Search Documents

By Arnt Solbu, Jomar Thonstad

The reaction between CO, and aluminum in cryolite-alumina melts in contact with aluminum has been studied by passing CO2 over the melt. In unstirred melts a homogeneous reaction between dissolved metal and dissolved CO2 was observed. In stirred melts in which convection was induced by bubbling argon through the melt, the dissolved metal apparently reacted mainly with gaseous CO2. The rate of formation of CO increased slightly with increasing depth of the melt, and it did not depend on whether CO2 was passed over or bubbled through the melt. The rate of formation of CO increased with increasing area of the metal/melt interface and with the application of anodic current to the metal. It is concluded that the dissolution of metal into the melt is the rate-determining reaction. THE current efficiency in aluminum electrolysis is determined by the rate of the recombination reaction between the anode gas and the metal: 2A1 + 3CO2—A12O3 + 3CO [1] as originally stated by Pearson and waddington.1 The occurrence of this reaction in cryolite-alumina melts in contact with aluminum was first verified experimentally by Schadinger.2 Thonstad3 has shown that the reaction may proceed further to give free carbon: 2A1 + 3CO— A12O3 + 3C [2] Normally only a few percent of the CO formed undergoes such reduction. The mechanism of these reactions has not yet been clarified. Aluminum, as well as CO,, is soluble in the melt. The solubility of aluminum in cryolite-alumina melts at around 1000°C corresponds to 75 x 10- 6 mole A1 per cu cm,4 while that of CO2 is only 3 x 10-6 mole CO, per cu cm.5 Taking into account the stoichiometry of Reaction [I], the ratio between dissolved aluminum and dissolved CO2 available for the reaction in a saturated melt is about 40. Therefore, as will be shown in the following, the reaction probably mainly occurs between gaseous COa and dissolved aluminum. The dissolved aluminum presumably consists of subvalent ions of aluminum and sodium.4'6 Since the interpretation of the present results is not dependent upon the nature of this solution, the dissolved metal will be designated solely as Al+ in the following. The reaction can then be divided into four steps: A) dissolution of metal, e.g., 2A1 + Al3 — 3A1+ [3] B) diffusion of dissolved metal through a boundary layer; C) transport of dissolved metal through the bulk of the melt; D) Reaction [1]. If dissolved CO, takes part in the reaction, three additional steps embodying the dissolution and transport of CO2 must be added. schadinger2 observed, when bubbling CO2 through the melt, that the rate of formation of CO (in the following designated rfco) did not depend on the distance from the metal surface. The results also indicate that the rate of bubbling did not affect the rfco. When passing CO, over the melt, Revazyan7 found that the loss of metal did not depend on the depth of the melt above the metal or on the flow rate of CO2, and concluded that Step A is rate-determining. In an unstirred melt, however, Gjerstad and welch8 found that the rfCo decreased with increasing depth of the melt, indicating that step C was rate-determining. It thus appears that the rate control of the process depends on the experimental conditions, particularly on the convection. In the present measurements the reaction has been studied in unstirred as well as in stirred melts. EXPERIMENTAL AND RESULTS The experiments were carried out at 1000°C in a Kanthal furnace with a 10-cm uniform temperature zone (±0.l°C). The melts were made up of "super purity" aluminum (99.998 pct), hand-picked natural cryolite, and reagent-grade alumina. In experiments where alumina crucibles were used, the alumina content in the melt was close to saturation (13.5 wt pct9); otherwise it was 4 wt pct. Pure Co2 (99.85 pct) was passed over the melt, and the exit gas was analyzed for CO2 and CO by the conventional absorption method.3 From the weighed amount of CO (as CO2) the rfco was calculated as the number of moles of CO formed per min per sq cm of the surface area of the melt. The amount of carbon formed by Reaction [2] was not determined. As already indicated the rfco is much higher than the rfC, by Reaction [2]. Since the rfC probably is proportional to the rfco, the measured rfco should then the proportional to, but slightly lower than, the total rate of Reactions [I] and 121. In general the scatter of results obtained in duplicate measurements was ±5 to 10 pct, while within a given run a precision of ±3 to 5 pct was obtained. The various crucible assemblies that were used will be described below. Measurements in Unstirred Melts. When carrying out aluminum electrolysis in small alumina crucibles. Tuset10 observed that after solidification the lower part of the electrolyte was gray and contained free metal, while the upper part near the anode was white and contained no metal. One may test for the presence of free metal by treating with dilute hydrochlorid acid.

