Search Documents

By H. F. Yancey, O. L. Furse

Although usually coal is screened with punched plate screens having round-hole perforations, there has been an increasing use of wire-cloth screens with square apertures, especially at pneumatic coal-cleaning plants and at other plants that use vibrating screens. It is therefore desirable to establish a relationship between round-hole and square-hole screens for use not only in experimental investigations of coal-preparation problems, but also for use in commercial operations. This need is apparent whenever it is necessary to substitute wire cloth for punched plate and still retain the familiar trade-size product. Although similar work probably has been done by industrial organizations concerned with the screen sizing of coal, the only recorded study of the subject other than the one described herein of which the authors are aware is that of Roesler,1 who screen-sized two samples of limestone and two of zinc concentrates crushed to pass 1/2 in. with a set of square and round-hole screens and found the ratio to be 1:1.23. Procedure In the course of a study of various methods for determining the friability of coal,2 it was necessary to screen-size the products of a series of friability tests of three different coals with both round-hole and square-hole screens. The coals used were from the Roslyn No. 3 and the Bayne mines in Washington and the Rolapp mine in Utah. Twenty 25-lb. samples of each of these three coals at 3 to 2 1/2 in. round-hole size were dropped from a height of 10 ft. to a concrete floor, and then screened with

Jan 1, 1934

By Auguste J. Rosh

The use of titaniferous ores in the blast-furnace has been the subject of much controversy for many years. Divers objections have been raised against them, and, for one cause or another, the verdict

Jan 1, 1893

By T. G. Decker, A. F. Witt, A. M. Gaudin

The historical development of the concept of contact angle hysteresis is reviewed. The measurements of contact angles reported in literature have all been made under static conditions. For the measurement of dynamic advancing and receding contact angles, four methods are described together with an evaluation of their precision. Three of these methods were adapted from devices already used for the measurement of static contact angles. The fourth method uses a new principle and apparatus and is the most accurate. While the relationship between surface tensions and the contact angle was extablished as early as 1805 by T. Young,' it was only in 1890 that the existence of contact angle hysteresis was reported by Lord Rayleigh. His observations, however, remained almost unnoticed. With the invention of froth flotation, the contact angle and its behavior became the subject of investigation. In 1907, L. Sulman and collaborators investigated the cause of discrepancies between recorded values of contact angles. They found that certain variations existed in most cases, but that definite maximum and minimum values of contact angles are obtainable. The difference between the maximum and the minimum contact angle in a given system was termed "hysteresis" by Sulman. First attempts to explain hysteresis were made by E. Edser. In the following years extensive studies of contact angles in various three-phase systems

Jan 1, 1963

Jan 1, 1952

By A. C. Fieldner

THE older coal chemist had a much simpler conception of coal than we have today. To him coal was a mineral composed essentially of carbon, hydrogen, oxygen, nitrogen, sulfur, ash, and water, in various proportions. His studies on the constitution of coal were directed along the conventional lines of proximate and ultimate chemical analyses and making deductions from these data without any real appreciation of the fact that coal is a conglomerate of various chemical compounds, including many of the most complex structures known to organic chemistry. The view of the modern coal chemist is well expressed by Franz Fischer, I who says that while proximate and ultimate analyses are important both from the scientific and technical point of view, they tell the chemist no more concerning the number and kinds of chemical compounds that constitute coal than the reader would learn of the contents of a book if told that the printed contents consisted of 15 per cent. of the letter "e," 5 per cent. of the letter "n," 1 per cent. of the letter "g," 4 per cent. of the letter "b," etc. As the reader must have the grouping of letters into words and words into sentences, so the chemist must have the grouping of atoms into molecules and the proportion of each molecular compound in the coal aggregate before he acquires an adequate knowledge of the constitution of coal. Modern investigators2 are laying the foundation of a new chemistry of coal based on the biochemistry of plants and the chemical changes involved in processes of fermentation and decay. As

Jan 5, 1925

By R. H. Hawkins

An investigation of the applicability of geophyiical methods to northern Ontario lignite deposits was undertaken early in 1930 by the Ontario Research Foundation at the request of the Ontario Department of Mines Pre-Cambrian ... Syenite, granite gnciss, etc. Igneous intrusivcs . Lamprophyre dikes cut the Abitibi River and lover formntions. (Permission of Ontario Dept. of Mines) and was financed in part from a research grant made by the latter organization. The work to date has included gravitational, magnetic and electrical resistivity studies. The gravitational and magnetic measure-

