Search Documents

By Robert M. Hopkins, Craig C. Monahan

A corrosion survey was performed on ten selected H-piles which support a reinforced concrete wharf located at Trepassey, Newfoundland. Approximately 900 thickness measurements were taken at twelve different locations in each off our zones on the steel piles: the splash (atmospheric) zone, the intertidal zone, the low tide zone and the submerged zone. Results show that over the 2o-year life of the wharf, corrosion has been most severe in the splash, low tide and submerged zones with average corrosion rates for the flanges of 6.95, 9.45 and 6.86 mils per year (mpy}, respectively, and average corrosion rates for the webs of 5.13, 4.12 and 3.45 mpy, respectively. Minimal attack was found in the intertidal zone where the average corrosion rate was only 1.66 mpy on the flanges and 1.37 mpy on the webs. Such a pattern of attack is frequently observed f or steel piles partly submerged in seawater. The abnormally low corrosion rate associated with the intertidal zone is generally explained as being due to cathodic protection induced by the high corrosion rate in the adjacent low tide zone. Analysis of the corrosion data obtained for the Trepassey wharf would suggest that this explanation might be incorrect. An alternate hypothesis has been brought forward which better accounts for the extremely low corrosion rate observed in the intertidal zones of these piles.

Jan 1, 1990

By C. H. Stockwell

RICE LAKE-BERESFORD LAKE area, situated 100 miles northeast of Winnipeg (Figure 1), is Manitoba's foremost gold mining district, although it is exceeded in gold production in the Province by the Flin Flon base-metal mining district. At present, the area is producing at the rate of about one and three-quarter million dollars annually, almost entirely from the San Antonio and Gunnar mines. The total production to date is about $14,000,000. Of this total, over $7,000,000 has come from the San Antonio mine, over $2,000,000 from the Gunnar mine, about $4,000,000 from the Central Manitoba mine, and the balance from several smaller properties. The writer has led Geological Survey parties in the area for the past four summers. The present paper gives a summary of the results of this work and also includes the findings of C. S. Lord, who was in charge of a party for one year. Much valuable information was obtained from earlier published reports on the area and from officials of mining companies, to whom the writer is indebted for their kindly co-operation. It is impossible in this short paper to give proper credit to the earlier workers or to discuss certain points o disagreement between their conclusions and those presented here. For further information the following references may be consulted.

Jan 1, 1940

By J. R. Rodda

Stainless steels are widely used to handle concentrated sulphuric acid (H2SO4) solutions produced in the manufacturing process, The majority of corrosion rate data published for stainless steel in product acid conditions is typically complied in tables or in iso-corrosion diagrams (iso-corrosion rates plotted as a function of temperature and H2SO4 concentration), without any reported consideration as to the accuracy and relevance of the method used to obtain the data, Given the characteristic potential cycling associated with the active-passive corrosion behaviour exhibited by stainless steel in hot, concentrated H2SO4, weight loss is considered to be a more reliable method than electrochemical measurements to measure corrosion rates, Consequently, an effort is made herein to demonstrate the accuracy and relevance of weight loss to determine laboratory corrosion rates in product acid conditions.

