Search Documents

By D Ray, D Brett

A clay-capping trial was established in 1996 on Magazine Dump at the Mt Lyell Copper Mine. The trial was initially constructed under the Mount Lyell Remediation Research and Demonstration Program, a co-operative venture between the State and Federal governments. The detailed engineering design for the clay cover included the following features; reshaping and compaction of dump batters, 5 m vertical bench interval, overall side-slopes of 2.5:1, emplacement of clay in four 150 mm lifts, compaction by a 10 t vibrating roller or ætrack rollingÆ on batters with density testing for quality control. A small section at the base of the dump ( The trial also generated certain unexpected findings. Field permeability tests on the cover yielded uncertain results and oxygen remains available throughout the dump. The flow data indicate that, while total outflow has decreased as a result of storm shedding, inputs from groundwater and batter infiltration are still significant. Outflow during the driest weeks of the year may have risen following capping. Detailed assessment of the data is hampered by insufficient pre-capping information; however, there is a possibility that conductivity flux emitted when flows in the receiving environment are at their annual minimum is unchanged or worse post-capping.

Jan 1, 2003

By B Oostendorp, R van der Merwe, P

In order to assess whether polysaccharide depressants are strongly or weakly and reversibly bound to the surface of talc, a series of experiments was conducted on New York talc in which the floatability of the talc in a microflotation cell was determined. The talc was conditioned in solutions of carboxymethyl cellulose (CMC) or guar gum in 10-2 ionic strength Ca(NO3)2 or Mg(NO3)2. The talc was then washed with four successive aliquots of water, or cation solution, to try to remove the polymer and the flotation response of the talc was assessed. CMCs of different charge (DS) were used to assess the effect of charge on the strength of bonding. The results show that CMC and guar gum could be removed to a large extent from the talc surface by washing with water (the floatability was restored), however very little could be removed from the surface by washing with cation solution. The higher charge CMC was easier to remove from the talc planes in the absence of cations than the lower charge CMC. Thus CMC bonding to talc has been shown to be irreversible or very slowly reversible only if cations are present, implying that cations are necessary to keep the polymer bound to the surface of the planes to effect depression. The presence of ions in solution also had the effect of maintaining surface coverage of the talc by guar gum.

Jan 1, 2005

By D Matthews

Increases in mining and production capacities can have a major impact on the productivity of a mining and production facility during the construction and commissioning period. With minimised production loss in mind, a multi-phase modular plant design was implemented on the Khumani Mine in the Northern Cape, South Africa. The first phase involved a run-of-mine (ROM) crushing facility and the subsequent modular processing facility with capacity for 8.4 million tons per annum (Mt/a) product. An interim phase comprising modular additions to the processing facility increased capacity to 10 Mt/a product, with tie-ins occurring during maintenance periods. The second phase involves a second ROM crushing facility and modular additions to the processing facility, increasing capacity to 16 Mt/a product. This paper outlines the design considerations and limitations with modular design that need to be considered and shows how effectively construction and commissioning were implemented within shut-down and maintenance periods.

Jul 11, 2011

By S Pontual

Compact and field portable infrared spectrometers have been increasingly used over the past few years by an exploration industry constantly searching for a technological edge and the ability to more accurately and rapidly assess project areas. In particular, this technology allows large amounts of data to be rapidly collected on-site and sample mineralogy, mineral crystallinity and mineral composition to be quickly assessed. In recent years, short wave infrared (SWIR) reflectance spectroscopy has proved useful in a wide range of geological environments and at various stages of exploration programs, from grass roots reconnaissance through drilling programs and resource evaluation. Unfortunately these data have frequently been analysed and interpreted in isolation using time consuming data analysis techniques removed from the realities of a fast moving exploration industry. This paper presents new analysis techniques which allow these data to be efficiently integrated in the exploration program. Although SWIR data contain a wealth of mineral information it is impractical to use this information in its raw form. A more effective approach involves the extraction of key characteristics of these data (ie mineralogy, mineral composition and crystallinity) as numerical values, and the integration of this ædigital mineralogyÆ with more conventional exploration datasets (eg geochemistry, coordinate data, etc). This paper demonstrates that the integrated analysis of sound geological observations, geochemical, spatial and spectral data can quickly lead to a greater understanding of the nature and distribution of target mineralisation. As a first step, software driven pattern matching routines enable the identification of the major clay mineral species in a series of samples (eg kaolinite, montmorillonite and sericite). This allows the major alteration facies and their spatial distribution to be identified. Quantification of diagnostic absorption feature characteristics then allows more accurate determinations of mineralogy to be made (eg mineral composition and crystallinity). Examples of the application of SWIR analysis for alteration mapping from selected porphyry and epithermal systems from around the Pacific Rim are discussed. The data presented are derived from a variety of locations and sample types including drill core, ridge and spur rock chip samples, soil samples and geochemical pulps. In these large alteration systems, the spectral data can be used to describe and map the distribution of various alteration facies as many of these are characterised by clay and phyllosilicate mineral assemblages and are detected by SWIR analysis (eg smectite, chlorite, biotite, illite, muscovite, kaolinite, dickite, pyrophyllite, alunite, etc). In addition, the ability to evaluate even subtle trends in mineral crystallinity and composition is often vital in these systems when looking for vectors towards higher temperature parts of the system. In addition to detailed evaluation of mineralogy, the integration of digital mineralogy data with geochemical data leads to the ability to describe not only geochemically anomalous intersections or regions but also to recognise associations between subtle changes in mineralogy and target mineralisation. This is often important because understanding these mineralogical associations can lead to more accurate targeting and rapid assessment of the project.

