Search Documents

By Lewis Martin

Whereas many researchers and mine engineers have conducted tests using different types of grout, grout ratios, and physical modifications of the cable to determine cable bolt load characteristics, few studies have been conducted on cables fitted with internal instruments. Those studies that have been done have concentrated on cable behavior averaged over significant cable lengths. Researchers at the Spokane Research Laboratory (SRL) of the National Institute for Occupational Safety and Health in Spokane, WA, are investigating the physical properties of cable bolts by replacing the conventional king wire with a modified king wire on which strain gauges have been installed . This paper documents test results on these modified cable bolts. Three tests were conducted at SRL on 1.83-m-long cables grouted into two 0.91-m-long pull-tube assemblies. Load along the cable was monitored with 20 strain gauges installed along the length of the cable. The instrumented cable bolt provided reproducible point measurements of cable load as opposed to load measurements averaged over significant cable lengths. Such point measurements can assist in interpreting the influence of cable confinement, grout quality, rock mass stiffness, and other factors. The instrumented cable bolt is a practical field and research tool because it can predict point loading along the cable and thereby allow interpolation of maximum possible loads on a cable.

May 1, 2002

By K. Meyer, M. E. Goddfellow

"At Teck-Corona Operating Corporation's David Bell Mine, a water quality management strategy is employed to produce both a chemically and biologically clean effluent prior to discharge to the environment.The strategy includes operating methods to minimize contaminants leaving the concentrator and an effluent treatment plant for cyanide, antimony, and heavy metal removal of concentrator, mine and site waste streams.Concentrator practices, the effluent treatment plant, process chemistry and the present day performance of the water quality management strategy are reviewed.INTRODUCTIONThe David Bell Mine is located in the Hernia gold camp 35 km east of Marathon, Ontario. The concentrator has a design throughput of 1,000 tonnes per day. ROM ore (-6"") is ground in a semi-autogenous mill followed by a ball mill, thickener, leaching, and carbon-in-pulp gold recovery unit operations. The concentrator flow sheet is shown in Figure 1."

Jan 1, 1991

By S. S. Teal, W. W. Weber

"AS THE TITLE implies, this paper will deal with the unusual rather than the standard practices as employed . at the property of North Rankin Nickel Mines, Limited. Fortunately •the mining, with the exception of permafrost conditions, and the milling practices, are the normal approaches dictated by the size, type, and character of the orebody. The unusual aspects are linked directly or indirectly to the isolated location and are •principally ancillary requirements or services covering a broad range from climate to supplies and from finance to entertainment. It is our intent to cover the more salient points of interest together with a brief description of the general operation.To understand the primary motivation of the mine, it must be made clear that North Rankin was conceived as a foothold in the Canadian North, that region embracing 40 per cent of the Dominion which ex-tends north of the commercial tree-line and which includes nearly 50 per cent of the Precambrian Shield, our mainstay of Canadian mining. Secondly, this project was born in an atmosphere of premium sales in the nickel markets, assuring a rapid pay-back of the heavy •capital expenditures. And finally, it has •been coddled through the stark reality of a competitive metal market with the hope and trust that the experiences and achievements will lead over the bill to a bigger and better mine in this virgin territory. This is the briefest story of the mine's history, but it pays tribute to the many people who, in thirty years since .discovery, have championed this project."

Jan 1, 1959

By Rob Boom, Yasuyuki Tozaki, Greg Traquair

The objectives of the business case are to examine a proposed metallurgical project and answer fundamental questions about project feasibility, risks, opportunities, and value. A business case fulfills these basic functions: estimates economic value; helps to understand competitiveness; serves as a risk management tool; and serves as a communication tool. A business case evolves with the project life cycle, and supports the gate reviews at the end of each phase of engineering, through to project construction and operations. A business case must be holistic, including all elements of scope that can impinge on project risk and value.

Jan 1, 2015

By A. R. Sorta, D. C. Sego

ABSTRACT Temperature, solute, texture, and thixotropic effects on time domain reflectometry (TDR) measurements of water content in oil sands tailings are investigated. Results indicate that TDR water content measurements are influenced by temperature, residual bitumen, and percent clay in the tailings. A correction of 0.03–0.10/ °C must be applied to the apparent dielectric constant (Ka) to account for the effect of temperature. The Ka-volumetric water content relationships of slurries differ significantly from the commonly used Topp calibration equation. The age of the tailings and the addition of phosphogypsum did not influence TDR water content measurements.

