Search Documents

By Grant JR, McKavanagh BM, Dear SJ

A geophysical technique of rock mass assessment for engineering purposes is being investigated and shows positive correlation with direct structural logging and mapping techniques for the detection of major geological features. The technique is cross-hole acoustic surveying incorporating high speed signal averaging, with a maximum hole separation in excess of 30 metres in hard unfractured rock masses. The bulk of the field test work was carried out in open stopes in the copper ore bodies of Mount Isa Mines Limited. The investigation forms part of an integrated study of blasting in mining, aiming for fragmentation control through blast design modification. The rock quality factor, Q, is presented as a blasting index and can be determined for a significant portion of a production stope.

Jan 1, 1981

There exist many formulae for designing coal pillars. However, when applied to a given set of mining parameters, they lead to different pillar sizes and factors of safety. From the subsidence point of view, the pillars designed as protection pillars not only have to be stable, but also have to limit subsidence over them to a level acceptable to the structure being protected. The subsidence over a pillar of given width to height ratio depends upon the mining depth. A pillar may be stable, but the subsidence over it may be quite large and unacceptable for the structure. In many cases even though pillars may yield, they support the undermined strata and reduce surface subsidence. In addition, the yielding pillars eliminate peaks and troughs in the surface subsidence profile and reduce ground strains. In a given situation, whether a pillar yields or not depends primarily upon its width in relation to mining depth.

Jan 1, 1992

Gold mineralisation at the Enterprise Mine, 230 km south of Darwin, occurs within folded and metamorphosed sediments of the Lower Proterozoic Burrell Creek Formation adjacent to the Cullen Granite. The mineralised zone, which occupies an area of approximately 800 m x 300 m is local- ised by a moderately tight, upright symmetrical anticline which plunges shallowly southwards. The anticline has been disrupted by numerous faults on which the maximum movement is 40 m. Gold is associated with quartz and sul- phide veins which are present as saddle reefs, inter-reef veins and fault controlled reefs. it occurs within the veins or their alteration haloes, either as free gold (2 - 50 per cent of total gold content) or intimately associated with sulphides, principally arsenopyrite and Pyrrhotite.

Jan 1, 1984

The phenomenon of Instantaneous Outbursts, although not new to Australia, was sharply drawn to the attention of the local coal-mining industry by two isolated fatal occurrences on widely separated fields, both late in 1954. An outburst is the eruption of apparently solid coal from the face, aided by vast quantities of gas released from the coal, as the coal fails under mining stresses additional to its natural stressing.The gases involved are principally methane and carbon dioxide. The various factors which combine to produce outburst conditions range from external factors such as stresses arising from depth of cover and other causes, to inherent factors such as strength of coal,and its capacity to retain gases (sorption). Of the localities where instantaneous outbursts occur the Gard Basin in Southern France has had the greatest number and the most serious occurrences. By contrast, local outbursts have been minor.Experimental work into some influencing factors has been carried out by various overseas authorities and some research has been accomplished in Australia. Practices used in some overseas areas to improve safety of working are largely empirical, as are the local rules and recommendations for work in affected areas.The appearance of further outburst areas is anticipated as mining becomes more extensive and deeper.INTRODUCTION"Instantaneous Outbursts" can be described as violent eruptions of coal from the solid accompanied by considerable gas evolution. The projected coal is usually of small size, and a high proportion is pulverized, and may be carried and deposited over great distances by the gases, liberated from the outburst. This outburst coal is of bituminous to anthracitic rank, and the gas involved is essentially methane or carbon dioxide, or a mixture of both. Outbursts involving carbon dioxide are usually more violent and dangerous. The phenomenon is relatively unusual, being confined to probably sixteen known areas in the entire world, these areas comprising only portion of the coalfields in which they occur. Usually only one or two mines on each field are affected.

Jan 1, 1958

The reduction in man's contribution to the Greenhouse effect will only be achieved by a number of small steps. Some steps will absorb carbon dioxide (CO2) from the atmosphere in slightly greater quantities, others will reduce the amount of carbon dioxide generated. This paper deals with the reduction of carbon dioxide by improving the combustion efficiency of petroleum fuels. Until recently most reductions in fuel consumption and air pollution have been brought about through mechanical adjustments to combustion equipment. Since the development of tetraethyl lead, little has been done to chemically modify combustion reactions to improve fuel efficiency or reduce emissions. During the past five years Australian laboratory and field trials with ferrous picrate treatment have demonstrated significant and economic gains in the combustion efficiency of diesel fuels. These studies have revealed that even under ideal conditions in diesel engines, carbon monoxide (CO) momentarily saturates the combustion chamber. This state reduces combustion rates, peak pressure and power and increases the risk of pollution. Theoretical, laboratory and field data are presented which support the mechanism by which the ferrous catalyst accelerates the oxidation of CO to the terminal CO2 thus reducing fuel consumption and the undesirable combustion products accompanying the CO saturation of combustion environments. While this paper deals principally with diesel fuels commonly used in mining operations, the catalytic effect of the ferrous ion is also shown to significantly reduce fuel consumption by petrol engines thereby promising a means to reduce the much larger contributions to the Greenhouse gases by automobiles.

