Search Documents

By M. X. Yao, Y. Ning, P. C. Patnaik, R. Liu, X. J. Wu

Stellite 712 composites were developed with the reinforcement of bare TiC or Ni-coated TiC particles using HIPing powder consolidation technique. The emphasis of this research was on the effect of the Ni coating on the TiC particles and the HIPing conditions on the microstructure and performance of the composites. Calorimetric effects of the mixed composite powders were investigated using the differential scanning calorimetry (DSC) technique before the HIPing process, which provided the basis of the HIPing cycles designed. The microstructures of the composites were examined using SEM with EDX. The hardness and wear resistance of the materials were evaluated respectively. It was found that the HIPing temperature influenced the microstructure and the performance of the materials. The Ni coating on the TiC particle has improved the fracture toughness of the composites, but detracted the wear resistance. The experimental results and relevant mechanisms were discussed.

Jan 1, 2004

By M. S. Ünal

Creation of 3D model of coal seams is a tedious and time consuming operation. Computer aided 3D solid modelling of coal seams can be performed in a fast and detailed manner. However, in case of having tectonically disturbed coal seams where faults may be observed, expert opinion is necessary to decide the geometry of the coal seam. The aim of this study is detection of fault zones with computers by using drill hole data. Firstly, a digital database is generated by using the drill hole data. Surface models of the layers are produced by applying triangulation method on coal seam roof elevations. The generated surface is divided into small squares and consequently dip and dip direction values are calculated for each square. Variograms for dip and dip direction are determined and maps showing the variation of dip and dip direction are generated by using geostatistical methods such as kriging and co-kriging. Examination of disconformities observed on estimation maps created by kriging and co-kriging clearly reveals the extension of faults. The method used in this study is applied to detect fault lines of a known mine field. 3D solid modelling of the coal seam has also been performed by using conventional cross-section method. The results of both methods were in good agreement. Identification of major faults by using the method introduced in this study could certainly simplify 3D solid modelling of coal seams.

Aug 1, 2013

By Etienne Roy Grégoire

Since the early 1990s, the Canadian mining industry has been increasingly defined by the signing of Impact and Benefit Agreements (IBAs) between mining companies and Aboriginal peoples. While these agreements are intended to complement the legal system, they also serve to establish the legitimacy of mining projects and to encourage the harmonious integration of these projects into their social and environmental contexts. Beyond their practical implications, what are the effects of such agreements on the ability of Aboriginal communities to access the institutional space where the authorization of mining projects and the conditions of their implementation are decided? Can we view IBAs as a preliminary step towards the operationalization of the principle of Free, Prior and Informed Consent? This paper aims to explore the potential of IBAs as a sustainable solution to the legitimacy issues that result from the implementation of the formal regulatory framework governing mining activities in this jurisdiction. We highlight what constraints and opportunities the James Bay and Northern Quebec Agreement (JBNQA) engenders for local communities and draw attention to the ways in which the negotiation of the Raglan IBA and the environmental evaluation processes act upon each other. We find that certain structural problems - and problems of legitimacy ? related to mining in Northern Quebec cannot be solved by the sole signature of an IBA, which suggests the need for caution when considering such agreements as a panacea. The Raglan case demonstrates that IBAs, like other modes of regulation relying on the direct interface between companies and communities, would benefit from a stricter framework and more explicit ties with official regulation channels.

Aug 1, 2013

By Benoît Valley

Optimization of the mining sequence in terms of economics (maximizing net present value) often leads to multi-front mining methods generating pillars. Significant resources are tied up in these pillars, but mining them is often challenging. In order to improve our understanding of rock mass behaviour while extracting these pillars, an extensive monitoring program has been designed and implemented at Vale?s Coleman mine (Sudbury, Canada). The program focuses on existing and new technologies that have potential for monitoring deformation and rock mass property changes. It includes both active and passive methods: gravimeters, multi-point borehole extensometers, fiber optic strain meters, fixed and portable three-component seismic arrays, borehole imaging and sonic logging, and, repeated LiDAR surveys. This paper reports results from an initial project phase, when only a small amount of mining has taken place. The goal was to test and compare technologies in order to assess their sensitivity, accuracy, repeatability and suitability for underground mining conditions. Value is gained by having a broad range of monitoring devices running side by side, enabling comparisons and benchmarking.

