Search Documents

By S. Floreen

Seven iron alloys ranging from 5 to 12 pct Ni and 5 to 14 pct Cr were studied. All alloys transformed to bcc massive martensites. Tempering increased the strengths , probably because of relief of residual stresses generated by the martensite transformation. The major strengthening mechanism appeared to be solid-solution hardening by nickel and chromium. Studies of the work-hardening behaviw, of the effects of prior austenite grain size, and of the effects of changing strain rate and test temperature gaue results very similar to iron or low-alloy steels. Increasing nickel contents markedly improved the toughness at subzero temperatures. Studies of the flow properties did not, however, indicate the reason for the beneficial effect of nickel on toughness. The marine atmosphere corrosion resistance of the alloys was improved primarily by chromium additions, but increasing nickel contents were also beneficial at low levels of chromium. J\ number of maraging and PH stainless steels are strengthened by precipitation hardening in a low-carbon Fe-Ni-Cr martensite matrix. To some extent the resultant properties of these steels must depend upon the properties of this matrix. The present study therefore was conducted to evaluate the transformation characteristics and mechanical properties of a series of Fe-Ni-Cr martensitic ternary alloys. A limited evaluation of the corrosion resistance of the alloys in marine atmosphere was also made. ALLOY PREPARATION Seven 100-lb air induction melts were prepared using electrolytic iron, nickel, and chromium metal additions. The initial Fe-Ni charge also contained 0.05 wt pct graphite to produce a carbon boil during melt down. After melting of the base charge, the heats were refined with 0.1 wt pct additions of manganese, silicon, aluminum and titanium and poured into cast-iron molds. The ingots were homogenized at 1250°C and uni-directionally hot-rolled to 2-in. plate. They were then homogenized another hour at 1250°C, and unidirection-ally hot-rolled to %-in. plate at a finishing temperature of approximately 1050°C. The compositions of the heats are given in Table I. Two additional heats were prepared as 40-lb vacuum-induction melts using electrolytic iron, nickel, and chromium metals, and commercially pure molybdenum chips. A carbon boil, and 0.1 wt pct additions of aluminum and titanium were again employed, but manganese and silicon were not added. The heats were converted to %-in. plate using the procedure described above. The compositions of these heats are included in Table I.

Jan 1, 1967

By W. McA. Johnson

The work of J. E. Johnson, Jr., on the effect of small amounts of oxygen in cast iron in increasing its strength and resistance to shock, is of interest from the technical and scientific standpoints. The following exposition of the theory carries Mr. Johnson's explanation further and, in my opinion, will disclose certain related phenomena and perhaps shed further light on the subject. Some facts, so novel in character as to excite incredulity, have been accepted finally by many metallurgical authorities. One of these is that oxygen to the amount of 0.060 per cent. in cast iron gives it a breaking strength of 3,500 Ib. per square inch, compared with a breaking strength of 2,500 lb. per square inch in cast iron of the same composition with respect to elements other than oxygen, but having only 0.010 per cent, oxygen. The "oxygenated" cast iron, even if made in a coke furnace, has properties equivalent to the best charcoal pig iron. Mr. Johnson has also established the fact that the variations in combined carbon cannot account for the results. By microphotographic evidence he has shown that in oxygenated cast iron the graphite particles are dense and spherical, while in well-deoxidized cast iron the graphite particles are flaky and leaf-like. It is just a matter of common sense that iron of the latter structure is much weaker than the former. The analytical and microscopical work has been done with care and there is no doubt in my mind about the accuracy of the experimental results. In this paper then, we shall consider it as accepted that small amounts (0.060 per cent.) of oxygen increase the strength of cast iron by producing a structure in which the round and solid particles of graphite are surrounded firmly by a principal matrix of ferrite. The purpose of this paper is to show that the reason why the graphite particles are round is founded on the fact that the particles of any precipitate are made denser and harder by the presence of a reagent having a solvent action on the precipitate. This can be stated as a law, although I have never seen it so given in any textbook. Let us then, for purposes of illustration, give a concrete example and develop the theory of such mechanical and chemical actions as occur: It is well known that, by a soluble sulphate, a barium salt in solution is precipitated in a dense and easily filtered body when the solution is

Jan 1, 1916

By G. Thodos, E. M. Phillips

A reduced density correlation for the gaseous and liquid regions of ethane has been developed from all the experimental PVT data available in the literature for this substance. Saturated vapor and liquid densities reported for methane, propane and n-butane were utilized to establish the rectilinear-diameter line for ethane. This line was then used with the saturated-vapor data for ethane to produce the saturated envelope for this substance. Most of the saturated liquid data reported for ethane were found to be inconsistent with the saturated-liquid curve resulting from this study. The correlation covers the regions 0.65 < TR <6.0 and 0 < PR < 15. For regions for which no experimental data have been reported, the isobars of the correlation were extended by the use of the theorem of corresponding states. This correlation is presented both on rectilinear and log-log coordinates. INTRODUCTION At the present time, there is considerable interest in the exact PVT behavior of pure hydrocarbons. Matschke and Thodos12 recently have developed a comprehensive compilation of experimental vapor and liquid density data for methane. Similar studies have been conducted for other pure substances.4, 7 In the present study the density data available in the literature for gaseous and liquid ethane have been critically reviewed and utilized to develop a reduced density correlation for this substance. SATURATED LIQUID AND VAPOR DENSITIES The rectilinear-diameter rule proposed by Cailletet and Mathias5 states that the sum of the saturated liquid and vapor densities of a pure substance is a linear function of temperature which passes through the critical point. This law, although empirical, has been well established by continued verification since its conception in 1886. This rule has been applied to the saturated density data of methane,6 propane 17 and n-butane8 to produce the straight lines presented in Fig. 1 which pass through the critical point TR = 1.00, Pr = 2.00. The rectilinear-diameter relationship for ethane was established from the lines for the other substances in Fig. 1 by plotting the quantity p~, + PR against zc for different reduced temperatures. A critical analysis of the saturated vapor and liquid densities reported for ethane by Kuenen,10 Maass and McIntosh,11 and Sage, Webster and Lacey18 revealed that the values of PR1 + pr resulting from these studies were inconsistent with the rectilinear-diameter line obtained from the reliable density data of the other substances, as shown in Fig. 1. In the analysis of these data, reduced quantities were calculated using the critical con-

