Search Documents

By P J. A Lever

This paper presents details of CRC MiningÆs work with waterjet assisted blasthole drilling. The objective of this work was to investigate techniques that reduce the cost and increase the productivity of blasthole drilling. The focus is on a technology that uses a high pressure waterjet to assist the conventional rotary rock cutting action of a tricone drill bit. The potential benefits of this technique are increased productivity, reduced drill bit wear and reduced hole deviation and hence improved quality of drilling. This paper describes the results of a laboratory based experimental program comparing conventional tri-cone drilling performance to the proposed waterjet assisted approach. Additionally, work has been completed looking at the more practical issues around the collection and sampling of drill cuttings and water recovery (recycling) when drilling with a waterjet. These studies have demonstrated that waterjet assisted drilling can significantly increase the rate of penetration over conventional rotary drilling. For the best-case experimental result, the relative improvement was over 40 per cent. More importantly, it is a starting point for examining alternative uses of the additional drill productivity obtained from waterjet assisted drilling. For example, increased drill productivity could be used to improve rock fragmentation by drilling a tighter blasthole pattern in the same time period. an existing drill fleet, then the drill fleet size could be reduced, or improved rock fragmentation could be achieved by drilling a tighter blasthole pattern within the same time period.

Jan 1, 2004

An image analysis system has been built which automatically digitizes camera input of rock fragments, analyses the digitised data to determine the sizes and shapes of the rock fragments, and outputs the analysed data to a printer in the form of a histogram or a scatter chart. The high speed of such a system allows for direct collection of data from material thrown into the air by blasting, material travelling on a conveyor belt, and material free-falling on to a stock-pile or into or out of a rock-crusher. Data on the blasted, un-crushed material provides information on changes in the lithology and structure of the rock face as it is quarried or mined: flatter fragments may represent approach to a brittle, unstable shear zone, or a change from sandstone to shale; so that the informa- tion reflects the effect on the sizes and shapes of the fragments by the blasting process and/or by the rock structure. The size and shape distributions of rock fragments produced during blasting and during processing may now be continuously monitored. Such detailed analysis of the results of fragmentation is labour-intensive and expensive when the size and shape distributions are obtained manually, but is cheap and efficient when using this image analysis system. Such a system will enable the results of blasting, quarrying, mining and crushing to be cheaply analysed and correlated with current and changing indus- trial practice so leading the way to increased productivity.

Jan 1, 1988

Results are presented of the investigation of gas dynamics of the blast furnace process obtained on laboratory models and operating furnaces. Gas residence times were measured using a helium tracer technique developed for the purpose. Residence times were determined in furnaces of 1007 m3 and 1719 m3 and results used in the calculation of the burden parameters and to estimate the distribution of the gas flow along the furnace radius. The effect of tuyere injection of coal dust on gas distribution was also investigated and the advantage of continuous injection compared with intermittent injection is noted. The unevenness of gas distribution across the furnace area is found to correlate well with differences in the size analysis of the iron-bearing component of the burden. The mixing of the gas streams between the neighbouring raceways was studied. It is shown that in the central region of the furnace gases from every tuyere are mixed together, whilst in the peripheral regions mixing is more localised and includes only the sections consisting of five adjacent tuyeres. A solution is proposed to the problem of a theoretical evaluation of the critical gas velocity. A simple relationship between the Reynolds and the Archimedes numbers was obtained from which, after substitution of the burden size data and the gas parameters, it is -possible to evaluate the critical gas velocity. Conclusions include information relating to the optimisation of the gas distribution and views on reducing gas injection at elevated furnace levels.

Jan 1, 1975

By Hegedus M

The Hydrogeological Survay of the bauxite mines in Hungary was establisned 30 years ago. The goal of the HS has been to collect the all available date needed to solve the hydrogeological problems of bauxite mines. The results of activity of the HS have been summarized in the annual reports-. This report is going to present a few methods to evaluate the hydrogeological properties of fissured, karstic rock ie. the evaluation of drilling mud losses, the statistics of core samples evaluated by a special computer program for calculation the porosity and permeability of the rocks. An experimental injection test is presented together with the development of a new portable instrument to get signes of the water table change during the injection test in every two second. It can be proved that the flow around the well may be a transient one if the yield of the injection exceeds a definite one (Figure 2.). It was observed that the permeability calculated from the pumping test date may be 1.2-1.6 time higher than it coming from the injection test. A practical example is presented also how to use the results of the HS for designing the dewatering of a new mine together with an analogous computer model to forecast the yield expectable for making the drift tunnel. A suggestion based on the hydrogeological feature has been done for the dewatering without using electric energy (see Figure 3.-6.).

