Search Documents

By May J. R

Exploration, including research, has fuelled the enormous expansion of the Australian mineral industry in the last three decades. Analysis of success and failure in exploration and research has therefore potentially powerful lessons and messages which may be used to influence the future shape and direction of the mineral industry. Research has been an integral part of organised corporate mineral exploration since its beginnings in Australia in the 1930s. In corporations, the activity generally called project generation or new project development is the main expression of exploration research but mostly it goes unidentified and poorly documented except perhaps when a successful discovery is made and reported on. The competitive nature of exploration means that extended and detailed analysis of corporate exploration research across the industry is impossible to achieve.

Jan 1, 1992

By D W. Airey

Frictional rock bolts are widely used because of their low cost. However, they have a thin wall section that makes them prone to corrosion, and they cannot be relied on to provide long-term ground support. It is difficult to assess the capacity after the bolts have been installed as they can only be pulled out if this has been allowed for during insertion. The questions of how long can the rock bolts function effectively and the effectiveness of various surface coatings, which can have significant cost implications are, investigated in this study.A series of accelerated corrosion tests have been performed on frictional rock bolts. The rock bolts, typically 900 mm long, have been inserted into concrete cylinders produced using a styrofoam insert to create the hole for the bolt insertion. Strata rock bolts with four surface coatings have been tested: uncoated black steel, galvanised, enduro (plastic coated) and coated with a proprietary aluminium/zinc alloy. Tests have been performed on two diameters of bolts. Following insertion of the bolts, the concrete cylinders were placed in a large drum filled with saltwater and current was applied to accelerate the corrosion process. The rock bolts were then extracted at various times after the commencement of corrosion. Comparison of the insertion and extraction resistances shows that corrosion initially increases the bolt resistance and that substantial section loss is required for the bolt resistance to drop significantly.CITATION:Airey, D W, 2014. Laboratory corrosion tests of frictional rock bolts, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 257–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By M-A Van Ende, N Kumar, I-H Jung

In order to utilise the powerful thermodynamic databases for process simulations, a concept called Effective Equilibrium Reaction Zone (EERZ) was introduced to couple thermodynamic database calculations and reaction kinetics. Using the EERZ concept, many process simulation models for steelmaking processes have been developed within the FactSage steelmaking consortium. After validation of the simulation results by comparing with plant data, the simulation models have been applied to improve plant operations. Several success stories of the improvement of real steelmaking operations are shared. A new user-friendly FactProSim software developed for building process simulations is introduced.

Aug 21, 2024

By N B. McCaffrey, V Glenn, C Johns, P D. Erskine, A T. Fletcher

"Underground coal mining is the dominant method of extracting thermal and coking coal in the southern and western coalfields of New South Wales. Monitoring mining-related subsidence forms an important component of environmental impact assessments and subsidence management plans, particularly when there are conflicts between the interests and requirements of mining and environment and community groups. However, there are few specific guidelines for monitoring the impacts of subsidence on terrestrial and aquatic ecosystems, leading to inconsistent policy approaches and highly variable abilities of monitoring programs to accurately detect biological change.This paper highlights the use of a conceptual framework to guide the development of a long-term ecological monitoring program at an underground coalmine in the Western Blue Mountains, New South Wales. Two pilot studies are described: determining the level of observer agreement to assess the condition of a vulnerable tree species (Capertee Stringybark) comparing field sampling methods for detecting a rare heath shrub, Epacris muelleri, using a power analysis to determine sampling intensity requirements.These examples demonstrate that investment in initial pilot studies to test different monitoring approaches can have long-term benefits for stakeholders by more confidently being able to detect potential impacts.CITATION:McCaffrey, N?B,?Glenn, V, Erskine, P?D, Johns,?C?and Fletcher, A?T, 2014. Detecting long-term ecological impacts of subsidence from underground coal mining – a tale of two pilot tests, in Proceedings Life-of-Mine 2014, pp 139–152 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 16, 2014