By Roscoe C. Clark

A study of the effect of various corrosive waters on five different types of cements indicated that those cements containing less than 5 per cent tricalcium aluminate were the most resistant to corrosion. INTRODUCTION Oil field experience indicates that some formation waters are excessively corrosive to some cements. A study has been made to determine the most corrosive waters and the relative resistance of various types of cement to these corrosive waters. PROCEDURE This study of the corrosion of cement was limited to an evaluation of the effect of various corrosive waters on five different types of cements. A determination was made of the types of cements which offer the greatest resistance to corrosion and of the chemical contents of waters found to be the most destructive to cements. The laboratory tests were conducted by immersing small cylinders of 20 samples of set cement in various corrosive waters. The initial mixing of most of the cement slurries was done using Tulsa tap water as the mixing water; however, a few of the slurries were mixed using a sulfate water as the mixing water. When the 20 samples had been immersed for a period of nine months, they were removed from their corrosive baths, inspected and photographed. The field tests were conducted by placing ten cement specimens, each contained in a screen wire thimble, in the gas anchors of insert pumps in wells in six different fields. The specimens were observed whenever it was necessary to pull the pumps and were returned to the 1aboratory when deterioration had reached a serious state. EXPERIMENTAL RESULTS In both the field and laboratory tests the resistance of the different cements to corrosion was determined by the condition of the samples and the number of samples of each that were in good condition at the end of the immersion period. Table I lists the various cements tested in the order of their resistance to corrosion with the most resistant at the top and the least resistance at the bottom. An analysis of Table I reveals that the upper half of the table predominates in slow set and sulphate resisting cement.: (low 3CAO.A12O3 content) while in the lower half the port-land and high early strength cements are in the majority. Of the last two the high early strength cements appear to offer less resistance to sulfate water corrosion. An investigation of the composition of the cements listed in Table I indicated that as a general rule the cements containing less than five per cent tricalcium aluminate will exhibit the greatest resistance to corrosion. The destructive action of various corrosive waters was compared by listing the waters in the order of those containing the largest number of samples that failed completely. These ratings are presented in Table II with the most corrosive waters listed first and the least corrosive last. Figs. 1 and 2 show the end views of cement samples which had been immersed in the baths of five per cent MgSO, water and the five per cent Na2SO4 water respectively in the laboratory. These .pictures are representative of the results obtained and present a pictorial evaluation of the corrosive resistance of various types of cements.

Jan 1, 1950

By D. Weinstein

The high temperature mechanical properties of stainless steels after fast neutron irradiation are discussed in the light of effects caused by lattice dattmage and effects caused by helium generated from n,a transmutations. Embrittlement at high temperatures is due to helium accumulation at grain boundaries and to cavity formation and proPagation along grain boundaries. Following from the embrittlement mechanism, it is suggested that when deformation occurs by mechanisms associated with super plasticity, helium ac-curnulation at boundaries should be attenuated and cavities, if formed, should be nonpropagating. As the mean free Path between interphase boundaries of a two-phase Fe-Cr-Ni alloy was decreased, the degree of superplastic deforrnation at 870°C increased, as vneaszired by total elongation and by the expottent m = a log &apos;a/a log &apos;i. This alloy and type 304 stainless steel were cyclotron irradiated in an a-particle beam to a helium concentration of -1 x 10 atom He per atom. The stainless steel specimen was embrittled, but the ductility of irradiated two-phase Fe-Cr-Ni alloys correlated with the values of. m during &apos;defor-malion. The .finest grained, helium-injected specimens that deforrned with highest m values exhibited the largest elongations to ,fracture. These results could be correlated with metallographic observations of cavity behavior: the propensity for intergranular propagation was lessened as the m value increased. It is concluded that superplastic deformation is ef-fectizle in attenuating helium embrittlement at elevated temperatures. One of the principal problems associated with development of fast breeder reactors is application of alloys such that suitable fuel cladding results. Stainless steels and other Fe-Cr-Ni alloys, because of highly acceptable nuclear characteristics, represent the primary materials for this component, and an exhaustive research and development effort is being conducted. The main deficiency of these materials has been a severe loss of ductility at high temperatures after fast neutron irradiation. An extensive body of mechanical property data and microstructural observations has provided an adequate phenomenological description of embrittlement; in conjunction with transmission electron microscopy studies, a reasonably acceptable embrittlement mechanism has been obtained. Following from this mechanism, it is suggested in the present work that ductility would be enhanced if deformation could occur by mechanisms associated with the phenomenon of superplasticity. Experiments to test this hypothesis have been conducted, and the results are presented and discussed in this paper. IRRADIATION EMBRITTLEMENT AT HIGH TEMPERATURE Austenitic stainless steels have been irradiated to accumulated fast neutron fluences of 1020 to 1022 nvt at temperatures between 60" and 600°C. Specimens that have been exposed to these conditions and subsequently tensile tested at temperatures between 600" and about 900°C exhibit approximately 5 pct total elongation to fracture.&apos;-3 For unirradiated specimens receiving a nearly identical thermal exposure, total elongation at these test temperatures is about 45 pct. Examination of irradiated specimens has shown that fracture propagation is entirely intergranular. These phenomenological aspects of irradiation embrittle-ment at elevated temperatures are well known and are not generally disputed. Although the explanation of this phenomenon has been controversial, a mechanism for ernbrittlement has emerged that accounts reasonably well for the observed mechanical behavior. The controversy resulted primarily from an indeterminate role of neutron-in-duced lattice damage, if any, and a presumed, but experimentally unverified, contribution to embrittle-ment from helium generated by n,a transmutations. Recently, Holmes and coworkers4 have conducted experiments that separate these effects, and the results are instructive in formulation of the ernbrittlement mechanism. Holmes el al.4 irradiated type 304 stainless steel in EBR-I1 to a fluence of 1.4 x 1022 nvt (E > 0.18 mev); the irradiation temperature was 538" * 48°C or, in terms of absolute melting point, 0.49 * 0.03 T,. After irradiation, tensile tests were conducted at temperatures of 21" to 870.C, the specimens first being annealed for 30 min at each test temperature. In addition, thin sections of irradiated specimens were annealed for 1 hr at identical temperatures, electro and examined by transmission electron microscopy. Thus, for a given temperature, it was possible to correlate mechanical properties with the defect structure. At room temperature, the yield stress of irradiated specimens was a factor of 2.5 higher than unirradi-ated specimens exposed to an equivalent thermal history. Electron microscopic examination of the irradiated specimen revealed a high density of lattice damage in the form of Frank sessile dislocation loops and polyhedral voids. Holmes et al.4 concluded that the presence of this defect substructure caused the increase in yield stress and that after irradiation in a fast neutron flux at 0.49 Tm, substantial lattice dam-age persists. Annealing at progressively higher tem-