Jan 1, 2010

By Peter N. Calder, Garston Blackwell

"The history and analysis of a structurally complex open-pit rock slope displacement are described. The failure involved part of the only haulage access to a major ore zone. The ongoing movement was monitored using an electronic distance measuring device and a continuous electronic system specifically designed for the problem. A major fault, infilled with a thick clay gouge, and intersected by other structural features, resulted in the transfer of weight to a rock mass acting as a buttress in the lower regions. Movements were affected by blasting vibrations and ground-water conditions. Remedial measures included limiting blasting levels and lowering the water table, following which mining was successfully resumed in the area.IntroductionBrenda Mines is situated in a mountainous region of the southern interior of British Columbia; the location is indicated on Figure 1 . The elevation is approximately 5000 ft , giving a climate typical of more northern areas. Temperatures vary from -30°C to + 30°C. A snowfall level of 400-800 cm is experienced from November to April. During the spring, a heavy runoff period occurs, increasing the pumping rate in the pit from a nominal 50* gal/min to 2000 gal/min.The orebody occurs in a fractured Jurassic rock mass referred to as the Brenda Stock; it is approximately 3000 ft in diameter and 1000 ft deep. The Brenda Stock was intruded into the Upper Triassic Nicola Group tuffs, breccias and argillites. Mineralization occurred in several stages in a relatively homogeneous quartz diorite host rock. Shearing, faulting and jointing occured later in many stages, producing mineralized clay gouge zones up to several feet in thickness'> , These gouge zones have a major effect on the stability of the pit walls.The structural geology of the pit walls is otherwise relatively simple. Figure 2 is a conventional pole diagram indicating the orientation of the rock structural systems which are present. The major system has an average dip of approximately 70 degrees to the south and strikes approximately east /west , it is not undercu t by the pit slope. Figure 3 is a photograph of part of the North wall on which this system is indicated.The basic pit design consists of a working bench height of 50 ft, with a final wall height of 100 ft between berm s and a 100-ft-wide berm every second lift. Combined with a local face slope of 50-70 degrees, the resulting wall slope, not including haulage roads, is 45 degrees. Figures 4 and 5 are generalized plans and sectional views of the pit."

Jan 1, 1980

By Jian Deng

Rockbursts are sudden and violent failure of rocks in deep and/or high stress mines, which may destroy the excavation space and cause an accident or even the death of mining workers. This study is motivated by the pervasiveness of rockbursts all round the world. It has been found that rockbursts are often stimulated by dynamic fluctuation which is generated by mining operations or other sources of vibrations, such as blasting in adjacent stopes. This paper attempts to investigate the dynamically stimulating mechanism of pillar rockbursts in hard rock mines from an innovative point of view. Rockbursts are classified into triggered rockbursts and induced rockbursts in accordance with the magnitude of the stimulation force. Triggered rockbursts occur only when a small fraction of stress changes associated with rockbursts is accounted for by the causative excavation, whereas induced rockbursts happen where the causative factor is responsible for most of the stress changes required to produce the rockburst. By considering rockbursts as a dynamic instability problem of structures, rigorous mathematical models are set up for triggered rockbursts and induced rockbursts, respectively. By using the method of averaging and the method of eigenvalue problems, the boundaries of rockburst occurrence of a pillar are obtained for these two rockbursts. A new explanation of the failure mode of fretting or necking of pillars is given, the perturbation effect for pillar rockbursts is found, and the parametric resonance mechanism of pillar rockbursts is revealed. The quantitative relation between blasting parameters and pillar rockbursts obtained can be directly used to control the rockbursts. Contrary to conventional methods where only rock materials or rock specimen were used to study rockbursts, this investigation attaches more attention on the structural effect on rockbursts, which have strong potential applications in deep mining.

Jan 1, 2015

By John Wightman

LOCATION OF PROPERTY THE property of Caribou Gold Mines, Limited, is situated in the north-eastern part of Halifax county, seven miles south of the Canadian National railway line at Upper Musquodoboit. Approach to the village is by a secondary road, improved recently by waste rock from the mine dump. A two-wire telephone line, seven miles long, built and owned by the present operators, provides communication to the nearest telephone exchange, Parker's Corner. HISTORY In 1870, the Caribou area was recognized as a proclaimed gold district. From then on, operations were intermittent, with periods of considerable activity by small companies until there were no fewer than seven mines in a district two miles long by three-quarters of a mile wide. These were the Holman, Truro, Caffrey, MacDonald or Elk, Lake, Dixon, and Hilchey properties, all of which have had separate stamp-mills, and have produced gold for varying periods. Depths of the workings range from 100 feet to 1,000 feet. Power was generated at each property by means of steam boilers. At the present time, the Consolidated Mining and Smelting Company of Canada, Limited, controls all the leased areas, approximately 800 acres, and is operating by means of one central vertical shaft. GEOLOGY The district in and about Caribou Mines has an elevation of approximately five hundred feet above sea level. The area is fairly well wooded, with rock outcrops here and there. These outcrops, along with information from test-pits and shafts, have been the basis for the very excellent geological map of the district prepared by E. R. Faribault some years ago. The rock structure, which is one of the best examples in Nova Scotia of an elliptical dome, has its anticlinal axis in a northeast-southwest direction, and flat plunges in the same directions.

