Search Documents

By Lonie W. M

The rapid development of the Australian steel industry over the past twenty years has greatly increased the demand for coking coal from the collieries owned by the Broken Hill Proprietary Co. Ltd. and Australian Iron & Steel Ltd. This in turn has called for an intensive and continuous programme of colliery expansion and new colliery development, along with the reorganization and modernization of existing collieries.This paper presents a general description of the factors involved and the techniques used in planning modern colliery development for the steel industry.PRELIMINARY GEOLOGICAL INVESTIGATIONSIn any colliery development, preliminary geological investigations require a detailed and practical knowledge of the geology and characteristics of the coal-field as a whole. In the early stages of the investigations, probably the most valuable information is obtained from outside the particular area under review, rather than within it, and unless the geology of the coal-field is understood, the projection of the known information into the unknown area cannot be carried out with certainty.Because development of the coal seams from the outcrops has been an apparently simple matter and not subject to the risks involved in deep mine development, the geology of the New South Wales. coal-fields has not received the attention that major mineral resources warrant.Only the most accessible regions of the coal measures have been generally prospected, while the potential areas remain...

Jan 1, 1957

By D J. Black

The process of longwall coal extraction coal causes fractures in the overlying and underlying strata and these fractures become pathways for gas released from adjacent coal seams to flow into the mine workings and contaminate the ventilation air. If the rate of gas emission exceeds the diluting capacity of the ventilation air, the gas concentration will increase and exceed the statutory limit resulting in production delays.All potential gas sources within the planned mining area, including coal seams located above and below the working seam, should be identified and sufficient gas data collected and used to determine the specific gas emission from each gas source. Gas reservoir and emission modelling is recommended to determine specific gas emission and changes in gas emission from individual sources over the planned mining area. Accurate gas reservoir and emission modelling provides the information required to accurately design gas drainage programs to effectively manage gas emissions and minimise the risk of ‘gas-outs’.Given the increasing occurrence of incidents of gas concentration in ventilation air exceeding the 2.0 per cent statutory limit and changes to mine plans to avoid ‘difficult-to-drain’ areas, it is apparent that many operations are not effectively utilising gas reservoir and emission modelling to identify high gas emission areas and are not completing sufficient gas drainage in advance of planned mining.The process of gas reservoir and emission modelling to support gas drainage design to control tailgate gas concentration and fugitive emissions is presented and discussed.CITATION:Black, D J, 2017. Gas reservoir and emission modelling to evaluate gas drainage to control tailgate gas concentration and fugitive emissions, in Proceedings Australian Mine Vent Conference 2017, pp 65–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By A B. Christie, S C. Cox

Effective land-use planning requires accurate knowledge of mineral resource potential. Mineral companies during reconnaissance exploration, feasibility investigations and mine development also use this type of analysis. The Institute of Geological and Nuclear Sciences is undertaking a two-year project reviewing the resource potential of the West Coast of the South Island of New Zealand. Spatial prospectivity models have been developed as part of this resource assessment process, using computer based statistical pattern recognition techniques to delineate areas that are prospective for mineral deposits and to test deposit genesis models. Digital GIS data-sets of mineral occurrence were correlated against geology and exploration information. The distribution of mesotherrnal shear zone gold deposits in the Reefton Goldfield, were examined against geological data-sets from both the regional (QMAP) and local prospect-scale mapping. Weights of evidence analysis generated a correlation matrix that highlights relationships and degrees of association that might otherwise not normally be recognised.   Mesothermal shear zone gold deposits have strong positive spatial correlations with Greenland Group host rocks and areas with moderate to high quartz vein densities; moderate-strong positive correlation with regions <500 m from folds, with regions <600 m from faults and five to eight kilometres from granite contacts; moderate correlations with Ntrending fault and fold segments; and no/weak/poor correlations with fault intersections, fold-fault intersections, bends in regional structures and magnetic and radiometric data. The regional and prospect scale data sets give different results, with the more detailed prospect scale mapping giving generally better correlations. This emphasises the value of detailed geological mapping in the exploration process.   Maps generated by prospectivity modelling consistently highlighted areas of known mineralisation and generate targets where follow-up investigation is warranted. The prospectivity per unit area provides a measurable value that should change as new information comes to hand and, in addition to highlighting targets, can be used to measure the impact of increased exploration expenditure and assess the effectiveness of exploration investment.

