently been demonstrated that TOF corresponds to the maximum practically attainable grade described by the recovery-grade (or enrichment ratio) curve. TOF lumps all the processes experienced by the bubble-particle aggregates before reaching the launder concentrate. This paper describes a methodology for quantifying flotation performance by means of the top of the froth sample - a touch of froth.INTRODUCTIONFroth flotation may be the most important mineral processing technique, but its theory is complex and is not completely understood even though many aspects have been studied and reviewed (Teague, 1998; Wills, 1992).Two distinct particulate systems prevail in the flotation process: a pulp phase and a froth phase (Figure 1). The pulp zone had been studied extensively; however, it is only recently that techniques to measure the froth zone performance have been developed (Contini et al., 1988; Falutsu and Dobby, 1992; Feteris et al., 1987; Seaman, 2002; Vera et al., 1999b).Flotation involves a number of mass transfer processes, occurring in the pulp phase and the froth phase. The formation of the froth and its subsequent removal are considered to be two important steps of the process. Phenomena that occur in the froth phase are known to affect flotation performance significantly (Cutting et al., 1981).Because the froth has a high free surface energy (as a result of the extensive interfacial surface between liquid and air), it appears thermodynamically unstable. The foaming is a dynamic balance, as new bubbles are added continuously from the pulp, while others disappear from the top. Under steady-state conditions, the volumes of added and subtracted air are equal (Booth, 1953)."

Jan 1, 2003