Search Documents

By G. Thom, A. Kay, J. B. Hyde

"This paper will initially outline the specific types of copper castings used in blast furnace iron production. Tuyeres, tuyere coolers and stack cooling plates will be discussed in some depth, with particular reference to their dimensional configuration and purpose.Following this, the failure of such cooling members will be discussed, with special focus on tuyeres. Tuyeres are the most common casting which often requires replacement. Reasons for failure and its effect on operations will also be included.The latter sections of the paper will deal with the strict specifications demanded by ironmakers regarding copper castings. The justification for such rigid demands will be explained through the material presented earlier in the paper.IntroductionThe modern 5000-tpd blast furnace, worth millions, is a large capital investment to be sitting idle. Consequently, ironmakers strive to minimize the loss in iron production and revenue from furnace downtime. Two major causes of downtime are furnace relines and shutdowns to replace damaged tuyeresor tuyere coolers. Copper ancillaries are important items in the production of iron. They are consumable items, therefore they contribute to the campaign life or to the downtime in blast furnace production.Several combinations of lining and cooling systems have been used with varying degrees of success. Blast furnace refractories have evolved from ceramic to carbonaceous linings. The Russians and Japanese have successfully introduced stave-cooled furnaces that may have several forms, such as evaporative cooling. Stelco has two furnaces which use the Russian-designed cast iron system. However, this paper will be confined to the use of copper cast cooling members in a conventional internally cooled furnace.Figure 1 is a schematic cross section of the E blast furnace. The three major sections of a blast furnace-the stack, bosh and hearth-are identified. Further, the locations of the various copper members are indicated. This furnace produces an average of 5300 tons of hot metal per day."

Jan 1, 1982

By Jeff R. Reinson

The Diavik Diamond Mine is producing diamonds from two orebodies, the A154 South and A154 North kimberlite pipes, discovered beneath the waters of Lac de Gras. Innovative dike technology with appropriate water collection and treatment systems allowed Diavik to start open pit mining of the ore bodies in 2002. To allow planning, engineering, and implementation of sufficient water handling infrastructure, reasonably accurate estimates of groundwater inflow quality and quantity over the life of mine are required. Prior to mining, a numerical model using the continuum approach was developed for regional and site wide water management. After approximately two years of mining, groundwater inflows to the pit were found to exceed those predicted by the base case hydrogeologic model. The most likely explanation was flow through Dewey?s Fault zone. As this fault was not explicitly accounted for in the model, a detailed hydrogeologic investigation was conducted to evaluate its geometry and hydraulic properties. A multi-disciplined approach was used and involved core logging, fluid logging, geophysical logging, packer testing, a pumping test, and water quality sample collection. The results of the field investigation were used to update the conceptual and numerical models and to develop a Discrete Fracture Network (DFN) model to address small scale problems such as flow into future underground drifts. The updated numerical hydrogeologic models predict that up to 70 per cent of the groundwater inflow to the A154 N/S open pit is through the relatively narrow fractured rock zone associated with Dewey?s Fault. Consistent with the continuum model, the DFN model predicts that inflow to a drift excavated in Dewey?s Fault will be approximately 10 times the inflow to a drift excavated in competent rock. The DFN model provides a better understanding of the distribution of these inflows on a local scale over the length of the drift.

May 1, 2006

By Jack Zhang, Chuck Edwards

"The versatility and specificity of rare earth elements (REEs) have led to their use in an ever increasing variety of applications in new technologies. Consequently, demand for REEs has increased significantly. However, to separate REEs safely and effectively is a complex and expensive process. While China has consistently invested in R&D of REE processing technologies, there have been only sporadic activities in REE mineral processing in North America in the past 20 years. This paper presents a review of REE mineral processing technology, providing an update on current capabilities in REE mineral processing. This paper reviews REE extraction from the major commercially valuable REE-bearing minerals such as bastnaesite, monazite, and xenotime, and also from the ion-absorption type of REE deposits. Currently, there are four major REE mining areas in China, one in the United Sates, and one in Australia. A review of the REE extraction processes in these major REE mining areas closes out the paper.INTRODUCTION The rare earth elements (REEs) include the 15 lanthanide elements, plus yttrium and scandium. The lanthanide elements are normally categorized in two groups: the light rare earth elements (LREEs), i.e. lanthanum through europium (atomic number (Z) = 57 through 63); and the heavy rare earth elements (HREEs), i.e. gadolinium through lutetium (Z = 64 through 71). Yttrium is usually grouped with the HREEs due to similarity in physical and chemical properties. Table 1 lists the REEs, atomic numbers, and abundances in earth’s crust (Taylor and McCleannan, 1985). Promethium is the rarest due to lack of stable isotopes. REEs with low atomic numbers are more abundant than those with high atomic numbers. More interesting is that the REEs with even atomic numbers are much more abundant than adjacent lanthanide elements with odd atomic numbers as shown in Table 1."