Jan 1, 1989

By Russell F. M

Following the accident in the Peterson section of Mufulira mine in September, 1970, a method had to be found of extracting up to 300 000 tonnes of ore per month from this area without inducing caving. Sandfill mining methods were chosen, necessitating a plant capable of producing both cemented and uncemented fill on a large scale. The paper covers the design and construction of this sandplant which is thought to be unique for its size, as it incorporates three 3 000 tonne capacity settled storage silos, a 500 tonne capacity cement silo, mixing tanks and a control room situated underground. The plant is designed to handle an aver- age of 440 tonnes per hour with a maximum of 660 tonnes per hour for limited periods, delivering either uncemented fill or cemented fill in proportions varying from 1:6 to 1:30. The instrumentation and equipment necessary to give one man operation of the plant is described and the fill mining methods now in use at Mufulira are briefly outlined.

Jan 1, 1973

The intention of this paper is to examine the practical and technical aspects associated with the measurement of blasting related phenomena. The emphasis is directed towards the acquisition of quantitative data rather than its theoretical interpretation. The application of advanced technologies will require that many more people involved with blasting become familiar with this topic. Against the many other disciplines where measurement may be beneficial, blasting is peculiar on several counts. 1) It must almost always be carried out in the field, and very often in a production environment. 2) Much consideration must be given for the safety of personnel and equipment. 3) The process is dynamic and seldom repeatable. Because the blast process is so dynamic there is little opportunity for direct examination. For this reason measurements are almost universally made using electronic techniques. In this way the event can be captured faithfully as it occurs and later examined in detail, after the fact. It is obvious that some familiarity with these electronic techniques is a necessary ingredient for successful blast monitoring.

Jan 1, 1990

By May P. M

The role of chemical speciation in alkaline cyanide solutions is discussed by reference to recent experimental data from the authors' laboratories. It is shown that serious gaps exist in our present knowledge of the thermodynamics of cyanide complexes in solution. Nevertheless, using the available data and the JESS suite of computer programs it has been possible to develop a simplified chemical speciation model for alkaline cyanide solutions under conditions relevant to the gold extraction process. Some possible implications of the model for plant operations are Discussed.

Jan 1, 1991

By Hamblyn S

Oakbridge, in combination with its joint venture partner, Nippon Steel of Japan, is expanding its Bulga underground and open cut mines to meet the growing demand for coal in the Asian market. Expansion works underway will see the Bulga underground mine become a world leader in underground productivity, the introduction of a high capacity dragline into the open cut mine (largest capacity dragline in NSW) as well as a major upgrade of the coal preparation plant (CPP) and coal handling facilities (CHF) to process the increased production. This paper describes the planning and implementation of this major expansion program and highlights the rationale behind some key aspects of the program.

Jan 1, 1995

Comparatively recent Tasmanian legisla tion established a series of rigid control standards for environmental protection just as ma spectacular expansion of the mining industry was nearing completion. Upgrading existing protection to obtain the necessary licence to operate under these new regulations required further major works and involved a considerable outlay of non- productive capital at a time when escalating costs and falling metal prices were straining economic efficiencies to the limit. Late in 1974 a major environmental protection scheme was commissioned by the Electrolytic Zinc Company of Australasia Limited at Rosebery on the West Coast of Tasmania. This 4 million dollar project was specifically developed by the Company ahead of and to meet the new standards for control of total effluents discharged from its zinc-lead -copper-pyrites mine and concentrator.

Jan 1, 1977

By Royle A. G

The paper describes a geostatistical structural analysis of an 80 square mile lease of the Athabasca tar sands. Each step of the analysis is presented with the ultimate objective of condensing the principal structural characteristics of the chosen regionalised variables into the opera- tional form of the variogram model. The variogram model is then used to form kriged local and global estimates, with the corresponding estimation errors.