Jan 1, 1988

By T Ye Koltunova an, L A. Otrozhdyonnova

This paper presents the results of studies on the development of an efficient non-cyanide technology for processing massive, finely disseminated, copper-zinc ores of the Urals deposits. Copper is mainly represented by chalcopyrite and zinc û by sphalerite. The main ore mineral is pyrite, with its content in ores varying from 50 to 80 per cent. At the present time, separation of copper concentrate at the Urals concentrating plants is achieved in a lime medium by non-cyanide technology using sodium sulfide and zinc sulfite as depressors of zinc and iron sulfides and butyl xanthate as the collector. Copper content in copper concentrates amounts to 15 - 17 per cent; considerable losses of zinc are associated with copper concentrate and final tailings. Various collectors were tested during the studies: xanthates and aerofloats with different lengths of hydrocarbon radicals, thionocarbamates, Aerofine 3418A of Cytec Industries, reagent S-703G of Mineral Reagents Int, and modifiers û sulfur dioxide, sodium sulfide and zinc sulfite, with a pH of the medium varying from 5 to 12. Optimum results of copper concentrate separation were achieved in a weakly acidic medium using S-703G as the collector and sulfur dioxide and zinc sulfite as modifiers. The copper content in the copper concentrate was increased by 4.8 per cent. Total copper recovery into the copper concentrate and zinc recovery into the zinc concentrate exceeded five per cent.

Jan 1, 2005

The Musselwhite mine, located in northwestern Ontario, Canada, has been an underground narrow-vein gold producer since the spring of 1997. As an exploration project at the feasibility stage, much effort was undertaken to generate a geostatistical resource model that would integrate the orebodyÆs geological features, as well as the controls on mineralisation. Today as an operating mine producing over 200 000 ounces of gold per year, reconciliation studies of the tonnes and grades treated at the mill, with the feasibility model, for longer time periods, and with the grade control models, for shorter time periods, show results that are in good agreement. It was clearly demonstrated with the reconciliation to production, that the key to good reconciliation remains in the proper selection and application of the geological resource estimation method. The application of a grade interpolation technique capable of capturing threedimensionally pertinent geological features, as well as accounting for spatial grade continuity, proved to be successful in the predictability of tonnage and grade at the Musselwhite mine. Along with good mine practices, this approach, which was carried through to the operation, has produced excellent reconciliation results. The ongoing reconciliation studies at Musselwhite allow for a constant revision of the grade estimation strategy. In return, this optimisation process adds value by raising the accuracy level of production expectations. As this is an evolving practice at the mine site, further implementation developments are recommended to integrate these reconciliation procedures on a more regular basis.

Jan 1, 2002

By T Raynlyn, J J. Campbell, J M. Young

In order to correctly predict the performance of beneficiation processes, such as hydrocycloning or ultrasonic treatment of iron ore fines, it is important to understand possible changes in size distribution, mineral composition and textural peculiarities. During beneficiation processes, iron ore can be subjected to various physical actions which may result in changes in size distribution. In the case of soft or friable ores, attritioning and/or deagglomeration may have a significant effect on both separation performance and product stream specifications. Optical image analysis tools, which give statistical information on a particle by particle basis, can help in better understanding the response of the ores to these processes. An experimental study has been conducted to investigate the response of a haematitic-goethitic iron ore to a combination of stirring and ultrasonic treatment. The effect of stirring and ultrasonic treatment on the size and mineral distribution has been quantified using image analysis and automatic ore texture classification. This approach has been applied to several size coarse fractions of the initial feed and product. The results show that, following treatment, the mass proportion of ore texture classes which contained higher amounts of ochreous goethite and kaolinite had significantly decreased compared with that in the feed, while the proportion of texture classes where haematite was the major mineral had increased. Liberation analysis also showed a significant increase in the proportion of particles with more than 95 per cent haematite and vitreous goethite.