Jan 1, 2012

By Henri F. Letient

At the 25th Annual B.C. Mine Reclamation Symposium in September 2001, Huckleberry Mines Limited received the Jake MacDonald Reclamation Award for its exemplary mine waste management plan, conceived to prevent the onset of acid mine drainage and facilitate reclamation of the site. The mine is an excellent example of a total mine waste management plan, with all materials scheduled in detail for the life of the mine. The filling plan for the waste management facility takes into consideration the requirement for permanently flooding the potentially acid generating rock. From an acid generation point of view, the tailings fall in the zone of potentially acid generating material. To avoid long-term ARD concerns, it is planned to float pyrite out of the tailings towards the end of the mine life, thereby generating a non-acid generating tailings stream which will be used to cap the deposited mine waste. The pyrite-rich tailings will be discharged into the deeper portion of the impoundment. On closure, a permanent water cover will be maintained over the mine waste. Only beaches of non-acid generating tailings will remain exposed. Mining will be phased to also allow one of the pits to provide storage for potentially acid generating rock and to be flooded at the end of mine life.

May 1, 2002

By Dave Bulled, Khiratt Husain

"The use of High Pressure Grinding Rolls is gaining significant interest as a replacement for SAG milling in the comminution of hard rock ores because of the potential for reduced costs in terms of energy and grinding ball consumption. Estimation of expected energy consumption for fullscale operations has conventionally involved the testing of a few fairly large samples in pilot scale HPGRs. This paper describes the development of a small-scale batch test method for determining a work index for HPGR of a large number of samples that can be used to show the variability of the ore as an integral part of a geometallurgical approach to circuit design and production forecasting.The test equipment that was developed comprises a hydraulic press with adjustable pressure operating on small batches of ore in a locked cycle test procedure. A work index measurement was determined that links the specific energy consumed in the test to the breakage achieved such that the index can be used to predict comminution energy requirements.The measurements were calibrated against laboratory scale HPGR equipment to develop a model for design and forecasting that includes crushers, HPGRs and ball mills in a complete comminution circuit.INTRODUCTIONEstimation of the expected energy consumption for full-scale HPGR operations has conventionally involved the testing of a few fairly large samples in laboratory and pilot scale machines (Danilkewich, 2006). With the financial input of five mining corporations, SGS Lakefield Research has developed a small scale test capable of providing relevant information on the variability of energy consumption and size reduction from drill core samples. It is our intention that the values measured in the test will be scaled up, through benchmark comparison with pilot sized and full sized HPGR units, to allow plant design and throughput forecast on a block by block basis of the mine plan using a new CEET program. CEET® (an acronym for Comminution Economic Evaluation Tool) is an advanced grinding design and performance predicting tool that uses energy relationships to model the performance of SAG / Ball mill circuits."

Jan 1, 2008

By Charles G. Kemsley

IN January, 1939, Dome Mines, Limited, purchased a few bars of an alloy drill-steel for the purpose of testing its fatigue resisting qualities as compared with those of a straight carbon-steel then in general use at the mine. A steel of the following analysis was selected: Carbon 1.00% Sulphur 0.022 Chromium 1.26 Silicon 0.17% Phosphorus 0.028 Vanadium 0.1 Manganese 0.32% Molybdenum 0.30 This steel has a tensile strength of 180,000 lb. per square inch and a Brinell hardness of 380, as compared with a tensile strength of 114,000 lb. per square inch and a Brinell hardness of 230 for the standard carbon drill steels, in the as rolled' condition. The result of this test showed that about five times as many runs could be obtained from the alloy steel before failure from fatigue. It was therefore decided to replace gradually the one-inch quarter-octagon carbon steel, then in use, with seven-eighths quarter-octagon alloy steel. In January, 1940, six machines was placed on the seven-eighths steel and this was gradually increased until now (March 15th, 1941) fifty per cent of the steel being used is alloy steel. An O'Donovan furnace is used at the Dome for heat-treating their carbon drill-steel. In this furnace, a magnet withdraws the steel when the critical temperature has been reached, and the operator then places the steel in the quenching tank. Not being able to use this furnace for the alloy steel, the management felt that some means should be developed to determine the quenching temperature without depending upon the operator's judgment of the correct 'colour'. With the assistance of the Canadian General Electric Company, a radiation-type vacuum thermocouple pyrometer was adapted to this purpose, with excellent results; in fact, with this instrument no previous experience in hardening is necessary and results are remarkably uniform.