Jan 1, 1999

By J Hadjigeorgiou

The stability of open stopes in underground hard rock mines is influenced by several factors including the shape and size of the excavation, surrounding stresses as well as the degree of jointing. This paper presents a design methodology for stope analysis in jointed rock masses. The proposed approach relies on geological structural data to construct realistic three-dimensional joint network models. The stability of an open stope is determined based on a limit equilibrium analysis.

Jan 1, 2000

The Gj0vik Olympic Mountain Hall is the world's largest underground cavern for public use and was created primarily to facilitate the ice hockey tournaments for the 1994 winter Olympics in Norway. The cavern has a span of 61 m, is 91 m long and is 25 m high. Ordinarily, rock caverns have a span width of 15 to 25 m, however, temporary mining caverns of up to 60 m have been excavated and natural caves with even greater dimensions occur. The Gj0vik Olympic Mountain Hall is unique as it is for public use with a capacity for 5800 spectators. Blasting was conducted with a high production rate at normal costs due to detailed planning and strict supervision of each round. The initiation system and vibration monitors were the main tools to control vibration levels and to facilitate a high production rate. It was of utmost importance that the rock remaining in the roofs and walls was of high quality after blasting to avoid rock fall, rock slides and excessive maintenance work.

Jan 1, 1995

By Hanley J

Coal winning in the Latrobe Valley exceeds 45 mtpa uses a small number of Bucket Wheel Excavators and high speed conveyor systems. While this equipment offers many advantages in the production cycle, incorrect use can lead to low productivity and risks to the safety of the operators and equipment. The mining equipment is of high capital value and easily damaged when used outside the correct operating range. In the extreme case, this can result in total machine collapse, having major implications for personnel safety as well as production and costs. With an active productivity improvement program in the Latrobe Valley in the last two years resulting in a 50 per cent reduction of personnel, many experienced operators have retired. Mine management are facing the urgent need to rapidly train new operators to maintain high productivity levels and reduce the risk of accidents to personnel and high capital cost plant. With the assistance of the Central Gippsland College of TAFE a Certificate Level course has been developed for open cut operators. The course covers all essential training needs for the Latrobe Valley mines. The training is developed from National Competency Standards, allowing transfer of skills, and is flexible to suit other enterprises. It has been written for self-paced learning with the total job understanding, and to have competency-based learning outcomes, training tasks and assessments built-in to modules. With the introduction of this new training program, management is convinced that the element of risk within the mine will be significantly reduced. For these reasons it is an ideal training model for other enterprises.

Jan 1, 1994

By J Robertson, D Williams, H D. Plewes

The co-mixing of tailings and waste rock involves the intimate blending of tailings and waste rock to create a new material (Co-Mix) with superior physical and hydraulic properties. The new material has a low hydraulic conductivity, low compressibility, high water retaining capacity and high shear strength. Co-mixed tailings and waste rock restrict oxygen entry and water seepage to minimise acid generation and metal leaching. When compacted, Co-Mix materials have low volume change characteristics with respect to total stress and matric suction together with high shear strength. Co-mixed tailings and waste rock may be used to construct cover systems, internal barriers and seals, confinement structures or a full depth waste repository. The theoretical properties of Co-Mix blends are investigated. The results of a laboratory program to characterise the physical and hydraulic properties of co-mixed tailings and waste rock are presented. Various ratios of tailings were blended with different waste rock materials. Hydraulic conductivity tests were conducted at confining pressures ranging between 0 and 400 kPa. The saturated hydraulic conductivity for the Co-Mix materials was found to vary between 4 + 10-5 m/s and 5 + 10-9 m/s depending on blend ratio, waste rock type and confining pressure. These results together with other physical properties show excellent hydraulic and strength characteristics can be achieved for Co-Mix materials.

