Search Documents

By H. G. Stephenson, C. W. Gregory

"This article describes the methods used for pillar extraction in the Wilson Seam at Canmore Mines, Alberta. The Wilson Seam is extremely gassy and varies in thickness between 7 and 30 ft, with an average of 12 ft. The gradient varies from 5 to 30 degrees, with an average of 15 degrees. The seam was developed using Lee Norse miners to form pillars which the company intended to extract using the same machines. Before pillar extraction commenced, an abandoned and inaccessible mine 160 ft above the Wilson had to be drained of 360 million gallons of water. When this was done pillar extraction commenced. Conditions in the mine slowly deteriorated and after 6 months the decision to withdraw the continuous miners was taken. Slusher hoists were installed to replace the continuous miners, with the result that roof conditions and safety steadily improved."

Jan 1, 1972

By C K. Bell, L. S. Collett

An AFMAG survey was flown in 1968 over the Upper Nelson River area, Manitoba. The flight direction was northwest-southeast and flight spacing was 2 miles. In the Cross Lake Subprovince, AFMAG showed that an isolated peridotite outcrop was part of a dike that extended over 80 miles. Diabase dikes are not always marked by an anomaly, but isolated cross-overs, when used in conjunction with geological and magnetic data, permit their extrapolation. Anomalies coincide with areas of sulphide mineralization. In the Flin Fion Subprovince, known and unknown northeast-trending faults are detected. The Berry Creek fault was extended south through Tramping lake, then under the Paleozoic cover. Conductors were detected at, or near, the axes of major synclines within Amisk and Snow Group sediments. Granitic terranes have low conductivity and, because they are characterized by smooth AFMAG profiles, they can be delimited. AF.MAG is being recognized as a geophysical method that can aid geological mapping and interpretation. Its most important contribution to the geologist will be in regions where out-crops are sparse.

Jan 1, 1971

By Carl Bertrand, Patrice Nadeau, Claude Bazin

"Rio Tinto Fer et Titane processes the ore extracted from the Lac Tio orebody to concentrate the hemo-ilmenite (FeO.TiO2-Fe2O3) mineral that is subsequently smelted to produce pig iron and titanium oxide slag. The ore is crushed, heat treated (roasted) and concentrated using dry magnetic separators. This paper describes a model to predict the magnetic susceptibility of the roasted ore and its behaviour in the magnetic separation plant. The model uses a classification of the ore as a function of the size and magnetic susceptibility of the particles. A subsequent division into mineral species allows the simulation of the magnetic separation process. The model is used to assess various operating options when process disturbances occur.INTRODUCTIONOre processing operations consist of ore size reduction followed by the recovery of valuable species in a concentrate that is subsequently sold for its minerals or metal content. The concentration processes are based on the physical and/or chemical properties of the minerals contained in the ore. Flotation is typically used to recover minerals of base metals such as copper, zinc, lead or nickel. Iron ore and other dense minerals are typically concentrated by gravity separation processes. Magnetic separation uses the magnetic properties of the minerals to concentrate magnetite and other minerals, to clean coal concentrate and to recycle ferrosilicon for dense separation processes (Brophy, 1985).Magnetic separators can be divided into low and high intensity separators and high gradient magnetic separators (Gillet, 2008). Most of the low gradient magnetic separators are built as rotary drums that are operated in wet or dry conditions. Dry magnetic drum separators are used by Rio Tinto Fer et Titane in Sorel-Tracy, Canada to concentrate hemo-ilmenite from the ore extracted at the Lac Tio Lake mine near Havre St-Pierre, Canada. The analysis of production data suggests that process improvement could be achieved by identifying key variables for the control of the magnetic separation circuit and/or by modification to the circuit flowsheet. The use of a process model was considered to be an effective approach to conduct a preliminary analysis of the circuit with a view toward process optimization. However, the literature contains few detailed studies dealing with the modelling of magnetic separation processes."