Jan 1, 1941

By Jan E. Nesset, Julie Fournier, Jorge Torrealba, Colin Hardie

"Gas dispersion studies have been used to benchmark and optimize plant flotation performance for more than a decade, although this technology is not as widely in use as it likely should be based on the significant improvements that have been reported. Part of the reason may be a general lack of awareness within the industry of just what these improvements have been. This paper reviews a number of the reported case studies, groups them into categories of improvement, and draws some general conclusions. The paper will be of interest to plant engineers and technology providers seeking new approaches and tools for improving their own and clients’ processes.INTRODUCTIONThe sector of flotation hydrodynamics that is now known as gas dispersion technology, and the corresponding terminology, had its beginnings in the 1980’s and early 1990’s in the laboratories of McGill University where the students of Prof. J.A. Finch and Dr. C. Gomez conducted studies of gas holdup, superficial gas rate and water recovery on laboratory flotation columns (Laplante et al., 1983; Xu et al., 1991;, Banisi and Finch, 1994; Finch et al., 1999; Nesset, 2011). Sensors were developed for gas holdup (eg), gas rate (Jg) and bubble size (Db) distribution (Tavera et al., 1996: Finch et al., 1999; Dahlke et al., 2001; Chen at al., 2001; Hernandez-Aguilar et al, 2002, 2005). The sensor measurements were rapidly adapted for use in mechanical flotation machines in plant environments (Gomez and Finch, 2002; Gomez et al., 2003; Cooper et al, 2004; Torrealba-Vargas et al, 2004; Nesset et al., 2007). Somewhat parallel developments were being conducted by Gorain and colleagues at the University of Queensland’s JKMRC on pilot and industrial flotation machines using the McGill approach but utilizing alternate sensor designs for eg, Jg and Db (Gorain et al., 1997, 1999; Schwarz and Alexander, 2006) to link flotation kinetics to bubble surface area flux (Sb). Early industrial applications were those led by the university teams from McGill (Canada), the JKMRC (Australia) and the University of Santa Maria (Chile) at plants in North and South America, Australia, South Africa, Asia and Europe. Industrial organizations that brought the technology on-board in the early 2000’s included Teck Resources (then Teck Cominco), COREM, Vale (then Inco), Anglo American Platinum. Several of the major flotation cell manufacturers also purchased the McGill bubble viewer technology for their own equipment studies. The sensors have continued to evolve with multiple and continuous measurement of Jg (Torrealba-Vargas and Finch, 2006, Bartolacci et al., 2008), gas holdup by acoustic means (O’Keefe, 2007) and a combined Jg-Db device called the Anglo Bubble Sizer (Harbort and Schwarz, 2010). A review of the gas dispersion technology use and development have been provided by Gomez and Finch (2002), Harbort and Schwarz (2010) and Nesset (2010)."