By R Berry, A Escolme

"Predictive geometallurgical models are being developed for the Productora Cu-Au-Mo deposit based on geochemistry to reflect variability in Cu species based on Cu sequential leach data (ie oxide, transitional-oxide, transitional-sulfide, sulfide and non-recoverable Cu).Productora, located in the coastal range of northern Chile, is a magmatic-hydrothermal tourmaline breccia-hosted, structurally controlled Cu-Au-Mo deposit hosted by a thick sequence of Jurassic rhyodacitic volcanic rocks. North and north-west striking fault sets control the distribution of mineralised breccias. Alteration is widespread, complex and pervasive. Hypogene alteration assemblages range in composition from distal magnetite-amphibole, to sodic-calcic, to sodic, to phyllic, to proximal potassic. Low-temperature advanced argillic assemblages are locally juxtaposed next to proximal high-temperature K-feldspar-tourmaline assemblages. The dominant hypogene Cu phase is chalcopyrite.A simple Cu species classification scheme based on sequential leach data and S per cent was devised to account for non-recoverable Cu (ie non-sulfide Cu), which is insoluble in weak acids. Through machine learning, a proxy for this Cu species classification scheme was developed based on: depth, Ca per cent, Cu per cent, Fe per cent, K per cent, Mn ppm, S per cent and Ln(Cu/S) plus logged regolith class, thus allowing classification to be extended to areas of the deposit where no sequential leach data are available. The modelled data has been used to generate deposit-wide 3D models for Cu species classification.The validity of the proxy Cu species classification model is being tested against the results of flotation analysis. Initial results indicate that geochemical proxies can be used to successfully predict Cu species class and provide a high density of classification data.CITATION:Escolme, A, Berry, R and Hunt, J, 2016. Predicting Cu Species Classification Using Geochemistry at the Productora Cu-Au-Mo Deposit, Chile, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 113–118 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By A Turichshev

The synthetic rock mass (SRM) approach for modelling jointed and veined rock has been at the forefront of caving geomechanics research for years. A well-constructed and calibrated SRM model can capture the full rock behaviour at a macroscopic scale. Traditionally, SRM technology employed bonded particle models (BPM) due to their ability to model rock’s response to loading without prior specification of behaviour. The SRM modelling process requires the BPM to simulate intact rock and the subsequent introduction of fractures or veins by changing bonding characteristics between the particles. However, bonded particle materials have difficulty reproducing both the compressive and tensile strengths of intact rock. This and other limitations of BPM have been the driving force in exploring the potential of grain-based (2D) and bonded block (3D) models (BBM).This paper reports on recent work exploring the applicability of both BPMs and BBMs in 3D to the modelling of intact rock. The advantages and limitations of both BPMs and BBMs are addressed based on the results of numerical simulations using the PFC3D and 3DEC distinct element codes. The preliminary results suggest that BBMs are better suited for simulating intact rock behaviour than BPMs. Ongoing work aims to better qualify the applicability of BBMs under different conditions. This has significant implications for our understanding of rock mass behaviour in a caving environment.CITATION:Turichshev, A and Hadjigeorgiou, J, 2016. Simulating intact rock behaviour using bonded particle and bonded block models, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 453–460 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J Hadjigeorgiou, T R. Stacey

A ground support system is a combination of individual reinforcement and surface support elements that work together to retain and contain the rock mass. The various elements are subjected to external loads and to interactive loading between individual ground support system components. This paper focuses on the challenges in determining the capacity and behaviour of mesh, recognizing that installed mesh can be subjected to several loading mechanisms. Field observations from underground hard rock mines demonstrate that there are multiple types of damage and modes of failure of mesh. However, these are difficult to reproduce in a laboratory environment. A critical review has shown that existing mesh laboratory testing rigs reproduce very limited loading conditions that may not be representative of underground conditions. This has significant implications in quantifying and extrapolating the performance of mesh to ground conditions. CITATION:Hadjigeorgiou, J and Stacey, T R, 2018. Challenges in determining the capacity of mesh, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 280–290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By D H MACKENZIE

In common with several great orebodies and mineral camps around the world Broken Hill has been the subject of state-of-the-art technical and scientific scrutiny during its long working life. During the early years geological interest in Broken Hill tended to be directed at the body for its intrinsic scientific worth, mainly on account of its large size, high grade and wealth of mineral species. For much of the last 60 years the interest has had a more applied motivation, namely, to assist the search for either repetitions in the Broken Hill field or analogues in other terrains. This paper looks at the major changes in geological concepts and exploration techniques applied at Broken Hill and attempts to assess their impact.