Jan 1, 2003

By M S. Powell, M P. Bueno

The commonly used SAB, SABC and run-of-mine (ROM) ball mill circuits can achieve high throughputs with good operating stability. However, these circuits consume a substantial amount of grinding media, which can have a substantial impact on the OPEX and the æcarbon footprintÆ, specifically when viewed as an æembodiedÆ energy input. On the other hand, fully autogenous (AG) circuits can operate at much lower operating costs, but with limited throughput. The control of AG mills, fed by ores with hard and soft components, can also be challenging, due to the sensitivity of the mill to the ratio of hard to soft components.In this paper, a multi-component modelling approach was used to demonstrate that the harder component should be used as grinding media, and its use should be kept to a minimum to avoid reduction in the mill throughput. There is an optimal blend of hard to soft, and any optimal blending condition is both ore-dependent and mill-specific. Establishing this blend is challenging, and consequently discourages the use of autogenous mills. The new modelling approach addresses this challenge by providing a quantitative prediction of the influence of blending soft and hard components in a mill. This prediction can then be used to establish the required blend for maintaining a stable and efficient operation in autogenous grinding mode.CITATION:Bueno, M P and Powell, M S, 2012. How to use hard ore components as grinding media, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 31-36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

Dr. Willett. I will start by answering one or two general points which have been posed. The first point is a question of liability of a seam to spontaneous combustion. Some seams are very liable to spontaneous combustion. Some seams are not liable at all except in most abnormal circumstances, and some seams have a liability somewhere between these two extremes. Dr. J. S. Haldane made the comment some 50 years or so ago that if you try hard enough you can make any coal seam in the world fire spontaneously. Many heatings have in fact occurred because the coal has been allowed to be ground up into a fine state and there has been air leakage through it for many years. This has resulted in spontaneous combustion which would not have occurred in some seams unless conditions had been very abnormal indeed. One comment I heard while listening to the discussions of one team was the importance of encouraging morale and the team seemed to go to the extent of suggesting that this was more important than the actual technical action taken. Though I agree that everything possible should be done to encourage morale, it must be in conjunction with the correct technical method of dealing with the Emergency.

Jan 1, 1973

By Aziz N. I

Examination of the geology and support performance at two site leads to development of an under tanding of the influence of caving on powered support rating. The two site represent the current extremes in support rating, i.e. 6/260 tonne supports operating in the Hirst seam at Solsgirth Colliery, Scotland, and 4/900 tonne supports operating in the Bulli seam, West Cliff Colliery, Australia.A conceptual model considers the coal ahead of the face, the powered support, and the caved waste to be three yielding foundations which interact to control the subsidence of the roof strata.The caving mechanisms identified for the strata of the Hirst and Bulli seams, are different. These mechanisms being related to rock properties - the palaegeography and depositional conditions at each site-produce caved wastes with different yield characteristics.An analysis of the results obtained for convergence and support reaction during production cycles at both sites shows the manner in which support reaction is developed, indicating the importance of higher setting load densities in the Bulli seam.Evaluation of the work done on the subsiding roof strata during typical production cycles by two of the yielding foundations the powered support and the caved waste immediately behind the powered support - further demonstrates the influence of caving mechanisms on support rating.

Jan 1, 1989

By Weller KR

Completely dry or completely wet materials are comparatively easy to screen, but materials with moisture contents between these two extremes can present varying degrees of difficulty. The presence of moisture can impair the performance of a dry screening plant in a number of ways: ò agglomeration of fine undersize particles onto larger oversize particles, resulting in the fine particles being misplaced to the oversize; ò increasing attractive forces between particles that hinder stratification and particle presentation to the screen; and ò blinding of the screen apertures caused by fine moist particles clinging to the screen which reduces the effective aperture size and the open area of the screen. Test work on full-scale screens has shown that the agglomeration of fine particles onto larger particles only occurs once the equilibrium moisture content of the ore is exceeded, and that the quantity of adhering fines present is proportional to the surface area of the larger particles. An -adhering fines screen model has been developed from this work, and by using relationships derived between the model parameters and feed moisture content, the effect of changes in feed moisture on both product quality and operation of iron ore dry screening plants is predicted.