Jun 1, 2012

By J. Farrell

The Canadian government ratified the Kyoto Protocol in December 2002 and, prior to ratification, committed to equitable distribution of the burden of implementation. The Federal government's Large Final Emitters group is working with industry to develop covenants that will consider the unique nature of the company's operations and not unreasonably burden any one sector or company. Ensuring equitable distribution must consider local, national and international issues. From a Canadian iron ore producers perspective, the fact that most of the iron ore production in the world is in countries that have no Kyoto commitment is a critical issue. Another issue unique to this sector is the increased addition of fluxing agents in iron ore pellet production which has shifted some process related greenhouse gas emissions from steel producers to iron ore producers. While the objectives of the Kyoto Protocol are primarily environmental, the economic implications for Canadian industry are not trivial. For decades Canadian companies have been actively improving energy efficiency and reducing greenhouse gas emissions to maintain a global competitive position. Production of iron ore pellets is an energy intensive process and the Iron Ore Company of Canada (IOCC) is the largest Canadian producer. In 2002 IOCC identified energy and Kyoto Protocol implementation as critical risk factors for their organization and appointed a full time Energy Manager. In January 2003, IOCC initiated a comprehensive process for identifying energy cost reduction opportunities and established an Energy Master plan. This process included:

Jan 1, 2004

By Ali Hashemi, Anna P. Perry

The PQ Deeps (PQD) is a production zone located at Newmont’s Musselwhite Mine in northern Ontario. Development started for the PQD in late 2017, and the first stopes were mined starting in early 2021. Unlike most historic longitudinal stoping of narrower orebodies at Musselwhite, the PQD is a wider orebody following the plunge of a fold hinge and is extracted primarily by transverse stoping. Some geotechnical challenges were experienced during early stoping efforts, necessitating design changes throughout late 2021 and early 2022 to optimize the stope design. This work describes the mining methods and design changes to transverse PQD stoping based on geotechnical lessons learned during early stoping efforts.

Jan 1, 2023

By K. Thuro, H. Käsling, F. Menschik

"With increasing data volume, due to enhancing requirements for ground investigation programs for large construction projects, the demand for more efficient filing systems is more and more growing. Depending on the project we also have to use flexible systems to cope with varying data out of different lab and field tests.The chair for Engineering Geology at TUM is developing a web-based database solution to handle all project relevant data in a more appropriate way. We aim to optimize our data management to achieve a fast and easy way of collecting, documenting and analyzing our gained data. The second objective is to provide an easy access to our data for project partners across broadly distributed locations.This Database system consists of a PHP web interface and a MySQL database core. The current setup allows an online access via Internet (www). We are able to grant and constrain access to all data or only arrays of data with our user management system to guarantee the safety of project data and respect all rights and proprietorship. The database system is of modular design and consists of the following three base modules: module of general project data, module of laboratory data and user management module. At the current stage we are able to save and work with all usually generated specific values from unconfined compressive strength tests, brazilian tensile strength tests, point load tests, CERCHAR and LCPC abrasivity tests and ultrasonic tests. The user is able to perform a simple statistical analysis within our database (e.g. average calculation of one sample) and export data as csv or xls files for further analysis.For specific questions within projects we are able to deploy and integrate further modules in our database system. At this moment, we are developing an add on to use this database for different drill test analyses. One of the tools correlates drilling performance and drill head wear measured in the field with rock mechanical properties, and extrapolates the data to estimate the performance and wear in new projects. Today we are managing 90 projects with 550 samples and almost 1350 lab tests with the base module.In our contribution we aim to demonstrate an efficient way of data structuring using a relational database for laboratory and field testing data."