Jan 1, 1992

By J T. Carswell

Best practice mine sampling should provide a detailed quantification of all potential sources of error at each stage of sampling, sample preparation and assaying.Quality assurance (QA) should include testing for and quantifying potential sampling errors, and should be the basis for establishing ongoing sampling protocols, should set error limits and define quality control (QC) procedures. QA should be within the framework of Theory of Sampling (TOS) but may not involve the estimation of the sampling constant and the application of Gy’s formula.Best practice QC should be carried out efficiently and in a timely and cost-effective manner with regular reporting against the guidelines established by QA.This paper provides an assessment of, and checklist for, current best practice sampling QA/QC with examples from operating gold mines including the QA/QC of underground (UG) reverse circulation (RC) grade control.CITATION:Carswell, J T, 2017. Best practice sampling QA/QC for gold and base metal mining – including how to assess the applicability of underground reverse circulation grade control sampling, in Proceedings Tenth International Mining Geology Conference 2017, pp 297–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Linge HG, Klauber C

The key element in the carbon-in-pulp process for gold processing is the loading of dissolved Au(CN)2 from solution onto activated carbon. The mechanism and kinetics of this step have been examined by solution adsorption-desorption and X-ray photoelectron spectroscopy for both coconut derived activated carbon and peat-based activated carbon. The results show that these carbon types have the same mechanism and kinetics of adsorption. There is no contribution to the bonding from carbon-oxygen functionalities on the carbon surface, as has been invariably supposed in all previous theories for the mechanism of the reaction. It is shown that Au(CN)Z is reversibly adsorbed intact on and parallel to the graphitic planes of the carbon with the formation of a weak carbon-gold n-donor bond. The kinetic measurement of carbon gold loading reactivity is discussed and use of the Murdoch equation for this test is critically assessed.

Jan 1, 1989

By Y Li, B Shen, S Zhang

Jointed rock mass is often encountered in rock engineering and its stability has always been a major concern in underground engineering. To analyze the stress characteristics and their variations in jointed rocks, in this study, a new concept of sub-instability stage before rock failure is defined, and a new experimental method is used to investigate interaction between defects and intact rock of the jointed rock mass during the subinstability stage., Firstly, external characteristics of stress and failure mode of the whole jointed rock are investigated systematically by conducting uniaxial compression tests on red sandstone samples with a set of preexisting open flaws of different sizes, and the interactive damage of intact parts and defects in the subinstability stage was further studied. Secondly, rock-like material samples made of bonded plaster blocks were tested and internal data from stress sensor between the strong and weak segments were collected. The transforming processes from independent activity of the individual segment to overall interactive movement of jointed rock before the unstable failure were analysed. The test results indicated that the subinstability stage marked the beginning of interactive failure between the intact rock and defects. In the early subinstability stage, the relatively intact parts bore most of the load in a jointed rock mass, and the defects were damaged firstly which caused high strain around it. The areas of high strain increase rapidly, extending and migrating, causing damage to the intact parts. In the later sub-instability stage, the interaction effect reached its maximum, and a large number of cracks appeared in the intact rock and they propagated and coalesced. Intact parts experienced rapid failure and then the jointed rock failed. The experimental method used in this paper to identify the sub-instability stage could be used to identify failure precursors of jointed rock masses and to develop technology for disaster prevention in rock engineering. CITATION:Zhang, S, Shen, B and Li, Y, 2018. Experimental studies on interactive failure characteristics of jointed rock, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 453–461 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By A Murphy, D Lauder, J Miranda