Jan 1, 1970

By G. R. Speich, S. A. Kulin

The isothermal formation of martensite at subzero temperatures has been studied in an austenitic stainless steel. The amount of martensite formed isothermally in a given time was found to follow a C-curve behavior with decreasing temperature. Since isothermal rnartensitic transformation occurs at temperatures above the true M. temperature of the olloy, the observed M. temperature is dependent on the cooling rate. It is believed that a general martensite theory must include the basic concepts of the strain embryo theory, and also the important role of thermal fluctuations. UNTIL recently the isothermal component of the martensitic transformation had been considered as a trivial effect in theoretical considerations of this type of transformation. One of the postulates used in defining a martensitic transformation was that the reaction was temperature dependent but not time dependent. Cohen and his associates1&apos;2 were the first to report the isothermal formation of mar-tensite. They obsel-ved the time dependency of the martensite reaction at room temperature in plain carbon steels and certain tool steels. They found that a small amount of additional transformation occurred after the specimen reached the quenching temperature and that the rate of this isothermal transformation decreased rapidly with time. These authors considered this phenomenon to be a "tailing-off" of the main athermal reaction. Kurdjumov and MaksimovaL 5 studied the isothermal formation of martensite at subatmospheric temperatures in steels containing 0.6 pct C-6 pct Mn, 1.6 pct C, and in an iron-base alloy containing 23 pct Ni and 3.4 pct Mn. In each case it was found that both the initial rate and the total amount of isothermal transformation exhibited sharp maxima with decreasing temperature. They stated that it was possible to completely suppress the martensitic transformation in the 0.6 pct C-6 pct Mn steel by drastic quenching in liquid nitrogen. They interpreted their results in terms of a thermally activated process. The maximum in the rate of nucleation vs. temperature curve was assumed to be a result of the temperature dependence of the rate of growth of the martensite plates. It has been demonstrated," however, that martensite plates can form with great rapidity even at temperatures approaching absolute zero. In addition," attempts to confirm the reported suppression of the martensitic transformation by rapid cooling of a 0.6 pct C-6 pct Mn steel have proved unsuccessful. On this basis, and on other theoretical grounds, the validity of some of Kurd-jumov&apos;s results and conclusions is open to serious question. Cohen, Machlin, and Paranjpe&apos; have proposed a theory of martensite formation based on the nucleation of strain embryos and a growth mechanism involving cooperative atomic displacements. According to this theory thermal fluctuations can make a strain embryo supercritical and thereby produce martensite isothermally. Das Gupta and Lement&apos; have investigated the isothermal formation of martensite in a 17 pct Cr-0.7 pct C steel at temperatures below the ambient. They found that partial suppression of the martensitic reaction occurred on quenching into liquid nitrogen. That part of the reaction which can be suppressed is taken to correspond to the isothermal rather than the athermal part of the rnartensitic transformation. The initial rate of isothermal transformation for this steel was found to go through a maximum with decreasing temperature. This is in conformity with the findings of Kurdjumov and Maksimova for the steels used in their investigation. Das Gupta and Lement conclude that isothermal martensite formation occurs by the nucleation of new plates and is always preceded by some athermal transformation. An iron-base alloy containing 14 pct Cr-9 pct Ni was used in this investigation to study further the kinetics of the austenite to martensite transforma-