Jan 1, 2013

By C. J. Farrow, M. J. Smith

"Bechtel has managed a number of test programs to establish autogenous grinding circuits and size mills for a variety of ores.This paper outlines the procedures whereby bench scale and pilot plant tests are used to select the most efficient circuit to grind the range of ore types likely in the mill feed.Five examples are given. One example traces the development of a pilot plant program; it shows how bench scale Work Indices provide a target for the grinding power requirement of an ore and relates how pilot circuits are changed as a result of interpreting the results from preceding tests. The other four examples relate the interpretation of the test results to provide design data; they illustrate a number of phenomena which have been observed.INTRODUCTIONConventional crushing and grinding circuits can be specified from bench scale test data such as Bond Work Indices. Bond Indices have been correlated to a large number of rod and ball mills and by applying appropriate factors, mills can be sized from the Work Index.For autogenous or semi-autogenous grinding circuits, bench scale tests are not sufficient to be able to specify the circuit and size of the mills for a commercial plant. It is necessary to run a series of pilot plant tests to determine how the ore behaves."

Jan 1, 1982

? Founded In 1953 ? Mining growth of 83% since 2007 ? We produced over 1 million ounces of Au in 2012 ? We Forecast of 20% Au production in 2013-2015 ? We have paid a dividend 31 years consecutively. Terry Reid ? 1992-93 Electrical Technical, College ? 1994-95 On the job placement College ? 1998 ? Licensed Millwright, ? 2005-12 ? Maintenance Reliability Planner ? 2012- Present Business Process Owner

Aug 1, 2013

By R. D. Brown

The Federal Government's White Paper on Tax Reform received further major criticism in the reports of the Committees of the House of Commons and the Senate, which recently completed a lengthy review including public hearings of the government's proposals. These reports both criticized the emphasis placed by the White Paper on its concept of tax equity rather than on a system which would promote economic growth. However, the Finance Committee of the House of Commons was prepared to accept, with modifications, a number of the White Paper's key reform proposals. The Senate Finance Committee was more critical of the basic thrust of the tax reform program and recommended that a modification of the existing tax system would be more appropriate to Canada's needs. Both Committees re-commended a more favourable treatment of mining income than that originally proposed in the White Paper, and to some extent both Committees suggested proposals that were even more favourable to the industry than those set out in Finance Minister Benson's amended proposals made in August of this year. This article out-lines the principal recommendations and comments in the reports of both the House of Commons Committee and the Senate Finance Committee.

Jan 1, 1971

By E. R. Hughes

Introduction Situated 182 miles east of Vancouver, on the Kettle Valley branch of the Canadian Pacific railway, the Princeton coal field is readily accessible to the Coast markets. The area covers approximately forty square miles and present indications are that the deposits should contain at least 300,000,000 tons of coal. Comparatively little development has yet taken place in this coal field. Since the commencement of recorded output, the collieries operating in this area have produced 1,640,518 tons of coal. The coal field proper includes only the Tertiary deposits adjacent to the town of Princeton and does not include the Coalmont or Nicola deposits. Production has never been on a large scale. The largest annual output from any property was 81, 780 long tons mined at the Granby colliery in 1940. Coal output was first recorded in 1909 and since that time fifteen properties are reported to have either mined coal or to have done prospecting or development work; of these, only two are presently active. However, none of the properties now inactive were closed because their coal resources were exhausted. The accompanying key map shows the extent of the Princeton coal field, and the location of the coal mines and prospects in this field General Geology The Princeton field is underlain by rocks of Oligocene age and is one of the series of more or less isolated Tertiary lake basins in which coal, or lignite, has been found in the interior of British Columbia. Resting on the Nicola group rocks of Triassic age, the Princeton sedimentaries consist of sandstones, conglomerates, shales, bentonite, bentonitic clays, and several seams of coal. Tertiary volcanics occur both above and below the stratified rocks and in places they have been thrust through the overlying measures. In some areas, the coal has been burned to a red ash as the result of vulcanism, while in other parts some of the moisture has been driven from the coal, thus improving the grade. The field can best be described by dividing it into two areas: the Southern area, lying to the south of the town of Princeton, where most of the mining has been done; and the Northern area, to the north of Princeton, where very little development has taken place.

