Search Documents

By L Smith, R Beckie

An intermediate scale (8 m + 8 m + 5 m high) constructed waste rock pile experiment was built upon a contiguous grid of 16 gravity drainage lysimeters to investigate the flow of water in unsaturated waste rock. Average net infiltration to the uncovered waste rock pile is 55 per cent of precipitation. Large rainfall events have net infiltration of 55 per cent to 85 per cent. Net infiltration estimates range from 23 to 120 per cent of precipitation between lysimeters. Small-scale lysimeters of less than 4 m2 area are shown to be poor predictors of net infiltration for uncovered waste rock. The appropriate size for lysimeters increases with increasing flow rate. The residence time distribution has an estimated median value of 3.0 to 3.9 years under average infiltration conditions. Water flows within the fine grained matrix, within larger pores (macropores), and in matrix free areas of the pile. In situ tracer concentrations vary between pore sizes, and between spatially distinct areas of the pile, indicating water geochemistry may also be variable. Water samples collected from in situ soil water samplers are dominated by the most mobile water fractions. In situ measurements of water content and matric suction are compared to the measured outflow. The data indicate the focusing of flow in spatially distinct areas can make in situ instrumentation a poor (non-conservative) predictor of volumetric water flow.

Jan 1, 2003

By G R Ryan

Dissatisfied with conventional wet processing methods for alluvial deposits, Resource Trend Pty Ltd of Cairns set out to develop a better process. After comprehensive investigation of existing dry techniques the principals have now developed a rotary dry concentrator that can handle the fine-grained fraction of alluvial deposits as well as the coarse. Four of these units have been mounted on an integrated towable treatment plant which has been in successful commercial operation for four years in northern Queensland. A second plant is now under construction for use in the United States. Grades of less than 0.2 g/lcm have been profitably mined at throughputs of about 80 cubic metres per hour and 85 per cent availability. The operation runs round the clock with an establishment of four. Major benefits, apart from lower capital and operating costs, are environmental. Ore is picked up, treated, and replaced in its original mixed condition within 25 m of its initial location. Rehabilitation is completed almost immediately behind the plant as it advances, leaving no slimes dams, coarse stockpiles, or haul roads. In 1993 the company won a Premier's Award for Environmental Excellence in the Queensland Mining Industry. The principal disadvantage is moisture, and the company is now actively seeking deposits in the deserts of the world. In Queensland mining is normally possible only for six months of the year.

Jan 1, 1994

The effects of detonation of downlines and downline-booster systems on lodse-poured charges of 94% porous prilled ammonium nitrate/6% fuel oil (AN/FO) were determined. Detonation stability was indicated by the initiation-failure pattern of detonating fuse witness lines located at intervals along the charge. Steel tubing was used as the confining medium. Charge diameters (d) varied between 2-21/32 and 8.1/8 in. and specific charge weights (w) of downlines between 4.0 and 93.2gr/ft. The axes of charge and downline were colinear. The minimum value of w required to cause initiation of AN/FO increased with d. When initiated by a downline only, the charge'underwentlowòorder detonation. When downline-booster systems are used, the detonation wave in the downline cuts all equatorial planes in the charge before the detonation wave in the surrounding AN/FO. If the downline itself does not cause initiation, therefore, the explosive ahead of the main detonation wave is crushed, and hence desensitised, by the radially-expanding compression wave and gases generated by the downline. In a given equatorial plane, the fraction gftharge undergoing detonation decreases with an increase in the booster-plane distance. The longitudinal limit of nation increases significantly with d, but surprisingly little with a decrease in w. In the presence of a downline, the blasting performance of AN/FO charged _

Jan 1, 1970

A laminar-flow furnace technique was used to study the combustion of 37-53 µm size fraction of Woodlawn copper concentrate containing 7.4 per cent zinc, 5.0 per cent lead and 22.5 per cent copper. Factors studied included the effect of time, temperature and the distribution of volatile elements between the panicles and the fume. Air was used for most of the work but a few tests were carried out using 1 per cent oxygen in nitrogen. Chemical analysis, X-ray diffraction, and scanning electron and optical microscopy of polished sections were used to characterize the reaction products.When the concentrate was combusted at low temperatures (800-900°C), the fume was rich in lead. At higher temperatures, this was diluled by increasing amounts of zinc and copper. 70 per cent of the zinc, 60 per cent of the lead and 40 per cent of the copper were found in the fume after oxidation at 1400°C. Lead, zinc and copper were present in the fume as anglesite (PbSO4), zincite (ZnO) and cuprite (Cu2O) respectively. The major phases present in the panicles were magnetite (Fe3O4) and/or cuprospinel (CuFe2O4), with some zincite and cuprite.Elemental copper was found in the particles oxidized in 1 per cent oxygen. Possible vapour species responsible for the vaporization are discussed.