Jan 1, 1993

Continuous improvement in environmental management assists in the achievement of sustainability goals for the processing of minerals. The use of regular internal environmental audits (scored or unscored) which form an integral component of an Environmental Management System (EMS), provide demonstrable evidence of this improvement. Case studies are presented for a number of major coal mines in the Hunter Valley, where regular internal environmental audits have been undertaken every two to three months, over periods varying from 18 months to five years. Examples of the benefits of improved environmental performance (driven by the audit process) to sustainable development are provided.The auditing process as described here for coal mines, and coal handling and preparation plants, is equally applicable to the processing of other mineral ores, metalliferous mines, quarries, and oil and gas projects.

Jan 1, 2004

Analysis of the topography associated with large vertical strains measured in the upper crust in the Basin and Range and elsewhere in the US Cordillera shows that it varies systematically with upper crustal strain such that it decreases where tectonism has resulted in relative thinning. The magnitude of topographic deflection suggests that the amount of thickening or thinning of the upper crust cannot also be reflected in vertical motions of the Moho discontinuity, nor can the vertical strain be isostatically accommodated by inflow or outflow of asthenosphere, mantle lithosphere or mafic lower crust. Simple isostatic calculations show that the compensating medium had a density probably within 100-200 kg/m of average upper continental crust, thus indicating that the compensating medium lies within the crust and is probably in large part quartzose. This conclusion is in accord with laboratory experiments on the strengths of rocks, and with reflection seismograms in deformed regions which suggest that the Moho is generally flat beneath regions of extreme gradients in upper crustal vertical strain. The upper crust floats on a quartzose layer in the mid-crust which, under orogenic conditions, is apparently so weak that it behaves as a relatively inviscid fluid at geologic timescales (> 10,000 a) and subcontinental lengthscales (100-1000 km).

Jan 1, 1990

By M-E Boucher

While the haematite concentrates produced in Eastern Canada and the magnetite concentrates that Australia will soon be producing are different feed materials, the pellets they produce have similar physical and metallurgical properties. This paper will examine the similarities and differences in the evolution of pellet microstructure for pellets produced from magnetite and haematite. The molten slag phase generated at high temperatures has a lower melting point when in contact with magnetite compared with haematite due to the higher divalent iron content. The presence of some slag is beneficial for bonding but too much can inhibit oxidation of magnetite, although slag generation at lower temperatures reduces energy usage. In pellets produced from haematite, magnetite is generated artificially from the combustion of the carbon particles added to the pellet feed as a source of energy. Maintaining the optimum production level and mineralogy of such æsecondaryÆ magnetite, allowing for its subsequent reoxidation, is important for the quality of haematite pellets. In both magnetite and haematite pellets, balancing the slag formation and oxidation (re-oxidation for haematite pellets) of the magnetite (secondary magnetite for haematite pellets) is necessary.

Jan 1, 2007

By Mitchell I, Gelfi P, Dunne R, Pyper R

Dump leaching at Teller in its present form began in the fourth quarter of 1988 as an adjunct to milling operations. Initial plans called for a dedicated dump leach facility capable of processing ore at an annual rate of 2.0 million tonnes. Construction of a dump leach pad, collection and process ponds, carbon adsorption system, elution plant as well as reagent addition and ancillary facilities was initiated in mid-1988. During the course of construction, additional reserves were proven. As a result, design throughput was increased to 4.0 Mtpa. Leach pad capacity and solution supply systems were upgraded to handle the larger throughput. However, the carbon adsorption/elution facilities were not upgraded due to space limitations. During 1990 it was decided to expand the dump leach operation to 6.0 Mtpa. Construction of a second leach pad was required which was initiated in early-1991. Plans were again upgraded prior to completion to a target annual throughput of 10.0 million tonnes was. A further two leach pads have been constructed. The first of these being completed during the latter part of 1992. Construction of the latest and largest pad commenced early in 1994.

Jan 1, 1994

By S R. Grano

The selection of the proper frother, specifically for a given ore, is essential in flotation. Traditionally, strong and stable froths are required in the scavengers, where metal recovery needs to be maximised, while selectivity must be achieved in the roughers and cleaners, where grade of concentrates is the main issue. The physical properties of a froth are determined both by frother type, by process water composition and by the amount and nature of the suspended particles. The evaluation of different frothers, in terms of metallurgical performance, is complicated at plant scale, since it may lead to periods of malfunctioning of the process and unacceptable decreases in recovery. On the other hand, evaluation based on frother chemistry only, is often unsatisfactory, because the frothing response is strongly ore dependent. A procedure, and proper tools, was developed at the Wark in order to perform the screening of candidate frothers at batch scale on real pulp samples. The main parameters related to froth stability (half-life time, froth height) are measured after introducing the pulp samples into a foaming column, where different conditions in terms of frother addition, agitation and aeration can be maintained. The approach has been applied to the selection of frothers for the flotation of an Australian sulfide ore. Procedure and results are discussed.

