Search Documents

By Lu T. K

A new type of rockbolting system, the self drilling rockbolt, has been studied to develop a 'single pass' bolt for use in rockbolt installation in underground engineering. This single pass bolt forms the basis of a Rapid Face Bolting system which will reduce the amount of time spent in securing a roof during the operation of a continuous miner in the development of a panel.The installation efficiency and anchorage tests were performed in the laboratory on the self drilling bolt and the traditional resin anchorage. bolt. The results of both bolts are cmmnared.

Jan 1, 1993

A system for rapid on-line determination of weight percentage coal in slurry and weight percentage ash in coal has been developed at the Julius Kruttschnitt Mineral Research Centre, University of Queensland. The gauging system is suitable for use with coal flotation slurries or slurries having a maximum particle size of about 1 millimeter. The system is based upon measurement of gamma ray transmission; radioisotope sources emitting photons of two widely different energies are employed. The inaccuracies of measurement that would normally result from variable amounts of air entrained in the slurry are substantially reduced by pressurising the slurry to approximately 2MPa (300 psi) using a Mono pump. The equipment can be used to make measurements on more than one slurry stream by pumping streams sequent- ially. The system is being tested at the Peak Downs Mine of the Utah Development Company in Central Queensland. This paper describes the theoretical principles of the gauge design, the experience gained to date in the commissioning of the equipment, including the installation of a PDP 11/03 computer, and the progress made in developing satisfactory interpretations of the gauge count-rate output.

Jan 1, 1978

By Falconer A. J

Two magnetic parameters are proposed as a basis for the assessment of ironsands beneficiation. The parameters are deter- mined for raw sand prior to dredging and for magnetic separator head feed over a production period of five months. The relationships between these parameters and the performance of the magnetic separators are examined to establish the value of magnetic assessment compared with the traditional soluble iron assay method. The results illustrate that the first parameter, true magnetic fraction (TMF), has a value superior to that of soluble iron when relating raw sand grade calculated by tri- angulation to magnet performance. In terms of the relationship between magnet head feed grade and magnet performance, TMF and soluble iron perform equally as assessment parameters. For the ironsands mined during the five month period, the second magnetic assessment parameter, composite fraction (CR), is shown to merely reflect TMF and offers no additional information for assess- Ment. Conclusions are that true magnetic fraction has many advantages over soluble iron in terms of time and cost of determination and that it is a meaningful and reliable parameter upon which to base all calculations relating to the mining and beneficiation of ironsands.

Jan 1, 1980

By Mayer TE

The Granites Goldfield is located 550 km northwest of Alice Springs. Mineralisation was discovered in 1900 and intermittently worked along nine km of strike until the early 1950's, yielding a recorded production of 470 kg of gold. The geological environ- ment, pre-existing exploration drilling results, and an optimistic view on gold, prompted acquisition of the property by North Flinders Mines Limited in 1975. An agreement was signed with the Central Land Council in August 1983 and drilling commenced in the same month. In the past, gold was won from alluvial deposits, rich quartz veins and lower grade, disseminated stratabound mineralisation. The last is contained within a distinctive unit in the Mt. Charles Beds, of the Early Proterozoic Tanami Complex. This informally named "Host Unit" is a metamorphosed, chemical- pelitic sediment. The schist contains variable proportions of amphibole, quartz, garnet, clinopyroxene, carbonate and sulphide, inter- calated with recrystallised chert beds. Free gold occurs in several mineralised horizons within the Host Unit, generally conformably distributed within lithologic bands or at lithologic contacts. The Host Unit occurs within a sequence of metamorphosed pelitic sediments and intermediate volcanics. Although mostly confined to the Host Unit, stratabound gold mineralisation also exists in both Footwall and Hanging Wall Schists, usually within zones displaying certain Host Unit characteristics. The deposits may be loosely categorised as being of banded iron formation (bif) type, although some important differences are noted between them and classical bif type orebodies.