Jan 1, 1934

By R. V. Ramani, Christopher J. Bise, Robert Stefanko

Over 200 billion tons of coal reserves lie locked up in deposits west of the Mississippi River-and of this, well over 100 billion tons are recoverable only by underground mining methods. Yet, because of the associated problems of unfavorable economics and inadequate technology, western underground mines contribute less than 2% to the annual US coal production. In order to reach the billion-ton coal production level called for by President Carter, it a pears the majority of new coal development will come from the West. But for this to be possible, new mining methods and equipment must be designed to match the unique thick seam conditions.

Jan 10, 1977

By M. E. Tyrrell, Alan H. Goode

The application of a simple, two-dimensional computer technique for evaluating rock burst potential in cut-and-fill stopes was investigated. The principal purpose of the study was to compare the effectiveness of high-modulus fill and destressing as aids in the control of rock bursts. Two conclusions that are probably of general applicability are drawn. First, high-modulus fill is ineffective as a means of increasing the mine stiffness and acts to control rock bursts only if it supports enough load to reduce substantially the stresses on the unmined vein material. Second, destressing is most effective if it is performed when the vein material is near the point of failure.

Jan 1, 1975

By A. K. Sinha

The market for thermal coal has recently been growing rapidly and it is projected to continue to do so in the foreseeable future. Both the national and international markets often demand high-Btu low-sulfur thermal coal in order to minimize the cost of utilization and meet the environmental restrictions. High quality thermal coal can be prepared to compete in the utility market by desulfurizing the high-Btu midwestern coal and blending it with low-sulfur western coal which is usually low in Btu content. The methods that can be used for optimizing the coal preparation plant operating parameters for physically desulfurizing coal are presented.

Jan 1, 1985

By J. D. Miller, A. Cortez, J. Hupka

The separation efficiency of the hot water digestion-flotation technique used for bitumen recovery from various domestic tar sands was evaluated. Bitumen viscosity was found to be the most important tar sand property in determining the success of the bitumen separation. Bitumen viscosity of the tar sand war controlled by changes in digestion temperature and/or changes in diluent (kerosene) addition. Complete and uniform dilution of the bitumen phase was achieved by providing a sufficient presoaking, or penetration time, for a given tar sand type. For all the tar sand samples tested, an excellent correlation was obtained between the coefficient of separation and the bitumen viscosity. To achieve a satisfactory coefficient of separation, it was found that the bitumen viscosity must be reduced below 1.5 Pa.s (16 P) at the temperature of digestion. This was the case regardless of the tar sand type, grade, or origin.

Jan 1, 1984

By Thomas S. Lovering

Hot springs, geysers, steam-emanating fumaroles- these creatures of nature were until recently little more than geological curiosities, but today they are exciting the interest of engineers around the world for it has been shown that such hyperthermal areas can be profitably harnessed by man to provide heat and power for his communities. Although water from hot springs was used centuries ago to heat some Korean dwellings, is being used today by one-third of Iceland's population for similar purposes, and is finding industrial applications in New Zealand and elsewhere, the most dramatic use of geothermal energy has been its conversion into electricity. The largest installation at the present time is that at Larderello, Italy, where the Count of Larderello began to experiment in the production of electricity from geothermal steam in 1904. Eight years later after a quarrel with the local power company, the Count installed his first steam turbine, a unit of 250 kw capacity.

Jan 9, 1965

Jan 1, 1969

The Institute is custodian of funds for support of numerous gold medals and prizes and has representatives on boards awarding still others. Details regarding the Institute Awards are given below. The Institute is represented on the boards of the John Fritz Medal, the Hoover Medal and the Washington Award, in connection with the three national societies of Civil, Mechanical and Electrical engineering; and, also, in the case of the Washington Award, with the Western Society of Engineers. The Institute is represented with these four societies on the committee in charge of the Alfred Noble Prize.

