Search Documents

By HAROLD VINTON COES

MANAGEMENT has been tersely defined as getting things done through the efforts of other people; but before we proceed further, let us distinguish between administration, management, and organization. Oliver Sheldon in his book, "The Philosophy of Management," offers the following definitions: Administration is the function in industry concerned in the determination of the corporate policy, the co-ordination of finance, production, and distribution, the settlement of the compass of the organization, and the ultimate control of the executive.

Jan 1, 1943

THE Leadville tunnel, a Bureau of Mines project designed to unseal Colorado's rich but flooded lead, zinc, and manganese mines, is still being advanced, although the work is encountering severe difficulties. Work on the tunnel, begun in 1943, was dropped for lack of funds in 1945, and started again last September. The tunnel is one of the nation's toughest mining jobs. Fifty firms and individuals, who were asked to bid on the job of continuing be- yond the 6600-ft mark, didn't even answer. The work was finally taken over by the Utah Construction Co. of Salt Lake City. Since last September, the face has been moved 1000 ft closer to the flooded Leadville district mines, and to the hoped-for length of 17.300 ft. Some apparent success has already been noted, with an unusual decline in the water level in some major mine shafts reported this winter.

Jan 5, 1951

What has happened to the basic coal industry during the past year? Has it been a better year for coal than 1961? What striking new developments have occurred in mining, preparation and utilization? Are there positive signs that production will go up? What has happened in the utility market, the metallurgical market and the export market? Is the controversial question of coal transportation nearer to a solution? What progress has research made for coal during the year? The answer to these and many other important questions are offered in the following review of the Coal Industry-1962.

Jan 2, 1963

By C. Chamberlain

The Telfer Project, Australia's newest, largest, and most remote gold mine treats 480 kt of ore grading 9.33 g/t derived from open pit mining operations. Coarse gold is recovered by gravity concentration with jigs and further upgraded wing a continuous strake launder table, and by amalgamation. Remaining gold is recovered in a cyanide circuit and incorporates flat bottom air agitators, counter current decantation (CCD) and stellar filters for clarification and precipitate removal. Overall recovery into a bullion averages 98%. The mill incorporates a number of design features that allow for maximum efficiency and security wing a minimum number of operation personnel.

Jan 1, 1983

By Paul T. Benson

MOST important of the various departments of a custom smelter, so far as the financial welfare of the plant and the confidence of shippers are concerned, is that responsible for correct weights, accurate moisture sampling, and the obtaining of control samples that are strictly representative of the lot of ore from which they come. Treatment rate schedules are based on the metal content of ores received, reduced to dry weight. These rates must be low enough to keep the ship- per from taking his business else- where and still must allow the smelter a profit. Assay results, likewise, must satisfy the shipper, but if they show too high a metal content for the ore they represent, the smelter will actually lose money. It is always considered, and constant checks through umpire assays prove, that laboratory results are closely correct, so the bur- den of the plant profit and loss and the satisfaction of the shipper rest squarely upon the sampling department.

Jan 1, 1936

By Louis W. Huber

The Liberty tunnels extend through a very steep hill in Pittsburgh (locally called Mount Washington) for a distance of slightly over a mile. The two tunnels parallel each other and are 59 ft. apart, center to center (Fig. 1) They are for vehicular traffic, and in each there is ample space for two lines of vehicles. Northbound traffic, toward downtown Pitts- burgh, is confined to the east tunnel and southbound traffic to the west tunnel. The South Hills residential district is separated from downtown Pittsburgh by Mount Washington, a steeply rising escarpment south of and adjacent to the Monongahela River. The Mount Washington district immediately south of the Monongahela River has been reached, for many

Jan 1, 1927

By DAVID F. McFARLAND

THE making of courses of study and curricula has long held first place as the favorite pastime of educators. As a game, this activity is as fascinating to some as golf or bridge, 'and the golfer's hope of a low score is matched by the teacher's ambition to some day evolve a sequence of studies that shall prove the ideal preparation for a life of maximum service and, profit. There are few in, this gathering who have not tried their skill at this game and still fewer are those who have been long satisfied by the product of their efforts. A curriculum is hardly printed in the college catalog before conditions arise which seem to make changes desirable, and strong will power is needed to maintain the program long enough to give it a fair trial. Metallurgical curricula are not less subject to change than others, 'and; indeed they have seemed, at times, to change more rapidly than other curricula because of the changing 'needs of the industries and the demand that the graduate be trained to meet the new conditions. Metallurgical practice is constantly proving that "time makes ancient good uncouth," and the graduate metallurgist is required to adapt himself to newer and