Jan 1, 2006

By K Nakashima, K Aya, T Sumita, N Saito

Electro slag remelting (ESR) is one of the methods used to produce high-cleanliness steel. In the ESR method, the product steel electrode is immersed in flux, and the electrode is melted by the Joule heat of the flux generated by high current. CaF2-based melts are mainly used as fluxes, but the electrical conductivity of CaF2-based melts varies widely among researchers and measurement methods. Therefore, this experiment aims to measure the electrical conductivity of CaF2-based melts based on the van der Pauw-Ohta method, which does not require the cell constant that is a fundamental error factor in electrical conductivity measurement at high temperatures. The measurement temperature was set at 1450–1600°C, and dehydrated Ar flowed through the furnace at 200 mL/min. Electrodes were fabricated by Pt-30mass per cent Rh alloy, and the electrodes were connected to an impedance analyser using a four-terminal probe. The electrodes were immersed in the melt, and the impedance and phase angle were measured by AC frequency sweep (50 Hz to 200 kHz). The electrical conductivity was then calculated by utilising the impedance’s real part values when the impedance’s imaginary component was zero. The electrical conductivity showed a positive temperature dependence. The electrical conductivity of 60(CaO⋅Al2O3)-40CaF2 melt increased with increasing temperature but was found to be roughly one-third of those of the previous studies. In the conductivity measurement of 60(CaO⋅Al2O3)-40CaF2 melt, the AC frequency with a phase angle of 0° was found to be different depending on the temperature and immersion depth. By sweeping the frequency, the impedance at the phase angle of 0° can be obtained, which enables us to measure the electrical conductivity more accurately.

Jun 19, 2024

By Neville Rockhouse

This paper examines the interrelationship of conducting full risk assessments in the context of the coal mining industry and under the framework of the Health's Safety in Employment Act 1992. In the context of Occupational Health's Safety, Risk Management is a holistic management process that can be used by individuals working in all organisations and from all industries. The Australian New Zealand Standard 4360: 2004 defines a Risk as being; The chance of something happening that will have an impact on objectives. This definition is followed by several notes that include: a risk is often specified in terms of an event or circumstance and the consequences that may flow from it, risk is measured in terms of a combination of the consequences of an event and their likelihood, and risk may have a positive or negative impact. For the purposes of this paper, the above definition will be adopted. This paper examines the newly expanded approach of the fully documented risk management process in the New Zealand coal mining industry. This is done in the context of the coal mining regulations but more importantly by using the framework of the Health & Safety in Employment Act 1992. This legislation under Section 6 requires all employers to, Take all Practicable Steps to prevent harm coming to employees while at work and to others who might be at or in the vicinity of a workplace. When the term 'all practicable steps' is studied, one can clearly see that such steps should be the same steps taken that a prudent and reasonable person would have taken given the same type of circumstance. Due to the fact that in New Zealand parliament made statutes is administered by a Government Department, means that their breaches will be heard before a judge in the District Court. Under the Westminster System of Justice, a basic dictum of that court in matters relating the occupational health and safety is that a breach needs to be satisfied to a specific standard. That standard is, 'Beyond a reasonable Doubt'. One of the primary benefits of adopting a proactive approach to risk management is that if the industry were to adopt similar approaches, then this mythology could be seen as an industry standard. As such, the approach carries the same status in a court of law, as that of an Approved Code of Practice.

Jan 1, 2007

A novel approach to validate size distributions obtained from bubble sizing techniques is introduced. The experimental rationale consists in verifying whether the output features the anticipated bi-modality when two uni-modal populations (ca. 0.5 and 5 mm) are mixed in a bubble column. The degree of deviation is quantified by comparing the calculated and real proportions on a volumetric basis. A sampling-followed-by-imaging technique was used to proof the concept. The results showed the anticipated bi-modality in which the real and calculated proportions corresponded with a deviation of less than 15 per cent, considered good given the severity of the test. However, the deviation was correlated to the superficial gas velocity (Jg) in the column and was consistently against smaller bubbles. Possible sources of bias are suggested.

Jan 1, 2005