Jan 1, 1977

By Dight P. M

The challenge of narrow vein mining is to produce ore with as little dilution as possible, at the least cost -commensurate with the increasing degrees of safety being demanded for mine workers by the modem 'duty of care' legislation. Geotechnical factors play an important, if not overriding, role in these areas. The geotechnical factors cover the complex interaction over a period of time, between the in situ and induced rock stresses, rock structures, rock mass strength and the cable, rock bolt and other ground support members. In the Archaean schist belt areas where many of our narrow vein mines occur the pre-mining in situ rock stresses are commonly significantly higher than the overburden stresses. These are concentrated in areas beneath previous open pits and may be highly concentrated in the pillars and abutments of stopes on narrow veins. The presence of high in situ stresses may be suspected from the appearance of drill cores and underground development long before they become sufficiently concentrated by mining to cause damage or bursts. These initial indications are discussed and modem low cost methods of stress measurement are described. Practical and quick methods of analysing the stress redistribution around scopes and other underground excavations are now available and guidelines for interpreting them in terms of rockmass characteristics, stope stability and support requirements are developed with the object of increasing safety, whilst reducing overall costs and dilution.

Jan 1, 1993

The Boddington Gold Mine orebody is a large tonnage, low grade gold deposit located within the Archaean Saddleback greenstone belt within the south-western region of Western Australia. The orebody consists of laterite caprock (30 per cent) and clays (70 per cent) produced by lateritisation of felsic volcanics and intrusives. The caprock comprises gravel, hardcap and B-zone which have a specific gravity of 1.8, 2.4 and 1.8 respectively. The clay has a specific gravity of 1.5.

Jan 1, 1993

By Misra V. N, Spottiswood D. J

In recent years the column flotation process has gained worldwide acceptance for processing various types of minerals under different circuit configurations. In an age when real prices of many mineral commodities are in decline and mining and labour costs are rising in real terms, it is more important than ever that concentration processes be not only efficient but also cost-effective. The column flotation process can give better metallurgical performance as well as involve lower capital and operating costs compared to conventional mechanical cells.This paper reviews the literature on columns and the effects of various column parameters on performance of the column flotation process. The history and principles of operation of the column flotation process are briefly discussed by way of introduction.

Jan 1, 1995

By Plumridge C. L, Lynch J. E, Forresty R. J

The Amanda Bel Goldfield (new name) is an area of approximately 1000 sq. km centred 65km WSW of Ingham and 150km due east of Kidston (Camel Creek homestead to Ryeburn homestead area). Gold mineralisation has been located in tightly folded sediments of the Silurian Greenvale Formation as well as in the Early Devonian Kangaroo Hills Formation and the Early Carboniferous Clarke River Formation. The area is traversed by a major NW-SE structural corridor, with many of the numerous basaltic, andesitic and rhyolitic dykes of the region sharing a similar trend. So far fourteen gold-bearing zones have been located, all of which are new discoveries delineated by bulk cyanide leach sampling and subsequent geological reconnaissance. The region has undergone three periods of deformation with gold mineralisation introduced syn-D1, post D1 - pre D , syn-D and post-D2/D , thereby revealing an involved metall~genic history. Mineralisation types include Sb, Sb-Au, Sb-Au-As, Sb-Au-As (-Pb-Zn) and Au-As. Minor occurrences of W, Pb-Zn-Ag and Pb-Zn-Ag-As-Sn are also present as are alluvial (deep lead) tin Drosoects.

Jan 1, 1989

By Phelan JM

Poor selectivity in the separation of two sulphides generally arises because the flotation characteristics of the coarse sizes of the valuable mineral and finer sizes of non-valuable minerals are identical. Separat- ing the pulp into two size fractions at a specifically determined cut size and conditioning each size fraction with its own optimum reagent addi- tion is known to be helpful in improving such selectivity problems. The performance of the zinc section of the complex ore circuit at Wood- lawn Mines has been analysed in detail. The selective recovery of zinc was found to be a problem in zinc/pyrite separation. However, atypi- cally, the separation problem was between coarse zinc and coarse, not finer, pyrite. In spite of this the use of separate conditioning has effected significant improvements in rougher concentrate. Selectivity (and hence grade), overall recovery and flotation rate have all been enhanced. Dis- appointingly, coarse zinc recovery was not increased but, with careful optimization, this might be achieved without sacrificing the gains already realized. The technique of separate conditioning clearly has general application in other circuits where selectivity is a significant problem.