Jan 1, 1953

Alexander N. Winchell, Butte, Mont. (communication to the Secretary): Mr. Spurr calls attention to the fact that an ore-deposit may be due to a succession of concentrations at different geological epochs. He cites an example of such a condition on Napoleon creek, a branch of Forty-Mile creek, Alaska. It will perhaps be of interest to call attention to another example of the same general character, not so remotely situated. The example referred to is located on Pole creek, a tributary of Cherry creek, in the extreme northeastern part of Madison county, Montana. An excellent geological map of this region is to be found in the Three Forks folio (No. 24) of the United States Geological Survey. According to this map, Pole creek, in its upper course, occupies the contact between the " Flathead " formation, which Peale correlates with the Middle and Lower Cambrian, and an area of gneisses and schists supposed

Jan 1, 1903

By E. E. Underwood, L. L. Marsh

Aluminum single crystals, alloyed with 0.042 atomic pet Cu and 0.11 and 1.1 atomic pct Mg, were subjected to constant stress creep tests, tensile tests, and hot hardness measurements within a temperature range of 300° to 866OK. Calculations based on Dorn&apos;s temperature-compensated time parameter, 6, gave a value of DH, = 27,000 cal per mol for the activation energy of early creep in aluminum single crystals. Correlations have been obtained for aluminum alloy single crystals with the parameter E for solid solution strengthening, as well as with the parameter F for solid solution hardening, by using a valence of three for aluminum. Limited measurements on tensile specimens show that the slip band density tends to decrease with increasing temperature and with decreasing solute concentration. INCREASING interest is being shown in the mechanisms of plastic deformation in single crystals during tensile and creep testing. The complexity of deformational processes in polycrystalline materials has led to a search for simpler experimental conditions. Numerous creep and tensile investigations have been conducted with pure, metallic single crystals. To a lesser degree, the effects of alloying elements on the tensile properties of single crystals have been determined. However: the literature dealing with the effects of alloying additions in single crystals under creep conditions is vanishingly small. This paper represents an attempt to narrow this gap in the knowledge of the subject. Previous investigations of creep behavior at the Battelle Memorial Institute1-1 have been of great value in the analysis of the present single crystal data. It is equally desirable, however, to ascertain the extent of correspondence between the behavior of single crystal and polycrystalline materials. For this purpose, correlations, similar to those developed for polycrystalline aluminum alloys by Dorn and co-workers, have been made with the single crystal data. The results from this study have tended to confirm and extend those correlations to the case of alloyed single crystals. Materials and Procedures Three dilute binary aluminum alloys were prepared for this investigation from 99.99 + wt pct Al, 99.8 wt pct Mg, and 99.92 wt pct (electrolytic) Cu. The nominal compositions of the alloys were 0.042 atomic pct Cu, and 0.11 and 1.1 atomic pet Mg. Precautions were taken to avoid contamination of the stock during melting and casting of the alloys. After a heat treatment of 8 hr at 925°F the alloys were extruded, then machined into) threaded tensile specimens with a 3 in. reduced section and a 0.505 in. diam. Spectrographic examination showed less than 47 ppm metallic impurities in each alloy. The single crystals were grown by the strain-anneal method, with a critical strain of about 11/4 pet giving the optimum results. In general, 3 in. crystals were obtained with the Al-Cu alloy, but smaller crystals in the magnesium alloys necessitated the use of 2 in. and 1 in. gage lengths with the low and high magnesium alloy specimens, respectively. After an electrolytic polish, the orientation of that portion of the specimen containing the largest single crystal was determined from Laue back-reflection photographs. Tensile tests were conducted at a constant load rate of about 2 lb per min. Creep runs were made in a constant temperature room, under constant stress at the higher creep temperatures, and constant load at the lower temperatures. The eloneation was measured to within ±5 microin. by a specially designed capacitance extensometer. The ex-tensometer arms were attached to the 3 in. specimens at the shoulders of the test piece or, where the crystals were smaller than 3 in., by knife-edge grips.

Jan 1, 1957

By C. H. Li, J. A. Sarteli, W. Bonfield

The stress to cause a permanent micros train of 2 x 10-6 in. per in. (defined as the microscopic yield stress) in beryllium is found to be very sensitive to surface condition. The initiation of plastic flow in as-machined specimens, which contain a high density of twins and large residual compressive stresses to a depth of about 0.010 in. from the surface, occurs by the nucleation of slip from high stress fields around twin tips in the surface layers. Removal of the damaged surface layers by chemical polishing results in an appreciable increase in the microscopic yield stress, which is attributed to the remoual of stress raising twins rather than to the release of residual stresses. IT is well known that the macroscopic mechanical properties of beryllium are very sensitive to the nature of its surface finish. Matthews and coworkers1 have shown that the tensile strength of rolled beryllium sheet can be considerably enhanced by chemical polishing, presumably due to the removal of the high concentration of notches, twins, and large residual compressive stresses normally found in the surface layers of ground specimens. There was no similar effect of surface condition on the macroscopic yield stress (the stress to produce 0.2 pct strain), a point to which we shall return. To date there have been no extensive studies on the effect of surface condition on the microstrain region of beryllium. Recent measurements2 of the stress to cause a permanent microstrain of the order of 10-6 in. per in. on machined hot pressed QMV beryllium, gave values ranging from about 600 to 3500 psi. Reasons for the considerable scatter in the results were not discussed. In this paper, we wish to show that the microstrain region of polycrystalline beryllium is, in fact, very sensitive to surface condition. The stress to cause a permanent strain of 2 x 10-6 in. per in. which for convenience we will refer to as the microscopic yield stress, can be increased by almost a factor of 2 by minimizing the amount of surface damage. The variation of microscopic yield stress is attributed to the presence of twins in the surface layers, rather than to residual compressive stresses. EXPERIMENTAL PROCEDURE The starting material for this investigation was commercial purity hot pressed QMV beryllium, with an average grain size of about 20 . The effects of surface treatment were assessed by comparing the microstructure with residual stress measurements and microstrain properties. Specimens were prepared for metallographic examination by wet grinding with 240, 400, and 600 papers, followed by polishing with a suspension of fine alumina in warm 20 pct oxalic acid. After this treatment, the surface could be examined, either in the unetched condition with polarized light, or after etching in 2 pct hydrofluoric or boiling 20 pct oxalic acid with normal light. Thin films of beryllium suitable for electron transmission study were prepared from bulk specimens by chemical polishing with hydrofluoric and phosphoric acids, and were examined in an RCA-EMU-3 electron microscope. Residual stress measurements were made by a procedure similar to that of Treuting and Read.3 Specimens 4.0 in. by 0.625 in. by 0.080 in. were prepared by three different machining procedures, namely: turning, grinding, and sawing, in order to introduce different levels of residual stresses. An electrical resistance strain gage was attached to one side of the specimen, and that surface was then protected by an acid-resistant enamel, while the opposite surface was removed by etching approximately one thousandth of an inch at a time. The change in specimen curvature in the longitudinal direction was noted and the residual stress was calculated by the following formula:

Jan 1, 1963

By R. A. Graham, R. W. Rohde, J. R. Holland

In a shock wave compression study of a martensitic Fe-30 pct Ni alloy, Graham, Anderson, and Holland&apos; found a region of unusual compressibility extending from a few kilobars up to about 20 kbars. This region was characterized by a continuously decreasing shock wave velocity with increasing stress. In this note, we report the results of a study initiated to determine the source of this unusual compressibility. In earlier shock-loading experiments on martensitic Fe-30 pct Ni, Loree et a1.&apos; determined that a phase change occurred at about 80 kbars. Subsequently, Bowden and elly found that samples of a similar material shock-loaded at about 100 kbars experienced a martensite-to-austenite transition. Their crystal-lographic analysis showed the transition was a direct reversal of the established martensite system to the austenite phase. The shock loading in the present experiments was accomplished by precisely controlled plane impact between two discs of the sample material. This configuration created a state of uniaxial strain in the two the front of a projectile which was accelerated to various velocities. Planarity between the impacting discs was controlled to 5 x 10-4 rad, and impact velocities were measured to 0.5 pct. From a knowledge of the Hugoniot relationships of the material and the impact velocity, the shock-wave stress can be calculated. Samples were shocked at 18, 50, 70, and 100 kbars. The specimen discs shocked at 18 and 50 kbars were instrumented with quartz gages to observe the stress time profile. A more detailed description of the experiment has been given previously.4 The shock-loaded specimens were recovered intact by decelerating them in a catcher filled with soft wood. Discs of Fe-30 pct Ni nominally 12.7 mm thick and 64 mm in diam were cut from bar stock. Chemical analysis of the material provided the following composition in weight percents: 29.5 Ni, 0.50 Mn, 0.21 Si, and 0.10 C, with traces of Cr, Cu, Mo, Al, and Co. The discs were austenitized at 650° C for 2 hr at a pressure of less than l0-&apos; torr, and furnace-cooled. Martensite was then produced by quenching the discs at -196" and holding 168 hr. The initial martensitic structure formed is shown in Fig. l(a). Typical microstructures of samples shock-loaded at 18 and 100 kbars are shown in Figs. l(b) and l(c). The banded structure with the austenite regions running parallel to the shock propagation direction was characteristic of samples shock-loaded at all stresses. No such banding was found in samples that were not shock-loaded. Comparison of Figs. l(b) and l(c) shows that, although under the optical microscope the two microstructures are quite similar, the martensite plates of the specimen shocked at 100 kbars etched in a distinctly different manner. This unique etching behavior of martensite in samples shock-loaded above the 80 kbar transition point has also been observed by Leslie el al.&apos; These investigators determined from X-ray and electron microscope studies that fcc martensite, similar in appearance to normal bcc martensite, had been formed under shock loading. A quantitative determination of the amount of austenite present after shock loading was made by X-ray techniques. Both the methods of Lindren&apos; and Miller&apos; were utilized. The results are shown in Table I. The error limits are those experimentally observed from two independent analyses of each sample and represent the precision of the experiment. The absolute error, which should be similar for each sample, is believed to be about 10 pct. It is seen that as the shock stress increases the amount of austenite present also increases. On the basis of the X-ray and microscopic observations, we conclude that shock loading below the 80 kbar ersal will initiate a martensitic reversal: the amount of reversal that occurs increases with in-