Jan 1, 2001

The Kalgoorlie Tailings Retreatment Project (or "Kaltails") involves the reclamation and retreatment of approximately 50 million tonnes of gold tailing situated on the Golden Mile at Kalgoorlie, Western Australia. Tailing is reclaimed and retreated at the rate of 42 million tonnes per annum. The project is a Joint Venture between Poseidon Limited and Gold Corporation, with Poseidon being the major participant (90%) and manager of the operation through its wholly owned subsidiary Kaltails Mining Services Pty Ltd. The marginal nature of the tailing retreatment project dictated that a detailed feasibility study be undertaken. Extensive sampling and metallurgical testing of the tailing permitted the development of an optimum economic processing route. A sensitivity analysis undertaken as part of the feasibility study indicated the project to be very sensitive to gold price and unit operating cost variations, and relatively insensitive to capital cost variations.

Jan 1, 1990

Ore samples generally require preparation before analysis. Serious problems can occur with contamination degradation and particle size effects. Both grinding element contammation and sample cross contamination havebeen bound to be related to sample hardness and operator technique. For best results with minerals relevant to the steel industry, the use of Siebtechnik-type mills required a combination of careful planning, short grinding periods and intermediate sieving of the sample. The results may be extended to most mineral, rock, and refractory sample preparabons.

Jan 1, 1978

High Pressure Grinding Rolls Scale-Up and Experiences

Sep 13, 2010

The Wongawilli system of mining has been in use for over 30 years and has enabled high production rates and acceptable extraction ratios to be achieved in seams less than 4 m in thickness. A modification of the Wongawilli system has been developed to permit the use of a continuous miner and mobile equipment to extract a coal seam 6 m thick. Following physical and mathematical model studies the new mining method is now undergoing field trials at Collinsville, Queensland. Progress of the field trials to date has achieved 99 per cent extraction of the upper slice by remote control operation of the continuous miner and established the feasibility of installing resin grouted wooden dowels in the coal floor to reinforce the coal septum. The method is explained in the text. Monitoring of the goaf gases as an early indication of spontaneous combustion has been incorporated in the mining cycle by placement of tubes in the goaf as the face retreats and continuous analysis of the goaf gases made at the surface by the National Coal Board tube bundle monitoring system.

Jan 1, 1980

By D Kilkenny

Underground contractors in the mining industry must be prepared to take a position at the forefront of innovation of equipment and work methods in order to maintain a competitive advantage over in-house operations and remain relevant. Innovative concepts such as split-feed development jumbos, high capacity trucks and loader guidance systems were implemented by contractors to stay ahead of ‘the pack’. All of these are now common across the industry.The demands of regular participation in competitive tendering coupled with aggressive fleet depreciation, means contractors tend to have more communication and opportunities to work with equipment suppliers than mine owners. Therefore, they are more likely to influence equipment design and product directions. They also have a unique opportunity to assist in trialling new concepts and technologies across a wide variety of operating conditions rather than being restricted to one mine.In addition, as a ‘guest’ on a mine site, mining contractors do not have the luxury of creating the environment for their preferred systems, rather they must have the capacity to adapt their technology to suit the offered environment at a particular mine. This leads to a pursuit of adaptive technologies that can be implemented selectively and seamlessly without excessive disturbance rather than ‘all-of-mine’ systems. These incremental innovations then become available for use across the mining industry where they can add value as ‘bolt-on systems’ to existing operations.Mining contractors, therefore, act as the bellwether for industry practices and equipment. However, in order to maintain their position they must engage industry stakeholders to deliver practical, innovative and cost-effective technologies that add value and result in an improved bottom line for all. This paper uses case study material to illustrate how the Byrnecut Group has approached innovation and how the theory of Disruptive Technology applies to underground mining innovation.CITATION:Kilkenny, D, 2017. Innovation in mining – a contractor’s role, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 59–68 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By R L. Braithwaite

Mesothermal quartz lodes in Paleozoic Greenland Group metasediments of the Reefton area have produced 67 t of gold up to 1951, and recent exploration has identified new gold resources in several deposits, including the largest past producers, Blackwater and Globe Progress. The metasediments consist of alternating sandstone and argillite, metamorphosed to lower greenschist facies and hydrothermally altered near the quartz lodes. We examined and sampled drill core from four prospects, Globe Progress, General Gordon, Merrijigs and Blackwater, to determine the mineralogical and geochemical characteristics of hydrothermal alteration in the sandstone units. The sandstones are feldspathic litharenites averaging Q65, FlO and R25, with detrital grains of quartz, feldspar, rock fragments, muscovite, biotite (mostly altered to chlorite), and trace quantities of graphite, apatite, zircon, tourmaline and titanite. Hydrothermal alteration has developed a secondary mineral assemblage of K-mica (muscovite, sericite and illite), carbonate, chlorite, pyrite, arsenopyrite and limonite. The abundance of secondary chlorite is greater at Blackwater than at the other locations studied. Features in the sediments associated with increasing hydrothermal alteration towards quartz lodes include, the development and increasing intensity of colour bleaching and carbonate spotting, increasing quantities of disseminated pyrite and arsenopyrite, and the appearance and increasing quantity and size of thin carbonate, quartz and sulphide veins. This is accompanied by increasing concentrations of sulphur, arsenic and antimony as shown in assays, and of volatiles (loss on ignition) and iron as seen in XRF analyses. We were unable to identify consistent trends in the behaviour of potassium, sodium, and calcium that are exhibited by similar mesothermal quartz lode deposits inVictoria, Australia.