Jan 1, 2011

By Ross Nairn

"Tulawaka Mine is a joint venture between Pangea Minerals Limited 70% (a wholly-owned subsidiary of Barrick Gold Corporation) and Northern Mining 30%. Tulawaka Mine is located in North West of Tanzania in the Lake Victoria Goldfields. Tulawaka Mine is scheduled to process 360,000 tonnes per year at an average 11.5 g/t head grade over a 4 year mine life.The Tulawaka Process Plant uses single stage crushing, single stage SAG milling, gravity, intensive leach of gravity concentrates, CIL, Zadra desorption and cyanide detoxification to process the ore. Gold recovery exceeds (or is expected to) 95%.The Process Plant was designed and constructed under the supervision of Ausenco Engineering of Australia. Site works commenced in January 2004, Process Plant construction commenced in July 2004 and the first ore was presented to the Process Plant 26th February 2005. The first gold was poured on 15th March 2005. All construction contractors were demobilized from site 7th April 2005. Major achievements have been 3.4 million hrs LTI free during construction and operation to date, training of the Tanzanian workforce at Bulyanhulu Mine prior to commissioning, a succession plan to replace expatriate personnel with Tanzanian staff and significant over performance of the Process Plant against design.INTRODUCTIONTulawaka Mine is situated approximately 160 km south west of Mwanza in the western Lake Victoria Goldfields District of north western Tanzania. The property is held under a joint venture between Pangea Goldfields Inc (70%), a wholly owned subsidiary of Barrick Gold Corporation, and Explorations Minieres Du Nord Ltée (30%). A location map showing the position of the operation in Tanzania is shown in Figure 1.Mine site staff at Tulawaka comprises a combination of Tanzanian and Expatriate personnel. All Pangea personnel live on site and commute to their place of residence for their R&R on a 9 weeks on 4 weeks off roster."

Jan 1, 2006

By S. A. L. Read

"The intact rock constant, mi, is one of the three basic input parameters required for the widelyused Hoek-Brown failure criterion. Values for the constant should ideally be determined by statistical analysis of laboratory test data. In this paper the influence of the inclusion or exclusion of tensile test data on derived values is discussed. We firstly investigate the relationship between direct tensile strength (DTS) test values and Brazilian tensile strength (BTS) test values based on a literature search, finding that the correlation between the two test types is DTS = 0.9*BTS, independent of the lithology being tested. Secondly, using the shear strength database of Douglas (2002), we examine the influence of confining pressure range and the inclusion or exclusion of DTS and BTS test values on calculated values of mi.Chief amongst the influences was the exclusion of tensile data in the calculation procedure, particularly when the Hoek triaxial confining stress range requirement (?3?max = 0.5?c) was not satisfied. Based on a reasonable 1:1 relationship between R (the ratio of unconfined compressive to tensile strength), use of actual tensile data in the calculations for the Hoek brown failure criterion is considered to be a simpler and more robust approach to the use of a tensile cutoff based on empirical criteria such as that of Fairhurst (1964). We advocate the fitting a failure curve using compressive and tensile test data as the most reliable means of calculating mi, while at the same time satisfying requirements as originally advocated by Hoek relating to the appropriate triaxial confining stress range (?3?max = 0.5?c) and sufficient (>5) evenlyspread data points. In the absence of triaxial data the use of R provides a practical means of obtaining estimates of mi that are more robust than guideline values."

Jan 1, 2015

By Grant Goddard

Cameco?s ?Double U? Strategy ? Double existing production ? To 40 million lbs U3O8 annually ? By 2018 ? Existing operations ? Saskatchewan ? United States ? Kazakhstan ? Projects under evaluation ? McArthur River expansion ? Kintyre (Australia) ? Inkai Block 3 (Kazakhstan) ? Development properties ? Cigar Lake project Measures of Success ? Safe, healthy and rewarding workplace ? Supportive communities ? Clean environment ? Outstanding financial performance

Nov 1, 2011

By A. J. Paul Laprairie

The process for which it is to be used is too often the only consideration in the design of a vessel. A de-sign allowing for practical manufacture and erection, as well as for proper maintenance, can often give over-all economies. Most platework in-stalled today is of welded construction. Therefore, metallurgical control is important in its manufacture. Also, because many concentrating and re-fining processes tend to be corrosive, the subject of protective coatings as a part of the manufacturing process is extremely important. The plant de-signer should know how to evaluate and specify controls for the metallurgy and for the coatings. Mining operations are becoming more sophisticated in the field of mechanical engineering. More and more emphasis is being given to preventive maintenance. The first step in any maintenance program, however, is good inspection service. This paper will suggest methods for the inspection of platework, and outline methods for repair and replacement.