Jan 1, 1969

By Irving Cadoff, Kurt Komarek, Edward Miller

THE lead-telluride phase diagram as compiled by ansen&apos; has one intermetallic compound, PbTe, with solid-solubility limits extending from 22 to 45 wt pct Te (31.4 to 57.1 at. pct). Pelzel2 redetermined the solubility limits on the lead-rich side of the compound by measuring the relative areas of the two phases in samples annealed in the liquid + compound region, and obtained data that agreed with that of Hansen. Recent studies of the semiconducting properties of PbTe3 however, have indicated that addition of either lead or tellurium to PbTe does not produce samples having carrier concentrations greater than about 10 19 cm-3. Assuming that each impurity atom results in one ionized charge carrier, this carrier concentration corresponds to a solubility range of less than 0.04 at. pct. Fritts and Karrar4 have also observed two phases in samples containing from 0.15 to 3.0 pct excess Pb. To resolve the discrepancy between these data, the solid solubility limits of the compound PbTe were reinvestigated, using several other techniques. Ten 25-g samples with compositions of 1/2, 1, 3, 5, and 10 wt pct excess Pb and Te and two 100-g samples of 15 and 65 wt pct Te were prepared, sealed in evacuated quartz capsules, and melted at 950oC. The 1 pct excess Pb and Te and the 15 and 65 wt pct Te alloys were homogenized for 96 hr at 450°C; the remaining specimens were annealed 50°C below the solidus temperature reported in Hansen. The specimens were polished and etched with dilute HNO,. All the samples were two phase, the second phase appearing at grain boundaries or as spheroidized inclusions in the grains. In the case of the tellurium rich specimens, the second phase could be identified as a eutectic. Debye-Scherrer powder diffraction patterns of the i, 1, 3, 5, and 10 pct excess samples were obtained using CuKa filtered radiation. The films were indexed as the B1 or NaCl structure. The calculated lattice parameter of PbTe was the same for all the specimens, with an average of a0 = 6.460 ± 0.0005A. Lines due to excess lead or tellurium were very faint but could be clearly seen in all the films. The relative areas of the two phases in the 15 and 65 wt pct Te samples were corrected for the differences in density of Pb, Te, and PbTe, and taken as proportional to the relative volumes of the two phases. The corrected relative volumes agreed with a phase diagram having negligible solubility of both lead and tellurium in lead tellurium. The density of the two specimens was obtained to give a third independent determination of the phase limits. The specimens were broken into small pieces to eliminate any internal porosity, and adherent air bubbles were removed by vigorous shaking under water for several hours. The density of lead (11.34 g per cm3) and of tellurium (6.25 g per cm3) was taken from the International Critical Tables and that of stoichiometric PbTe (8.25 g per cm3) calculated from the lattice parameter. For the 15 wt pct Te samples, the density assuming no solubility was calculated to be 9.89 g per cm3; the observed density was 9.86 g per cm8. For the 65 wt pct Te alloy, the density calculated for the case of no solubility was 7.24 g per cm3; the measured density wag 7.22 g per cm3. These results are consistent with those of planimetry and X-ray. SUMMARY Data have been presented which show that the solid solubility of both lead and tellurium in PbTe is

Jan 1, 1961

By M. T. Simnad, C. E. Birchenall, M. H. Davies

THE marker movements observed by Davies, Simnad, and Birchenall during the growth of magnetite on wustite have been misinterpreted. It is the purpose of this note to correct the original interpretation. In that investigation wustite specimens were prepared by oxidizing pure iron disks in water vapor until the iron was consumed. Argon was used as a carrier gas for the water vapor and on the complete conversion of the metal to its oxides (&apos;FeO&apos; plus a small amount (10 pct) of surface Fe3O) the water supply was bypassed and the specimens were annealed in argon alone in order to equilibrate the wustite with the overlying magnetite. After cooling, the magnetite was ground off, a crude magnetic test being employed to determine its complete removal. Radioactive silver streaks were then applied to the surface and the specimen was oxidized completely in water vapor to prevent hematite formation. After complete oxidation the markers were found to enclose about 80 pct of the magnetite with the other 20 pct lying outside the markers. This observation was interpreted to mean that oxygen transport was four times as great as iron transport during the growth of the magnetite. The conclusion would have been correct if, as in the case of wustite growing on iron, all the iron had started from one side of the marker and all the oxygen from the other side initially. Actually a material balance is required. For simplicity, take wustite to be exactly FeO, and magnetite to be Fe3O,. Then at the start of the reaction 3 FeO + O -> Fe,O., All of the iron and three-fourths of the oxygen of the final product will be within the marker inter- faces. The other fourth of the oxygen is in the gas phase outside the marker. From the experimentally determined final position of the markers simple calculation shows that one-fifth of the total iron has crossed the marker interface, while one-twentieth of the total oxygen has crossed in the reverse direction. The simplified result favors iron transport in the ratio four to one. However wiistite is not stoichiometric FeO. At 900°C, the temperature of the measurement, the composition is about FeO When the material balance for the same experimental result is repeated, assuming the product will be 1 mol of Fe3O4, it is found that 0.6 gram atoms of iron and 0.19 gram atoms of oxygen must have passed the marker in the same direction. (This is readily apparent from the reaction to form 1 mol of Fe3O4 SFeO The total oxygen supplied from the atmosphere is 0.61 gram atoms, but the iron which passes the marker interface, i.e., 0.6 gram atoms, requires 0.8 gram atoms of oxygen to convert it to Fe,O,.) If all the transport during magnetite growth is due to iron ion diffusion, then the marker would enclose about 85 pct of the final magnetite and the original measurement is in error by about 5 pct. This error is probably less than the uncertainty in locating the markers by autoradiography. The possibility also exists that the starting wustite was not quite saturated with oxygen and underwent further enrichment with consequent envelopment of the marker before magnetite caught up with the marker interface. In any case it appears that these measurements actually favor iron ion diffusion in magnetite overwhelmingly as the factor controlling its growth, although further experimental measurements are needed to eliminate the error in material balance described. Such studies are planned.