Jan 1, 1998

The development and introduction of a preventive maintenance scheme in the coke ovens department, coal preparation section, of The Broken Hill Proprietary Co. Ltd., Newcastle steelworks, is described together with its operation and the results achieved during the first 12 months.'fhe scheme consists essentially of an engineering analysis of the plant to establish maintenance schedules, and to record the details on reference cards.Items are reviewed progressively and a weekly work schedule is prepared, from which work orders are passed on to the maintenance foremen. These foremen in turn originate action orders and issue inspection sheets as required. Results are then reported back to the maintenance planner and used to revise norms, practices, and cycles.INTRODUCTIONWhat is maintenance? Some people consider maintenance to be the work involved in putting things together again after they have fallen apart. The author regards it as the mechanical care and repair of plant machinery and equipment to keep it operating in sound mechanical condition, without undue interference with production processes.Maintenance may be organized or haphazard, and, too often, what has been fondly imagined to be nicely controlled and organized maintenance proves, under pressure, to be more correctly described as haphazard. Haphazard maintenance deals with breakdowns as they occur, and frequently finds itself confronted with more breakdowns than can be handled. Even organized maintenance, if not based on sound planning, can, at times, be found in a chaotic state, because of unexpected and unanticipated breakdown.Properly planned and scheduled maintenance permits an orderly and controlled approach to the problem of maintain...

Jan 1, 1961

This paper describes a mobile laboratory developed specifically for nickel prospecting, and which was designed to be operated by sub-professional staff in remote areas independently of established laboratories. An atomic absorption spectrophotometric procedure was used to determine nickel, cobalt, lead, zinc, and copper ID latentIc and sulphIde samples, with a detection limit better than 25 µg/g for all elements. The procedure was applicable to both soil and drill samples and the accuracy of the procedure, which was ±5 per cent relative at the 1,000 µg/g level was sufficient for the preliminary assessment of mineralized samples and the control of drilling operations. The analytical procedure and the means taken to ensure the necessary reproductibility and accuracy are described. One operator can carry out 400 elemental determinations per 8-hr day at an approximate cdst of 6 cents per elemental determination. The results are returned within a single day, a factor which can contribute materially to the efficiency of drilling operations.

Jan 1, 1970

By D Vickers, N C. Fowke

The reduction of geological risk for planning of high production longwall faces is essential. Geological and geophysical techniques applied at Huntly West Mine before 1989 were unable to reduce the geological risk to an acceptable level. The success of a trial long-hole directional drilling programme at Huntly West Mine (Fowke et al, 1989) has encouraged the Coal Corporation of New Zealand to use the technology long-term, for seam definition. Initial drilling in 1989 completed a total of 3543 metres, with the longest borehole length being 369 metres (limited by number of rods available). A major re-interpretation of seam structure resulted from the drilling, which was able to fill in seam details between surface exploration boreholes. The undulating thick seam conditions at the mine require a refinement of drilling strategies used overseas. Long-hole directional drilling also displays potential for inseam gas drainage. Gas flows of the order of 1000 L/min were initially indicated in individual boreholes. Other gas parameters of the seam have been studied by Beamish et al (1991), and highlight the significance of the natural gas resource in the Huntly Coalfield.   The continued development of drilling technology will be of major benefit sustainable development, particularly in policy.