Jan 1, 2015

"Since World War II, urban communities have expanded at an unprecedented rate. The industrial mineral industry supplies the sand, grave], limestone, crushed rock, cement, gyp-sum, etc. for urbanization. Most de-posits in use are close to or within communities. Pollution of water and air has become a matter of public concern. Waste disposal and the effects of noise and vibration are subjects of public debate. Need for the reclamation of land after operations such as strip mining is discussed in magazine articles and on TV pro-grams; i.e., the general public is educated in the unattractive features of mining.Legislation is on the books and being drafted to regulate mining operations and their side effects. To avoid over-regulation and restrictive legislation, it is necessary that the public be educated and legislators informed of problems peculiar to the mining industry. Our side of the story needs publicity."

Jan 1, 1968

By Kan Xing

This paper introduces common detrimental consequences to the environment from mining in the Beijing West Mining Area. For example, ongoing mining operations can cause the following environmental deterioration: rock burst, roof rises, roof falls and inrush (Pit dash for ward water). Post-closure, after minerals resources are exhausted, the following environmental issues may remain: landslides (collapse, and mud-rock flow), dropping or exhausted water tables, water pollution, desertification and soil erosion, water accumulation, Slay endanger, ground subsidence, and causal factors in seismic activity. This paper analyzes this wide range of environmental consequences of mining, and offers a theoretical foundation to underpin a corresponding management scheme.

Aug 1, 2013

By Chas. L. Emery

"The laws of rock mechanics apply equally well to all rock structures, and open pits are not exceptions. The concepts and some arguments about the emphasis to be placed on various aspects of open-pit design are discussed in this article.RocksROCK can be described as a granular material consisting of grains and glue. The grains may be fragments of other rocks or polycrystalline aggregates. The glue may be ferruginous, calcareous, argillaceous, siliceous or other material connecting the grains. In a crystal intergrowth, the outer layers of the crystals in contact with each other may be considered to act as a glue. Water may be a glue in clay or a grain in a crystal structure. Air and other fluids or gases are grains if they occupy spaces in a granular mass. Such grains are functional either chemically or mechanically or both."

Jan 1, 1966

By J. W. Reynolds

Use of crushed waste rock recovered by sink-float separation from normal ore production for backfill is an established procedure at Commco's Sulhvan mme, Kimberley, British Columbia. Need for a safe method of placement in voids which were difficult to reach by gravity methods led to a co-operative venture with Radmark Engineering Ltd. in the development of a workable pneumatic transportation system for rock material. This paper reviews work done to date in a current program, and includes comments on the nature of the fill so placed, options for cementing such fill, implications for other aspects of mining and references to other applications of the system by other organizations who exchanged experiences with the Sullivan mine staff during the five-year period reviewed.

Jan 1, 1972

By W. P. Corking

"The purpose of this paper is to describe the relationship of the goldbearing ore to structure at the Pickle Crow mfoe. Information beyond this scope may be found in the reports and papers of Hurst( l), Bothwell(2), Thomson(3) , and Monette( 4).The property lies on Crow river, in Patricia district, 80 miles northeast of Allanwater, and about 125 miles northeast of Sioux Lookout on the Canadian National railway. From April of 1935, when the mill began operation, to the end of 1944, a total of 564,890 oz. gold and 49,275 oz. silver were recovered from 958,416 tons of ore.Mining on the property is at present carried on in two separate orebodies, the Howell and the No. 2 vein. Stoping has been carried on from every level on the Howell vein to a depth ot 2,450 feet below the surface and from several levels on the No. 2 vein through a mile long cross-cut on the 750-foot level to the Howell vein workings. A steadily increasing volume of ore is being obtained from the No. 2 vein.Each of the two orebodies consists of vein quartz with small amounts of other gangue minerals either in a single vein or a stockwork of veins. Both lie within sheared walls and carry gold in the free state. Fig. 1 shows the position of the veins with respect to the surrounding rocks. It will be noted that the delineation of the beds of iron formation shows that the lava flows and minor, interbedded sediments that make up most of the country rocks are areally folded and contorted.STRUCTURENearly all gold found to date in sufficient quantity and concentration to make ore in the Pickle Crow area is confined to these major quartz veins . Both strike a little north of east and dip north, and in both cases the attitude of the enclosing rocks is somewhat more north of east in strike and more steeply north in dip than that of the veins. As a result of this disposition both veins migrate across their enclosing rocks at a moderate angle in both dip and strike. (In this connection it should be noted that No. 2 vein dips at a considerably flatter angle than its host rock, but has a very pronounced rake to the northeast, effecting the same result as in the Howell vein.)"