Minera Alumbrera Limited operates the Alumbrera concentrator, treating a nominal 80 000 tpd of porphyry gold/copper ore. It is located in Argentina, 1200 km north-west of Buenos Aires in Catamarca Province, at an elevation of 2550 m above sea level. Treatment facilities consist of crushing, SAG and primary ball mill grinding circuits, rougher flotation, ball mill regrinding, gravity recovery and cleaner flotation. It is one of only a small number of concentrators in the world, which uses Jameson Cells alone for cleaner circuit flotation. Plant design was started in June 1995, with commissioning commencing in July 1997. Following a successful ramping up to design tonnages and recoveries, a number of options were reviewed to improve gold and copper recoveries. This paper concentrates on a detailed size by size flotation recovery project, commenced in May 1999. Utilising optical microscopy, scanning electron microscopy and analysis of surface chemistry it has allowed losses by size fraction to be quantified and options for enhanced recoveries to be developed. Coupled with extensive circuit surveys it has also provided an insight into previously unknown properties of Jameson Cell operation. Among these are unique residence time and bubble formation reactions to reagent and pulp flow variations, which has permitted a number of novel changes to the operation to maximise capacity and recovery.

Jan 1, 2000

By S K. Michelic, N Preisser

For certain applications, steels have to feature a very distinct and well-defined level of cleanness in terms of the number and composition of non-metallic inclusions. Therefore, one crucial aspect of steelmaking is removing and controlling said non-metallic inclusions during the process. Particle removal during ladle refining comprises three stages, namely: 1. Flotation 2. Transport through the steel/slag interface 3. Dissolution of the particle in the slag. Only if all three stages are completed the particle can be considered as fully removed from the steel melt which, in turn, leads to the slag being one of the most influential parameters for inclusion removal and control. Depending on the composition of the particles and the slag, the dissolution can be controlled by different mechanisms. This study focuses on the diffusion-controlled dissolution of solid oxidic particles in slags. For this, a model of particle dissolution has been developed. For modelling diffusion, either the differential equation following Fick’s second law can be solved, or an analytical solution to this equation valid for stationary interfaces can be used. Both approaches allow for calculations of concentration profiles of the dissolving species in surrounding slag. From this, the mass flux can be derived, which finally leads to calculating the boundary layer velocity due to considerations of mass balance. In this work, both methods as well as results of dissolution experiments using High Temperature Confocal Scanning Laser Microscopy are compared. This research aims to provide a framework for diffusion-based dissolution modelling in further expanding the understanding of particle dissolution in secondary metallurgy.

Aug 21, 2024

By K Karmawan, T Casten

The PT Freeport Indonesiaæs Deep Ore Zone (DOZ) copper deposit is located in the province of Irian-Jaya, Indonesia. Currently, a block cave mine is being developed around this deposit. Production is scheduled to start the fourth-quarter of year 2000 and to ramp up to 25 000 tpd by year 2003. The air quantity requirement for this mine is equal to 780 m3/s. To supply this quantity, the mine will require five centrifugal fans (one 450 and four 750 kW fans). This study summarises the technical aspects related to the installation and commissioning of two of these fans. The fans were installed on the surface in parallel arrangement with two others. Each has a design capacity of 240 m3/s of air at 2.2 kPa of static pressure. The study presents the installation details from the underground shaft excavation and portal development through fan testing and commissioning. It also presents the results of a monitoring system that was installed to determine the fan duties.