Jan 1, 1930

By AIME AIME

THE following paragraphs comprise such information as the Secretary has been able to obtain concerning the members and associates whose deaths have been reported. Further particulars or corrections of errors, and biographical data concerning deceased members or associates not already noticed in this way, are solicited. Pat Doyle was born in 1849. At the age of fifteen he entered the Civil Engineering College of Madras, India, and left it at seventeen, having achieved special distinction in mathematics, chemistry,. and geology. Before be was eighteen years old he was in charge of two of the most important Sub-Divisions in the Madras Presidency, where he had ample opportunities for acquiring a preliminary knowledge of his profession, which was his chief object in joining the Public Works Department. In 1867, his energetic measures saved the island of Seringham from disastrous inundation. At this period he began contributing to the press ; and after a varied practical experience he came into public notice again in 1876, with an article in the Colliery Guardian on Indian Mines and Mining. In 1877 he became a Fellow of the Statistical Society of London. He was a founder of the Straits Branch of the Royal Asiatic Society and a life member of the parent Society of Great- Britain and- Ireland, as well as a member of the Independent Asiatic Society of Bengal. In 1878-9 he was Chief Superintendent of the Public Works of Perak; was active in having the Associate Member Class added to the Institution of Civil Engineers; and became a member of the Society of Engineers of London and of the North of England Institute of Mining and Mechanical Engineers. In 1880 he went to the Southern Colonies and held several appointments in Australia, where he became a member of the Johnsonian Club, Brisbane, and the Queensland Philo-

Jan 5, 1908

By Leo J. Miller

It is both an honor and a pleasure for me to be the keynote speaker for the Paul F. Kerr's Symposium on Applied Mineralogy. Professor Kerr was a man for all seasons to his students, and he treated all students as distinct individuals. Philip Bethke in his memorial to Dr. Kerr summed up our remembrance best by stating that "We have lost our most successful educator-administrator-scholar, who was our steadfast teacher-counselor-mentor-friend." His unique trait was the ability to bring out the best in a variety of individuals In order that their performance was at the peak of quality.

Jan 1, 1985

By Yu A. Chernegov

Building up the USSR's economic strength was the result of all the achievements and successes of our economy. The Soviet Union was the first to begin planned guidance of the economy. The mining industry of the USSR, which holds the first place in the world output of mining production, has always been considered as the main raw materials basis of the country's economy. High and stable development rates are a feature of planned economic management, based on the social ownership of the means of production. During the past ten years from 1965 to 1875 the national income used for consumption and accumulation increased practically by 1.9 times. There has been no inflation, no unemployment in the Soviet Union for about forty years already. High and stable growth rates of the production of mining industries and that of the branches, which are their direct consumers are characterized by the data in table I. The achievements and successes of the economy's development are to a great extent determined by the three planning components, which are as follows:

Jan 1, 1977

By R. W. Raymond

Recent literary labors have led me to the compilation of the following tables and estimates, which may possess interest for my colleagues in the Institute, and which are here submitted without comment.