Jan 1, 2007

By Ormsby W. R, Farrar L

The stratigraphy of the central Pine Creek Geosyncline has been simplified into a three-fold subdivision comprising the Batchelor, Frances Creek and Finniss River Groups. The Batchelor Group consists of a sequence of shallow water coarse clastics and crystalline carbonates and is conformably overlain by the marine carbonaceous shale dominated Frances Creek Group. Interbedded within the carbonaceous shale are turbidites, iron formation, tuffs, carbonate and non carbonaceous shale. The Finniss River Group is a flysch sequence of greywacke and mudstone. The stratigraphic and structural evolution and igneous history are all interrelated. Although the Batchelor Group may have formed in a tensional regime, it is likely that regional compression and accompanying thin skinned deformation began during deposition of the Frances Creek Group. Continued compression resulted in D2 folding d6collement deformation, wrench faulting in compressional zones and thrust faulting. Occasional relaxation of compression is marked by a number of periods of basic intrusion and perhaps distal volcanism. The style of deformation within sediments varies away from granitic basement highs and is similar to that observed around salt domes and found in experimental diapiric models. Sedimentary facies changes also indicate local emergence of basement highs during sedimentation. As compression continued, the deposition of thick sequences of the Finniss River and El Sherana Groups brought about regional metamorphism. Relaxation of compression and waning of associated subsidence resulted in a relative increase in the rate of uplift and partial melting of diapiric sialic basement. In places, granitic magma moved upwards and crystallised forming grossly concordant bodies. Other masses moved laterally and formed extensive granitic sills. Later compression periods caused mainly brittle deformation which may have been strongly influenced by underlying basement fabric.

Jan 1, 1994

By I Auranen, J Raatikainen

IMA Engineering (IMA) and Mine On-Line Service (MOLS) companies have used on-line sensors for analysing ore and waste rock in mining for more than 25 years. Today IMA on-line sensors are used in various stages of the mining process including on-line analysis of drill cores, drill chips, ore and waste in loader bucket, ROM ore analysis on belt conveyor belt and in bulk ore sorting and in slurry analysis in concentrators. During years of extensive field experience and testing we have found that the waste rock dilution and ore losses create much larger economic and environmental losses than has been previously recognized. According to our studies the main reason is limited number of analysis already in exploration when drill cores or drill cuttings are used in block modelling. The same happens in production because too few and biased samples from benches are used to estimate the ore grade. Much more than today estimated amount of waste enters the mill and considerable volumes of ore losses happen at the same time. The ore grade on the benches and in muck piles is averaged and “homogenized” with averaged and biased samples. These are the main root causes of waste rock dilution and ore losses. Sensor based preconcentration can be the remedy to waste rock dilution and ore losses. This presentation will show examples of the use of on-line sensors in preconcentration when analysing ore and waste rock in drill cores, drill cuttings, on conveyor belt and in bulk ore sorting. Waste rock removal in preconcentration has direct effect on energy consumption in crushing and grinding and chemicals in concentrator. In concentrator waste is separated and goes to tailings pond, however, preconcentration directly reduces the volume of the tailings. In our presentation we will cover cases in base metals and in gold mines.

Nov 10, 2020

By White L. R, Boger D. V

The paper describes the surface chemistry and particle physics that control the fundamental flow properties (Theology) of mineral particle slurries. We further address, through a series of case studies, the design data that emerges from experimental studies of the flow properties of complex, high volume fraction mineral slurries. The case studies are drawn from mineral oxide concentrate processes, tailings dewatering operations and from filter cake production and management. The paper emphasises the essential links between design of process slurry handling systems and the control of the flow of such slurries by control of the pulp chemistry.

Jan 1, 1992

By D Van Doorselaere

The purpose of blasting during mining is to produce a muck pile that can be efficiently loaded and transported. There is an increasing awareness of the variation in muck pile characteristics and its economic implications. It is well known that good fragmentation by itself is not sufficient to optimise the muck loading efficiency. The swelling and configuration of the muck pile also significantly affect the productivity of the loading equipment. The characteristics of a muck pile depend upon the blast design parameters, explosive properties and rock mass geology. This study has focused on the dependence of muck pile configuration on blast design parameters, explosive properties and size distribution of the muck.The field work was done in two phases. In the first phase 12 blasts were monitored, while in the second, three blasts were monitored. The blast design parameters and explosive properties for each blast were documented and the following muck pile characteristics were measured:muck pile height and its distance from the facedistance of throwwidth of the power troughsize distribution by image analysis technique.The effects of burden, bench height, heave energy of explosive, row-to-row delay, powder factor and the mean particle size of the fragments on muck pile configuration were examined. It was observed that muck pile height and distance of throw are strongly influenced by the burden, bench height, heave energy of the explosive and the size distribution of the muck. The width of the power trough depends upon the row-to-row delay, powder factor and total burden. In addition, the effect of the fragment size distribution on the muck pile parameters has also been discussed.CITATION:Singh, S P and Van Doorselaere, D, 2015. The relationship between blasting parameters and muck pile configuration, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 369–374 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By C L Humphrey