Jan 1, 1991

By P Williams, S Flynn, R Birchfield, R Simcock, R Toft, P Comeskey

Direct transfer, or community translocation, comprises salvage and replacement of intact æsodsÆ of vegetation together with underlying soil. It has been applied to New Zealand mine sites restoration of native grasslands, wetlands, scrub lands, and forest. It is an equivalent technique to æinstant lawn or tree gardenÆ, commonly used in urban landscaping. Two to six m2 scoops of vegetation, with up to 0.7 m of soil attached, and including root plates of trees and shrubs, are relocated from stripped areas ahead of mining to sites prepared for restoration. Direct transfer uses hydraulic excavators or face shovels and dump trucks, possibly with the aid of bulldozers and other earthmoving machinery. The main advantages of direct transfer, compared with sowing or planting systems for mine site restoration, are the recycling of plant and soil materials which were often wasted by burying under overburden materials, a significantly faster revegetation process, and restoration of the whole ecosystem (plants, animals, birds, invertebrates, and microbes). The main disadvantages are higher costs of stripping and dumping, a greater degree of machine operator skill required, and scheduling becomes critically important. To illustrate the key principles, this paper gives examples of successes and failures of the technique for a variety of New Zealand mining situations. Direct transfer has been successful for a range of communities, from fern wetland and sub-alpine tussock grasslands to 5 m-tall beech forest under storey and seral shrub land, and from temperate to sub-alpine climates. Successful examples show both rapid recovery of indigenous vegetative cover and conservation of habitat for birds and invertebrates. Failures have resulted from excessive death of plants because of inadequate soil salvage depths, acidic leachates, inappropriate handling of stripped sods by inexperienced machinery operators, or prolonged drought conditions immediately following relocation. Change in plant species composition has occurred where clumps of vegetation are too far apart, or shifted plants were too small - in both cases invasive weeds have smothered the original vegetation. Changes in hydrology can also have significant impacts. Our experience indicates that the advantages of direct transfer far outweigh the disadvantages and is now used as the preferred restoration method, where practicable, at mines where it has been trialled.

Jan 1, 2000

FROM time to time articles have appeared in the technical press on the interesting subject of surface combustion. The theoretical part of the problem has, for practical purposes, received ample consideration in those articles, but the number of practical applications of surface combustion referred to has generally been very small.It is the writer's object to review some recent developments in surface combustion, and also to try to arrive at an estimate of its advantages and possibilities. It is not necessary for this purpose to dilate upon the phenomenon of surface combustion itself. Many interesting things have been said on the subject by Pro£. W. A. Bone, of Leeds, to whose researches the recent developments are largely due. A few illustrations may make clear what is meant by surface combustion.Prof. Bone, in an experiment, took a platinum crucible, which he heated in the flame of a Meker-burner. Then he turned the gas off for a second, and, opening the stop-cock again, allowed the combustible mixture to impinge upon the crucible, thetemperature of which was still well below the ignition temperature of the gas. Although no flame was visible at this stage, it was soon clear that, nevertheless, the gas and air had continued to combine, as the crucible would attain a red heat after a few seconds.Another instance of surface combustion was shown by a Mr. Fletcher, in 1882. He placed an iron ball, weighing 3 lb., on a slab of fireclay, heated it for a few seconds with a blow-pipe, and blew the flame out, leaving the gas-mixture still...

Jan 1, 1915

When we are beset with the economic problems the world faces today, we are always inclined to look at the shorter term future. Today I would like to take a long-term view of our industry, project historical demands for our products into the future and discuss opportunities for our members. Perhaps we could firstly look at the long-term demand trends for our metals. If I tend to use non ferrous metals as a basis for my figures it is because this data is more readily available to me. I am sure that most other products of our industry show similar trends.

Jan 1, 1992

By I Halikia, T Lilis

Lead smelter slags, produced during the last century in quantities ofmillions of tonnes at Lavrion, Greece, have recently been used in theconstruction of Lavrion harbour. In order to evaluate the geochemicalstability of slags and assess their environmental impact on the aquatic environment, a detailed study on lead leachability under conditions that simulate subsea environments was carried out. Leaching experiments using magnesium chloride solutions under mild temperature conditions were conducted and the effect of main parameters on lead solubility was examined. Furthermore, kinetic analysis on the experimental results was performed. Based on the results, lead dissolution increases by increasing the reaction time, magnesium chloride concentration in the bulk solution and temperature, whereas it decreases by increasing the slags particle size. The reaction order was found to be approximately 0.5 at the initial extraction stages and the activation energy value from the Arrhenius plot was estimated to 29.8 KJ/mole. Diagnostic equations applied to all the experimental data reveal that lead dissolution is mainly controlled by diffusion through the ferrosilicate matrix of the slag particles, which is in accordance with the low activation energy value. The JanderÆs diffusion equation [1-(1-a)1/3]2=kt was proposed as the equation representing the reaction of lead dissolution from slags using magnesium chloride solutions.