By W. C. Leslie

The textures of cold-rolled and of annealed iron are compared with those of an iron-0.8 pct copper alloy in which the amount of precipitation after cold rolling was controlled. Previously published pole figures -for cold-rolled and for annealed iron are confirmed. The effects of precipztatiotz after cold rolling are to retain the cold-rolled texture after annealing, to inhibit the formation of the usual allnealing texture, and to produce elongated recrys-tallized ferrite grains. It is suggested that the inhibition of new textures by precipitation after cold rolling is a general phenomenon. A great deal of attention has been paid to the development of texture during the secondary or tertiary recrystallization of ferritic alloys, but very little work seems to have been done on the control of texture during primary recrystallization. If such control were attained, it might be possible to simplify the processing of oriented materials or to change the characteristics of current cold-rolled and an-nealed products. From previous experience, it seemed likely that texture could be controlled by recrystallizing a supersaturated solid solution. Green, Liebmann, and Yoshidal found that the formation of preferred orientation in aluminum (40 deg rotation about <111> relative to the deformed matrix) was inhibited when iron was retained in supersaturated solid solution in the strained aluminum. The authors attributed this inhibition to iron atoms in solid solution. There is, however, an alternative explanation. Green et al, took a highly supersaturated solution of iron in strained aluminum and heated it to an unspecified temperature for recrystallization. It is probable that precipitation occurred prior to and during recrystallization, and it is proposed that the inhibiting agent is this precipitate, rather than the iron atoms in solid solution. It is important to note that precipitation before cold work is ineffective; the effective precipitate is that formed after cold working and either before or during recrystallization. The location and distribution of the precipitate are critical. Precipitation in such a manner has been found to have profound effects upon kinetics of recrystallization and the microstruc-ture of the recrystallized alloys.2-4 It would be surprising, indeed, if this were accomplished with no change in texture. Because of the relative simplicity of the system, and because of previous experience,4-7 it was decided to determine the effect of precipitation on texture in an alloy of iron and copper. Bush and Lindsay5 found an unspecified change in texture in cold-rolled and annealed low-carbon rimmed steel sheets when the copper content exceeded 0.1 pct. MATERIALS In earlier work, the rate of recrystallization of a low-carbon steel was greatly decreased by 0.80 pct copper, and, after the proper treatment, the recrystallized ferrite grains were greatly elongated.4 Accordingly, it was decided to investigate the effect of precipitation on texture at this level of copper content. The iron and the iron-copper alloy were made from high-quality electrolytic iron and OFHC copper, vacuum-melted in MgO crucibles, cast, hot-rolled to 0.2 in., then machined to 0.150 in. The compositions are given in Table I. The plates were heated to 925°C and brine quenched, twice. This produced a ferrite grain size of ASTM 0 in the iron and ASTM 1 in the Fe-Cu alloy. Disk specimens were cut from the heat-treated plates, repeatedly polished and etched, then used to determine (110) and (200) pole figures by reflection. Despite the complication of large grain size, these pole figures strongly indicated a random texture. PROCEDURES The copper content in solid solution in ferrite before cold rolling and recrystallization, and hence, the amount that could precipitate during the recrys-tallization anneal, was controlled at three levels by heat treatment. The specimens as quenched from 925° C were presumed to have all the copper, 0.80 pct, in solid solution. Other samples of the quenched alloy were aged 5 hr at 700°C to retain about 0.5 pct Cu in solid solution.6 A third set of quenched specimens was reheated to 700°C, then slowly cooled in steps, to reduce the amount of copper in solid solution to a very low level. All specimens were cold-rolled 90 pct, from 0.150 to 0.015 in. thick. The rolling was done in one direction only, i.e., the strip was not reversed between passes, with a jig on the table of the mill to keep the short specimens at 90 deg to the rolls. The rolls were 5 in. in diameter and speed was 35 ft. per min. Machine oil was used as a lubricant. In a supersaturated alloy, the maximum effect of the copper precipitate on microstructure and on recrystallization can be developed by a treatment at 500°C, after cold rolling and before recrystallization.&apos;

Jan 1, 1962

By J. C. Bierlein, R. A. Dodd

Endurance strengths at 10&apos; cycles, fatigue-hardening rates, and endurance strength/0.2 pct proof stress ratios have been determined jbr a range of Cu(Ni), Cu(Si), and S.R.0. Cu(Au) solid solutions. Some douht is cast on simple cross slip models of fatigue hardening in view of opposite composition dependencies of hardening displayed by Cu(Si) and Cu(Au). The temperature dependencies of hardening also are the opposite of predictions made on the basis of a cross slip model. A correlation apparently exists between the fatigue strength/0.2 Pc~ proof s1.re.s~ ratios and rates of fatigue hardening. An increase in PS/PS due to alloying or temperature change is accompanied by a decrease in hardening rate, and vice versa. In recent years there has been much interest in the determination of the dislocation structure of fatigued metals and alloys. The accumulated evidence, e.g., Refs. 1 to 5, suggests that the structure may be dependent on the stacking fault energy, 7, of the fatigued metal in the same way that fatigue hardening rates have also been shown to apparently depend on u .6&apos; 7 The above research followed the various earlier theories relating crack nucleation to ease of cross slip, e.g., Refs. 8 to 131 so "ggesting that y may indeed be the parameter of principal significance in all facets of the fatigue process. However, comparatively little attention has been paid to correlating engineering fatigue data with observations of the above type. Certainly, it would be useful if potential engineering fatigue performance could be assessed from a knowledge of easily determined alloy properties, and the present research originated from this standpoint. TO investigate the widest Possible range of 7 would require the use of two solvent bases, e.g., aluminum and copper, but a reasonable coverage can be provided by copper-based solutions alone. Therefore, it was decided to work with Cu(Ni) and Cu(Si) solid solutions, the approximate stackillg fault energies of which are given in Table I. The y range extends from low, Cu(7.5 at- Pet Si), to moderately high in Cu(2-5 at. ~ct ~i) and two of the Cu(Ni) alloys. The values listed in Table I should be regarded as qualitative only, being derived as follows. Dillamore and smallman14 quote a value of 85 i 30 erg.cm-2 for the stacking fault energy of pure copper, based on an earlier value due to Howie and swannl5 corrected by Brown&apos;s formula.&apos;&apos; Since the ratios (alloy)h(pure copper) have been reported17,18 for Cu(Ni) alloys containing up to 30 pct Ni, approximate ) values for these alloys can be computed, and a rough estimate of 7 for Cu(50 at. pct Ni) obtained by extrapolation. The relatively low y value obtained in this way for Cu(50 at. pct Ni) coincides with the observation of Nakajima19 that the stacking fault probability is a maximum at this composition. Likewise, the y values for the three ~u(~i) alloys are estimates based on values given by Swann and Nuttingo corrected on the basis Of Brown&apos;s estimate that the true 7 values are probably 2.3 times greater than those originally computed. In addition to the above alloys it was decided to investigate short-range ordered (s.R.O.) CU(AU) alloys containing up to 25 at. pct Au. This last alloy has been shown to have a well-defined planar arrangement of dislocations when deformed,21,22 probably due to cross slip being restricted by the S.R.O. Engineering fatigue data was to be represented by the determination of endurance strengths, and these were to be correlated with fatigue hardening and mechanical property data. EXPERIMENTAL I, order to study the desired properties and property changes, the following alloys were prepared: Cu(2.5 at. pct Si), Cu(5.0 at. pct Si), Cu(7.5 at. pct Si), Cu(5.0 at. pct Ni), Cu(25.0 at. pct Nil, Cu(50.0 at. pct Ni), Cu(5.0 at. pct AU), Cu(15.0 at. pct AU), Cu(25.0 at. pct AU). The copper and gold were zone-refined, while the silicon was semiconductor grade. The nickel was of 99.95 p,t. purity.* All alloys were induction-melted in a *Kindly supplied by the International Nickel co. helium atmosphere, appropriate precautions being taken to avoid segregation in the Cu-Au series. Rod stock was obtained by rolling and swag,ng. A few Bridgman single crystals were grown for fatigue-hardening studies, but most material was machined into polycrystalline fatigue speciments of the design shown in Fig. 1, and into polycrystalline tensile and fatigue-hardening specimens of simple cylindrical design. All specimens except Cu(Au) were annealed; the latter were quenched from above T, to produce short-range order. A few of the quenched alloys were examined for long-range order by step-scanning over