Jan 1, 1985

The HYC mineral deposit at McArthur River is about 1.5 kilometres long by 1.0 kilometres wide and 55 metres thick, and contains 227 000 000 tonnes of ore of average grade 9.2% Zn, 4.1% Pb and 41 g/t Ag. Major studies have been carried out continuously since 1955 over the deposit and in the general region. This work is continuing. A small underground mine was developed by driving a decline tunnel to intersect the mineralization 80m below the surface. This provided a fully representative sample of the total deposit unaffected by weathering or oxidation, and was available for the major test program carried out in a pilot plant built to determine the full metallurgical charac- teristics of the ore. The pilot plant operations followed investigations by research institutions, both in Australia and overseas, into the problems of this ultra-fine grained ore. The ultra-fine grained nature of the ore required grinding to an average size of 95% passing 37 micro metres or 400 Tyler mesh. A major feasibility and environmental report was submitted to the government covering all aspects of a development program. The geological, engineering, metal- lurgical, economic, cultural and environmental submissions contained in this report were studied by external consult- ants employed by the government, who agreed with the conclusions that the McArthur HYC deposit is at present Uneconomic.

Jan 1, 1984

An efficient stores organisation is essential for an efficient undertaking. Unless the stores organisation is able to meet the requirements of its requisitioners promptly and economically, the undertaking as a whole cannot function efficiently.Delays or errors in supply of material, or substitution due to lack of material availability from the stores are costly and must be eliminated. This then makes the objective of a store, to supply on demand at the cheapest possible price, those items of stock which it is organised to carry, also to procure as quickly as possible and at the lowest price those special items required which are not normally carried in stock. To do this it is necessary to set up a stores organisation consistent with the size and requirements of the undertaking. Stores organisations vary with the nature of the undertaking they are designed to serve. In the case of the Broken Hill Associated Smelters Pty. Ltd., an organisation has been established to meet the operating and maintenance requirements of the Port Pirie Works. These embrace the particularly wide range 0:1; activities associated with roasting" blast furnacing and refining the lead concentrates from the Broken Hill Mines in a continuous metallurgical process producing a variety of refined metals; also many associated activities including power production and engineering maintenance and construction.

Jan 1, 1951

The structure and tectonic setting has had a strong influence on gold mineralisation at the Porgera gold deposit. Here, the structural controls on the mineralisation at Porgera are discussed and placed in a regional tectonic context. The Porgera gold deposit is related to the emplacement of the Porgera Intrusive Complex. Prior to intrusive emplacement at Porgera, Papua New Guinea was affected by a major fold and thrust episode which occurred in response to arc-continent collision in the Late Miocene. After crustal shortening the region experienced a relaxation of compression which is expressed in the deformation accompanying mineralisation at Porgera. The first stage of mineralisation (stage I) is hosted by extension fractures, and is spatially associated with exposed intrusive stocks. A later episode of mineralisation (stage II) is hosted by the faults and fractures of the Roamane Fault Zone, which was active as a dip-slip normal fault during stage II mineralisation. Therefore a change in the tectonic environment from shortening to extensional tectonics can be seen at Porgera before and during mineralisation. Rapid fault-slip during stage II mineralisation may have aided high-grade gold mineralisation by subjecting hydrothermal fluids to changes in pressure, temperature, fluid-fluid and fluid-rock interaction. Uplift to form the highlands of Papua New Guinea occurred after mineralisation and was largely complete by 4.0 Ma.

Jan 1, 1995

Characterising the weight percentage of each mineral in base metal ores is an integral part of assessing the quality of an ore in terms of its processing properties. The Rietveld method, which uses X-ray diffraction data, has been applied to routinely quantify the minerals in lead/zinc and copper ores from Mount Isa Mines Limited and supergene copper ores from Ernest Henry Mining as well as their related products from the concentrators. The Rietveld method has been tested by comparing Rietveld mineral data with a standard sample with known mineral weight percentages and comparing Rietveld mineral data with mineral data calculated from elemental assays where the element only exists in one mineral such as lead in galena. Where this latter situation does not occur, the Rietveld method has been checked with both elemental and optical microscope data. In all cases, there is a good correspondence between the Rietveld data and the data it was checked against with absolute differences generally in the range of 0.5 to 3 wt per cent. The Rietveld method generally quantifies all minerals occurring over 1 wt per cent in one analysis and is less expensive and more routine compared to traditional methods such as optical microscope point counting. The Rietveld method can be applied to many stages of the mining cycle such as exploration, feasibility studies, mining, minerals processing and for environmental studies.