Jan 1, 1938

By Tim Gartner

This paper introduces a new application of a proven technology to provide dynamic, voltage regulation in underground mine electrical distribution systems. This technology acts to ?stiffen? the electrical power feeding continuous miners and generally raise and improve the voltage regulation at the continuous mining machines which may be located over long cable distances from the mine incoming electrical substation. This is extremely valuable for large underground continuous mining operations that use high power electrical mining machines fed over very long cable lengths (measured in 10s of km, from mine shaft to mine operating face). This new technology provides fast acting dynamic voltage regulation (voltage support) while starting continuous borers and extensible conveyor belts. Additionally, if the mine suffers from a lower distribution voltage due to long cable lengths, this new technology will raise the overall voltage at the mining machine, which can increased mining machine production and lead to longer motor life. The technology is based on voltage source converters operating as static VAR compensators specially packaged for the harsh underground mine environment. While static VAR compensator technology has been successfully used in utility and large industrial applications for many years (including open pit mining and arc furnaces), it has not (until now) been applied in underground mining. The paper will present the problem of poor voltage regulation in underground mines on weak electrical utility networks. It will then discuss some of the alternatives that have been used to resolve this voltage problem. It will then introduce the new technology used to solve the problem and review the issues involved in using this technology in the harsh underground environment. Finally, the paper will present preliminary performance results from an actual installation in a large underground continuous mining operation in Canada.

May 1, 2003

By Rodrigo Serna-Guerrero, Ted Nuorivaara

"As the demand of raw materials increases in a global scale due to demographic and economical changes, it is necessary to find technological solutions that improve current production processes in an efficient and sustainable manner. The main objective of this preliminary study is to evaluate the properties of foam produced with a cellulose-based molecule as an alterative to commercial frothing agents in flotation operations. There are two potential advantages identified with the use of cellulose-based additives for the proposed application: i) these chemicals can be produced from sustainable sources (i.e., non-edible crops), and ii) cellulose can be functionalized with chemical groups, in order to rationally modify its behaviour. In previous studies dealing with foam stabilization, it has been proposed that some functionalized cellulose species present a self-assembly mechanism at gas-liquid interfaces. Unlike typical surfactant-based frothers, cellulose molecules form networks around the bubbles that act as protective layers to the mechanical stress and to the occurrence of ionic species. This work studied the properties of foams produced in the presence of a partially hydroxylated cellulose molecule (i.e., hydroxypropyl methyl cellulose; HPMC) under various concentrations in a laboratory-scale column. A comparison with a commercial surfactant frother (i.e., Nasfroth 240) is presented, and a rationalization of the behaviour of HPMC in terms of foam properties (i.e., surface tension, bubble size, foam depth) is proposed. INTRODUCTIONThe search for green alternatives to chemicals produced from non-renewable sources has become a topic of major relevance in industry (Choi et al., 2015). As a chemical consuming industry, the mining sector faces now the challenge of adopting new processing technologies and strategies in order to achieve the future demands of sustainability. Evidently, a move towards green chemistry can only take place by identifying substitute molecules offering potential advantages in terms of recovery and grade."