Biological monitoring programs for environmental protection require techniques that will provide both early detection of possible adverse effects, and assessment of the ecological significance of these effects. Monitoring techniques must include responses sensitive to the impact, that can be subjected to rigorous statistical analysis and for which statistical power is high. Such issues in baseline research of 'what and how to measure?' and 'for how long?' have been the focus of a program being developed to monitor and assess effects of mining operations on the effectively pristine, freshwater ecosystems of the Alligator Rivers Region (ARR) in tropical northern Australia. Application of the BACIP design, utilising a form of temporal replication, to univariate data (single species) and multivariate (community) data is described. For new ventures in Australia (such as mining), monitoring programs should be designed to establish with high probability that an impact on the ecosystem no greater than a prescribed amount has gone undetected - as opposed to simply allowing development to continue as long as 'proof' of impact is not available. Such a precautionary approach represents a shifting of the 'burden of proof' and would require with the BACIP design, a minimum number of baseline years in order to achieve some desired level of statistical power in a test for impact. Power analyses conducted on two to five years (depending upon the technique) of baseline data from streams of the ARR indicate that the BACIP design would not impose developmental constraints on mining and that a policy of reversal of the burden of proof would provide the cornerstone required for managing such development in an ecologically sustainable manner.

Jan 1, 1994

By R L. Koenig

Previous papers at Metplant conferences have covered the options for crushing and grinding circuit selection. High Pressure Grinding Rolls (HPGR) may have considerable advantages over autogenous milling circuits but test work and evaluating different grinding circuits must be done to establish which circuit provides the best option. The Hawsons low grade magnetite project provides a specific example in using thorough test work, careful simulations and detail in design to allow the evaluation of grinding circuit performance. Fortunately tools are available for this evaluation and the test work for the Hawsons iron ore is detailed in this paper. The results of the test work and simulation indicates that although the Hawsons iron ore is competent in terms of autogenous milling given the medium hardness of the ore in the Drop Tests, the HPGR testing indicates that the use of HPGR is likely to use half the energy requirement. This is a characteristic of the Hawsons iron ore and is likely to be valid for other iron ores in the Braemer Iron Formation which stretches from the Hawsons lease in New South Wales to Razor Back and South Dam in South Australia. The Hawsons magnetite iron ore resource has been known from the early 1960s when CRA explored the area. However, the Pilbara region was discovered in this era and this led to development of high grade direct shipping grade hematite ores. Carpentaria Exploration (Capex) rediscovered the magnetite whilst undertaking multi-commodity exploration in the Broken Hill district during 2009. The magnetite grade was found to be low at around 16% Davis Tube mass recovery (DTR) but despite this, the project provides a positive business case as a result of the following key factors:• The mineralisation is particularly soft for crushing and grinding with a Bond Work Index of 6.3.• The mineralised rock fractures easily preferentially along grain boundaries.• The location is close to mining infrastructure and a skilled workforce in Broken Hill, 60km to the North East.• It is close to road and rail infrastructure for access to the resource.• The only contaminant in concentrate is silica.• The resource contains many billions of tonnes of magnetite mineralisation.The low Bond Work index is a key characteristic of the Hawsons iron ore and the use of autogenous milling and HPGR circuits is compared to other iron ores indicating why the plant energy requirement may be just as important as iron ore grades.