Jan 1, 1984

By Chaves AP

This paper describes an investigation on the surface properties and mechanisms involved in the agglomeration of iron ore. For this purpose, an organic binder (carboxyl-methyl-cellulose (CMC)) was used in substitution of bentonite, the classic binder in iron ore concentrate agglomeration. Recently, a renewed interest of the iron ore producers in Brazil to replace bentonite for an organic binder, because of the economy that can be achieved in the, blast furnace operation. These savings are mainly due to the lower aluminum silicate addition which decreases slag volume and the improved pellet metallurgical properties which have the potential for lowering hot-metal production costs. Also organic binders are effective at lower addition levels, which results in lower storage and transportation costs. It is very important in Brazil because of the vast geographical area since transportation is made mainly by truck. Another advantage of organic binders is that they have low ash contents, and therefore most of the binders bum. off during the pellet firing operation. Previous studies have demonstrated the possibilities of the use of CIVIC, but in addition to its high cost, the pellets presented improper behavior at high temperatures or when prepared with high moisture levels. In the investigation here described, these problems have been solved through the addition of other reagents to CMC.

Jan 1, 1993

By Tarvainen M, Mattila O

Outokumpu Oy has systematically developed the automation of mineral flotation covering the technology of both new devices and control methods, and as a practical result of this effort currently produces two on-stream X-ray analyzers. The Courier 300 system basing on conven- tional X-ray technology is applied to complex or large processes. The newer Minexan 202 dis- tributed probe system based on radioisotope technology is developed mainly for simple or small scale applications. In this paper aspects and experiences of these analyzer systems and their applications for flotation control are discussed with particular reference to the role of the computer

Jan 1, 1977

By Delahey G, Dunne R

At New Celebration Gold Mine the advent of treating primary sulphide ores resulted in decreased gold recoveries of four to ten per cent. The grind coarsened due to an increase in ore hardness and gold in the residue was found to be associated with pyrite. Finer grinding improved recoveries but was impractical as production rates would have decreased to unacceptable levels. An alternative approach that has proved to be viable combines both gravity separation, to recover the coarse gold bearing sulphides, and then regrinding the concentrate in a tower mill prior to releaching in the cyanide leach circuit. The tailings treatment plant was commissioned in December 1990 and details of the first 18 months' operations are Provided.

Jan 1, 1993

The phosphatic overburden of Christmas Island is a lateritic soil and consists dominantly of crandallite and millisite. These minerals are polymorphs of general formula, (Na,K)x Ca2-x (Al, Fe)6 (PO4)4 (OH)10-x (2+x) H2O. Iron occurs only in millisite. Both minerals exhibit similar thermal transformations, dehydroxylating near 600¦C and recrystallizing above 800¦C. Dehydroxylation results in crystal structure collapse but retention of crystal morphology. Ggethite, boehmite and apatite are minor constituents of some-of the phosphatic Soils.

Jan 1, 1971

By Seneviratne SP

The excessive displacement of the seam floor in headings (i.e. roadways) called 'floor-heave' is often experienced in the underground mines of the Southern Coalfield of New South Wales. Apart from interfering with the mining operations, the phenomenon could be detrimental to the stability of the pillars left for support leading to an unpredictable increase in the subsidence of the overlying strata. The latter could pose a serious problem, particularly in the design of partial extraction layouts of mining for areas where subsidence is to be controlled. The susceptibility of the floor of different rock materials and thicknesses in a given `panel and pillar' partial extraction geometry was examined by two- dimensional Finite Element Modelling of the displacements, stresses and failure zones around the excavations. The modelling, assuming elastic behaviour of the materials, indicated that the maximum vertical displacements of the floor increased substantially as the Young's Modulus of the material decreased to less than 7GPa and the thickness of the layer increased. The results also discount the possibility of a properly designed panel and pillar geometry in the Southern Coalfield of New South Wales being unable to adequately control surface subsidence through the pillar, or its core independently of the yielded ribs, penetrating the floor.