Jan 1, 1988

The sulphide ores of the Kalgoorlie goldfield have long been looked upon as' refractory, involving special metallurgical treatment. For many years two kinds of treatment have been practised-(l) wet treatment, including fine grinding, amalgamation or concentration of the free gold, concentration of the sulphide minerals with subsequent roasting and cyanidation, and cyanidation or bromo-cyanidation of the residue from the concentrating operation; (2) dry-crushing of the ore and roasting the whole of thecrushed ore, amalgamation of the gold in the calcine during fine grading, followed by cyanidation. The wet treatment was advanced a stage further when, in 1929, the Lake View and Star Ltd. adopted large scale flotation. As a consequence, however, further metallurgical problems were introduced. This paper covers the investigation, ,of one of the most prominent of these problems.Flotation preceded by strakes was satisfactory to a point.The flotation concentrate consisted largely of auriferous pyrite and tellurides, and the gangue minerals in the concentrate were practically barren.Several sources of loss of gold values were, however, found to be associated with this circuit, viz.-(a) There was the loss of gold in the flotation tailing.(b) Loss by dusting during roasting of the flotation concentrate.(c) Loss of gold in the cyanided residue.

Jan 1, 1937

The completion of the Hot Strip Mill at the Port Kembla works of Australian Iron & Steel Ltd., makes possible the production of steel plates and wide strip of a quality and in quantities not possible previously in Australia, and will also enable the production of tinplate to be undertaken in this country.The site chosen for the mill was a mud fiat underlain by a hard stone bottom at 5, to 801 feet below the surface; and a total area of one hundred acres was reclaimed to a level of 20 feet above the original surface.Three adjoining buildings were constructed to house the slab receiving yard, mill equipment and electric drive, together with the plate finishing line.After slabs have been heated to 2250°F at a rate of 90 tons per hour, they are transferred to the vertical scale breaker which is the first stand in the hot roughing mill. Here the primary furnace scale is first cracked and then blasted off by high velocity water descaling sprays.The next stand is the horizontal scale l;Jreaker, where any remaining primary scale is broken and then blasted off. After descaling, the slabs pass to the broadside mill, where short slabs are turned and rolled on broad side for wide plate.The next step is a slab squeezer which squares up the edges after broadsiding ready for the reversing mill. This is the finishing stand for plate and the last roughing stand for strip, which then passes to the finishing mill.The hot strip finishing mill consists of six stands with a maximum finishing speed of 2,230 feet per minute. Strip is cooled for coiling by water sprays on a hot run table and then coiled on a mandrel type downcoiler, from whence coils of hot strip are weighed and transferred by conveyor to the coil storage building.Plates are transferred from the reversing mill to the plate finishing line where operations consist of levelling, inspection, branding, cutting to width and length:INTRODUCTIONDue'to the increasing production of cars, refrigerators, washing machines and similar consumer goods in Australia, together with the increased requirements of galvanised iron...

Jan 1, 1956

The tankhouse of the electrolytic zinc plant at Nordenham is operating with a very high operating efficiency of 99 per cent. This has been achieved not only by strict control of the quality of the zinc sulphate cell feed solution but also by all the improvements in housekeeping in the tankhouse developed during the past years: aluminium cathode specification, cathode stripping cycle, edge strips, copper contacts, anode isolators, cell cleaning, fittings and washing devices. During 1987 to 1992 the casting department was completely remodelled in order to improve the quality of the zinc products, the safety of the operations and the flexibility. The remodelling includes the enlargement of the area for the casting shop, the storage buildings and the five casting lines on the same ground level. New lines for alloying products and for SHG25 kg zinc ingots have been constructed. The line for galvanising products has new equipment in some parts and the other lines have been modified.

Jan 1, 1993

By Needham RS

Hydrothermal mineral deposits are the dominant mineral deposit type in the Cullen Mineral Field, and have been important sources of tin, tungsten gold, silver-lead, zinc and copper. The deposits are mostly in north to northwest-trend- ing shear zones, and are confined to Early Proterozoic contact metamorphosed metasediments or synorogenic to postorogenic granitoids. The distribution of the vein-type deposits with- in the contact aureole defines a district-scale metal zonation of uranium closest to granitoid, through tungsten, copper, tin, silver-lead to gold with increasing distance from granitoid contacts. This zonation probably reflects de- creasing temperatures within the contact aureole during granitoid emplacement, and at the time of generation of a variety of metal-bearing fluids. A magmatic source for some of the metals is indicated by the positive spatial relationship between uranium, tungsten, copper and silver-lead deposits and granitoids abundant in those metals. There is little evidence for any such relation- ship for tin and gold deposits, except for an association of some tin deposits with tin-enriched mafic rocks. Most of the granitoids with anomalous metal values are late stage highly fractionated leuco- granitic phases forming younger plutons peripheral to the main body of the Cullen Batholith, They probably form cusps connected to the main body at shallow depths.

Jan 1, 1984