Jan 1, 1963

By M. F. Goudge

BRUCITE associated with highly metamorphosed Precambrian limestone was discovered in the vicinity of Rutherglen in northern Ontario by the writer during field work on the limestones of that district in 1937, and later was identified in similar limestone at Bryson and Wakefield, Quebec. The brucite occurs as granules disseminated through the limestone (Figure 1) and comprises from 20 to 35 per cent of the rock. Such rocks may be referred to as predazzites or pencatites, depending on the proportions of the constituent minerals. In this paper, however, the general term brucitic limestone is used to designate limestone containing brucite. In none of the deposits does the magnesia content of the rock approach that of magnesite, and in the deposits near Bryson and Wakefield the magnesia content is only that of dolomite. Therefore, without some method of concentrating the brucite, the deposits would be of little or no more value as a source of magnesia than is ordinary pure dolomite, which is abundant in many parts of Canada. Investigations in the laboratories of the Bureau of Mines have, however, resulted in the development of a method whereby, from certain of the deposits, pure calcined brucite, or magnesia, in granular form can be obtained, apparently at a cost that will enable it to compete in eastern Canada with imported magnesia. The granular magnesia so obtained appears to be highly suitable for use in basic refractories, for making magnesium metal, and for various other purposes for which magnesia is commonly used. Prospecting in the neighbourhoods of the original discoveries has resulted in a number of other deposits being found in each of the three areas, and there is now apparently available s1.dficient brucitic limestone of a grade that will lend itself to commercial exploitation to supply for many years a large part of the present and prospective Canadian market for magnesia and its products. Furthermore, it is expected that additional deposits will be discovered as prospectors and others become more familiar with the appearance of brucitic limestone.

Jan 1, 1940

By E. R. Packer

"The mill of Anaconda Britannia Mines is located on the eastern shore of Howe Sound, approximately 32 miles north of Vancouver, British Columbia. The mill has a daily capacity of 3400 to 3500 tons and at the present is treating chalcopyrite-pyrite ore from which only the copper mineral is concentrated. For a clear conception of concentrate filtering and shipping practice at Britannia perhaps a bit of past history should be related.For many years the mill concentrated copper and zinc minerals and intermittently a pyrite concentrate was produced. It was general practice to ship copper concentrate by towed barge down Howe Sound, across Juan de Fuca Strait and thence down Puget Sound to Asarco's smelter at Tacoma, Washington. Zinc concentrate was loaded in hopper bottom rail gondolas spotted on rail barges and towed to rail heads in Vancouver, thence by rail to Anaconda Reduction Works in Great Falls, Montana. Most of the pyrite produced was shipped by ocean freighters to Japan and Taiwan with an occasional barge load of 2000 to 4000 tons to nearby customers in Vancouver and the state of Washington.In recent years, because of smelter shut-downs for one reason or another, mostly strikes, a considerable amount of copper concentrates has been shipped by ocean freight to Japan and in 1971 several lots were loaded in gondola cars and shipped by rail to the Anaconda smelter in Anaconda, Montana, because Asarco's smelter was forced by municipal and state anti-pollution laws to limit the amount of S02 emission from the smelter stacks. Zinc concentrate production was halted in the early part of 1Y70 because of zinc depletion in the ores and pyrite production was stopped in May, 1971, because of a lack of markets.Filter equipment in the Britannia mill consists of conventional disc vacuum filters and reciprocating vacuum pumps. The copper concentrate filter was installed in 1923 as a 6 x 8'6"" American disc type manufactured by United Filter Corporation, The zinc concentrate filter, now converted as a spare for copper concentrates, is also a 6 x 8'611 American disc manufactured by Traylor Engineering and Manufacturing Company and was installed the same year. Formerly, there were, in addition, two 4 x 6' disc filters for pyrite and two 6 x 6' disc filters to de-water bulk flotation concentrates ahead of the regrind mills. Installed vacuum pumps were two Ingersoll Rand 22"" x 811 and one 22"" x 9"". One of the smaller machines has since been scrapped.At the time of the writer's transfer to Britannia in 1965, the entire filter system was operating as a unit using two vacuum pumps and a common filtrate tank with a 2"" SRL filtrate pump for five operating filters. The regrind and pyrite filters were in continuous operation and the co11p('r concentrate filter alternated with the zinc concentrate filter because both copper and zinc concentrates were transp0rted to storage by the same conveyor belt."