Jan 1, 2000

By S Larbi-Bram, F Shi, E Manlapig

Mining companies have recognised that characterisation of particle breakage plays an essential role in the design and optimisation of comminution circuits. Recently the JKMRC comminution research team has developed a new breakage model incorporating the effect of particle size, and a new breakage characterisation testing device, called the JK Rotary Breakage Tester (JKRBT), which allows rapid testing of particle breakage under high energy single impact and low energy repetitive impact conditions. The latter is believed to be the dominant breakage mechanism in AG/SAG mills. Existing devices, such as the JKMRC Drop Weight Tester, are not suitable for performing repetitive impacts since they are too time consuming. Positive feedback received from mining company sponsors to the new technology has prompted the JKMRC to further validate the device and the model through a formalised experimental test program on professionally designed and manufactured JKRBT machines. The first JKRBT was installed at the Anglo Research laboratory in Johannesburg in March 2007 and four more major mining companies will participate in the project in 2008, with commercial release expected in early 2009. The JKRBT has the potential to revolutionise ore testing, with applications in laboratory impact breakage characterisation of rock samples, drill cores, coal and other materials. It also stands poised to significantly advance the process control of comminution circuits since it is readily adaptable to on-line ore hardness measurement. Can any mine afford to miss out on this technology?

Jan 1, 2008

By Cloutier JY, Quinn P, LeClerc A, Dube G, Agar GE

Gold dissolution by cyanide requires the presence of oxygen which is usually supplied by sparging compressed air into the gold containing slurry. For those ores that contain certain obnoxious substances that consume oxygen, maintaining the required minimum level of dissolved oxygen can be troublesome. One of the most economical solutions to the problem of low dissolved oxygen, especially in plants that have air compressors installed, is to enhance the rate of oxygen mass transfer. The oxygen mass transfer rate was measured in a two phase system using two different sparger arrangements, and with addition of a frother that is known to reduce the bubble size produced by the sparger. The common sparger system was shown to be inefficient compared with a readily available but under utilised method of gas dispersion which introduces air directly below the reactor turbine. Transfer of this technology to an operating plant confirmed the beneficial effect of the improved sparger system. The addition of the frother did decrease the bubble size, but it also reduced the oxygen mass transfer rate.

Jan 1, 1993

By J-P Franzidis

A technique for determining the recovery of attached particles across the froth phase in flotation that relies on measuring the rate at which bubble-particle aggregates enter the froth is used to investigate the selectivity of attached particles across the froth phase. Combining these measurements with those of other techniques for determining the froth recovery of attached particles provides an insight into the different subprocesses of particle rejection in the froth phase. The results of experiments conducted in a 3 m3 Outokumpu tank cell show that the detachment of particles from aggregates in the froth phase occurs largely at the pulp-froth interface. In particular it is shown that the pulp-froth interface selectively detaches particles from aggregates according to their physical attributes.

Jan 1, 2005

By T Huynh, V Matanitobua, J Zheng, B N. Noller, J C. Ng, H H. Harris

A risk assessment was undertaken of the aquatic ecosystem and bioaccumulation of metals and metalloids in fish at the Leichhardt River, Mount Isa, Queensland. Residual contamination of metals and metalloids in Leichhardt River sediment was assessed and arose from mine practices using river discharge in the 1940s. The ecological risk assessment of sediments involved comparison of the concentrations of heavy metals and arsenic with those of the ANZECC/ARMCANZ (2000) Interim Sediment Quality Guidelines (ISQG). Results indicated that all sites including the background site exceeded one or both the ISQG-high and ISQG-low trigger values based on total concentrations. A lesser number of sites exceeded the ISQG-low trigger values following the 1 M hydrochloric acid extract step, which was used as an indication of bioavailability. An additional risk from particulate matter in river sediment is that acute human toxicity from the consumption of fish contaminated with metals and metalloids is unlikely. The potential risk was assessed by comparing with the maximum levels set by FSANZ (2010) for fish consumption by children and adults. In general, the liver of the fish have higher heavy metal and metalloid concentrations compared to the muscle. Frequent or regular consumption of fish from the Leichhardt River that exceed maximum levels (ML) of heavy metals and metalloids is not recommended. Risk analysis showed that an adult can consume up to 5 kg of fish fillets every day from fish caught at the man-made Lake Moondarra downstream on Leichhardt River and still be within safe consumption levels whilst a child can eat up to 1 kg daily.CITATION:Noller, B N, Ng, J C, Matanitobua, V, Harris, H H, Zheng, J and Huynh, T, ?2014. Assessment of ecotoxicology and health risk from bioaccumulation in fish of heavy metals and metalloids from historical mine practices in the Leichhardt River, Queensland, Australia, in Proceedings Life-of-Mine 2014 , pp 337–348 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By G M. Volkmann