Jan 1, 1969

By J. P. Hammond, C. J. McHargue

The wire textures for cold rolled and recrystallized iodide titanium and the sheet textures for this material produced by cold and hot rolling, and recrystallization at a series of temperatures were determined. &apos;The effect of the a + ß transformation on the sheet texture was noted. UNTIL recently it was believed that all hexagonal close-packed metals deformed by slip on the basal plane, (0001), and that rolling should tend to rotate this slip plane into the plane of the rolled sheet. The pole figures of cold rolled magnesium&apos; are satisfactorily explained on this basis. There is a tendency for the <1120> directions to align parallel to the rolling direction, and the principal scatter is in the rolling direction. Zinc% as a rolling texture in which the hexagonal axis is inclined 20" to 25" toward the rolling direction. Twinning is believed to account for the moving of the basal plane away from parallelism with the rolling plane. The texture of beryllium3 places the basal plane parallel to the rolling plane with the [1010] direction parallel to the rolling direction, and the scatter from this orientation is primarily in the transverse direction. Cold rolled textures reported for zirconium&apos; and titanium5 how the [1010] directions to lie parallel to the rolling direction and the (0001) plane tilted by approximately 25" to 30" to the rolling plane in the transverse direction. Rosi has recently reported that the mechanisms for deformation in titanium are distinctly different from those commonly reported for hexagonal close-packed metals. The principal slip plane is the prismatic plane, {1010), with some slip also occurring on the pyramidal planes, (1011). However, there is no evidence for basal slip. The slip direction is reported to be the close-packed digonal axis, [1120]. In addition to the twin plane commonly reported for metals of this class, {1012), Rosi found the twin planes (1122) and {1121), with the dominant twin plane being (1121). Information regarding the recrystallization and hot rolling textures of hexagonal close-packed metals is limited. Barrett and Smigelskas report that rolling beryllium at temperatures up to 800°C and recrystallization at 700°C produce textures not differing from the cold rolled sheet texture.3 McGeary and Lustman find that hot rolling at 850°C produces the same basic texture in zirconium as rolling at room temperature.&apos; These investigators also report that the texture for sheet zirconium recrystallized at 650 °C differs from the cold rolled orientation inasmuch as the [1120] direction, instead of the [1010] direction, is parallel to the rolling direction. In the case of titanium, it is not possible to deduce which direction is preferred in the recrystallized state from the pole figures presented by Clark." The purpose of this paper is to report an extensive investigation of the preferred orientations in iodide titanium. Since the deformation mechanisms for titanium are different from those commonly given for hexagonal close-packed metals, it is not surprising to find distinct differences between the textures of titanium and other metals of this class. Materials and Methods This investigation was carried out on iodide titanium obtained from the New Jersey Zinc Co. with an analysis as follows: N2, 0.002 pct; Mn, 0.004; Fe, 0.0065; A1, 0.0065; Pb, 0.0025; Cu, 0.01; Sn, 0.002; and Ti, remainder. The crystallities of titanium were broken from the as-deposited bar and melted to form 20 g buttons on a water-cooled copper block in a vacuum arc-furnace. Hardness tests conducted on the material before and after melting differed by only two or three Vickers Pyramid Numbers, indicating no or insignificant contamination. The buttons were hot forged, ground, and etched to sizes and shapes suitable for the rolling schedule, and vacuum annealed at 1300°F. Specimens for determination of the wire textures were reduced 91 pct in diameter to 0.027 in. in 24 steps using grooved rolls. In order for the orientation of the central region to be studied, portions of these wires were electrolytically reduced to a diameter of 0.005 in. using the procedure described by Sutcliffe and Reynolds.&apos; The sheet textures were determined on titanium cold rolled 97 pct to a thickness of 0.005 in. A reduction of approximately 10 pct per pass was used, and the rolling direction was changed 180" after each pass. Specimens used for determination of the recrystallized textures were annealed in evacuated quartz tubes at 1000°, 1300°, and 1500°F. The grain size of the 1000°F specimen was sufficiently small to give satisfactory X-ray patterns with the specimen stationary. However, it was necessary to scan the surface of the other recrystallized specimens. The microstructure of each annealed specimen was that of a recrystallized material. The diffraction rings all showed the break-up into spots typical of recrystallized structures.