Jan 1, 2016

By A. Himsley, E. Byleveld

"With reference to the chemical constraints underlying the ion exchange process for uranium recovery, a generalized view is presented on the actual and the achievable efficiency of the process. The area considered is restricted to acid leach circuits in combination with nitrate, chloride or sulphuric acid elution.A comparison between actual plant results and the chemical requirements shows that:(a) Unless new and better ion exchange resins are developed, no dramatic change in equipment size and resin inventory is""anticipated. (b) Elution efficiency, especially for sulphuric acid, may be improved considerably. More concentrated eluates may beproduced at lower chemical consumption. A possibility of achieving additional purification solely by ion exchange is discussed.IntroductionThis paper presents a generalized view of the actual and the achievable efficiency of the ion exchange processes for urannium recovery. The study is restricted to acid leach circuits in combination with nitrate, chloride or sulphuric acid elution. The ultimate efficiency attainable with ion exchange is dietacted by the chemical reactions underlying the process. The most sophisticated technology cannot change the diffusion rates in the ion exchange resin nor make the uranium loading exceed its equilibrium valueThe design of an ion exchange plant for uranium recovery involves a considerable number of parameters as a result of the wide variety of pregnant solutions produced from different orebodies. Therefore, a generalized approach of the ion exchange process inevitably neglects some parameters which maylead to significant variations in apparently identical situations.The uranium concentration in the pregnant solution, together with its pH, are the principal variables which determine resin loading and residence rime in the ion exchange system. On the elution side, the type of eluant and its concentration will determine the contact time required and the amount of eluant needed to strip the resin. The temperature, the properties of the ion exchange resin, the total dissolved solids in the feed solution and the competing ions are other variables that affect the chemical performance; these, however, may be considered as a correction of the principal parameters if one is interested only in general trends."

Jan 1, 1980

By C. O. Swanson

THE purpose of this paper is to discuss the use of the dip needle in the field of mining geology. The subject matter is new only to the extent that it reflects the writer' s added experience in recent years. The treatment is brief, and those interested in a more extended analysis are referred to the articles listed at the end of the paper. In the discovery and tracing of mineral deposits, the clip needle, like most other geophysical instruments, can be used in two ways. One method may be termed direct; the other, indirect. The direct method is that of finding or following certain ore-bodies by virtue of their magnetic properties. Explicitly, or by inference, it is the method which many mining men and practising geophysicists have in mind when they consider whether or not a certain property should be studied by geophysical means. In the ideal case, this method demands little or no knowledge of geological conditions. The indirect method uses the clip needle as an aid to purely geological studies in working out the structure of a mineralized area. Although not as simple as the direct method, it enjoys a much wider field of usefulness. The writer's experience in the past fifteen years, which is believed to be typical, is that the indirect method finds application four or five times as often as the direct method. The indirect method is of particular value because it furnishes information concerning the relationship between geological structure and ore occurrence. Most mining engineers will agree that structural control is an important factor in the localization of ore deposits, and therefore that the subject under consideration is of some interest in mining geology. Specifically, then, the present purpose is to outline the principles and practice of using the clip needle in working? out geological structure.

Jan 1, 1941

By S. Caron

From the early 70?s, ?Centre de Recherche Minérale? (CRM) has conducted and co-ordinated Research and Development activities for the mineralurgical and metallurgical industries. Since 1999, CRM has continued its mandate through COREM which is a consortium of 13 members that uses the benefits and advantages of collaborative pre-competitive industry / university research. In particular, COREM?s ?In-Situ Optimization Group? is involved in the implementation of modern optimization and control tools. The POP Project was launched in order to increase and consolidate the use of modern optimization and control tools and methods for mineralurgical and metallurgical processes. To ensure a successful transfer in the industry, there are a number of essential activities that have to be undertaken. These activities have been identified by COREM?s members and are grouped into three main modules: - R&D Module: Research and Development in universities, research centres and other partners; - Technology Transfer Module: integration of new tools and methods into the POP Software, industrial applications and technical support; - Training Module: education of new engineers in universities, continuing education of plant personnel through on-site workshops and resource networking by specific information exchange tools. This paper outlines the opportunities that led to the definition of the POP Project and describes its main modules. The main features of the POP Software are presented, the first application is described and finally, future developments are discussed.