Jan 1, 1972

By Paul Bedard, Réal Daigneault, Guy Perrault

"La mine Lamaque est située a Val d'Or, Québec; les roches hônes appartiennent au groupe de Malartic, partie supérieure, et sont des andésites et des pyroclastites. On y retrouve deux formes d'intrusifs; des petites cheminées (ca. 150 m D) et des dykes (ca. 10 m d'epaisseur). Les petit es cheminées contiennent:1 - des diorites et des tonalites (cheminées principale, est et ouest) d'affinité calco-alcaline: Zr 140 ppm, Sr 761 ppm, P2O5 0.31% et (La/Sm)n 3.0;2 - des diorites (cheminée 4) d'affinités tholéiitique: Zr 32 ppm, Sr 181 ppm, P2O5 0.27% et (La/SM)n 1.5.La diorite de la cheminée no 5 contient deux fractions, une de chacune de ces deux affinités. Les dykes tant de porphyre feldspathique quartzifére que ceux de prophyre feldspathique sont d'affinité calco-alcaline: Zr 83 ppm, Sr 500 ppm et P2O5j 0.10%.Le gisement de 10 mine 2 est filonien: veines subhorizontales (""flats "") surtout et veines sub-verticales dans des zones de cisaillement. Le dernier réajustement structural de direction de compression nord-sud a broyé le quartz des veines existant es et rendu possible leur minéralisation. Les veines minéralisées contiennent du quartz, de la tourmaline, de la calcite avec des traces de scheelite, de pyrite et d'or; elles sont bordées par de minces (2 à 20 cm) bordures d'altération où l'on retrouve un enrichissement en carbonate, paragonite, apatite, rutile, saphène et zircon et où les phases ferromagnésiennes sont disparues. On a documenté le migrations géochimiques suivantes:I - de la bordure d'altération vers l'éponte, K2O, Rb et MgO;2 - de l'éponte vers la bordure d'altération, Na2O;3 - de l'éponte vers la veine, SiO2.P2O5, TiO2, Zr, Y, Nb et CaO sont enrichis dans la bordure d'altération."

Jan 1, 1983

By F. C. Lendrum

"This paper had its origin in a panel discussion organized by the Canadian Uranium Producers Metallurgical Committee (CUPMC) at their Annual Meeting in Blind River in May, 1964. The reason for the panel was the formation of the National Uranium Tailings Research Program funded in the amount of ten million dollars by the Federal government. According to the bureaucrats in charge the program would seek to solve the perceived problems as well as any actual problems they believed existed with uranium tailings. Dr. Allan Ashbrook of Eldorado Nuclear chaired this panel and his summation of the panel's purpose was set out as ""Regulation and the Regulatory Process in the Nuclear Industry, Where Have We Been, Where Are We Now and Where Are We Going""?"" This paper will try to relate these questions to the whole mineral industry.The Canadian Mining Association has been telling us our natural resources are today required only if they are competitively priced with those produced in so called ""third world"" countries where labour rates are lower, environmental restrictions may be less and every effort is made by the local government to sell their product. It is in this hostile economic climate that the Canadian mining industry now finds itself. Before going further I want to stress these comments apply only to: a) Mines financed by private capital in a free enterprise society.b) Mining companies want to operate in an environmentally safe manner. However, they must earn a profit because no company financed with private capital can borrow money ad infinitum.WHERE HAVE WE BEENNone of us today would want to return to the days when the mill waste management system consisted of pumping the tailing to the nearest slope and letting nature's law of gravity do the rest. This was the way it was in early gold mines in Nova Scotia, tin mines in Cornwall, England or silver mines in Cobalt, Ontario and survives today in countries where climate, customs and methods of doing business are far different from Canada. As mill tonnage rates increased, more sophisticated systems evolved often designed for mining areas with different climates. Systems imported from arid climates such as south-west United States retained the solids but allowed bacterial oxidation of the sulphides promoting acid drainage. Environmental regulations were introduced and Canadian mines learned to handle tailings in our climates."