Jan 1, 1954

By Thomas Varley

IN THE congressional act establishing the Bureau of Mines one of the functions outlined was "to assist I the industry in the prevention of mineral waste." This had not only to do with the waste in mining but in milling and metallurgical practices, including smelting. The organization of the Bureau of &apos;Mines includes many divisions, each working in a particular field and charged with certain investigative work. The metallurgical division has the above duties under its immediate supervision, and the station located at Salt Lake City is directed by the chief of this division: There are ten experiment stations of the Bureau of Mines, located in various parts of the country, most of them being housed at state universities under cooperative agreements. Considerable care was exercised in locating the stations and in choosing the particular type of work to be investigated at each place. Inasmuch as the Bureau was designed to serve and cooperate with the industry it is only natural that the investigative work be of interest and importance to the territory immediately adjacent to the respective stations.

Jan 1, 1925

By E. C. Bain

THE more familiar compositions of iron-carbon-chromium1 and the iron-carbon-tungsten2 systems have been investigated with a degree of thoroughness which has permitted the construction of their three-dimensional equilibrium diagrams; and it is probable that these equilibrium diagrams are sufficiently accurate for the present metallographic needs. Strangely enough, in spite of their importance, the alloys of iron, carbon and manganese apparently have not been investigated in the same systematic manner, and so far as is known, no three-component equilibrium diagram for this system is available. Even iron-carbon-nickel alloys3 have been studied rather more thoroughly; for these the solidus and liquidus surfaces have already been determined, but the solid transformations in this, as in the manganese system, have not been reported systematically. The present paper deals with the constitution at equilibrium of a series of 36 iron-carbon-manganese alloys of commercial purity limited by 1.5 per cent carbon and 15 per cent manganese, a range of compositions including most of the manganese steels. The temperature range of melting has not been determined, nor has the high-temperature (delta iron) ferrite equilibrium been included in the study, it being considered that the more important characteristics of the manganese steels are their ordinary transformations in the solid state. The delta iron region is almost certain to be a small tetrahedron not very different in magnitude or contour from that in the iron-carbon-nickel diagram. It is probably true