Jan 1, 1954

By Scott D. Long

"Abstract-Grass roots exploration has an emphasis on good precision at low (sub-economic) concentrations of an element, in order to identify "anomalies" which may lead to drilling targets. Although it is wise to have well-defined quality controls in place during early stage sampling, the control procedures at this stage tend to be rudimentary. When a deposit warrants detailed delineation, the need for accurate geological characterization and assaying of ore-grade rock must be supported by appropriate quality control procedures.As a project returns more promising results, and the likelihood of the project warranting a prefeasibility study increases, it is time to tighten quality assurance requirements and quality control protocols. Delays in instituting adequate quality control and verification procedures may lead to costly remedial actions that can also delay completion of the prefeasibility or feasibility study. Sometimes, as a project matures, the quality control and quality assurance aspects fail to keep pace with the changing nature of the work: an increasing emphasis on precise and accurate assaying of oregrade rock.A resource model is like a house of cards. The foundation of the house is the geological observations, the sampling methods and the geological interpretations performed upon those samples. Upon the sampling, which includes all the sub-sampling steps of sample preparation, rest the assay results. The quality of the assays can be no better than the quality of the sampling. Good assaying technique will preserve all biases and imprecisions introduced during sampling and sample preparation; it cannot remove them. If the sub-samples and/or assays are bad and must be redone, all the succeeding levels of the house of cards must also be rebuilt, or at least patched up.From geological observations, a geological interpretation is built, the quality of which is critical to the construction of an acceptable resource model. Geological elements are difficult to assess, and are not discussed here; they are dependent upon the expertise of the geologists involved. Geological knowledge contributes essential quality control elements to resource/reserve determinations (Sinclair and Postolski, 1999; Postolski and Sinclair, 1999).This paper consists of five sections: (1) overview of quality control protocols, (2) maintaining quality control of databases, (3) quality control of drill sampling, (4) optimizing crushing and grinding requirements, and (5) quality control of assay data acquisition."

Jan 1, 1998

The University of New South Wales (UNSW) has been a world leader in the development of innovative virtual reality technologies over the last 10 to 15 years. These developments have included developing the world?s first 360° surround, virtual reality (VR), stereo projection theatre system known as AVIE (Advanced Visualisation and Interactive Environment), which was developed by iCinema, a collaborative venture between the UNSW Faculties of Engineering and College of Fine Arts. The UNSW School of Mining Engineering has been responsible for development of mining applications virtual reality software modules and to date, has developed eighteen different mine safety training and mining engineering education modules which run in the AVIE environment. This platform and technology package provides a unique ?immersive environment? experience for groups of trainees or students who can engage with the simulated environment in the complete safety of the virtual reality theatre. In all of the major international mining industries, safety is of paramount importance, and training of personnel is an essential component of any comprehensive proactive safety management system. All personnel need to be aware of the inevitable hazards around them at all times, as well as understand appropriate safety and operational procedures. This can be done by conventional class-room style training sessions, or by provision of training documentation. However the effectiveness of such systems is often very limited due to the inability of trainers to engage with the audience for a lengthy period of time; or to convey the often complex and variable mining environments and situations which can exist in a typical mine. The ability to immerse the trainees in a virtual mine environment, with all the reality of an actual mine but with none of the physical exposure to actual hazards, provides a far more effective and engaging training experience. Furthermore, in the virtual world, trainees can be exposed to the very unlikely, but nevertheless high consequence hazards such as mine fires, falls of ground or outbursts, without any risk to their safety and well-being. The end result is that trainees will be far more engaged with the learning environment they find themselves in, and will develop a far higher level of understanding of the topics, rather than simply experiencing a passive class-room style learning environment offered by conventional training modes. The UNSW systems have been implemented widely within the Australian mining industry and the mining engineering education sector and are now being adopted internationally. This paper presents an overview of the innovative technologies involved in these virtual reality systems ? as applied to the mining industry. Modules developed for both mineworker training and mining engineering student learning will be presented, to illustrate the effectiveness and value of such a training and education approach.