Jan 1, 1998

The Tavua Power Proprietary Ltd. was created in 1936 for the purpose of supplying electric power, compressed air and water to the mining field.The original share capital was subscribed on a two-third:one-third basis by the Emperor Gold Mining Company Ltd. and Loloma (Fiji) Gold Mines, N.L. In 1940, Fiji Mines Development Ltd. (later changed to Dolphin Mines Ltd.) was admitted as a shareholder, and, in 1950, a further change occurred. The present shareholding in the Company is as follows:A central power station was decided upon to reticulate power and compressed air over the whole field and building commenced in May 1936.The original plant comprised three Belliss and Morcom diesel generating sets 770 b.h.p. 525 kW 3,300 V, 3 phase, 50 cycle; one Belliss and Morcom diesel compressor set 2,09'0 cu. ft. of free air per min. at 90 lb. gauge 300 r.p.m., and two small Ruston-Holman diesel compressor sets each of 525 cu. ft. capacity taken over from Loloma (Fiji) Gold Mines, N.L., and the then existing Koroere Gold Mining Company.BuildingThe original building was 130 ft. long by 47 ft. wide with an elevated switchgear annex on the west side from which a clear view of the engine room is available.

Jan 1, 1953

By M J. Pascoe

The performance of 460 stope surfaces at WMC ResourcesÆ Olympic Dam Operation (ODO) has been used to investigate the confidence that can be placed in the Stability Graph Method for design of stope dimensions. A detailed database of stope performance and ground condition information was established for each stope. The database contains all the required stability graph information as well as other factors thought to influence stability, such as discrete major structures, poor shape and exposure time. The performance of each stope surface was quantified by calculating Equivalent Linear Overbreak/Slough (ELOS). The performance of stope walls and crowns was plotted on the supported and unsupported case history stability graphs. Based on this information an ODO design limit of HR = 3.3 x NÆ0.33 has been suggested for stope walls. Walls that plotted above this line were 80 per cent stable, 20 per cent unstable and zero per cent failed. Below the line 60 per cent were stable, 30 per cent unstable and ten per cent failed. Supported crowns that are flat or arched in shape and are not within the influence of major structures can be designed in the stability graphÆs æstable zoneÆ with a strong likelihood of stability. The Stability Graph Method did not reliably predict the performance of unsupported crowns at ODO.

Jan 1, 2005

The Writer's knowledge of this region began in 1912, while he was with the Geological Survey of South Australia, and, investigated the principles governing the occurrence of fresh and saline ground waters in the area then being opened for closer settlement by the railways under construction from Port Lincoln.These field investigatons for water were extensive rather than intensive, but other examinations covered certain mineral aspects. The Writer also has' had the benefit in the preparation of this paper, of later work done by others, as well as of the monumental earlier work in South Australia by the late H. Y. L. Brown.AREAThe area dealt with, approximately 21,000 square miles, lies to the south of the latitude of Port Augusta.TOPOGRAPHYAs a whole the region is one of low relief, but the Olinthus Range, west of Cowell and north of Cleve, reaches an elevation of 2,000ft., while there is als0 a high area west of Port Lincoln and Tumby Bay. At the north end of the region the Gawler Ranges are formed by the dissection of a thick sheet of felspar porphyry extending over two degrees of longitude, by a width of 20 to 70 miles, with fairly uniform maximum elevations of the undissected portions of the order of 1,000 ft. above sea level. South of the Gawler Ranges are many isolated ridges up to 1,000ft. in height, generally sedimentary and trend...

Jan 1, 1951

A summary of the more important work by previous workers is followed by brief descriptions of the rock formations and regional structure. Type examples of the various forms of mineralization are described and the conclusion is drawn that there has been one main period of ore formation, namely, during the "Viti Revolution" in the mid or late Miocene.INTRODUCTIONThe Crown Colony of Fiji is comprised of a group of some 250 islands situated between latitude 160 sand 21 0 S and longitudes 1770 E and 1780 w: By far the greater, part of the total area, 7,083 sq. miles, is contained within the two main islands, Viti Levu 4,053 sq. miles, and Vanua Levu 2,128 sq. miles, and it is to these that most geologists have directed their studies. The most detailed work has been in the Tavua Basin, north coast of Viti Levu, centering about the mining town of Vatukoula and the geology of this area forms the subject of a separate paper by Blatchford (this volume p. 13).The present contribution summarizes geological knowledge of Fiji, at the time of writing (Feb. 1952), with particular reference to the known mineralIzation, but excluding the Tavua Basin. For general descriptions of Fiji's topography reference should be made to the recent works of Derrick and Dunkin.PREVIOUS WORKERSPeriod 1840-1930Prior to the gold rush of the early 1930s the visiting geologists concerned themselves in the main with the struc...