Jan 1, 1969

BENEFICIATION AND CONCEN'TRATION; FROTH FLOTATION U.S. 4,069,144 - In the froth flotation beneficiation of phosphate rock using at least an acid flotation step and an amine flotation step, the crude ore is dried either during transport or storage or by air circulation immediately prior to classification, and the dried ore mixed with water and classified prior to flotation The preliminary drying substantially eliminates the usual problems with clay slimes G. C. Johnson and A. E. Schweizer, assigned to Mobil Oil Corp. Jan 17. 1978. 4 pp (209- 11) . Filed 1 1-19-75 (633,535).

Jan 1, 1979

By Arthur Baker

The orebodies are long bedding-plane lenses of chalcopyrite and sphalerite, associated with garnetite masses. Most of the orebodies are within a 50-ft thickness of Cambrian limestone; other Paleozoic limestones and dolomites are locally metamorphosed but only slightly mineralized. Pre-mineral faults are numerous, but shallow folds were the main ore-localizing structures.

Jan 12, 1953

By C. C. Harris

This article presents a general equation describing the xYt surface in batch grinding. This equation contains as special cases most of the relationships which have been deduced from kinetic studies. In an earlier paper an analytical solution of the integro-differential equation of batch grinding was proposed1 as a first approximation of the xYt surface.' A more general equation will be presented here, which appears to combine in a single statement many conclusions reached by experiment. A possible underlying mechanism is that the changing product fineness leads to changes in the particle crushing strength and in the probability of encounter with the crushing media.

Jan 1, 1969

By Dan White

Stress measurements taken at Climax, El Teniente, Henderson, Lakeshore and Urad mines indicate that the deposits cited are generally subject to an inclined stress field that can be highly anisotropic. The horizontal stresses vary significantly between deposits and exceed the measured vertical stresses at Henderson and El Teniente mines. Experience at Henderson, Lakeshore and Urad mines is used to suggest a relationship between cavability and the premining stress. In poorly fractured, high strength rock masses, high stresses can assist the caving process. In well fractured, low strength rock masses, caving is ensured by breakage along fracture planes. The relationship between ground weight and the premining stress is also investigated. Ground weight problems appear to be most related to the competence of the ground rather than the magnitude of the premining stress as supported by experience at Climax and El Teniente mines. Recent developments in block caving favor the extraction of poorly fractured, high stressed rock. Accompanying the development of these deposits are new problems such as rock bursts. These pose particular problems to mine designers in that no experience currently exists in combatting rock burst problems at block caving mines.

Jan 1, 1984

By W. J. Keep

Cast-iron, or pig-iron, is iron which contains all the carbon that it could absorb during its reduction in the blast-furnace. As is well-known to chemists, carbon exists in cast-iron in two distinct forms. In chemical union, as "combined" carbon, it cannot be discerned, except as it may increase the whiteness of the fracture, in so-called white iron, or carburetted iron (sp. gr. about 7.72). Carbon mechanically mixed with the iron as graphite is visible, varying in color from gray to black, while the fracture of the iron, according to the color and amount of graphite it contains, ranges from a light to a very dark gray. The specific gravity of graphitic iron is about 7.40. Silicon in cast-iron is evidently to some extent combined with the iron and the carbon ; but whether it exists also in a form corresponding with graphitic carbon, mechanically mixed with the remaining mass, is a question still in dispute, which we have not in this paper endeavored to answer. It has been the opinion of many writers on metallurgy, and many foundry men, that silicon is in every way injurious to cast-iron. Yet

Jan 1, 1889

By George Rice

THE subject of violent bumps in coal mines has been again brought to attention by a recent succession of such occurrences in the coal mines of the Cumberland field of eastern Kentucky and southern Virginia, which have caused fatalities and injuries to underground employees, a report on which is being issued by the United States Bureau of Mines1. The A.I.M.E. has had two valuable papers on bumps in the No. 2 Mine, Springhill, Nova Scotia, each followed by general discussion on bumps and their causes2. This paper gives a brief review of suggested causes and remedial measures given in English, Canadian and United States reports on bumps in coal mines, and then presents suggestions arising from the writer's recent investigation of the bumps in the Cumberland mines, made at the request of the mine operators, to determine the causes and remedies. These bumps, which occur under the simplest natural conditions, provide better opportunity for analysis of causes and effects than afforded under more complex conditions. The simple conditions in this field consist of relatively thin and level coal beds and uniform roof strata free' from folding and faulting.