Aug 8, 2011

By D Michaelsen, S Miller

The Grasberg Mine is a copper and gold open pit mine operated by PT Freeport Indonesia (PTFI) and located in the high equatorial mountains of the Indonesian province of Papua. The climate is alpine/subalpine with little seasonal variation in temperature or rainfall. The daily average temperature ranges from about 2¦C to 14¦C and the annual rainfall in the vicinity of the mine and overburden stockpiles is about 4000 mm to 5000 mm. Mining of the Grasberg open pit will continue until 2014 at which time approximately 2750 Mt of overburden will have been produced. Current overburden production rates are 200 Mt per annum. The current mill rate is 230 000 t/day from the Grasberg pit (190 000 t/day) and the underground operations (40 000 t/day). The acid rock drainage (ARD) issues associated with overburden from the Grasberg operations were identified early in the mining operation. Almost all overburden placed to date has been Potentially Acid Forming (PAF). Laboratory testing has identified four main overburden types: limestone and non-acid forming (Green waste), PAF low capacity (Blue waste) and PAF high capacity (Red waste), and Heavy Sulfide Zone (HSZ), which contains greater than 20 per cent pyrite. Waste type block modelling indicates that at least 30 per cent of the overburden production from 2003 to the end of Grasberg pit operations will be limestone. Strategies are being developed to maximise the beneficial use of limestone through strategic blending and placement for ARD mitigation and control.

Jan 1, 2003

By I Doye

Acid mine drainage is a serious environmental problem caused by the oxidation of sulfide minerals responsible for highly acidic, sulfate and metals-rich drainage. Several methods of mine waste management have been developed that reduce liabilities on environment. Layered co-mingling of waste rock with compacted tailings, covers with capillary barriers effect, and co-disposal of waste rock and tailings are these new methods which are used to reduce the formation of acid mine drainage. These methods shield waste rock dumps from oxygen. These techniques could prevent oxidation reaction. In this study, alkaline industrial wastes are used with acid generating tailings to inhibit acid mine drainage. The alkaline wastes selected are cement kiln dust (CKD) and red mud bauxite (RMB). These alkaline materials are used to keep neutral conditions in the fine material layer and to inhibit the metabolic activity of Thiobacillus ferroxidans which catalyses the oxidation of sulfide minerals. A series of timed static leaching tests were performed by reacting samples of mine tailings with two, five and ten per cent alkaline material in order to characterise geochemical balance between liquid and solid phases. Column tests have been set up with oxidised tailings, waste rock, CKD, and RMB. Column tests have been carried out to simulate layered co-mingling, covers, liners, and co-disposal of waste rock and tailings. Column leach tests were conducted in order to investigate the long-term neutralisation potential of alkaline materials and the drainage water quality. Bacteria counting were performed on each sample after testing. The results obtained show that the addition of alkaline materials permit the retention of near neutral conditions in the fine material layer, thus increasing water quality and preventing bacteria development. In fact, the pH results show that the use of five per cent, ten per cent CKD or ten per cent of a mixture of CKD and RMB permit the retention of neutral pH conditions in the reactive layer. At these percent rates, the concentrations of Al, Fe, Cu, Zn, and SO4 in solution are significantly reduced compared to those obtained with the tailings only. In presence of waste rock, the relative position of the fine material layer is important. When the fine material layer overlaying reactive waste rock is composted of reactive tailings with ten per cent CKD and ten per cent (CKD:RMB), a delay was observed before achievement of near neutral pH. The neutral pH conditions remain stable over time. The mixture of CKD and RMB provides a better short-term neutralisation than the use of CKD alone. The use of alkaline materials is beneficial in order to reduce the concentrations of Fe and other metals such as Cu and Zn as well as the number of viable bacteria. The use of ten per cent RMB alone does not involve the neutralisation of reactive tailings. In the cases where the fine-grained layer are below or mixed with the waste rocks, the near neutral pH values are directly reached with ten per cent CKD. However, the pH values decrease rapidly and the number of viable bacteria increases.

Jan 1, 2003

The Canadian mining industry was in turmoil in the early 1980s. The post-war era based on reconstruction faded away after the high demands for minerals in the 1950s and 1960s. Also, the industry had the misconception that the demand growth would continue for ever but the rapid growth of resource industries in the third world in the 60s and 70s, resulted in worldwide production overcapacity. The Canadian mining industry eventually recognised the facts and took drastic action for cost control and innovation in technology. The cost control had an immediate effect on the survival of the industry but resulted in only limited incremental gains. The economic problems that the Canadian mining industry faced in the early 1980s can be viewed now as a blessing in disguise. It was realised that for the Canadian mining industry to survive in the 21st century further gains were possible only through innovative technology. This conclusion led to a flurry of activity to establish mechanisms and delivery systems for innovative technology in the mining industry. Despite the initial difficulties in accepting high technology in the mining industry, it is being used increasingly in mining operations and will make future mining operations unrecognizable to present day mining engineers. The concept of an underground mine without underground staff seems to be far fetched, but it is possible that mines of the 21st century will approach the concept of very few underground operating personnel.