Jan 1, 1992

By Clarke RG

Renison Mine was developed as the first all diesel mine in Australia. The foresight of the early planners in committing the Mine to Decline access has paid dividends in the past two decades with Renison Mine establishing itself as one of the most productive underground mines in the world. The excellent productivity has also resulted from the development of mining equipment technology, both on the part of the equipment suppliers and through the coordination of the Mining, Automotive and Technical Design Sections at Renison Mine. Constant improvements in truck and loader design, the design of specific equipment to carry out specialized tasks such as installation of services, scaling and ground support and the conversion to electrically powered equipment have been ongoing at Renison. Currently, larger scale trucks are being investigated for ore and waste haulage due to increased haulage distances and production requirements. It appears as though an articulated low profile truck of around 50 tonnes capacity may provide the short term solution based on the performance data available.

Jan 1, 1982

By P Christen, D R. Ashley, G R. Power

The Ernest Henry Mine is currently a copper-gold open pit operation situated in north-west Queensland, Australia. It is owned and operated by Xstrata Copper with a current throughput of 11 million tonnes per annum; however, open pit operations are scheduled to cease in late 2011. The deposit dips at approximately 45¦ and extends for at least another 400 vertical metres below the final 530 m deep pit design. Resource drilling from 2002 until mid 2008 has enabled an Indicated Mineral Resource to be established to 1000 m below surface. Scoping and prefeasibility studies (PFS) have been completed toward determining if this resource is suitable for underground mining and a feasibility study is currently progressing with a sublevel caving (SLC) concept. This paper briefly describes the process by which the SLC method was selected, conclusions regarding the non-selected methods, and then discusses the optimisation process used to derive the mining plan. The key optimisation parameters include the production drive spacing, level spacing, draw strategy, cut-off grade and production rate. Key risks will then be assessed and economic sensitivities studied. Final sensitivities will use Monte Carlo simulations to improve the transparency of the projectÆs risk profile. The feasibility study (FS) began in March 2008 and this paper describes the main optimisation steps at the time of writing and outlines the plan for study completion through to March 2009.

Jan 1, 2009

By Amusin BZ

The concept of rigid or yielding bolts is discussed based upon support requirements for excavations of equivalent geomechanical behaviour. The concept of equivalent geomechanical behaviour is introduced for comparison purpose where the rock mass properties are varied for a given depth (stress) so that the deformation of the roof without any support remains constant = 300mm. A simple experimental theoretical analysis for a uniform stress field acting on an axi-symmetric excavation is conducted to establish roof bolt requirements under different conditions such as width of a given excavation, time of setting of support etc. Results are presented in graphical forms.

Jan 1, 1992

By Borshoff J, Coles R

The Rum Jungle Uranium Province is lo cated on the western margin of the Pine Creek Geosyncline approximately 60km south of Darwin. Uranium was discovered in the Embayment area (Whites Deposit) in 1949, spurring active ex- ploration and leading to the discovery of the Rum Jungle Creek South Deposit in 1959. With the discovery of the Alligator Rivers Uranium Field, new criteria in the understanding of the controls for mineralization sparked a re- surgence of exploration activities in the Rum Jungle area. Uranerz Australia Pty. Ltd. (UAL) commenced exploration in the area in the late 1970's in joint venture and in its own right. Two domal Archaean granitic complexes, the Rum Jungle and Waterhouse Complexes, domi- nate the area. They are unconformably mantled by Lower Proterozoic sediments metamorphosed to middle to upper greenschist grade. The Lower Proterozoic sediments are unconformably over- lain by remnant blocks of Carpentarian sand- stone, generally preserved in downfaulted blocks. Over a six year period extensive geolo- gical, geochemical and geophysical programs were conducted to reinvestigate previous target areas and locate new prospective zones. Exten- sive shallow bedrock drilling showed that lo- cally the stratigraphic succession is quite variable and cannot always be divided into an ordered succession for correlation with groups and formations established by the Bureau of Mineral Resources (BMR). Deformational events resulting in intraformational recumbent folding and overthrusting also account for repetition of certain lithotypes.