Jan 1, 1932

By Francis R. Conley, John A. Sievert, John N. Dew

A brief review is presented of the past performance of a number of large, thin, highly permeable reservoirs with low dips in the Bolivar Coastal fields of Venezuela. The performance of these reservoirs indicates that the fluids are segregated vertically within the sand section by gravity. With this assumption, equations are developed which describe the performance under pressure maintenance operations. Methods of solving these equations and results of simple example calculations are presented. Example calculations indicate that under pressure maintenance conditions injected gas tends to {tow preferentially along the top of the sands and that encroaching water has a tendency to flow preferentially along the bottom. The expected performance of segregated fluids is discussed and compared with that of fluids which are uniformly distributed in any sand section. INTRODUCTION The field performance of a number of reservoirs described herein indicates that the fluids are segregated vertically within the sand section by the force of gravity. Thus, it was felt that any method used to predict the future performance of these reservoirs should consider the effects of segregation in the sand sections. A study of the available information on some of the reservoirs suggests that increased recoveries may be expected if the reservoir pressure is maintained by either crestal gas injection or flank water injection. To predict future performance of reservoirs under pressure maintenance operations, a method of analysis was needed which would account for segregation of fluids in the sand sections. Several methods of analysis have been developed to take into account the segregation of fluids in the reservoir as a whole1,3 To our knowledge no method considers segregation of the fluids within sand sections in the manner indicated by the past performance of several reservoirs in the Mara-caibo Basin. This paper outlines part of the work done in studying some of these reservoirs and contains a description of their performance characteristics. The analysis presented is restricted to pressure maintenance conditions, since space limitations prevent a full discus- sion of the development of the mathematical relations and the various methods of solving them. Only a sketch of the development of the mathematical relations is given. The various methods of solving these relations are pointed out, but the actual determination of solutions to various problems are omitted except for one example. It is felt that these results may aid in the study of reservoirs outside the Maracaibo Basin. Some concepts on which the present analysis is based are outlined by D. N. Dietz. However, the analysis presented herein includes several factors not considered by Dietz: (1) variations in permeability and in the cross section, (2) various shapes of the cross section, and (3) the production of fluids. Also, the mathematical development presented by Dietz differs considerably from our corresponding analysis. RESERVOIR CHARACTERISTICS The reservoirs under consideration, large and thin, with low dip and high permeability, are large to the extent that they contain from 0.5 to over four billion bbl of oil initially in place. The section thicknesses vary from 100 to 400 ft and the lengths from 10,000 to 40,000 ft. Thus, a length-wise cross section of the producing formation appears to be long and thin. The dip angles vary from 0 to 6 degrees and the average permeabilities vary from 0.5 to over three darcies. The reservoirs contain from 20 to 50 per cent shale inter-laminated with the productive sands. Most shale breaks within the major sands do not correlate from one well to the next, and correlation is often difficult, even between wells drilled from the same location. However, it is often possible to correlate the shale breaks between major sands for some distance. Herein we are concerned with the performance of reservoirs containing oil of gravities over 20" API. Past reservoir performance indicates good pressure communication and, in cases where pressure sinks have developed, large amounts of fluid migration have occurred. Few of the reservoirs have had initial gas caps, but also, few have been found to be highly under-saturated. Due to gravity segregation, secondary gas caps usually form before the pressure has been reduced more than 25 per cent of its initial value. The effect of gravity has not only been apparent on a reservoir-wide basis, but has also caused segregation of the reservoir fluids in productive sections. Proof of this is found from the results of selective well tests, workovers, and electric and various other types of logs. Evidence that

By G. H. Bishop

The kinetics of the inter granular penetration and embrittlement of [100] tilt boundaries in 99.998 pct pure nickel upon exposure to bismuth-rich Ni-Bi liquids have been determined in the temperature range from 700° to 900°C. The kinetics of penetration are parabolic in time at constant temperature over most of the temperature range. In a series of 43-deg bicrystals the rate of penetration is anisotropic with respect to the direction of penetration into the grain boundaries. In lower-angle bicrystals the penetration rate is isotropic. The rate of penetration decreases with tilt angle at 700°C. The activation energy for penetration in the 43-deg bicrystals is 42 kcal per g-atom independent of direction. It is concluded that the intergranular penetration and embrittlement in the presence of the liquid proceeds by a grain boundary diffusion process and not by the intrusion of a liquid film. This was confirmed by a determination that the kinetics of penetration and embrittlement were the same in the 43-deg bicrystals upon exposure to bismuth vapor under conditions such that no bulk liquid phase would be thermodynamically stable. WhEN solid metals are exposed to a corrosive liquid-metal environment, the grain boundaries are sites of preferential attack. Depending on the temperature, the composition of the liquid, and the composition, structure, and state of stress of the solid, a number of modes of attack are possible. This paper reports a study of the kinetics of intergranular penetration and embrittlement of high-purity nickel bicrystals upon exposure to bismuth which, together with an earlier study by Cheney, Hochgraf, and Spencer,&apos; demonstrates that there are at least two modes of intergranular attack possible in the Ni-Bi system. In the study by Cheney et al., columnar-grain specimens of 99.5 pct pure nickel were exposed to liquid bismuth presaturated with nickel in the temperature range 670" to 1050°C. They found that the majority of the boundaries, which were predominantely high-angle boundaries, were penetrated by capillary liquid films, the attack proceeding by a process which will be termed grain boundary wetting. This process occurs in a stress-free solid when twice the liquid-solid surface tension is less than the surface tension of the grain boundary,* i.e., when 2yLs < YGB In this case the penetration of the grain boundary by the liquid occurs at a relatively rapid rate, resulting in the severe embrittlement of a polycrystalline solid. Grain boundary wetting is a common mode of intergranular attack in systems in which the lower melting component is relatively insoluble in the solid, but the solid has an appreciable solubility in the liquid, for example, the Ni-Bi system, Fig. 1. In systems of this type at temperatures above the range of stability of any intermetallic phases, once the liquid is saturated with respect to the solid so that no gross solution occurs, chemical gradients are small, and surface tensions become major driving forces for attack, provided the solid is stress-free. The results of Cheney et al. appear to be typical of those encountered when grain boundary wetting occurs.&apos; Capillary films were observed in the boundaries after quenching from the exposure temperature. The mean depth of penetration increased linearly with time, and the activation energy for the process was found to be 22 kcal per g-atom. In a study of the Cu-Bi system Yukawa and sinott4 found that the depth of penetration of bismuth into high-purity copper bicrystals of orientations from 22 to 63 deg of tilt about (100) at 649°C ranged from 0.05 to 0.25 in. after a 12-hr anneal. This corresponds to a linear rate of 6 to 15 X 10~6 cm per sec. At the same reduced temperature of 0.68 the rate for the Ni-Bi system&apos; was 7 x lo-&apos; cm per sec. In another study of the Cu-Bi system, Scheil and schess15 determined the kinetics of grain boundary wetting in hot-worked commercial rod. While there were several complicating factors present in this study, there is general agreement with the above results. The kinetics of penetration were linear, the activation energy was 20 kcal per g-atom, and at 650°C the rate of wetting was 2 to 5 x 10-6 cm per sec. The rate of wetting in the A1-Ga system6 is somewhat