Jan 1, 1947

By E. H. Dudgeon

In order to make increased use of automation in copper smelting, it is evident that a useful first step .world be the accurate determination of the copper end point in the converter operation. After laboratory tests, the copper end points in a copper converter at Gaspe Copper Mmes Ltd. were determined without reference to melt samples or other observations. The results indicated that the rapid measurement of the S02 level in the gas released from the converter has potential as a new and independent method of determining the copper end point in converter operation.

Jan 1, 1966

By E. J. Sides

In this paper, the argument is put forth that the codes used for public reporting of mineral resources and mineral reserves have some significant limitations with regard to the information provided to investors on the short- to medium-term value of mining properties. Such limitations include a) failure to explicitly incorporate a time element and b) failure to state explicitly the quantity and quality of mineral product that will be produced for sale. A time-value framework for reporting mineral assets is proposed in order to overcome these limitations. The proposed system is based on two classification axes: a) an X-axis representing time in years during which the value of the asset is likely to be realized and b) a Y-axis representing the value identified by a mining or exploration company\u2019s activities. The potential benefits of this system are discussed, including the ability to incorporate factors, such as permitting and construction times, directly into the magnitude of the reported mineral assets. The proposed framework would assist in the standardization of mineral assets reporting in such a manner that they could eventually be more readily included in financial statements. Year of Publication: Not explicitly mentioned in the document.

Jan 1, 2010

By K. Leung, J. E. Udd, L. B. Geller, F. Kitzinger

"Sixteen miners died tragically at the Paymaster gold mine in Timmins, Ontario, in February 1945 when a badly corroded hoist rope broke. The investigation of the Royal Commission that followed arrived at a number of recommendations (The Legislative Assembly of Ontario, 1947) aimed at avoiding future disasters of this kind. One consequence was the development and legislated use in Canada, several decades ago, of powerful electromagnetic (EM) instruments for the non-destructive testing of mine shaft wire ropes. The authors have been involved for many years in the design, production, and testing of EM instruments (Geller and Udd, 1990, 1992; Geller and Kitzinger, 1991; Geller et al., 1992). Since the mid-1990s, particular attention was paid to the design and operational results obtained from the computer controlled portable MagnographTM II wire rope tester (Geller et al., 1995, 1998).In the present paper, the authors summarize further hardware- and software-related developments of this instrument. Further, an account is given of the results obtained from the most recent design known as the Perma- ScanTM testing system. This is also a computerized dual-function system. In it, however, the sensor head is designed primarily, if not solely, for permanent installation and for remotely controlled operation. This represents a basic departure from traditional designs, which were intended for ad hoc temporary installations. The remote-controlled instrument described in this paper has now been in operational use for more than four years."

Jan 1, 2003

"The Upper Mannville unit commonly consists of interbedded marine and non-marine sands and shales, but in northwestern Alberta the unit consists of marine shales of the Spirit River Formation. A thick tongue of marine shale (Clearwater Formation) ex-tends eastward into the Athabasca area below sandy Grand Rapids beds. Correlation of Upper Mannville rocks to the southeast is difficult, but in the Cold Lake area a thick sandy depositional cycle (Mannville ""C"" of this paper) appears to be approximately correlative with the Clearwater Formation. In the Lloyd-minster region, tongues of marine sedimentary rock occur in the lower part of the Upper Mannville unit. Most of the Upper Mannville oil occurs in the Grand Rapids Formation at Wabasca, in the thick ""C"" unit and younger Mannville sands at Cold Lake, and in the Sparky and General Petroleums sands of the Lloydminster region (Figure 2).The Lower Mannville unit was deposited on an erosional surface of considerable relief that truncated the Jurassic and older strata of the Western Canada basin. Continental, probably fluviatile, sedimentation persisted over much of the Western Canada basin during deposition of the Lower Mannville unit, but an Arctic or Boreal sea lay over part of northern Alberta. At the end of the depositional episode, the sea transgressed southward and eastward (Figure 3) and re-worked the Bullhead and McMurray sands of northern Alberta into the glauconitic Bluesky and Wabiskaw sands. Topography on the sub-Cretaceous erosion-al surface had a considerable effect on the deposition of the Lower Mannville (Rudkin, 1965), and the highest hills on this surface were not completely on-lapped by Lower Mannville sediments (Figure 3). The coarser elastic material was derived both from a western Cordilleran region and from an eastern Canadian Shield region (Glaister, 1959, p. 620; Mellon, 1956)."