Jan 1, 1935

By Leo Horvitz

PETROLEUM and natural gas are composed principally of the saturated hydrocarbons ranging from methane, the lightest, to nonvolatile liquids and solids containing approximately thirty-five carbon atoms. A technique for locating buried accumulations of these hydrocarbons before drilling obviously requires that some of the hydrocarbons leave the deposit and migrate toward the surface of the earth where they may be detected in their original form. Earliest attempts to link near surface hydrocarbons to petroleum at depth were apparently made by Laubmeyer1 in Germany and by Sokolov2 in Russia. These investigators collected samples of soil air from boreholes one to two meters deep and analyzed them for traces of hydrocarbons. They found that soil air over producing areas is richer in these constituents than is soil air over barren areas.

Jan 12, 1954

By Carl R. Christiansen

Since the first pay hole in Missouri's "New Lead Belt" was drilled in 1955, this district has become one of the world's leading sources of lead. The belt extends from north of Viburnum in a southerly direction to near Eminence, a distance of about 35 miles. The St. Joseph Lead Company was the discoverer and first to develop new mines in the Viburnum area. Since the discovery of the New Lead Belt, many companies have engaged in exploration programs and several major companies have become active in development of new mines. These include Cominco American, Inc., which operates a joint venture with Dresser Industries; Ozark Lead Company, a subsidiary of Kennecott Copper Company; and Missouri Lead Operating Company, a joint venture of Arnax and Homestake. St. Joseph Lead Company, with over 100 years of experience in the Old Lead Belt, has served as a leader in development of equipment and mining techniques, making its properties some of the most efficient mining operations in the world. The new producers give the district the benefit of fresh viewpoints, as their engineers are mostly from outside of Missouri and their previous experience has been considerably different from conventional lead belt practices. While all operations are similar in that they are room-and-pillar, the diverse experience of the operators has produced a group of mines that employ a variety of equipment and mining techniques to give increased efficiency

Jan 1, 1970

By H. Foster Bain

Jan 1, 1910

By J. J. Thomas

THIS investigation was undertaken to determine, if possible, the relation between static and dynamic tensile tests as measured by the work required to break test specimens slowly, in a tensile testing machine, and rapidly, by means of a falling weight. It was hoped that the investigation would throw some light on the role played by ductility under different rates of application of load. FIG. 1.-STRESS-STRAIN DIAGRAM. In problems of design, it is usually assumed that the moduli of elasticity of all steels are equal; viz., about 30,000,000. The stress-strain diagram within the elastic limit is a straight line, as shown in Fig. 1, where OA is the curve of a hard steel and OB that of a soft steel. If the modulus of elasticity is constant, as assumed, the slope of the line OC