Jan 1, 2015

By R. J. Visintainer, W. L. Whitlock

"Difficulties with the sizing and operation of centrifugal froth pumps are common and the underlying fluid dynamics are complex. Design and selection often relies on previous experience, offering unreliable guidance for novel applications or unexpected problems. The current paper describes a program of extensive laboratory testing on froth handling centrifugal pumps, covering a range of flows, heads, speeds, viscosity, air content and froth stability. Variations in impeller vane design and the effectiveness of an airlock venting apparatus were also examined. The program resulted in a better understanding of centrifugal froth pump dynamics and insight for the troubleshooting of field applications.INTRODUCTION The Challenge of Pumping Froth In pumping mineral processing froth, the handling of large quantities of air within the fluid is often unavoidable. Efforts to reduce the amount of air present at the pump suction, while always recommended for improving pump performance, may have limitations. Some strategies may also carry an economic penalty, such as unwanted process dilution (e.g. due to water spray or injection), or increased capital cost of equipment due to oversized pumps, sumps and/or piping. Froth pumping losses fall into several categories, as described below and represented graphically in Figure 1. • Density effects: Entrained air reduces the pressure created by the centrifugal pump in direct proportion to the reduction in bulk density. This is not a true “loss”, since the head produced by the pump (in meters of froth), may remain unaffected. However, the reduction in pressure often leads to a corresponding increase in pump speed required to drive the system, which itself leads to increased NPSH required by the pump (NPSHR). Furthermore, by adding a gas phase, the overall volumetric flowrate is increased, assuming a fixed quantity of de-aerated liquid being handled. This leads to increased suction velocity which further reduces the NPSH margin by simultaneously increasing pump NPSHR and decreasing system NPSH available at the pump suction (NPSHA). • Viscosity effects: Increased viscosity introduces an additional factor in some froth pumping applications, such as oil sands bitumen froth. Losses result from increased shear stress within the fluid flow, which increase with flowrate. Viscosity also facilitates the formation of airlock by reducing turbulence and allowing individual bubbles to coalesce more easily within the flow stream. Finally, it increases pump NPSHR by increasing local pressure drop in the vicinity of the vane inlet edges. • Airlock effects: Also known as air binding, it occurs when air or gas coalesces within the pump suction or impeller passages and begins to collect there, held by buoyancy forces within the rotating flow field. In essence, the liquid “floats upwards” towards the pump suction against the outward directed centrifugal forces. The airlock acts as a blockage, with corresponding reductions in flow, head and efficiency. NPSHR also increases, due to increased velocity and distorted streamlines in the flow circumventing the blockage."

Jan 1, 2012

By Nick D. Rose

The importance of structural geology in open pit slope stability is overlooked in many mining operations due to pressures to cut costs and minimize mine personnel. As a result, mine geology staff are often unable to keep up with geological mapping of the pit slopes due to other day to day production oriented tasks. In some instances, key structural controls that contribute to slope instability may not be identified until after a slope instability has initiated, at which time it may be difficult or impossible to delineate these features in the field. Even for small slopes, understanding the engineering and structural geology of the rock mass, as well as the effects of groundwater and blasting practices, are of key importance to slope stability. Two case histories are presented as examples of mining operations that experienced slope instability with little more than anecdotal information about the structural and groundwater conditions encountered during mining. By conducting field reconnaissance, simple slope stability analyses and ongoing slope monitoring, practical remedial measures were implemented, allowing continued safe mining operation.

May 1, 2002

By D. Wolfe, R. Cleminson

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. The hydrotransport systems at Aurora experience high rates of wear, and mission lengths on current slurry pumps are nominally 1,500-2,000 hours. Recent work has enabled a better understanding of the significant adverse effect of large particle impingement damage to impeller vane leading edges - which is the known life determining issue for Aurora hydrotransport pumps. A new pump design has been developed and installed at Aurora, incorporating significantly increased impeller diameter and pumping vane lengths. The new pumps are expected to triple Aurora’s previous mission length for hydrotransport pumps. Part II of this paper will share actual hydraulic and wear performance observed in the first several months of operation, and draw comparisons relative to what was expected for these pumps in design / development.INTRODUCTION Slurry Pumps are Critical Equipment at Syncrude Slurry pumps are a key component in Syncrude’s operations. In a typical Aurora application, each 5000 HP pump stage helps move over 8,000 dry tonnes per hour of oil sand, plus an equal volume of process water that has been added to create the slurry. The average impeller life in oil sand hydrotransport service at Aurora has been nominally 1,500 to 2,000 hours, or 12 to 16 million tonnes of oil sand pumped. Generally, the slurry pump application at Aurora has proven very difficult to improve due to the unique combination of high sand abrasivity, 125 mm (5”) large particle top size (lumps), and high flow rate relative to basic pump size; a factor that results in unduly high impeller vane leading edge speeds for the service conditions."