Jan 1, 1966

By Ronald L. Bruening

IBC has developed a cost effective MRT process for the selective extraction and recovery of gold, copper, and a mixture of other base metals from mine leach cyanide solutions. This is a two-stage system in which the gold is first recovered selectively as a high purity salt. The copper is then recovered separately as a sulfate salt. The other base metals are then collected as a cyano anion concentrate. Three different SuperLig® materials are used. The first stage can be used alone on gold leach solutions where copper and other base metals are not a problem. The two or three stage system is used when the base metals build up in the leach solution, resulting in increased costs. The cyanide or cyanide/cyano anion concentrate can be recycled back to the leach solution until the build-up of other salts, etc. becomes too high, or this too can be controlled with a percentage bleed stream.

Oct 1, 2003

By Peter Claus

In the last years, supported gold catalysts with particle sizes smaller than 10 nm have attracted a lot of attention. While gold bulk metal is rather inert in chemical reactions and, thus, is of low interest for catalysis, highly dispersed gold particles supported on oxides as TiO2 or ZrO2 show surprisingly high activities in some reactions important for the chemical industry. The oxidation of carbon monoxide at low temperatures is mainly used as model reaction to study the unusual properties of gold catalysts [1]. On the other hand, to evaluate the catalytic potential of gold, other chemical reactions which allow to control also the selectivity have to be considered. The selective hydrogenation of ???-unsaturated aldehydes to allylic alcohols is of both commercial relevance (e.g. in fine chemical and pharmaceutical intermediate production) and specific scientific interest [2]. Note that thermodynamics favors hydrogenation of the C=C over the C=O group (stronger negative free reaction enthalpy of 35 kJ/mol), and for kinetic reasons the C=C bond is more reactive than the C=O group. Thus, in the presence of most of the conventional hydrogenation catalysts, based on Pt, Rh or Pd, -unsaturated aldehydes such as acrolein and crotonaldehyde are hydrogenated predominantly to the saturated aldehydes and only to a minor extent to unsaturated alcohols. Therefore, it is desirable to find catalysts which are able to control the intramolecular selectivity by hydrogenation preferentially the C=O group while keeping the olefinic double bond intact (Fig. 1).

Oct 1, 2003

By R. A. Wyman, F. E. Hanes

THE demand for high-quality aggregate is increasing in all phases of the construction industry and in all organizations associated with road building in Canada. The production of aggregate in Canada has increased almost continuously since the end of the war and has quadrupled since 1948. Increases during the past fifteen years can be accounted for by the expansion in all types of construction, particularly that of roads and highways. Total construction in 1959, based on preliminary estimates, has been valued at $7 billion, and an increase fore-cast for 1960 indicates optimism on the •construction horizon (1). Cement produced in Canada in 1959 amounted to 6.3 million tons. This is more than 2.5 times the 1948 production. Increased cement production indicates an increased use of concrete, and thus an increased need for aggregate. Natural sand and gravel deposits are gradually being depleted.

Jan 1, 1962

By William Winsor, Harold L. Snyder

"AbstractShould oil and gas be proven in commercial quantities on the Labrador Shelf, current technology is not adequate for production operations in this severe environment, which includes yearly invasion of pack ice and icebergs. The fishery of this section of the North Atlantic is a vital resource to which a major oil spill or blow-out would impose an intolerable burden, This means that production systems must be designed and built to be fail-safe.The experiences of mining in Bell Island and Cape Breton have shown that it is possible to operate beneath the ocean floor, and this technology may hold the key for safe, reliable and economic production, This paper attempts to define particular problems and outline possible solutions.IntroductionOUR DISCUSSION is subject to the assumption that large hydrocarbon reservoirs will be discovered in the sedimentary basin of the Labrador continental margin. The petroleum industry has not attempted to operate in a harsher area. The Labrador coastline is exposed to North Atlantic storms and icebergs year’round, Arctic pack ice occurs up to six months of each year. However, there is no doubt that, if sufficient hydrocarbon potential is outlined, development will proceed."