Jan 2, 1921

Jan 1, 1955

By James E. Lawver, James L. Wright

This paper discusses the design and calibration of a Faraday pail for measuring electric charge. The paper also shows that at least for two minerals, quartz and calcite, the phenomenon that Johnson termed "reversibility" can be explained in terms of the contact electrification between the minerals and the metal rotor of an electrostatic machine. Each year the free world produces about 13 million tons of mineral concentrates by electrical separation. However, despite the rather general acceptance of electrical concentration as an industrial process, research in this area has lagged far behind the efforts devoted to competitive processes such as froth flotation. The purpose of this paper is to describe the design and calibration of a Faraday ice pail for measuring charge density on mineral grains and to show some of its applications in the area of electrostatic and electrodynamic research. THE DESIGN AND CALIBRATION OF FARADAY PAILS FOR ABSOLUTE CHARGE MEASUREMENT The electric charge on mineral grains at a given time during an electrical concentration process is de- pendent on many factors and cannot, in general, be accurately calculated a priori. It is thus important to devise a method of measuring absolute charge. One method of measuring electric charge is to note the potential rise of an electrometer when charged particles drop into a Faraday pail. Two types of Faraday pail have been constructed and calibrated. The first type, Faraday Pail I (Fig. 1), is a vertical pail originally designed to measure the charge due to contact electrification between mineral grains and a metal rotor or due to conductive induction when mineral grains are passed over a rotating cylinder in the presence of an electric field. The second type, labeled Faraday Pail II (Fig. 2), is a horizontal pail designed to determine the charge distribution of mineral grains after they pass through the separating zone of the electrical concentrator shown in Fig. 4. The main advantage of the horizontal pail is its low head-room requirement and the long opening which enables the experimenter to sample the entire width of the stream of minerals being separated. The Faraday pails were calibrated in the following manner: A calibration head was constructed in the form of a hollow brass sphere that could be held in an insulated metal cylinder by vacuum (Fig. 1). The capacitance of the sphere was calculated by measuring the capacitance of the sphere and cylinder combined and that of the cylinder alone and subtracting the latter measurement from the former. The sphere was then charged to a known potential (V) and allowed to drop into the Faraday pail which was attached to a Keithley Model 610A electrometer. This instrument has an accuracy of 2% full scale and has

Jan 1, 1969

By Edmond S. Miksch

The morphology and growth rate of ice grown in supercooled water are markedly affected by convection of the water. A dendritic ice sheet with water flowing past the dendrite tip exhibits deflection of the dendrite spine toward the upstream direction, accelerated growth of secondary spines on the upstream side, and suppression 01" secondaries on the downstream side. Flow causes a thin disk to become corrugated, the corrugations being parallel to the flow. Flow causes an increase in the growth rate of the ice. IF a small seed of ice is placed in slightly supercooled water, it grows initially as a disk with the axis of the disk parallel to the c axis of the ice crystal.' It appears that growth in the c direction is inhibited, while growth occurs with equal facility in all directions in the basal plane. It appears that growth rate as a function of interface temperature is very nearly equal for all directions similarly oriented relative to the c axis. Subsequent to the discoid growth, branching occurs and dendrites develop. The primary dendrite spines grow parallel to the six equivalent a axes of the crystal. Secondary, and in some cases, tertiary spines also grow in these directions. The highly anisotropic: dendritic growth indicates that there must be some finite difference of growth rate for different directions in the basal plane. These differences must be quite small, however, since if they were large, the discoid mode would not occur. Hence, it was expected that the dendrite growth direction could be deflected from the crystallographic direction by perturbation of the thermal field at the dendrite tip. Experiments were done in which perturbation of the thermal field was accomplished by causing the supercooled water to flow past the dendrite tip. The flow direction was perpendicular to the c axis of the crystal, and was perpendicular to the primary spine of the unperturbed crystal. Supercooled water was supplied by a 15 cm cubical copper box, which was refrigerated and insulated so it could cool water to temperatures down to —2oC, and maintain the temperature constant to O.l°C for the duration of a run. A lucite channel of rectangular cross-section, 12 by 24 mm, was mounted horizontally in the box, with one end open so water could flow into it, and the other end leading out through the wall of the box to a length of tubing leading: to an orifice plate 123 cm below. cnunMn s MIKSCH, MemberAiMe, formerly Research Associate, Research Associate, Fig. l(b)—Vertical section of apparatus A horizontal cross-section is shown in Fig. l(a), and a vertical section is shown in Fig. l(b). Means for observing the ice are shown in Fig. l(a). Collimated light passes through the ice sheet and forms an image on the ground glass screen. A lucite box containing dry air was employed to prevent condensation. Ice of the desired orientation was provided by the seed holder shown in Fig. l(b). This device was made of lucite, and had a reservoir in which ice could be frozen by placing it in a freezer. This reservoir com-unicated with the outside only through a narrow gap between two sheets of lucite. The seed holder (after ice had been washed off its exterior) was immersed in the tank of supercooled water, the narrow gap terminating in a slot in the top of the flow channel. Ice growing through a thin water layer in the gap between the two sheets of lucite was oriented so its c axis was perpendicular to the sheets. This orientation is an application of a growth phenomenon2 which causes ice growing along a smooth solid surface in supercooled water to orient itself so its c axis is normal to the surface. After the ice grew into the channel, further orientation was necessary, since the direction of the a axis