Jan 1, 2014

?? Intro ?? Mass blast principle ?? LaRonde evolution toward mass blast ?? Overview ?? Mining method ?? Longitudinal ?? LaRonde evolution (2002 to today) ?? Drill and blast design ?? Consumptions and statistics ?? Mucking strategies ?? Case study ?? Examples ?? Conclusion ?? As underground mines extends to greater depths, few questions must be asked: ?? How to: keep operations safe eep operation effective reduce the cost maintain and control the dilution ?? Geomechanic method and practices; significant advances have been observed in the field of: ?? ground support ?? mining sequencing ?? Drilling and blasting; research and development has been less extensive, probably due to the following characteristics: ?? Drill and blast are mainly production-oriented ?? Drilling and blasting are more oriented toward productivity ?? Technology relies heavily on suppliers ?? Highly stressed ground conditions ?? generally help the explosives to break the rock for fragmentation ?? intensify over-breaks or blast-induced

Feb 1, 2008

By Barrie Robb

Outline 1. Mackenzie Aboriginal Corporation (MAC) 2. ACR background 3. ?Learning from Experience? project - What - Why - lessons 3. How Industry could contribute to sustainable Aboriginal communities 4. Concluding words What is the Mackenzie Aboriginal Corporation (MAC)? ? Aboriginal owned ? Established construction capabilities ? Commitment to development of northern resources ? Partners have extensive experience

May 1, 2008

By B. P. Simser, R. K. Brummer, A. Mortazavi, P. P. Andrieux

"A large-scale panel destress blast was fired at Brunswick mine in the fall of 1999 in order to reduce the ground stresses in a critically important neighbouring mining region. This work, sponsored by the Mining Division of CAMIRO and Brunswick mine, consisted in heavily choke-blasting — and subsequently leaving in place — a massive waste sulphide pillar in the southwest end of the 1000 m level. This paper describes the approach and design methodology used to try to maximize breakage in the rock mass in the area to destress, while minimizing damage to critical infrastructures in the vicinity. The loading operations, as well as the results of the blast — in terms of its field performances, as recorded by near-field blast vibration monitoring equipment, visual postblast assessments and measured impact on the regional stress field — are discussed as well. A brief comparison between the measured stress changes and inelastic numerical modelling of the test site is also presented.Un tir à grande échelle de relâchement des contraintes dans un pilier a été effectué à la mine Brunswick à la fin de l’automne 1999 dans le but de diminuer les contraintes de terrain dans une très importante zone de production adjascente. Ces travaux, financés par la division minière de CAMIRO et la mine Brunswick, consistaient à tirer violemment sans aucune face libre, et à laisser en place, un pilier de sulphures massifs au sud-ouest du niveau 1000 m. Cet article décrit l’approche et la démarche conceptuelle utilisées pour tenter de maximiser les fractures dans le pilier visé, tout en minimisant les dommages collatéraux à des infrastructures critiques se trouvant dans les environs immédiats. Les opérations de chargement des explosifs et les résultats du tir — en termes de ses performances, telles qu’évaluées par de l’équipement de monitoring rapproché des vibrations de tir, d’observations visuelles, et de son impact sur les contraintes de terrain locales — sont également discutés."

Jan 1, 2003

By M. W. Franklin, D. W. Hendriks

"Changing ore types, feed grades and c1rculat1ng loads are some of the many factors that can make flotation feed-back control difficult. To control a flotation circuit using conventional fixed-parameter control algorithms, one must either tune the controllers very often or tune the controllers to the middle of the normal operating range. The former approach is very time consuming, while the latter approach can lead to long periods of either very sluggish responses or highly reactive responses which can lead to instability. The problem becomes compounded if feed-forward variables are introduced, creating even more variables to tune. An alternative to a fixed-parameter control algorithm is an adaptive control algorithm. An adaptive control algorithm continuously retunes itself based on previous reactions to its changes. Feed-forward control also becomes much more viable because the algorithm will tune the feed-forward parameters and the feed-back parameters simultaneously. Using the combination of feed-forward and feed-back tuning is an effective way to decouple the loops needed in flotation circuits where one circuit feeds into another. The advantages of adaptive controllers over conventional controllers will be introduced through the use of a simulator. Also discussed will the be the implementation of adaptive controllers at Brunswick Mining and some of the modifications that are available to help solve more difficult control problems.Brunswick Mining is located just outside of Bathurst, New Brunswick. The concentrator processes approximately 10250 tonnes per day of ore that assays at approximately 8.9 %zn, 3.6 %Pb, 0.3 r.cu and I 00 gram/tonne of Ag. The four products produced are zinc concentrate assaying 51 %Zn, lead concentrate assaying 34 %Pb, copper concentrate assaying 21 %Cu, and a bulk concentrate assaying 32 %Zn and 18 %Pb."