May 1, 2001

By Gang Mei, Nengxiong Xu, Yanlin Zhang

After open-pit mining finishes, an iron mine with steeply inclined ore-bodies will generally transform to underground mining. Non-pillar sublevel caving method, with horizontal slice mining from up to down, is commonly used for mining deep ore-bodies under the open-pit bottom. As horizontal slice mining proceeds, a gradually enlarging goaf will be formed under the open-pit bottom, the rocks surrounding the handing and heading sides of the goaf will collapse continuously, and then these results in rock-mass failure with large deformation and displacement in the open-pit slope. Based on FLAC3D, a modeling approach to predict pit slope deformation and failure induced by transitioning open-pit to underground mining is proposed in this paper. This method mainly consists of three procedures of modeling, i.e., mining modeling, landslide modeling, and filling modeling, of which landslide modeling is the core of the proposed approach. In the procedures of modeling with FLAC3D, iteration non-convergence is taken as a local failure criterion of pit slope. When iteration calculation cannot converge, the sliding modeling will start by deleting some elements with large displacements, and finish until convergence. Before modeling landslide, several displacement contours of rock-masses in the pit slope are searched out, and each contour is an approximate possible sliding surface of the open-pit slope. From these contours, the most proper one is selected as the slope sliding surface by using the iteration calculation convergence and minimum element deletion as the judgment condition. Landslide modeling is then realized by removing the elements outside the slope sliding surface. Finally, to demonstrate the effectiveness, the proposed approach is used to simulate the process of open-pit to underground mining at Yanqianshan Iron Mine, and to predict the deformation and failure characteristics of open-pit slope during underground mining. The case study results show that: the prediction of the slope stability determined by using our method is consistent with that calculated by using the limit equilibrium methods.

Jan 1, 2015

By O. Espinoza Ortega, S. Song

A process scheme has been devised to improve the silver recovery and the grade of concentrates from the scavenger concentrate of a silver ore flotation circuit. Based on modal analysis studies it was found that silver sulfide minerals in the scavenger concentrate were associated as simple binary particles and finely disseminated in sulfide and non-sulfide gangues. Fine grinding of the concentrate improved the grade-recovery curve of silver to a very limited extent owing to heterocoagulation between liberated fine silver sulfides and coarse particles of gangue. This heterocoagulation phenomenon was prevented by grinding the concentrate in the presence of the dispersing reagent sodium hexametaphosphate. The silver grade-recovery curve was improved by practicing. before the conventional flotation step, a selective aggregation step for the fine silver sulfide particles using the non-polar oil kerosene, the sulthydryl collector Aerophine 3418 and conditioning the pulp under strong agitation conditions.

Jan 1, 2004

By R. Roufail

Mineral exploration is in a race to employ drilling technology that can perform the exploration and drilling investigation in a fast and inexpensive manner. After an extensive study of the available drilling technologies in the market, coiled tubing was chosen as a tool to be employed for mineral exploration due to its flexible mobility and ease of operation with a minimum number of personnel. Since coiled tubing technology is primarily used in the oil and gas industry, it was important to re-design the coiled tube rig to drill hard rocks in a fast and feasible manner. The main requirements were to drill the smallest feasible hole diameter and go as deep in the ground as possible, in the shortest reasonable time. The drilled rock particles, cuttings, are to be collected and analysed at the surface for their metal mineral contents. The process also needs to be repeated multiple times at different locations for mapping, without the need to change the tube on the rig due to failure or potential failure. The focus of the new designed coiled tube, for drilling and mineral exploration, is three fold. First is to increase the rate of penetration in drilling by designing a small high speed turbo motor. Second is to determine the controlling parameters of cuttings transport to effectively lift the cuttings to the surface for analysis and third is to minimize the overall weight of the rig for manoeuvring and prolong the life span of the coiled tube string. In this paper, a small downhole turbo motor, 5cm outer diameter, is designed to achieve a rotation speed of up to 10,000 rpm to fit on a small bit, coiled tube drilling assembly. The motor design utilised multiple finite volume and finite element analysis softwares for fluid flow study and fluid structural interaction analysis. The paper is also introducing the concept of a flow slurry loop that is designed to lift the cutting particles to the surface for mineralisation analysis. The controlling parameters of the cuttings transportation are the particle?s physical properties such as size, density, concentration and shape, as well as the rheological properties of the carrying fluid, drilled hole angle, as well as the fluid flow rate and flow dynamics within the annulus gap between the coiled tube and drilled hole. Such parameters are addressed via experimental work as well as numerical analysis. The paper is also presenting the selection and testing procedure of the material type for the coiled tube string. The tube needs to be light in weight for overall rig weight and its transportability. The tube is also required to drill several dozens of investigation holes before failing due to fatigue. A fatigue bending machine is designed to test the endurance limit of candidate materials for coiled tube strings and a performance index methodology is followed for material selection of the optimum material. The coiled tube rig is designed to be light in weight for transportation and relocation. It is also required to speed the drilling operation with the minimum footprint and reclaim the drilled rock particles for mineral composition analysis at the surface.