Jan 1, 1969

By C. G. Dunn, J. L. Walter

Secondary recrystallization to the (110) [001] texture in high-purity silicon iron occurs if low-oxygen material is annealed in a nonoxidizing atmosphere. Any departure from these conditions results in a growth of (100) oriented grains. The nature of the matrix and secondary recrystallization structures and textures and the nature of grain boundary interactions during growth show that the low gas-metal interfacial energy of the (110) surfaces provides the driving force for growth of these grains. A type of grain growth, characterized by a driving force which derives from energy differences of {hkl} surfaces at the gas-metal interface, has been treated in recent papers.&apos;-7 Secondary recrystallization to the cube text!:: in high-purity silicon iron provides one example. The present paper also deals with a surface energy driving force but the texture that results by secondary recrystallization is not the cube texture; it is a texture in which the (110) plane is in the plane of rolling and the [001] direction is in the direction of rolling. The phenomenon described in this paper is different from the impurity (dispersed phase)-controlled secondary recrystallization process in which the (110) [001] oriented grains grow under the action of grain boundary driving forces.8-12 It is also different from tertiary recrystallization,2 which also produces the (110) [001] texture in high-purity silicon iron, since the matrix textures and grain sizes are different. Finally, it is unlike any other form of secondary recrystallization reported in the literature. The possibility of obtaining the (110) [001] texture in high-purity silicon iron became clear in a study of the effect of impurity atoms on the energy relationships of (100) and (110) surfaces. In this study Walter and Dunn6 observed the migration of (100)/(110) boundaries, i.e., boundaries between two grains, one of which has a (100) plane and the other a (110) plane, respectively, parallel to the plane of the sheet specimen. At 1200°C the (100)/(110) boundaries advanced into (100) grains in a vacuum anneal, then reversed their direction and migrated into (110) grains in a subsequent anneal in impure argon. Finally, the direction of migration reversed once again with (110) grains growing into (100) grains in a second vacuum anneal. These results were explained in terms of a change in concentration of oxygen atoms at the gas-metal interface during the anneals. Thus, oxygen atoms were added to the surface during the anneals in impure argon to the point where ?100, the specific surface energy of the (100) oriented grains, was lower than ?110, the surface energy of (110) oriented grains. In vacuum, however, the oxygen concentration at the surface was lowered to the point where ?110 < ?100. Concerning the possibility of secondary recrystallization in high-purity silicon iron with a low initial oxygen concentration, the observed effect of adsorbed oxygen atoms has indicated6 that a good vacuum anneal would favor the rapid growth of matrix grains with the (110) plane in the plane of the sheet much more than grains in the (100) orientation. The growth of only (110) oriented grains of course would depend upon y110 being less than ?hkl, where hkl refers to any plane different from (110). The present paper is concerned with the application of the above ideas to secondary recrystallization to the (110) [001] texture in high-purity silicon iron. The matrix and secondary recrystallization textures and structures are defined and discussed. Observations of growth of nuclei for secondary recrystallization and of boundary interactions are included to provide direct information on the surface energy relationships between (110) and other (hkl) surfaces. EXPERIMENTAL PROCEDURE As before, 2,4-6 high-purity iron and silicon were melted and cast in vacuum to provide an alloy containing 3 pct Si with less than 0.005 wt pct impurities. The oxygen content of the ingot was lower than in previous ingots, being approximately 3 ppm (by weight). The carbon content of this ingot may have been slightly higher than was found for previous ingots. The same rolling and annealing schedule used previously2 was followed in this study to obtain samples 0.012 in. (0.3 mm) thick. These samples were electropolished prior to annealing. After rolling and polishing, the oxygen content of the material was approximately 6 ppm; material used in the previous studies contained about twice this amount of oxygen.