Jan 1, 1999

By J Williamson, M Griessmann

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Watershed tungsten deposit is located in the Hodgkinson Province of north Queensland, Australia. The deposit is hosted by Siluro-Devonian flysch-type meta-sediments of the Hodgkinson Formation, which were subjected to four major deformation events. Mineralisation has occurred syn- to post-D4 and is related to the intrusion of S-type granitoids of the Permian Whypalla Supersuite.Watershed is located within a regional NW–SE-striking melange zone composed of brecciated and intermixed arenites and shales. The major NW–SE-striking Tullah fault zone is situated in close proximity to the east of the deposit.The Watershed deposit occurs within a tightly folded upright anticline with NW-plunging fold axis. The anticline contains a major package of coarse-grained to conglomeratic arenite, which harbours the Watershed mineralisation. Several alteration styles occur within the arenites, of which Fe-poor calc-silicate alteration dominated by clinozoisite/epidote is the most significant. Less widespread but locally important alteration styles comprise garnet-dominated calc-silicate alteration, albitisation and sericitisation. The arenites are enveloped by unmineralised carbonaceous shales and shale breccias.Tungsten mineralisation occurs solely as molybdenum-poor scheelite and can be found as three styles: disseminated mineralisation in calc-silicate altered arenites, vein-style mineralisation with quartz-albite-scheelite veins and minor but high-grade mineralisation in albitised felsic dykes.Contact metamorphic rocks and geophysical data indicate the proximity of an underlying granitic body. It is believed that this granitic body was the main driver of the hydrothermal system generating the Watershed deposit. An early mineralisation stage caused the selective calc-silicate alteration of the arenites, while a second stage caused the vein-style high-grade mineralisation. The folded shales enveloping the arenites worked as an effective barrier that kept the mineralising fluids in a confined rock volume.The scheelite mineralisation at Watershed is open to depth, with a granite-hosted porphyry or greisen-style mineralisation anticipated below the current resource.CITATION:Griessmann, M and Williamson, J, 2015. The calc-silicate-hosted Watershed tungsten deposit, far north Queensland, Australia , in Proceedings PACRIM 2015 Congress, pp 545–550 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Geological hazards such as faulting, basement ridges, and zones of "thin" (< 6 m) coal have a major impact on mining economics of underground operations in Huntly Coalfield. Experience has shown that drillhole-based investigations do not yield sufficiently detailed models of the coal seam to allow management of the planning risks associated with these hazards. Consequently, operational performance is affected by unplanned costs associated with lower productivity, loss of coal reserves, and expensive strata control remedies in problem ground conditions. Huntly Coalfield is a challenging environment for acquisition of good quality seismic reflection data due to the very thick (10-85m) weathering layer. Since 1994, successful acquisition of 2D and 3D data has been achieved through a combination of careful testing of technical parameters and experimental trials prior to committing to production recording. High resolution seismic reflection (HRSR) is proving to be an investigations technique which generates accurate and reliable models of the coal seam and associated structures, such as normal faults and topography of the surface on which the coal seam rests. The HRSR technique has been applied and developed in the Okowhao Sector where Huntly East Mine is developing and extracting coal reserves. Results of a recent 3D survey demonstrate that this technique is capable of revolutionising risk management in mine planning for underground mines in structurally complicated coal deposits.

Jan 1, 1997

By Probert D. H, Wright E. A, Taylor B. L

A general description of the geology of the Southern Coalfield is given. The relationship between the Illawarra Coal Measures, the overlying Triassic and the underlying Upper Marine Series, of Permian age as are the Coal Measures, is briefly explained and thestratigraphy of each is described. The eight coal seams are then treated in slightly more detail as to their thickness, quality, areas of distribution and best occurrences.In the last few years each of the authors has been concerned with one phase or other of the stTucture of the field in detail or in mining operations with the result that it is now possible to name a number of monoclines, anticlines, domes and synclines defined in detail. A minor quantitative study has been made of faults and dykes with regard to form, direction intensity and inter-relationship. It seems probable that with the further collection of data a more detailed study in these matters will be of considerable value to the economy of mining in the Southern Coalfield.

Jan 1, 1958

By Caithness SJ, Heape JMT

Following the discovery by CRA of gold at Mt Kare, and the subsequent 1988-90 gold rush, mechanised mining of the alluvial resource is now being carried by a company jointly owned by CRA (51%) and landowners of the area (49%). Mining is currently being carried out using small gravity processing plants fed by hydraulic excavators. Use of hydraulic mining techniques will be limited to over- coming difficulties related to the high clay content of the material and the soft nature of the bedrock. Current resource estimates suggest that the alluvials will have a mining life of three to four years. During this time, exploration of the hydrothermal gold mineralisation at Mt Kare will be carried out by a wholly-owned company of CRA. It is hoped that this will lead to establishment of an economic primary gold resource.

Jan 1, 1991