Aug 1, 2013

By M. Hajian Heidary

In this investigation, effect of pressure depth on the globulizations of AZ91 magnesium alloy was studied. Cylindrical samples of AZ91 alloy with 1 cm and 2cm in height and 2.5cm in diameter (H/D = 0.4 and 0.8) were prepared, then the samples were hot pressed at 10 and 30% strain at a constant temperature of 200°C; subsequently reheated at 555°C in different times. Results obtained from optical microscopy (OM) showed that the thickness of the samples and consequently, depth of strain affected regions have remarkable effect on the degree of globulization. In addition, it was found that at a constant strain and holding time, structure of thinner samples is more globular than thicker ones.

Jan 1, 2007

By Michael L. Free, Zongliang Zhang, Joshua M. Werner

In the copper electrowinning process, short-circuiting between the anodes and the cathodes is a critical problem that changes the current allocation among local electrodes and reduces the current efficiency significantly. Possible reasons for the short-circuiting include the improper alignment of the electrode, bent electrode, and nodules on the cathode surface. In typical tankhouses, there is often a time between shorting and harvesting as well as between shorting and clearing. Therefore, it is inevitable to have short-circuiting affect the operation performance in practical electrowinning operations. However, one key piece of missing data is the actual measurements of the current efficiency as short-circuiting is approached and allowed to continue. Consequently, short-circuiting tests that allow tracking of electrowinning parameters before and after short-circuiting were performed in a laboratory scale Cu electrowinning cell. In the tests, the electrode spacing change, the mass of electrodeposited Cu, the deposition morphology, and the current allocation as well as the current efficiency before and after short-circuiting were studied. Results show that the short- circuiting affects the current allocation and the current efficiency significantly. Moreover, it changes the Cu deposition on the short-circuited cathode and therefore causes problems for Cu electrowinning. INTRODUCTION Electrowinning (EW) is commonly used for copper production around the world, with a rated production from 120,000 to 200,000 tons per year per operation (Wiechmann, Aqueveque, Henríquez, Muñoz, & Morales, 2014). In Cu electrowinning, Cu ions in the electrolyte are reduced on the cathode surface as metallic copper with a DC current, while on the anode, a counter anodic reaction occurs with oxygen gas generation (Werner, Zeng, Free, Zhang, & Cho, 2018; Zhang, Werner, & Free, 2018; Zhang, Werner, & Free, 2018). In copper electrowinning, an average current density of 200 to 400 A/m2 is applied to the electrowinning cell (Wiechmann et al., 2014). As the Cu deposits on the cathode, the distance between anode and cathode reduces and most of the time, short-circuiting forms between some anodes and cathodes in a large tankhouse containing thousands of electrodes, reducing the current efficiency and increasing the energy consumption significantly. The current efficiency in well-run copper EW operations is typically above 90 %. Most of the unused current is wasted through short circuits, stray currents, and by-byproduct formation (Davenport, King, Schlesinger, & Biswas, 2002; Wiechmann, Vidal, Pagliero, & Gonzalez, 2002; Wiechmann, Morales, & Aqueveque, 2010). Usually, in the tankhouse, the short-circuiting increases the current in the involved cathode by up to 1500 A (Wiechmann et al., 2010). Multiple reasons can cause the short-circuiting in the cell, and the most common reasons include the uneven current distribution among