Jan 1, 1986

By Dayle Denton, Lloyd Buckingham, Kenneth G. Thomas, Jacques McMullen

"The dry grinding and leaching circuits of Barrick Gold’s new Roasting Facility at Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs.Crushing is a two stage process using gyratory and cone crusher. Ore is stockpiled and then reclaimed to two parallel dry grinding mills. The double rotator dry grinding mills include a drying chamber, coarse and fine compartments and utilize a gearless motor drive (GMD) or “wrap-around”. In-circuit product transfer is accomplished with air slides and bucket elevators. Finished product separation is performed by both static and dynamic classifiers with the final product captured in baghouses. Recycle of unfinished product utilizes cascade chutes.The final ground product reports to two 2000 ton roaster feed silos. The two-stage oxygen flu-solids roasters with their associated gas train are the subject of a separate paper.The cyanide leach circuit is a standard carbon in leach system with circular swept screens for interstage carbon retention. The loaded carbon is sent to the existing Goldstrike autoclave plant for stripping and regeneration. Tails, after cyanide destruction, are deposited in the existing tailings dam with tails from the autoclave facility.Throughout the circuit, Clean Plant Design criteria were used to assure environmental compliance, ambiental acceptability and ensure worker health and safety. The commissioning and operation of the double rotator grinding technology has been very successful at Barrick Goldstrike."

Jan 1, 2001

By A. J. Monhemius

This paper reviews the history of modern iron-control processes in hydrometallurgy. Attention is paid to processes developed in the electrolytic zinc industry for removal of iron from zinc sulfate leach liquors and the problems faced by the industry in the safe disposal of the iron residues produced by these processes. Past lessons learned are projected onto current efforts to develop hydrometallurgical processes for treatment of copper sulfide concentrates. It is argued that any attempt to create a \u201chydrometallurgical copper smelter\u201d will fail, unless methods are developed that can recover iron in a form that can be directly used by the steel or pigment industries.

Jan 1, 2017

By T. A. Rickard

FROM AN OLD MANUSCRIPT THE text for this contribution to the history of the Patio process is a page taken from a Spanish manuscript of Bartholomé Arzaj Sanches y Uela, now in the possession of the library of Brown University (see Figure 1). I owe the photographic print to the courtesy of the librarian. The date, as will be seen, is 1577. The subject is the treatment of silver ores at Potosi, in old Peru, but in modern Bolivia. The group of drawings (see Figure 1) is entitled "Arrangement of the machines in which the ores of silver are ground on the bank of Potosi, the one of two batteries and the other of one". First, top-left, we have the sketch of a "machine of one battery" operated by a water-wheel. From this mill the water runs in part along an aqueduct supported by pillars to the two-battery mill and in part down the hillside, where men are at work with "tubs, which are called cochas, in which are washed the charges of ore and amalgam". Along the top of the page are shown the "various offices in which are stored the copper, the salt, the ucha [llama dung, used for fuel], the lime, and other materials for the re-duction of the ores". To the right of these are "apartments and warehouses in which is stored the ore brought down from the mountain"?the cerro de Potosi. Through the arched portal come the "sheep [llamas] on which is brought down the ore". To this is added a reference to "the second gate, which closes the whole works". On the level above the aqueduct are seen six men carrying skin-bags that contain water. This is being sprinkled on the ore. On the extreme right are six more of these water-carriers. Next comes the two-battery mill. The mortero, or mortar, is marked on the right. Another description says, "Stone, on which the stamps crush the ore, which is called a mortar". To the left of these are indicated "screens of wire in which the ore is sifted after it has been crushed". Farther to the left, near the ore-washers, is a "shed, in which is placed the metallurgist to test the ore of the boxes". Along the left side of the page are sundry buildings, one of which is labelled a "shed in which are placed the cones of silver". Near it, lower, to the right, is the "furnace, in which are roasted the sulphides to facilitate treatment". Farther to the right is the "place where the Indians mix the charges of sulphide ore, which is called a buitron". Alongside is a "buitron in which the charges are prepared for reduction". Inside is a container, to which are attached the words "measure, called topo" On the extreme right is "another buitron in which the Indians mix the ores with their feet, as well as the heaps for the preparation of the reduction". Near the bottom, on the extreme left, is the "chapel where the holy sacri¬fice of the mass is celebrated". Under the first buitron is the "place where they dry the moist ores, called pãpear".