Jan 1, 1977

By D. Allan Coutts

Demonstration projects using hydrogen as a fuel are becoming very common. Often these projects rely on project-specific risk evaluations to support project safety decisions. This is necessary because regulations, codes, and standards (hereafter referred to as standards) are just being developed. This paper will review some of the approaches being used in these evolving standards, and techniques which demonstration projects can implement to bridge the gap between current requirements and stakeholder desires. Many of the evolving standards for hydrogen-fuel use performance-based language, which establishes minimum performance and safety objectives, as compared with prescriptive-based language that prescribes specific design solutions. This is being done for several reasons including: (1) concern that establishing specific design solutions too early will stifle invention, (2) sparse performance data necessary to support selection of design approaches, and (3) a risk-adverse public which is unwilling to accept losses that were incurred in developing previous prescriptive design standards. The evolving standards often contain words such as: ?The manufacturer shall implement the measures and provide the information necessary to minimize the risk of endangering a person?s safety or health.? This typically implies that the manufacturer or project manager must produce and document an acceptable level of risk. If accomplished using comprehensive and systematic process the demonstration project risk assessment can ease the transition to widespread commercialization. An approach to adequately evaluate and document the safety risk will be presented.

May 1, 2007

By Rob Boom, Yasuyuki Tozaki, Frank M. Wheeler

Selection of a suitable site for a metallurgical plant is crucial for the success of the business case. For a brownfield project, with the decision to locate the project on a site with existing production facilities and activities, the selection of the site has been made. For a greenfield project, important economic and logistical considerations include proximity to primary and secondary resources and/or to the market, infrastructure, and access to energy and water. National and regional aspects, including the social license to operate, can be decisive in final site selection. Key to recruiting and retaining a labour force are proximity to urban areas, along with weather and health conditions at the site. Risk factors include site geotechnical parameters and topography, contamination, as well as probability and types of potential natural disasters.

Jan 1, 2015

"The Hardy Cross algorithm offers a reliable method of solving network systems of fluid flow and has become widely used for solving water and ventilation flow networks. A limitation is that computational iterations and time to solve a network rises rapidly with the size of the model and modern detailed ventilation networks have typically grown to thousands of airways. Non-linear matrix solving methods can offer improved performance, however these are more complex and may be unstable if initial estimates are poor. This paper presents improvements that can be applied to the traditional Hardy Cross algorithm to greatly reduce iterations and solving time for large ventilation models. INTRODUCTION The Hardy Cross algorithm (Cross, 1936), was originally developed to solve water flow in city and urban pipe networks. Using principles of Kirchhoff’s electricity current laws, Hardy Cross developed an iterative algorithm for solving non-linear equations associated with network water flow. Traditional network analysis research refers to the various members of system networks as branches, nodes and meshes. This terminology has been changed in this paper to airways, junctions and loops respectively which are terms more familiar to engineers in mine ventilation. When Kirchhoff’s laws are applied to fluid networks, the following assumptions can be made: •The sum of fluid flows into a junction must equal the sum of fluid flows out of the junction.•The sum of pressure losses around any loop through a network system must be equal to zero.An iterative solution can therefore be achieved by initially guessing flow in a network, calculatingthe pressure losses around the network loops (Figure 1), and applying flow corrections using Newton’s method for each loop if the sum of the pressure losses does not equal zero. To solve the system, a loop must be defined for every segment or series of segments between a junction of 3 or more airways.The Hardy Cross algorithm has been used extensively for ventilation network analysis since the introduction of the first electronic computers (Tien, 1997), however numerous other variations and methods have since been developed through the use of matrices to solve the required system of nonlinear equations. Commonly used algorithms such as the Newton Raphson method (Brown, 1969), the Gradient method (Todini & Pilati, 1988), the Linear Theory method (Gupta & Prasad, 2000), and Coupled Network Solver (G. Danko, 2008) have found general use in fluid flow network solvers (Rossman, 2000). Despite poor and sometimes unpredictable convergence performance however, the Hardy Cross algorithm still has unique properties that make it attractive for ventilation models. Some benefits are:"

Jan 1, 2019