Aug 1, 2013

By F. Czerwinski

Mechanically fragmented chips of an AZ91D magnesium alloy were transformed into a semisolid slurry within the Thixomolding® system. Microstructural analysis of a material at various processing stages revealed that the cold deformation of the alloy, experienced during chipping, led to the recrystallization and growth of equiaxed grains which were subsequently converted to the globular structures by melting the grain-boundary network.

Jan 1, 2004

By C. A. Clark

The Chagres Smelter is located 80 kilometres north of Santiago - Chile, in the middle of an agricultural valley which is also one of the poorest districts in the country. This condition sets the main focus for the smelter's Corporate Social Responsibility (CSR) programmes, which ultimately aim at building self sustainable social and economic capital in accordance with the local capacities. With the help of Anglo American's SEAT (Socio Economic Assessment Toolbox), a corporately developed instrument designed to help the operations understand the needs of the communities and the impacts of those operations, the Chagres Smelter implemented several programmes, such as the CETTA (Experimental and Applied Technology Transfer Centre) programme. This project started in 2003, and consists of creating a centre for the transfer of sustainable techniques and skills for the small agricultural and livestock producers that live in the rural areas near the Chagres Smelter. Its main impacts are: Improved production quality (goat cheese and bee honey) and access to relevant markets, improved training and self-sustainability levels of producers, enhanced socio-economic level of the District's inhabitants by improving their income earning opportunities and technical knowledge, creation and promotion of a local brand as a symbol of quality products from the valley and a positive environmental impact of good breeding and native flora protection practices in the area. Other relevant social programmes are the 'Environmental Strivers', which created a recycling centre in the community; and the 'Beautiful Valley" project, which provides management knowledge and skills to local youngsters and leaders who can contribute to finding solutions for local environmental needs.

Jan 1, 2007

By G. W. Brooks

This short article is quite different to the general run of papers that are presented to the Institute, but no apology is offered because I consider that first-aid and mine-rescue work are of equal importance to many other subjects that are dealt with in our Transactions. Members of the Institute should be as much interested in the safety of persons engaged in the mining industry as they are in the practical methods of modern mining. We must not only do our best to conserve life and property by adopting every known device to that end, but we must also prepare ourselves so that we may take prompt and effective action when life is in danger, or when property is subject to loss. The need for such preparation in Alberta is perhaps greater than in most places where mining is carried on, and we must spare no effort to assemble at every mine men who are well trained in first-aid and mine-rescue work. The large area over which the mines are distributed renders central training stations out of the question, hence the need for local rescue-teams. Hospitals with skilled staffs, close enough to the mines to be convenient, also seem to be out of the question; therefore the greater need of a high standard of first-aid training for the people in our mining camps. The Government mine-rescue cars are supplied with the equipment necessary for training persons in this essential work and also for dealing with disasters should they occur. The question then arises: are there a sufficient number of men who are trained ? If so we can rest assured that what is possible to be done will be done. But if a sufficient number of trained men are not available much loss of life and damage to property is likely to result.