Jan 1, 1953

By Stewart C. A

The Northparkes copper-gold project is being developed in Central Western New South Wales approximately 30 km NNW of the town of Parkes and approximately 350 km west of Newcastle. The project is a joint venture between North Limited (80 per cent) and the Sumitomo Group (20 per cent). North is the manager. The basis of the project is three copper-gold orebodies, the northern two of which are being mined by conventional open cut methods with the third and largest orebody at the southern end of the lease to be mined by block caving. A fourth mineralised body has been identified in the centre of the lease. While further evaluation of this deposit is required it would appear to be amenable to block caving. Oxide caps of gold ore and copper-gold ore over-lie the two northern orebodies. Development commenced with the construction of a carbon-in-pulp (CIP) plant to treat the oxide gold ore. Construction of a flotation plant to treat oxide copper-gold ore and sulphide copper-gold ore is underway. When full-scale operation is achieved late in 1996 the plant will treat 5.0 million tonnes of ore per year of which 1.1 million tonnes will be open cut ore and 3.9 million tonnes will be block cave ore. In terms of annual ore tonnage the underground mine will be the largest metalliferous mine in New South Wales and the second largest in Australia.

Jan 1, 1995

By C Aldrich

In this paper, the use of topology preserving projections (Sammon maps) and neural networks are considered as a basis for the construction of multivariate statistical process control charts for a semi-autogenous grinding circuit on a gold plant. Comminution circuits are often operated in a quasi-steady state mode, where the mills tend to move rapidly from one state to another. This makes them difficult to monitor by conventional means designed for continuous steady state processes. As a first step, process data reflecting normal operating conditions are mapped with SammonÆs algorithm. Only one feature is extracted at a time and each mapping is captured by a neural network model to allow online application. Reverse neural network models are used to reconstruct the data prior to the extraction of subsequent features from the data residuals. The ensemble of neural network models can then be used for both fault detection and identification. The approach compared favourable with both linear and non-linear principal component models. It was able to detect two simulated fault conditions both with a reliability of 100 per cent, as opposed to 57.8 per cent and 95.2 per cent detected by an approach based on the use of linear principal component analysis and 84.1 per cent and 98.0 per cent detected by an approach based on non-linear principal components extracted with auto-associative neural networks.

Jan 1, 2007

By R H. Knight

Uncertainty in prediction and modelling of geological (physical) ore continuity in geometrically complex ore deposits is a key risk factor in mining. Reducing geometric uncertainty of hard-boundary ore/waste contacts and related geological features improves the efficiency of local mineral resource estimation and reserve calculation, mine/stope planning, ore control and in-mine exploration. Detailed underground mapping of serial-level drives provides a continuous record of the characteristics and contact configuration of ore, as well as crucial ore-related geological features that are required to resolve geometrical variability when closely spaced drilling proves inadequate or is cost-prohibitive. The mapping-based approach described in this paper re-establishes the focus on the geology of the orebody by incorporating high-value, detailed geologic mine mapping information. Mapped ore-related configurations and relationships, recorded on a succession of faces or on a series of levels, provide the basis for 3D interpolation and extrapolation of the local geologic continuity of an orebody. Correlative points representing locations of key ore-related geologic features on each face or level are linked by 3D polylines or trajectories forming a coherent geometrical framework. The coherent progression of geometric changes mapped by these trajectories reveals the overall ‘dynamic’ of the geometrical framework, as well as the spatial tendencies of its geological constituents. Distinct sets of ore control trajectories are selected from within the framework and are used in the construction of alternative geological ore continuity models. As mining proceeds, alternative models are evaluated, and are then either refined or rejected. The geometrical framework is used to evaluate theoretical models and practical heuristics, focus exploration targeting and inform and guide all aspects of mine geology in active mines. This approach also lends itself to analysis of global ore continuity in the re-evaluation of mature or abandoned mines. Its use is particularly effective in geometrically complex orebodies such as the West Branch orebody and the orebodies of No 2 mine of the Balmat-Edwards-Pierrepont zinc district, which are used to illustrate the method. CITATION:Knight, R H, 2014. A mapping-based approach to geological continuity prediction using examples from the Balmat-Edwards-Pierrepont Zinc District, St Lawrence County, New York, USA, in Proceedings Ninth International Mining Geology Conference 2014 , pp 65–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By D L. Kennedy