Jan 1, 1970

By W. C. Leslie

W. C. Leslie (Edgar C. Bain Laboratory for Funda mental Research)—This investigation, with its com bination of high-purity metal, calorimetry, and metallography, will serve as a model for annealing studies for a long time to come. The evidence for a competition between recovery and recrystalliza-tion is particularly convincing. The demonstration of edge-nucleated recrystallization was so clear that it may obscure the necessity for other types of "nucleation" sites; otherwise, single crystals of aluminum could not be recrystallized after cold work. At least three types of sites have been found to operate in iron: 1) high-angle boundaries, probably in the same manner as in aluminum, 2) matrix sites, 3) inclusions or second-phase particles. In each instance, the cells developed during cold work and perfected during recovery are the "nucle for recrystallization. Observations by ourselves and others of the dislocation structure of cold-worked metals and of the structural changes that occur during annealing have led us to doubt the validity of the basic assumption of the Lucke-Detert theory, and of the modification developed by Gordon and Vandermeer, that during recrystallization of a metal containing foreign elements in solid solution a high-angle boundary is ad vancing into a cold-worked matrix having a random distribution of solute atoms. We contend that an es sential part of the cold-working and annealing of solid solution alloys is the trapping of solute atoms by the low-energy "wells" afforded by individual dislocations and by dislocation arrays. If cells are formed during cold work, the cell walls are stabilized by this concentration of solute atoms. Thus, solutes inhibit recrystallization not only by decreas-ing the rate of high-angle boundary migration, but also by preventing the formation of high-angle boundaries by subgrain growth or coalescence, i.e., solutes can inhibit both "nucleation" and growth. In addition to stabilizing the dislocation Structure, the solute-dislocation interactions may produce clusters of solute atoms which are not as readily assimilated into the recrystallized grains as are individual solute atoms. There is an additional complication. The dislocation structure formed upon cold working a dilute solid solution may not be the same as that formed during cold working of the pure solvent metal. The solute can either enhance or minimize the formation of cells during cold working. Both effects have been observed in binary alloys of iron. The annealing process is inextricably connected with the mechanisms of strain hardening and solid solution hardening. Although the correlation between experimental boundary migration rates and the predictions made from the theoretical equations are impressive, it should be mentioned that in at least four other instances (Pb-Ag and pb-Au,15, Fe-Mn,16, Fe-Mo)17 the agreement was rather poor. In brief, while it is probable that the migration of high-angle boundaries is held back by solutes in the manner described, this is only a partial explanation of the total effect of solutes upon recrystallization of cold-worked alloys. Paul Gordon and R. A. Vandermeer (author's reply)— The authors first wish to thank Dr. Leslie for his compliments of this work. It is perhaps worth pointing out that some of Dr. Leslie's remarks are directed toward subject matter covered in two earlier papers in our work.18,19 We agree with Dr. Leslie's main contention that the exact nature of the metal structure in the vicinity of a boundary should have an effect on the boundary migration. The theory of Lucke and Detert does not take such detail into account, nor does it account for orientation effects on the migration rates. We assume that since our data checks the theory so well, the effects of detailed structure are statistically averaged out by the polycrystalline techniques used just as are the effects of orientation factors.

Jan 1, 1963

By Cyril Stanley Smith

Jan 1, 1949

By Cyril Stanley Smith

Jan 1, 1949

[FUQUA, H. B. and Thompson, B. E.: Oil and Gas Development and Production in North Texas for 1933, 107, 320; for 1934, 114, 417 Oil and Gas Development in West Texas 114, 438 FURMAN, W. F.: Heat and Corrosion-resisting Alloys. Printed in Oil & Gas Jnl., June 13, 1935 Furnace-bottom sand, uniformity, 73, 390 Furnace control, Isley apparatus, M27, 502 Furnaces (See also Holt-Dern; Blast Furnaces; Roasters; Wirebar, etc.): annealing: electric, 89, 424 gas-fired, 89, 425 gas vs. wood for nonferrous metals, 89, 422]