cathodes, tilted electrodes, bent electrodes, and nodules formed due to the large deposition roughness. Recognition of this challenge in the Cu electrowinning process has led researchers to perform many investigations on approaches to avoid and reduce the short-circuiting in the cell. A series of research investigations have been conducted to develop and improve a new type of intercell bar for Cu electrowinning (Wiechmann et al., 2002; Wiechmann, Morales, Aqueveque, & Burgos, 2007; Wiechmann, Morales, & Aqueveque, 2009; Wiechmann et al., 2010; Wiechmann et al., 2014). The associated test results show that this new design limits the occurrence and magnitude of short circuits and allows operation at higher current densities. Sandoval, Clayton, Dominguez, Unger, and Robinson (2010) stated several keys to control short circuits, such as maintaining the straightness of the cathode, removing “edge hair” from the cathode starter, and maintaining electrode alignment in the cell. Prengaman and Siegmund (1999) from RSR technologies developed a new Pb-Ca-Sn anode to prevent the anode deformation, thereby reducing the short-circuiting in the Cu electrowinning cell. Although the negative effects of short-circuiting on the Cu electrowinning have been recognized, and various investigations have been conducted to address this issue, the actual measurements of the electrowinning behavior and performance as short-circuiting is approached and allowed to continue are seldom reported. However, in typical tankhouses, there is a time between when shorting occurs and harvesting/clearing are performed. One key factor in determining the harvest time is the frequency of shorting. Consequently, we have performed short-circuiting tests that allow us to track electrowinning parameters before and after short-circuiting.

Jan 1, 2019

By P. K. Kaiser, S. Maloney, S. Yazici

"This paper focusses on the strength or capacity of cable bolts and introduces a new perspective for cable bolt design by demonstrating that mining-induced stress changes may affect cables in a detrimental manner. The concept underlying a novel cable bolt pull-out resistanceor bond capacity model is described and its practical significance is demonstrated by application to a simple two dimensional scenario of a fall-of-ground.A number of practical implications emerging from the application of this model are discussed to provide guidance to ground control personnel jar improving cable bolt support systems in mining applications. These include cable layout optimization, use of cable pre-reinforcements, assessment of embedment length requirements, need for plated cables (or straps), use of bird-caged cables (or buttons), and grout quality issues.IntroductionDuring the last decade, cable bolting has become a standard support technique in mining for handling wide spans, reinforcing are passes, preventing or reducing dilution of ore in marginally stable stopes, and for many other rock support need s.In its infancy, many deficiencies in cable bolt supports resulted from improper installation techniques and, in particular, grout quality control problems and the use of empty breather tubes (Goris, 1990). The development of special grout pumps and fail proof placement procedures (Oliver, 1992; Bourchier and O'Flaherty, 1992) have eliminated many of these early problems. Nevertheless, there are still situations where cables seem to lose their capacity during mining, and in these cases the cables do not provide the expected and needed ground support. In some instances, cables perform extremely well, whereas in others the same support layout and quality of support installation seem to be insufficient, allowing falls-of-ground or progressive cavings to occur."