Jan 1, 1986

?Why TSM in Canada ?How it was developed ?Architecture and Goverance ?COI panel ?Performance indicators and how they work ?External Verification ?Reporting ?The national organization of the Canadian mining industry ?Mining, smelting and refining of base and precious metals ?Mining of iron ore, diamonds, uranium, oil sands, coal and industrial minerals ?Many associate members ?www.mining.ca

May 1, 2011

"As mine head grades decline and orebodies become more complex, traditional mineral processing techniques and flowsheets to achieve saleable concentrate become more difficult to design and construct. Mines with lower quality concentrates or concentrates with penalty elements are particular under threat. The economics of these operations are far more susceptible to metal price, concentrate treatment terms and the availability of other, cleaner concentrates. Additional value may be realised for these orebodies through improved recovery by producing a low grade middling concentrate for further processing, in conjunction with a saleable concentrate.The most cost effective way to reduce impurity levels is to do so as early as possible in the mining value chain. Technologies such as fine grinding and fine particle flotation are well established as effective methods for impurity rejection in mineral processing. What is normally overlooked is how a hydrometallurgical process could also be integrated in the overall flowsheet to achieve higher overall recovery at the mill. In the base metals environment, this is mainly because hydrometallurgical processes are associated with production of metal or use of expensive and toxic precipitating agents once the minerals of interest are solubilised. These processes can be very expensive, particularly with rising power costs and poor economies of scale in capital costs associated with low production rates from middling streams.Glencore Technology (GT) has recent experience in the treatment of middling and low grade concentrate streams as well as tailings streams to compliment a concentrator flowsheet in a refractory gold and base metals setting. The value proposition is the isolation of a low grade middlings concentrate from the primary circuit or the tailings stream for upgrading to an intermediate product with an equal or higher grade than the primary concentrate to allow blending for sale. This allows plants to operate on a more favourable part grade-recovery curve while avoiding the expense of metal production. For existing operations this is particularly attractive since it can be added on with no process interruptions.Two case studies are examined showing flowsheets and costings to arrive at the value proposition of the GT low grade treatment flowsheet."

Jan 1, 2017

By S. D. Botts, F. Cantuarias

"The Antamina project, owned by BHP Billiton Plc, Mitsubishi Corporation, Noranda Inc., and Teck Cominco Ltd., is a $2.3 billion copper/ zinc project, located in the Ancash Department of Peru. The project consists of an open pit mine, a 70 000 ton per day concentrator, a 302 km long concentrate pipeline, port facilities, a new access road, power line, and town site. The project is designed to produce up to 1.5 Mtpy of copper and zinc concentrates over a 23 year project life, and will be the third largest producer of zinc and the seventh largest producer of copper in the world.This mega project is the largest mining investment in the country and, during its construction stage, was the most important construction project worldwide. On May 28, 2001, Antamina commenced testing operations and four months later, it reached commercial production. Antamina was officially inaugurated on November 14, 2001 by Peruvian president Alejandro Toledo.The construction stage of the project generated 8000 direct jobs, with a peak of 10 000 employees, and 30 000 indirect jobs. The permanent workforce consists of approximately 1650 employees, the vast majority of which are Peruvian Nationals, around 30% of whom came from the region where the deposit is located. Approximately 5600 indirect jobs were generated from the project. Independent sources state that Antamina increased the Peruvian mining exports by 30% (mining exports constitute 50% of Peru’s total exports) and Peruvian GDP by 1% in its first year of full operation in 2002.Since winning the privatization bid for the project in 1996, the company has implemented an approach to community development and environmental protection based on sustainable development principals. Throughout the development of the project, a number of initiatives have been undertaken to ensure full involvement of the local populations in community development activities and the company’s environmental program.Due to its size, difficult logistics, cultural considerations and financial aspects, the project has faced a number of unique challenges in the area of environmental protection and management of community interaction. Antamina has been innovative in its approach to these issues and, as a result, has set new standards in Peru for environmental and community management and sustainable development."