Pipe umbrella systems have effectively been used as an additional support system in the working area in weak ground conditions during the last decades. Thus, a considerable number of applications accounts in urban tunnelling with shallow overburden. However, this support system is also successfully used when a tunnel alignment crosses fault zones, sediments, moraines or talus with overburdens from shallow to deep. The pipe umbrella support system itself is termed differently worldwide – synonyms are canopy tube umbrella method, umbrella arch method, or long fore-poling method.One main reason for the increase in application is that this support system closes cost-effectively the gap between reasonable, normal supported tunnels and tunnels supported with more expensive special techniques like horizontal jet-grouting or ground freezing. By using this system, many projects can be built more cost effective without decreasing the common level of safety.The pipe umbrella construction method is pretty young, so the knowledge about this system has been intensely researched in the last decade. This led to an enormous increase in understanding the interaction between support system and surrounding ground, the mode of action, and the important details for construction.Pipe umbrella support systems are applied in difficult ground conditions, so a special developed measurement arrangement was used to observe deformations ahead of the working face during tunnelling. The evaluation of collected data sets identifi ed that cased-drilling systems have clear advantages compared to predrilling systems during the installation process in weak ground conditions. This may become important depending on project requirements, so this difference must be considered in design as well as in the tender document specifications.

Mar 8, 2011

By C Zhang, G Si, J Oh, X Zhu

The presence of rock joints has a huge impact on the strength, deformability, and permeability of fractured rock masses by providing surfaces of weakness on which further deformation are more prone to occur, and by serving as the major channels of water flow due to low matrix permeability. In earlier studies, water flow-through rock joints is often assumed as laminar flow between two ideal smooth parallel plates, and the well-known cubic law was derived and widely used to characterise the hydraulic behaviour of rock joints. However, natural rock fractures are irregular and of spatially varied aperture. Thus, the concept of equivalent hydraulic aperture was introduced to modify the cubic law. Numerous works have been conducted on the relation between hydraulic aperture and mechanical aperture incorporating various geometrical parameters. The surface roughness is one of the most sensitive factors for water flow-through rock joints. The aperture distributions are irregular in natural roughed fractures relative to the parallel plates. Barton et al (1985) and Olsson and Barton (2001) incorporated the joint roughness coefficient JRC in evaluating hydraulic aperture and proposed an empirical equation based on fluid flow tests. However, their equations do not conform to the dimensional consistency. Many other researchers (Zimmerman and Bodvarsson, 1996; Xiong et al, 2011; Li et al, 2019) considered aperture distributions in their equations. But the aperture distributions change during shear was always neglected. The contact of rock joints also has a significant impact on the hydro-mechanical behaviour of rock joint, since fluid tends to flow-through a rough joint along connected channels while bypassing the contact obstacles with tortuosity. Nonetheless, previous research mostly considered joint roughness or aperture changes based on 2D joint profiles, while the contact and tortuosity based on 3D surfaces were often overlooked. Only a few works have been made on quantifying the effect of contact area on flow behaviour (Walsh, 1981; Zimmerman et al, 1992; Zimmerman and Bodvarsson, 1996; Yeo, 2001), and mostly ignored contact area change induced by shearing and the associated impact on flow behaviour. Summarily, the quantification of fracture geometry effects on water flow in single rock joints still needs further investigation, especially when considering coupled shear-flow processes. This paper, therefore, aims to study the impacts of contact area and aperture distributions of the single rock joint on the flow behaviour. The evolutions of contact area and aperture distributions induced by shear are considered. Then, an improved model for estimating the hydraulic aperture with the mechanical aperture incorporating the above factors is developed. Finally, a series of shear and shear-flow tests are conducted on artificial joint samples and the model performance is verified by comparing against the results of experimental tests.

Nov 29, 2022