Jan 1, 1992

By K. Forsberg, A. Rasmuson, R. Rodriguez Varela, J. Martinez De La Cruz

"This study analyzes the separation of rare earth elements by means of a supported liquid membrane (SLM) with the final objective of recovering REE from an apatite concentrate (Alemrajabi, Forsberg, & Rasmuson, 2015; Mohammadi, Forsberg, Martinez de la Cruz, & Rasmuson, 2015). In this study, the feed phase consists of an aqueous phase containing REE, the membrane phase contains the organic solvent and carrier (D2EHPA and EHEHPA), and the stripping phase is a hydrochloric acid solution. An evaluation of mass fluxes, separation efficiency, and membrane performance is conducted. In order to analyze the suitability of liquid membranes in the extraction of REE, a deeper insight into the mechanisms causing instability is needed. In this study, surface tension is considered as the key factor of Marangoni instabilities and spontaneous emulsification.INTRODUCTIONThe demand of REE and their compounds has increased considerably due to their special physicochemical features that make them crucial elements for numerous high-tech applications, including wind turbines, hybrid cars, mobile phones, and defense technologies. They are also extensively utilized in traditional industries such as nuclear energy, petroleum, metallurgy, agriculture, and textiles (Xie, Zhang, Dreisinger, & Dyole, 2014; Zhang, Wu, Bian, & Zeng, 2014).Solvent extraction is widely used for the separation of REE (Xie et al., 2014; Zhao, Huo, Pan, Li, & Liu, 2014). Di-(2-ethylhexyl)-phosphoric acid (D2EHPA) and 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester (EHEHPA) are two of the most effective extractants for the separation of rare earth elements among organophosphorus extractants (Gupta & Krishnamurthy, 2005). However, the difficulty in stripping loaded D2EHPA extractant, especially for heavy REE, has limited its utilization. Yttrium can be stripped at lower acidities in EHEHPA systems compared to D2EHPA systems (Gupta et al., 2005), but the extraction efficiency is lower. Conventional solvent extraction by mixer-settlers is restricted by its large solvent inventory and loading limits, and suffers from phase disengagement, emulsification, loss of solvent, and flooding problems (Swain, Jeong, Lee, & Lee, 2007). In this context, supported liquid membranes (SLMs) present a potential alternative due to their advantages, being low solvent inventory, process simplicity, low energy and operational costs, great enrichment ratio, and combination of extraction and stripping into one single step. A SLM is a system in which two aqueous phases are separated by an organic liquid membrane suspended in the pores of a porous support by capillary forces. One of the aqueous phases is the feed solution with the solute and the other is the stripping or receiving solution. The solute diffuses through the liquid membrane and then is extracted into the stripping solution (Kislik, 2010)."

Jan 1, 2016

By D. Chakravarty, B. Samanta, D. Ghosh

Autonomous robots are useful for 3D underground mine mapping to avoid human exposure to hazardous spaces. To prepare a precise mine map, a self-navigating robot must navigate an arduous path, avoiding obstacles and sensing the environment. A prototype laboratory-scale robot was built and evaluated through a mock-up in a test mine gallery. It was outfitted with a 2D laser scanner, a stereo camera for obstacle avoidance, and a high-precision, laser-based imaging and digitizing system for collecting 3D point cloud data. Various algorithms were used for scan matching to facilitate simultaneous localization of the robot for mapping.

Jan 1, 2014

By Russell F. Palmer

"THE PRACTISING MINING ENGINEER has little time for the expression of opinion on abstract questions concerning the definition and future of mining engineering. The following comments indicate some of the thoughts and suggestions of those who have found mining engineering a very satisfying field of endeavour. The future of mining engineering has been under discussion for perhaps twenty years. It is significant that the University of Saskatchewan program was in- 88 traduced at the time that some traditional mining schools were questioning the need for mining engineers. One Canadian university, and some American schools, actually abandoned the field at this time, some ten years ago.Five years ago, Mining Magazine sponsored an international debate on training for the future, and concurrently, the CIM undertook a major survey of the mineral industry's manpower needs. The current CIM discussions should prove more fruitful, as they are directed toward mining engineering alone, rather than the broad, and confusing, spectrum of all professionals and semi-professionals of the mineral industry."

Jan 1, 1972