Jan 1, 2003

By D. Settles, R. Rose, P. L. Dunn

"A new mineral sands operation is being developed in Georgia by Southern Ionics, Inc. (SII). Prevailing mineralogy and certain design constraints required detailed testing and circuit analysis to create a robust separation processes. The floating wet concentrator plant (WCP) and mineral separation plant (MSP) flow sheets were designed based on historical testing information and recent SII test campaigns on various composite feed samples. The flow sheets were finalized through rigorous process and orebody sequence modeling.The process uses traditional physical separation equipment; however a new MT spiral, the MG12, was selected for use on board the WCP for roughing duty. The MG12 spiral is a two-stage, twelve-turn spiral that has been proven to achieve very high recoveries of heavy minerals. The floating plant includes feed desliming operations, a central MT surge bin for optimum spiral circuit feed control and ancillary operations for concentrate and tailings handling. Scrubbed heavy mineral concentrate (HMC) is then transported to the MSP for concentration of the titanium and zirconium bearing mineral fractions.The testing, flowsheet development, and plant design will be described and explained, and a brief summary of the current project status will be given.IntroductionSouthern Ionics Inc. (SII) is a privately held chemical manufacturing company, founded in 1980 by Milton Sundbeck. SII focuses primarily on the sale of specialty and intermediate inorganic chemicals. Core markets include cement and refinery catalysts, molecular sieves, zeolites, pulp and paper, pharmaceuticals, TiO2 and water treatment. SII is built on the four cornerstones of service, quality, technology and delivery with all SII facilities ISO certified and key products used in potable water treatment certified to NSF standards. SII owns and operates its own transportation fleet and is focused on being a low cost producer, committed to safety and the environment."

Jan 1, 2015

By G. R. Brough

"Today it is more important than ever to get the maximum possible return on capital invested in the processing industry. To this end the plant is often operated continuously and the choice of equipment is, consequently, extremely important.Screening spans a wide range of particle sizes and there are many different types of screening elements. The following types are common:1. Cloths and elements of rubber.2. Wire mesh screens with round wires.3. Wire mesh screens with profiled wires.4. Perforated steel plates.5. Elements of plastic.6. Gratings of steel beams.7. Gratings of iron rods.We would like to deal with two of these types namely rubber and briefly on plastics.We first introduced rubber screens to the Canadian Mining Industry in November, 1963. This stemmed from a conversation with the superintendant of one of Canada's largest screening plants containing 48 vibrating screens, with an average wire cloth life of 10 to 12 days. We contacted the manufacturer of rubber screen cloths who had supplied rubber screens to a mine in Northern Sweden for a 50,000 ton per day plant in 1951."

Jan 1, 1983

By Art Carino

"The McClean Lake operation is located in the Eastern Shore of the Athabasca Basin in northern Saskatchewan some 700-air kilometers north of Saskatoon. It is operated by Cogema Resources Inc., the major share holder of the joint venture consisting of Cogema Resources Inc., Denison Mines Limited and OURD, a consortium of Japanese utilities.The JEB mill is the first uranium mill to be constructed and licensed in North America within the last 15 years. The mill uses conventional uranium unit process but employs innovative techniques unique to the JEB mill.This paper presents brief descriptions of the various unit processes, the innovations and the commissioning strategies developed to achieve the designed production capacity in the shortest possible time.INTRODUCTIONThe McClean Lake ore body was discovered in 1979, followed by the discovery of the JEB ore body in 1982. From 1985 to 1990, a cluster of deposits named Sue A, Sue B and Sue C were discovered. Environmental Impact Assessment (EIS) of the McClean Lake project began in 1990 under a joint federal-provincial process. Following the public hearings in 1993, the governments gave approval to proceed with the construction of the project, subject to fulfilling licensing requirements.The McClean Lake ores are located in the uranium-rich geological region of Saskatchewan known as the Athabasca Basin, 700 air kilometers north of Saskatoon. The JEB mill is located near the mined out JEB open pit that is now used as the tailing depository.The approved mill has a production capacity of 6,000,000 pounds of U3O8 annually and is capable and licensed to process JEB, Sue A, Sue B, Sue C, McClean Lake, and Midwest Lake deposits. Although the EIS has been approved, Mining of the Midwest Lake deposit has not been approved at this time."

Jan 1, 2001