Jan 1, 1954

By P. T. Carter, A. B. Murad, H. B. Bell

The distribution of manganese and oxygen between molten iron and FeO-MnO-SiO2 slags not saturated with SiO2 has been determined and used to calculate activities of MnO and SiO2 in MnO-SiO2 slags. These were found to be intermediate between the corresponding activities in FeO-SiO2 and CaO-SiO2 slags. THE equilibrium constant for the reaction between molten iron containing manganese and slags containing FeO and MnO, namely: FeO(slag) + Mn = MnO (slag) + Fe(1iquid) is most conveniently represented by: (MnO) Kmn== (FeOHMn] [Fe] is omitted, since for dilute solutions of manganese in iron, afe is approximately constant. When activities are used for (MnO), (FeO) and [Mn], Kmn is a true equilibrium constant and will apply to all types of slags, but when weight percentages are used, the values obtained for Kmn for different slags vary considerably. The equilibrium between iron containing manganese and relatively pure FeO-MnO slags has been investigated by several workers;1-4 the most recent investigation reported is that of Chipman, Gero, and Winkler.4 Their results, corresponding to slags containing up to 4 pct SiO2, were represented by the equation: 6440 log KMn = +2.95 In this case both slag and metal may be assumed to be ideal solutions, therefore the values of Kmn so derived represent the true constant for the manganese reaction. As the molecular weights of MnO and FeO are almost equal, weight concentration of these oxides may also be used in the above expression. Acidic oxides such as SiO2 and P2O5 affect the activities of FeO and MnO differently, so that when total concentrations by weight of FeO and MnO are used in the above expression for Kmn the values obtained are no longer constant. These will be denoted by K&apos;mn. Körber and Oelsen5 investigated the manganese reaction using silica-saturated iron-manganese-silicate slags and found: 7940 logK&apos;mn =3.172 This corresponds to Kmn values much higher than those obtained for pure oxide slags. The results of Körber and Oelsen, and Chipman, Gero, and Winkler are summarized in Table I. In the present investigation it was decided to study the manganese reaction using iron-manganese-silicate slags not saturated with silica, and which fell mainly between the orthosilicate join 2FeO . SiO2 - 2MnO.SiO2 and the FeO-MnO side of the ternary system FeO-MnO-SiO2. It has been shown" that the phases present in solidified slags of this part of the diagram are (FeO, MnO) and (2Fe0.Si02, 2Mn0-SiO,) solid solutions. Such an investigation would be of interest in deoxidation and also gives information on activities in liquid slags. This equilibrium has not as yet been investigated successfully. Hilty and Crafts7 attempted to examine this reaction in a rotating crucible furnace, but were unable to obtain suitable slag samples. In the present investigation one series of experiments was carried out in a rotating crucible furnace, because the success of Taylor and Chipman8 with such a furnace in their study of oxygen distribution between molten iron and (CaO, MgO) — FeO-Si0, slags suggested that it would minimize contamination of the slag by the crucible material. A second series was carried out using a wire-wound resistance furnace. Rotating Crucible Furnace Experiments In all cases the metallic charge consisted of 800 to 1000 g Armco iron containing 0.02 pct C, 0.03 pct Mn, and traces of Si. Manganese and silicon additions consisted of electrolytic manganese (99.9 pct)

Jan 1, 1953

By D. L. Martin

THAT small amounts of impurities have a harm-J- ful effect on the malleability of metals and alloys is well-known. One common type of em-brittlement involves the formation of a small quantity of eutectic at the grain boundaries, and is typified by sulfur embrittlement of nickel. Another example of eutectic embrittlement—sulfur embrittlement of cobalt—is described in this report. In the preparation of specimens for a study of Co-Pt alloys, it was observed that the hot swagabil-ity of the alloys appeared to be influenced by the grade of cobalt used as melting stock. The cause of the hot-shortness was not traced to any particular impurity, although sulfur was suspected.&apos; The damaging action of sulfur on the malleability of cobalt has not been generally recognized,&apos;; in spite of the fact that the Co-S phase diagram8 eveals the same basic conditions—low solubility and eutectic formation—responsible for sulfur embrittlement of iron and nickel.7, 8 Apparently sulfur embrittlement has not been a serious problem in the fabrication of cobalt alloys. One related factor is likely the limited commercial experience with high cobalt alloys, since the predominant use of cobalt has been in alloys containing less than 75 pet Co. A series of Co-S alloys was prepared and studied to establish the effect of sulfur on the hot working characteristics of cobalt. Specimens, 5/8 in. diam by 4 in. long, were prepared by vacuum melting in magnesium oxide crucibles and casting in a copper mold. Two grades of low sulfur electrolytic cobalt were used as the basic material for the study, one from Johnson, Matthey and Co. and the other from the International Nickel Co. Each contained about 99.5 pet Co and had a nominal sulfur content under 0.005 pet. The sulfur was added initially as cobalt sulfide powder. Later, some low sulfur alloys were prepared by diluting the high sulfur alloys with cobalt. Trouble was experienced in controlling the sulfur content. Apparently much of the cobalt sulfide powder was lost during melting, as most of the samples contained a lower sulfur content than was added. The alloys were evaluated for hot brittleness by heating to 1000°C in a hydrogen furnace and swaging in air. The results of these tests are summarized in Table I. All the alloys containing less than 0.008 pet S were successfully hot swaged to 1/4 in. diam. The bars containing more than 0.015 pet S could not be swaged because of the formation of intercrystal-line cracks similar to those illustrated in Fig. 1. Examination of the microstructure of the cast bars revealed cobalt sulfide eutectic at the grain boundaries, Fig. 2. The sulfide was not always continuous at grain boundaries in bars that were hot embrittled but, in general, the particles did form a network that could account for the brittleness above the eutectic temperature, 880°C. There is no question about the brittle nature of a specimen exhibiting a continuous sulfide network such as is shown in Fig. 2b, though a sulfide distribution similar to that in Fig. 2a is marginal. This particular bar cracked when hot-swaged. However, other bars with lower sulfur content but with some sulfide phase at grain boundaries were successfully worked. The reduction of area of a hot tensile test specimen was also found to be a sensitive indicator of sulfur embrittlement. The variation of reduction of area with sulfur content is shown in Fig. 3 for specimens fractured at 900°C in an evacuated capsule. The ductility of cobalt is greatly reduced when the sulfur content exceeds 0.005 pet. Similar results were obtained for alloys tested at 800°C, below the eutectic temperature. The upper sulfur embrittlement limit of 0.015 pet, Table I, agrees with the observation of Kalmus8 hat