Jan 1, 1984

By Kavetsky A, Scott A

As well as breaking and moving rock, blast energy sets up a seismic wave in the ground which can cause significant damage to rock structures and buildings and disturbance to human occupants. This seismic ground vibration is potentially most damaging when its dominant frequency coincides with the resonant frequency of a structure, leading to high amplification factors between the input ground vibration and the resulting structural response. This paper outlines methods of identifying the resonant frequency of structures. It also describes a practical numerical method for the modification of blast designs to reduce the ground vibration energy in critical frequency ranges. The method is illustrated with two recent case studies.

Jan 1, 1990

By Thompson AG, Cadby GW

The New Austrian Tunnelling Method (NATM) is a proven concept for the safe and economic construction of underground facilities. This is especially true for tunnelling activity where changing ground conditions are often encountered. However, the principles central to the NATM have gained only limited use within Australia, presumably due to the measurement process inter- fering with tunnel driving and the cost associated with instrumentation and interpre- tation expertise. The design and operating principles of two basic instruments are explained together with laboratory simulated test results and suggest- ions for use in an integrated NATM style approach to underground excavation and construc- tion. The two instruments monitor load in rock reinforcement and deformation in rock or primary and secondary linings. The instruments may be fitted with a miniature display module which outputs the measured parameter in engineering units directly. The design of the sensing components allows the instruments to be installed in various configurations suitable for routine performance monitoring, quality control, support element testing or detailed investigations. The display module which reduces the need for instrumenta- tion expertise should suit contractors and allow performance data to be obtained which quickly may be used to modify support procedures to suit ground conditions. When complemented by convergence measurements the devices enable most facets of the NATM to be implemented.

Jan 1, 1987

By Motyka J, Adamczyk AF, Witczak S

A case study of migration of a paper factory fluid wastes, on the distance of 5 km from an underground disposal site to an ore mine is presented. The ore mine in question, situated in SW Poland is pumping 3.5 m3/s (ca 300 000 m3/day) of groundwater, producing a cone of depression about 150 m deep and several kilometers wide. The migration of wastes (pollutant) occurs within the carbonate karstic aquifer of Triassic age. The aquifer is about 100m thick and is characterized by the coefficient of hydraulic conductivity equal to 8 m/day on the average. The results of systematic measurements carried out for 13 years enabled to estimate the mean breakthrough curve of the pollutant. On this basis and taking into account the coefficient of hydraulic conductivity as well as the mean hydraulic gradient between the disposal site and the ore mine, the migration parameters of the polluting material, i.e. the real flow velocity, the effective porosity and the longitudinal disper- sivity have been calculated. As the measurements considered a long migration distance of the pollutant, the obtained hydrodynamic dispersion constant (dispersivity), in the authors opinion, is reliable enough to be applied for regional groundwater calculations, regardless of the "scale effect".

Jan 1, 1988

By Dutton D

In the British coal mining industry, during the last decade, a great deal of environmental monitoring experience was acquired, particularly in the Doncaster Area of the Yorkshire coal- field, which had a long history of spontaneous combustion and gas emission problems. This paper summarises the experience obtained and shows how the introduction and operation of these systems has resulted in improved techniqu- es for fire detection and control. Some of these systems are described in detail with emphasis placed on the uses to which output data are put, and their impact upon management at colliery level. Reference is also made to the problems encountered in the development of such systems and how they were solved. The paper also makes reference to the recent Research and Development work of the NCB's Scientific Department and Mining Res- earch Development Establishment (MRDE), which was directed to the design and application of a range of underground sensors, and so ensured continuing progress in this field. The paper refers briefly to a new comprehensive monitoring unit and an integrated fire detection and data transmitting system which are currently being assessed in the Yorkshire coalfield.