Many aspects of the physical layout of manufacturing plants and storage facilities for explosives are governed by so-called quantity-distances tables. Both the British and the American tables were originally derived from an analysis of the injuries and the building damage documented by an early 20th century compilation of significant accidental explosions. However, progressive changes in explosive process technology and in building techniques have reduced the relevance of much of this historic data set. Extensive scientific research has been conducted over recent decades to characterise the potential injuries and damage from accidental explosions under more modern conditions. This presentation will showcase some of this research.**This is an abstract only. No paper was provided for this abstract**

Nov 8, 2011

The approvals process for a major cut-back is not a simple exercise when a mine is located alongside the community. Kalgoorlie Consolidated Gold Mines (KCGM) has been through an extensive process of government, JV owner and community consultation to ensure that necessary permitting processes and detailed studies have been completed to allow this six year extension to the open pit mine life to be achieved. With the Kalgoorlie Boulder community being on the doorstep of the mine, it is critical to ensure that the operation runs smoothly and complies to the license conditions to achieve the full value of the Golden Pike cut-back, and leave behind a sustainable legacy for the local community. This is an ABSTRACT ONLY no paper was prepared for this presentation.

Jun 1, 2010

Designing and constructing OxianaÆs Sepon gold and copper operations in one of the most remote areas in Laos has been a great achievement; one which was recognised by the engineering industryÆs highest accolade û the Australian Engineering Excellence Award in 2005. The developing nation of Laos has no previous mining or heavy industrial experience, but the support of the Lao Government and a remarkable Lao workforce has enabled the project to be developed and operate as well as it would anywhere else in the world.When making a decision to invest offshore, several geophysical and jurisdictional criteria need to be considered. Laos offers unparalleled prospectivity, a central location with growing infrastructure, a ready workforce and a developing but supportive regulatory regime. In addition, the Sepon copper project has exceptional characteristics, including its high grades, location near the surface, leachable qualities, access to hydropower and the ability to produce cathodes on site. These attributes and its location in the centre of a region hungry for resources contributes to the projectÆs excellent economics.

Jan 1, 2006

By A Dix

Fire suppression systems are but one of the many technologies currently available to manage operational tunnel risks. However, the actual reasons for their use are often shrouded in mischievous discussions of the marketing variety.The international tunnelling community still stands divided on the merits (or otherwise) of fire suppression systems. For some the debate focuses on their cost compared to the theoretical benefits they bring to human safety.Long standing concerns about their potential adverse effects in an emergency are often at odds with the experience from tunnels which use them. High installation and operational costs are cited as reasons not to use them, yet toll road operators and insurers increasingly use them as a risk mitigation strategy for toll revenue protection.Fact or fiction, myth or reality, should such systems be seriously entertained or are they just another expensive gadget in the escalating array of expensive toys for modern tunnels? Ultimately this presentation argues that they have their place as a risk mitigation measure to achieve a range of objectives. The exact circumstances for their use ultimately fashioning their design and operational characteristics. This is an abstract only. No paper was prepared for this abstract.

Mar 8, 2011

By S Gray

Based on the 2021 Volume 5 State of PlayTM mining survey of key executives and board members in the mining sector, the key responses to ‘Which of the following technologies will have the biggest impact on mining in the next 15 years?’, were ‘Sensing and Data’ followed by ‘AI and Analytics’. From the early 1970s it would have been unlikely to predict the level of sensing and automation introduced to the broad industrial sector. No better example is the automobile industry where the combination of technological advances and external drivers (such as emissions control) have driven an incredible rate of change. The introduction of sensing, data, AI, and automation in the mining industry is just ramping up. Until now our energy efficiency, environmental footprint, labour shortage, skills, and safety have not been challenged by stakeholders in the way we are seeing market forces develop today. In order to address these challenges, we need to look back to the automobile industry and learn their lessons to accelerate our application of digital capability, analysis, AI and automation This is critical, particularly as access to skilled human resources becomes more difficult. An example of how this can be achieved in a gold processing plant utilising the latest real-time sensing technologies is the ‘Carbon Scout’ developed by Curtin University, and OLGA developed by CSIRO, which are both online technologies, coupled together with Gekko’s ‘Neon’ digital platform to achieve a fully automated real-time gold processing system.

Aug 24, 2022