Jan 1, 1925

By J. B. Evans

"THE OPPORTUNITY to participate in a CIM seminarconcerning the direction of mining engineer trainingis perhaps fortuitous as it comes at a time when theengineering schools which have invited inspection byCanadian Accreditation Board of the Canadian Councilof Professional Engineers are examining theirrespective curricula.Currently there exists considerable soul-searching in various engineering schools across Canada where questions such as the following are being posed.- Have we achieved the correct balance between subjects related to technical methodology and subjects devoted to conceptual planning and design?- Should we include ""applied humanities"" in our program? (Whatever ""applied humanities"" might mean!)- Should courses covering pollution control, ecology, economics, technical writing, professional conduct and ethics be offered as compulsory subjects, as electives, or not at all?- Is it a better scheme to have students complete an Arts or Science degree before entering engineering?- Do we place too much emphasis on pure mathematics and sciences with the result that insufficient time is available for instruction in the engineering applications of these subjects?- Should English expression and/ or literature be included in the engineering programs and, if so, should these subjects be presented by the English department or by English lecturers captive to the engineering school? - Is the present program directed primarily at research activities rather than preparing engineers for their future roles in industry? - Should we teach our own versions of mathematics and physics? - Do we have sufficient engineers on the faculty strength or are we overloaded with Ph.D.'s from the pure sciences? - How flexible should the program be, what should the compulsory vs elective course content be, and what freedom of choice, if any, should be given with respect to elective courses? - To what extent should students contribute to faculty decisions?- How far should we pursue computer science subjects and do we need to make our students proficient in computer programming? - How far should operations research and mathematical models be carried in the undergraduate program when the students have limited experience in the real engineering world? - Realizing that an engineer never completes his education, should the undergraduate program cover ""bare bones"" engineering and should instruction in particular disciplines be left to graduate schools and / or industry?"

Jan 1, 1972

By A. J. Antony Chettupuzha

During a construction project, it is important to ensure that accurate and pertinent knowledge is delivered on time to appropriate personnel. The criticality of documents exchanged or referred to by various parties, evolves over the course of the project lifecycle. Determining the criticality of documents at different stages of the project can aid companies with managing the flow of information in an organized manner, while providing for the detection of potentially disruptive, erroneous material that could result in delays and costs. Therefore, it is crucial to determine documents which have the potential to disrupt a process (by virtue of being incorrect versions etc.) so that they may be isolated or prevented from entering or interfering with the active flow of information in a project, while also ensuring standard revisions of documents are recognized and accessed accordingly. Electronic Product and Process Management [EPPM] systems provide the capability to establish and map information flow between different parties in a construction project. Analyzing an EPPM system may yield information about the criticality of certain documents within an activity, as well as isolate characteristics peculiar to documents which can assist in risk mitigation. We propose methodology that identifies such critical documents.

Aug 1, 2013

By K. Stankiewicz

Projects as regards state-of-the-art mechatronic systems aiming at increase of safety in the mining industry and at improvement of coal production technologies, which have been completed at the KOMAG Institute of Mining Technology, are presented. These projects cover automation, monitoring and visualization systems, systems for implementation of artificial intelligence techniques, and database recording systems. iRIS system for electronic marking, identification, and recording of components of powered roof supports, which was implemented in 31 Polish mining enterprises, is presented as an example of the work directly associated with an increase of operational safety. Specialists from KOMAG, ELSTA, Ltd., and Silesian University of Technology in Poland, have developed flexible, configurable, and scalable system for data management, which refers to all fixed assets of mining enterprises, meeting the requirements of users as regards marking and identification of fixed assets. The system for control of roadheaders using intelligent algorithms, based on artificial intelligence techniques is also the example of innovative actions. This system aims at increasing the safety and effectiveness of teamwork due to a possibility of remote, semiautonomous operation. Introduction of artificial intelligence technology enables adaptation of roadheader mining system to the present mining-and-geological conditions. Moreover, work aiming at implementation of state-of-the-art system for control of mine jig?s beneficiation node, integrating machines and equipment in one system, is carried out as regards automation, information integration, and visualization in coal beneficiation process. Work on recovery and conversion of thermal energy, which is a by-product during operation of machines and equipment, especially mine diesel drives, is presented. Systems for energy recuperation are more and more important due to the necessity of continuous increase of power production efficiency.

Aug 1, 2013