Jan 1, 1983

By A Karrech, G M. Hassan, A Varghese, E Lessing, S Martins

Pumps play a critical role in mining operations, and their energy consumption and environmental impact are significant. This paper addresses the need for a holistic approach to sustainable pump deployment by expanding on previous work presented at IMPC Asia Pacific 2022 and World Mining Congress 2023. The research takes a significant step forward by outlining a structured approach to estimate and demonstrate sustainability tailored for operational slurry pumps. It details the calculation methodologies used to quantify the carbon dioxide emissions from electricity, wear materials and transport, as well as sealing water usage. To enhance practicality and usability, a simplified visual representation—called sustainability metrics—has been developed to monitor overall efficiency. The sustainability metrics consist of the availability, pump efficiency, and water utilisation efficiency. The proposed methodology is integrated with Pumps Condition Monitoring Service to maximise benefits. Three case studies, from iron ore, copper, and nickel operations globally, were employed to evaluate the proposed methodology. The findings demonstrate the critical role of sustainability calculations in understanding pumps operation. These calculations improve awareness of the pump’s role in the sustainability journey and enable effective monitoring. The studies highlight that continuous monitoring paired with effective prescriptive maintenance strategy can significantly reduce power and water consumption while maximising pump availability. The case studies also reveal significant shortcomings in current operational practices and non-optimal maintenance regimes, emphasising the need for practical recommendations to maximise savings and optimise pump performance. In the context of increasing climate change awareness and the imperative for global decarbonisation, this research highlights the necessity of critically assessing methods and operations to drive sustainability in the mining industry. By adopting a holistic approach to sustainable pump deployment, mining operations can effectively reduce their environmental impact while enhancing operational efficiency and economic viability. The proposed methodology and case studies provide valuable insights and practical recommendations for mining companies seeking to achieve sustainable practices and contribute to a decarbonised future.

Sep 1, 2024

By Dyne GD

From experience in the design and operation of power station combustion facilities in most mainland Australian States, involving a wide range of black coals and lignites, and in the specification and procurement of coal supplies for power station use, techniques for the optimisation of coal resource development and power generation utilisation have been developed to ensure compatibility between characteristics of the selected coals and power station design. These techniques include computer data bases for resource data handling and computer simulation of coal-fired boilers for determining coal property cost effects. Data Base Systems allow results of coal analyses to be efficiently handled, to assist in the review of the relevance of resource data to the coal sections proposed to be mined and the coal fractions proposed to be marketed. Data Base Systems also facilitate the marshalling of coal quality data into basic utilisation format to enable a proper utilisation review and analysis of the certainty and scatter of coal properties. Computer simulation of the effects of different coal properties on the capital and operating cost of power stations is achieved by establishing conceptual design parameters of the major items of plant to relate the variations in coal specification to equipment size and type. Variations in power station budget costs can then be determined using the computer model for variations in coal specification.

Jan 1, 1983

By N M. Player, R P. Varden, E Jones

"An effective geotechnical design provides an accurate and appropriate assessment, balanced with a mining company’s risk profile. Justifying the cost of slope assessment requires an understanding of the input sensitivities, and resultant risk, to achieve a slope of a required functionality. As a project progresses from Scoping to Feasibility, the geotechnical risk becomes better resolved through increased expenditure on drilling, testing, analysis and modelling as long as the input data is appropriately spatially distributed. Providing accurate and appropriate geotechnical assessments in the early stages provides confidence in all following stages, especially where initial analysis indicates difficult geotechnical conditions. It is also in the early stages of project definition that there is most opportunity to maximise the value of the deposit through investigations into optimal mining methods.This paper examines the advantages of geotechnical engineering input through a project study period. Early geotechnical involvement allows the Scoping and Pre-Feasibility Studies to be more effective. Operational risks can then be better understood and dealt within the Feasibility Study phase, also ensuring that the correct risks and management controls are put in place.With commodity price pressure and cost of resource recovery in a downturned industry, reducing the risk to cash flow, resource recovery and safety should be a primary goal for all mining companies. Reduced risk can be effectively achieved through geotechnical design of slopes to achieve a required performance as part of an integrated study to the Reserve definition and mine design.Citation:Varden, R P, Player, J R, Player, N M and Jones, E, 2016. Justifying Slope Design Risks and Costs, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 185–201 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016