Jan 1, 1988

By H Zhang, Y Wang, S Sukenaga, H W. Ni, H Shibata, W Z. Mu

The crystallisation behaviour of low melting point CaO-SiO2-Al2O3-MgO inclusions greatly affect the deformability of inclusions during the rolling process. The crystallisation characteristics of CaO-SiO2- Al2O3-MgO melts representing the oxide inclusions in Si-Mn killed steel were systematically investigated. The effect of Al2O3 and MgO contents on the crystallisation change were analysed under a fixed CaO/SiO2 in the complex inclusions. The continuous-cooling-transformation (CCT) and time-temperature-transformation (TTT) experiments were conducted. The results showed that the increase of MgO content increases the crystallisation ability of CaO-SiO2-Al2O3-MgO inclusions, while the increase of Al2O3 content has the opposite effect. The viscosity, liquidus temperature of oxide melt and also the initial crystallisation potential might be the reasons for the change in crystallisation behaviour. Also, the crystallisation activation energy could semi-quantitatively characterise the crystal growth during the crystallisation of inclusions. To obtain low melting point plasticized CaO-SiO2-Al2O3-MgO (CaO/SiO2=1) system inclusions, the Al2O3 content of the system needs to be controlled larger than 15 wt per cent and the MgO content should be kept at a small amount.

Aug 21, 2024

The current drill-and-blast method of tunnelling is cyclic and, for this reason above all others, has a future application potential which is lower than that of continuous methods. There is scope for progress in several facets of today's drill-and-blast tunnelling. But even if each of its unit operations and the synthesis of these were to be optimised, this conventional method will, in the long term, fail to be a serious competitor for tunnelboring machines (TBMs), roadheaders and the like. If its role in tunnelling is not to decline at an increasing rate, drill-and-blast will need to be transformed into a continuous system. Boring and cutting machines consume considerable energy (and expenditure) in creating rock fragments which are smaller than those required by muck-handling equipment. In this respect, blasting is more efficient. Mechanical methods are also less versatile and flexible and, when planning proceeds on a basis of meagre or inadequate geological data, cannot be costed as accurately. Currently, research gains for TBMs and roadheaders are greater than those for conventional tunnelling. If (as is likely) the disadvantages of mechanical methods continue to be reduced at a greater rate, the swing away from drilling and blasting will gain momentum.

Jan 1, 1987

By G J. Harbort, V Lawson, L Reemeyer

The Jameson Cell is a high intensity flotation device, which utilises induced air from the atmosphere. It was developed jointly by Mount Isa Mines and Professor Graeme Jameson of the University of Newcastle in the 1980s. It is proven to generate fine bubbles, in the order of 300 to 500 ¦m, in a high intensity, high shear and compact zone contained in the downcomer. This aerated mixture exits the downcomer into the pulp zone, which is the quiescent mineral and gangue separation zone. A number of Australian base metal flotation circuits feature a reverse flotation stage at the head of the circuit. Testwork and plant operating data has shown that the use of a Jameson Cell in the prefloat cleaner application has further improved prefloat gangue recovery and selectivity. Operation of a Jameson Cell in a carbonaceous/pyrite prefloat cleaner duty at the Mt Isa copper concentrator increased copper recovery and reduced pyrite in the copper concentrate. Testwork at Zinifex Century Zinc Mine showed a decrease in zinc losses by the utilisation of Jameson Cell prefloat cleaner. Appraisal of a Jameson Cell in a scalping role within the Mt Isa Copper Concentrator indicated significant benefits could be achieved.

Jan 1, 2005

By S Thomas, E Grimsey

Mining education in Australia has undergone another cyclical downturn over the past five years and several departments have been discontinued while others are still teetering on the brink of destruction. During this downturn Curtin UniversityÆs WA School of Mines (WASM) has managed to stay alive and well, but this has not been by accident. This paper outlines some of the strategies and experiences that have kept WASM in a strong position and offers hope to other departments and schools elsewhere that are still experiencing difficulty. This paper is also directed at all mining departments and schools that are certainly going to see it all happen again after the next mining boom turns to bust.

Jan 1, 2004