Jan 1, 1939

By J. A. Herbst, A. L. Mular

Digital simulation is defined and simulation techniques are re- viewed. Typical methodology involves the selection of models, the adjustment of raw data, the selection of a fitting strategy, the assessment of model accuracy in a statistical sense, and the development of an executive simulation structure. Simulations serve as aids for process engineers in evaluating the feasibility of a proposed flowsheet and the effect of a modification to an existing flowsheet. In addition, simulation plays an important role in off-line optimization and in the evaluation of alternative circuit control strategies. Several examples are presented to illustrate these uses for simulation including applications in crushing circuits, grinding circuits, and flotation circuits. It is the opinion of the authors that, within the next decade, mineral processing plants will be studied routinely via digital simulation during the preliminary design stage. Simulation will constitute an important component of the design decision making process.

Jan 1, 1978

[ ]

Jan 1, 1938

New Products Equipment

Jan 6, 1953

By A. R. Troiano, E. A. Steigerwald, F. W. Schaller

The initiation of localized cracking in hydrogenated high strength steel was dependent on the developmeni of a critical hydrogen conceniration and relatively insensitive to the magnitude of the applied stress. The stress was believed to influence the deluyed failure process by providing the means for grouping the hydrogen. On the basis of an assumed distribution law the observed changes in the lower critical stress as a function of notch acuity, yield strength, and temperature were predictable over a significant range of these variables. THE phenomenological characteristics of delayed failure in high-strength steel have been comprehensively investigated and the behavior has been attributed to the strong embrittling action of hydrogen.1-3 Delayed failure or, as it is also termed, static fatigue, is the most sensitive means of detecting hydrogen embrittlement since it allows the maximum time for hydrogen diffusion during a test.3 The nature of delayed failure cail be aptly described by four parameters which are schematically depicted in Fig. 1. The upper critical stress corresponds to the rupture stress in a conventional notch tensile test. The lower critical stress or static fatigue limit is the stress below which no delayed failure will occur. The incubation period is the time required for the formation of the first crack and the fourth parameter is the failure time. An increase in hydrogen content, notch acuity, or strength level of the material increases the susceptibility for delayed failure by decreasing the lower critical stress, the incubation period, and the time to failure.lY3 A decrease in test temperature prolongs the incubation period in accordance with the lower diffusion rate of hydrogen, and also de-

Jan 1, 1961

By J. Charles Miller

THE expansion of facilities for rapid transportation of perishables by train, truck and airplane has necessitated consideration of refrigerants of a minimum weight and volume per pound of cooling and has stimulated the use of solid carbon dioxide commercially. The gas probably has not had wide application in the past in air-cooling equipment for mines, theaters or buildings, owing to its thermodynamic properties, as will be deduced from examination of Table 2. However, consumption of the liquid in carbonating beverages remains a dominant factor. In addition to these uses, carbon dioxide is employed to a limited degree as an explo-sive in the liquid form, as a freezing agent in plumbing, in laboratories for low-temperature work, and in the manufacture of golf balls.

Jan 1, 1936

By R. Woods

INTRODUCTION Gaudin (1), considered that "the mechanism of mineral collection is the central problem of flotation theory". From their work on adsorption phenomena in flotation for more than fifty years (2), Gaudin and his co-workers have made major contributions to the elucidation of this mechanism, a fact acknowledged by their contemporaries in the field (e.g. (3)). Their investigations in a number of areas, e. g. demonstrating that submonolayer quantities of adsorbed collector species can induce flotation, or identifying the influence of substances which can activate or depress (1), have helped to provide the basis for and the development of a theory to account for the interaction between mineral and collector. It was established in the late fifties (4) that the presence of oxygen is a prerequisite for the flotation of metal sulfides with thiol collectors. This fact rendered inadequate the concept of simple ion adsorption being responsible for rendering these minerals hydrophobic. The requirement for oxygen has been explained (1) in terms of this species being a component in chemical reactions between the sulfide surface and the collector. Gaudin has been instrumental in identifying the products of chemical reactions at sulfide minerals (1, 5), a line of work which has been continued particularly by Finkelstein and co-workers in South Africa (6). In presenting a detailed mechanism of the mineral-collector- oxygen interaction, it has often been considered that the mineral surface [must] first be oxidized to a metal oxy-sulfur species which

Jan 1, 1976

Jan 1, 1908