Jan 1, 1936

By Harold Margolin

The Ti-Al system certainly merits the investigative attention it has been receiving and this latest contribution by Blackburn is therefore to be welcomed. The titanium-rich end of the phase diagram shown here, as well as the diagram by crossley,17 Clark et a1.,18 and Tsujimoto and Adachi,29 reveal no other intermediate phase than Ti3A1, although a previous work by Ence and Margolin20 had reported an additional intermediate phase. Since then, Buerger Precession pictures of single crystals of 10.5, 11.5, and 12.5 wt pct A1 were made at New York university21 and the extinctions were found to be typical of a D6h a Ti structure. Some superlat-tice spots and/or streaks suggesting the presence of an Mg3Cd structure, i.e., Ti3Al, were also found. Since these specimens had been quenched from the y region20 and had revealed a Ti, it was concludedz1 that y does not exist and the structures interpreted as m + y could not be so considered. The absence of normal two-phase behavior in these structures had been indicated in the paper. Accordingly, the two-phase region y + 6 becomes a + Ti3Al and there is some agreement between the results of Blackburn and of Ence and Margolin20 as to both shape and existence above 900°C of an a + Ti3Al field. Crossley 17 proposed that Ti3Al is a line compound which decomposes congruently at 900°C. It is difficult to discount entirely the fact that clear two-phase structures, varying in amount with position in the two-phase field, could be detected above 900°C by Ence and Margolin.20 Precipitation during quenching could not have been so regular and the twin-phase syndrome17 does not apply. The heat treatment and quenching technique was essentially the same as was used by Crossley, whereas Blackburn, who used a rapid quenching procedure, also showed a two-phase a + Ti3A1 field above 900°C. If the two-phase field exists above 900° C, it is easy to picture a two-phase field which could account for the data of Crossley below 900°C without invoking a line compound existence of Ti3A1. All that would be necessary would be an 0 + Ti3Al/Ti3Al boundary which curved sharply to higher aluminum contents below 900° C. It is clear that the controversy must be solved by techniques which obtain data at elevated temperatures without quenching. It is conceivable that the difference in width of the a + Ti3N fields reported by Blackburn and by Ence and Margolin is due to the longer annealing times used by the latter investigators. The criterion for establishment of equilibrium in our work20 was the

Jan 1, 1969

By T. L. Fritzlen

Extrusion of aluminum alloys in this country is performed mainly by direct extrusion, therefore this paper is confined only to factors affecting the rate of extrusion by this method. Many factors affect the rate of extrusion of aluminum alloys. It is the purpose of this paper to present a discussion on the factors that are subject to technical control. Most of them are closely related, so that a clear-cut distinction between them is rather difficult. However, an attempt will be made to evaluate the effect of each factor separately, as far as possible. The most important factors only will be considered, and these will be discussed in detail under three general headings: (I) characteristics of the equipment, (2) size and structure of the ingot, and (3) temperature of ingot, cylinder, and other parts. It is a well established fact1 that the pressure and the speed of extrusion are related and are exponential functions of one another. Therefore, whenever a certain condition tends, for instance, to increase the pressure required for extrusion, it will reduce the extrusion speed if the pressure is maintained constant. For this reason, in this paper the effect of various conditions is expressed either in regard to their effect on the pressure required or the extrusion speed. Another established fact is the relation- ship between the temperature of the material being extruded and the pressure required to extrude. According to Schi-shokin,= this relationship is of the exponential type, and as the temperature is increased the pressure required is decreased. It would seem from the preceding that the greatest rates of extrusion can be obtained by the use of higher temperatures. However, as is well known, other factors intervene to limit the rate of extrusion of aluminum alloys when increasing the temperature. These factors will be discussed in detail later. Characteristics of the Equipment The capacity of the press determines * the maximum unitary pressure that can be applied for any given cylinder diameter. Pressures used for extrusion of aluminum alloys range from approximately 50,000 lb. per sq. in. to 150,000 lb. per sq. in., dependent upon the alloy and the size of the shape extruded. Higher pressures could be used to advantage, but existing steels limit pressures employed in the production of extrusions. Numerous mechanical characteristics of the extrusion press affect extrusion rate. The most important characteristics of the press itself are: (I) sensitivity of the main pressure valve and accuracy of pressure gauges, (2) accuracy of equipment to heat the cylinder uniformly and to control cylinder temperature, and (3) accuracy of means of measuring the speed of extrusion. The variables subject to control during the extrusion operation are pressure, temperature, and speed, and it is evident that the preceding characteristics

Jan 1, 1946