Jan 1, 1961

By Sandford S. Cole, John S. Breitenstein

The recovery of over 80 pct of the vanadium values in titaniferous magnetite from Maclntyre Development,Tahawus, N. Y., was accomplished by an oxidizing roast with Na2O3-NaCI addition. Process description is given for leaching of roasted ore and precipitation of V2O5 and Cr2O8 from leach liquor. THE exploration and development of the Mac-Intyre orebody at Tahawus, N. Y., by the National Lead Co. provided a source of vanadium. Analyses of various composite sections of the drill cores of the MacIntyre orebody were made to establish whether or not the vanadium was constant throughout. Ten drill cores were sampled as 50 ft sections, crushed, and a portion magnetically concentrated. The head and concentrate were analyzed for total iron and vanadium. The results on the concentrates indicated that the vanadium is associated with the magnetite and maintains a close ratio to the iron content. The nominal ratio of 1:25:140 of V: TiO2:Fe was found to exist in the concentrates. Typical value for the vanadium in the magnetite both from laboratory concentration and mill production is 0.4 pct. The recovery of vanadium from the magnetite was investigated in 1942 to 1943. The research program encompassed both laboratory and pilot-plant work on sufficient scale to provide adequate data to establish the feasibility of a full scale plant. The recovery of vanadium from various ores has been reported in the literature and has been the subject of many patents. The literature dealing with recovery from titaniferous ore by roasting is quite limited. Roasting with alkaline sodium chloride, sodium chloride or alkaline earth chlorides, and sodium acid sulphate have been claimed in various processes as effective means.1-8 The reduction of the ore, followed by acid leaching, was another method proposed.&apos;-&apos; "he use of various pyrometallurgical processes for recovery of vanadium in the metal or in the slag has also been extensively investigated, but the results had little application to the problem."-" The separation of vanadium values from subsequent leach liquors and vanadium-bearing solution has been the subject of a considerable number of papers and patents. The most practical is by hydrolysis at a pH of 2 to 3 by acidifying a slightly alkaline solution. Data on solubility of V²O5 and V2O4 in water and in dilute sulphuric acid indicated a solubility of 10 g per liter in water.&apos;" Laboratory Results Magnetite Analysis: Adequate stock of magnetite was provided so that the laboratory and pilot-plant operation was on ore representative of the mill production. The ore was analyzed chemically and examined by petrographic methods to ascertain whether the vanadium was present in combined state or as an interstitial component between grain boundaries. No evidence was obtained which would indicate that the vanadium was in a free state as coulsonite.15 The analysis of the ore was as follows: Fe²O³, 47.4 pct; FeO, 29.1; TiO,, 10.1; V, 0.40; and Cr, 0.2. The screen analysis of the ore on the as-received basis was: -20 +30 mesh, 28.8 pct; —30 +40, 18.9; -40 +50, 9.7; -50 +60, 15.1; -60 4-100, 5.9; -100 + 200, 11.2; -200 +325, 3.7; and -325, 7.2. Roasting Conditions: The prior practice indicated that a chloridizing roast with or without an alkaline salt had been effective on other titaniferous magnetites. On this basis roasts with additions of sodium chloride, sodium carbonate and mixtures thereof were investigated varying the roasting temperature between 800" and 1100°C. Since the ore had shown no segregation or concentration of vanadium, the influence of particle size on the freeing of vanadium by the reagents during roasting was determined. The initial work was on silica trays in an electric resistance furnace with occasional rabbling of the charge. Subsequently, the roasting was carried out in a small Herreshoff furnace to establish the influence of products of combustion on the recovery of the vanadium. The laboratory tests showed that this ore required an alkaline chloridizing roast, in conjunction with a reduction in particle size to less than 200 mesh. When roasted in air at 900 °C with 5 pct NaCl and 10 pct Na2CO³, over 80 pct recovery of the vanadium was attained as a water-soluble salt. The presence of alkaline earth elements gave detrimental effects and care had to be exercised to avoid any contamination of the ore or roast product by such materials. The solubilization of vanadium under the various conditions is given in a series of curves in Figs. 1 to

Jan 1, 1952