Jan 1, 1935

By M. S. Badollet

"IntroductionASBESTOS FLOATS may be defined briefly as blends of air-borne particles of fibrous asbestos and dusts produced during the milling stages and collected by Cottrell precipitators, dust sheds, or bag-houses.The various grades of asbestos floats on the market contain fibrous asbestos particles ranging in length from microscopic to approximately 1/4-inch. The fines or dusts present in the floats are from 40 microns to 2 microns or less in cross-section.Airborne asbestos particles are of diverse length because they are collected at numerous places in the mill. There are: (1) dusts removed from dry rock storage bins, (2) dusts removed from rock and fiber screens, (3) particles from the tops of collectors, and (4) fines removed by suction from the processing equipment. Sometimes the airborne particles are kept segregated, so that there is a partial separation by gravity. This is accomplished by a series of dust chambers enclosed in a long, rectangular building. The longest and heaviest particles fall nearest to the air flow entrance, the smallest at a point farthest away and nearest the exit. Sometimes the air from the dust chamber building is passed through a series of bag-houses or electric :precipitators ,to collect the extremely fine particles which normally escape to the atmosphere."

Jan 1, 1952

By A. L. Mular, R. P. Edwards

"The operation of flotation circuits is often regarded as a combination of art and science. Expert systems offer a method by which the art may be captured and supervisory control of flotation circuits fully realized. Operating knowledge, the art, can be consistently employed to enhance regulatory control through the judicious application of an expert system. Using an expert system, a supervisory control routine was developed, and successfully implemented, in the copper flotation circuit at Brenda Mines Ltd.The expert system ran in conjunction with regulatory PI controllers on a personal computer. The expert system received assays via an on-stream analyzer and adjusted regulatory loop setpoints as required in real-time. From its commissioning in November 1989, to the end of the mine's operation in June, 1990, the ES was enthusiastically embraced by the operators and attained operating levels superior to those achievable manually.INTRODUCTIONExpert system (ES) software springs from research into artificial intelligence and is currently making significant inroads into business and industry. Proponents of ES's make many attractive claims; they are a means of capturing the knowledge of experts and they can be programmed by non-programmers. To date, most uses of this software in the process industry are in off-line applications, meaning that the applications are not tied directly to operating (on-line) environments. Moreover, in on-line environments, they are typically employed as advisors and only suggest changes. Human operators are required to close-the-loop to the process. Yet, ES's should be applicable to operating environments and, if the claims of the proponents are valid, should also be better than existing tools. As an intelligent controller an ES must use the knowledge of experienced operators, apply it directly to a process and do this without the intervention of human operators. On-line applications have been successfully employed in the closed loop control of SAG circuits (Herbst et al., 1989) and flotation circuits (Hales, 1989). Harris and Kosick (1988) detail an implementation for flotation control at the Polaris Mine."

Jan 1, 1991

By M. W. Grabinsky

Better in situ performance data is required in order to advance the rational geomechanical design of cemented paste backfill systems. A few in situ test programs have been conducted, but these have suffered from too few measurement locations within the stope and have not used enough different types of transducers to fully capture the information of significance. In this paper the important geomechanical design aspects are listed, the underlying physical phenomena are described, and some previous in situ measurement efforts are reviewed. A new approach to in situ measurement campaigns is then described including measurement techniques, locations, and the logistical aspects of mobilizing transducers in an active mining environment. A work-in-progress is used to illustrate the principles and concepts involved.

May 1, 2007

By Carolyn Kenney, Jianjun Liu, Zhenghe Xu

"The flotation of fine particles has been a challenge to scientists and engineers in mineral processing. A novel concept of reactive oily-bubbles as carrier to float fine particles is described in this paper. The reactive oily bubble flotation is considered attractive for fine particle flotation. In addition to the role of fine particle agglomeration by oily films, the surface properties of air bubbles coated with a thin oil film can be better controlled for the desired selectivity by adding certain types and concentrations of water insoluble collectors into the oil phase. This approach can eliminate the addition of collector to the aqueous phase, avoid undesired synergetic interactions among collectors, activators, depressants and dispersants present in slurry, minimize undesired activation of gangue particles and significantly reduce the amount of collectors needed.The concept of using reactive oily-bubble to achieve selective flotation was demonstrated in contact angle measurement and by microflotation tests with fine sulphide minerals: sphalerite and galena in this paper. The flotation behavior of sulfide minerals can be radically modified with adjustment of solution pH, addition of depressant and activator as in conventional flotation. The successful separation between PbS/SiO2, ZnS/SiO2 and PbS/ZnS was demonstrated using mixed mineral systems. Compared with conventional flotation, the reactive oily-bubble flotation showed a stronger collecting power.INTRODUCTIONThe challenge for fine particle flotation has long been recognized and well documented (Fuerstenau, 1980). Because of drastic changes in surface properties of fine particles and associated physicochemical and hydrodynamic conditions of flotation systems, fine particles responded poorly to the conventional flotation processes. For instance, the small mass and hence low inertia of fine particles would result in a low efficiency of collision and attachment of fine particles with flotation bubbles. Large specific surface area of fine particles, on the other hand, would cause an increased reagent consumption. Dominating colloidal forces of fines may cause slime-coating, accompanying a low selectivity (Somasundaran & Arbiter, 1979; Fuerstenau, 1980; Sivamohan, 1990)."

Jan 1, 2003

"INTRODUCTIONGold tailings retreatment plants have been operated for many years throughout the world. Several large tailings retreatment facilities have been operated profitably in South Africa since 1976 and there are tailings retreatment operations in Canada currently in production with more in the feasibility stages.The Timmins Gold Tailings Project of ERG Resources Inc. was designed to treat 8,000,000 tonnes per annum of gold tailings for an eight month operating season, and commissioning of the operation began in July 1988. The payback period for this project is about 3 years which corresponds to an IRR of 30%.This report summarizes the metallurgical characteristics of the reclaim tailings, describes the process flowsheet which was developed to enable ERG to economically recover gold from the Timmins area tailings, and reviews commissioning activities."

Jan 1, 1989

By K. Raht

LEAD poisoning is perhaps the oldest and, until recent years, the most misunderstood of all industrial diseases. Hippocrates appears to have recognized a relationship in the colic experienced by a patient who worked with metals, and the ancient literature is filled with references to the colics and 'dry bellyaches'. The colic and other sequalæ following drinking of lead-bearing waters and, particularly, wines has excited possibly more comment in the older medical literature than any other ætological factor. It was not until1656, when Stockhusen definitely connected the colic of the workmen with the fumes given off in the process, that the true danger to those working with lead was recognized. Unfortunately, something over 200 years elapsed before industry took any note of Stockhusen's discovery; it remained for Legge and Goodly and investigators of the early 1900's to forcibly educate their profession and industry to the manner in which lead gained entrance to the body. The work of Legge and Goodly was published in 1912 and the clearness with which these investigators presented the scientific data which they had accumulated will mark this volume as perhaps the first and most important contribution to our modern knowledge of the subject. It also ushered in a period when, in the short space of thirty years, lead poisoning has been reduced from one of the most baffiing and widespread o industrial diseases to one which can be anticipated and controlled. The next great contribution came in 1926 with the publication of the work of the Harvard group. Here, for the first time, was the physiological behaviour of lead laid bare, and it is to the discoveries of these authors that we owe our modern treatment of lead poisoning.

Jan 1, 1941