Jan 1, 1957

By E. I. Salkovitz, F. W. von Batchelder

DURING the last few years several papers1-&apos; have been published in which internal friction measurements have been used to determine the quantity of carbon or nitrogen dissolved in a iron. This method is based on the fact that, in pure Fe-N and Fe-C alloys, nitrogen and carbon cause peaks in the internal friction vs. temperature curve; at a frequency of 1 cycle per sec (cps) these peaks appear at $-200 and +360C, respectively, and if internal friction is expressed as Q-1, which is equal to times the logarithmic decrement, this figure will, by coincidence, give the weight percentage of nitrogen or carbon in solid solution.&apos; In most of the studies published, very pure iron (Puron) was used. In one case the influence of manganese on the behavior of nitrogen in a iron was mentioned.4 It would be of great value, especially for the study of aging and related phenomena, if this method could be applied to commercial mild steel with norrnal percentages of manganese, phosphorus, sulphur, etc. As a rule, in such steels carbon and nitrogen are present together, and the amounts of these elements in solid solution should preferably be determined separately. The fact that their internal friction peaks appear at different temperatures (+36° and + 20°C in pure iron) seems promising for such a selective determination. It is necessary, however, that the peaks are narrow enough not to interfere with one another, and further, that there is no effect from carbon on the behavior of nitrogen in stress induced diffusion, and vice versa. According to Fast,&apos; however, in the presence of manganese the nitrogen peak gets wider and appears at a higher temperature nearer the carbon peak, and thus the prospects for selective determination are reduced. (The carbon peak was not affected by the presence of manganese.) But even if fully quantitative de- terminations of the two elements are not attained, some relative figures on the sum of them and an indication of which one is the predominant one, would be of value. Some results from experiments along these lines will be reported here. An internal friction measuring device was assembled mainly following a description by KG." The measurements were also carried out as reported in that paper. Table I gives the chemical compositions of the four different materials used in this investigation. All materials were drawn to wires with diameter about 0.8 mm, and the analyses refer to these final shapes. Determination of Nitrogen Peak Wires from steels A, B, and C were decarburized in wet hydrogen (about 30 pct H2O) at 700°C until no carbon or nitrogen could be found by chemical analysis. No peak was then found in the internal friction. The wires were further annealed at 580°C for 16 hr in hydrogen bubbled through a solution of 6.8 pct NH3 in distilled water. Chemical analyses gave 0.04 pct N in A and C, and 0.06 pct in B. After annealing at 580°C for 15 min in a lead bath and water quenching, the internal friction was immediately measured. The resulting curves are shown in Fig. 1. At these high values of the internal friction the accuracy is comparatively poor; at Q-1 - 0.030 it is estimated to be 0.002. In order to make possible a calculation of the activation energy for diffusion of nitrogen, measurements were made at two different frequencies. Steel A shows rather broad peaks, and their temperatures can hardly be expected to be very accurate. Steels B and especially C are better in this respect. The finding of Fast&apos; that manganese broadens the nitrogen peak is con-

Jan 1, 1953

By S. W. Kennedy, M. Cohen, L. D. Calvert

A high-temperature X-ray diffraction method has been used to study the composition and the kinetics of formation of oxide scales at 800 °C on iron and pure iron-nickel alloys containing 25.6, 75, and 84 pct Ni. This technique has been combined with chemical analysis, and metallographic examination, and determination of weight-gain time curves. The 75 and 84 pct Ni alloys form a three-layer scale consisting of porous NiO next to the metal, a spinel layer, and a -Fe203 on the outside. The 25 pct Ni alloy produces a scale of spinel and Fe,O,, in which, however, traces of FeO and NiO are observed near to the metal. On all the nickel alloys the Fe20, is orieqted with the (107) plane parallel to the surfaces. The exposed surface of the Fe20, is in the form of needles whose axis is perpendicular to the specimen surface. Although the alloys show nonuniform oxidation rates as determined from weight-gain measurements, the X-ray data indicate that the total scale and individml scale layers grow uniformly and parabolically. Deep subscale formation is observed in the 25 pct Ni alloy only. This appeared to be associated with cracking of the scale and penetration of the oxygen along the grain boundaries. ALTHOUGH film formation has been investigated by high-temperature electron-diffraction techniques, for example by Gulbransenl and Hickman,&apos; there have apparently been no investigations of scaling by methods permitting study of the scale during formation at the reaction temperature. Methods involving quenching of scales are based on the working assumption that no significant changes take place on cooling. In general, however, compounds may disproportionate, and the different thermal expansions of constituents may cause disruption of the scale on cooling. In particular, some scales cannot be quenched without spalling. These difficulties are avoided by X-ray diffraction examination at the temperature of formation. High-temperature diffraction procedures also provide a method of determining the kinetics of formation of each phase separately in a multicom-ponent scale. The scaling of binary iron-nickel alloys Containing up to 30 pct Ni at a temperature of 800°C has been studied by Benard and Moreau using cooled specimen~,~ whilst Foley, Druck, and Fryxel14 made an electron-diffraction study of cooled oxide films formed on an iron 42 pci Ni alloy. In the present work the scaling of three iron-nickel alloys containing 25.6, 75, and 84 pct by weight of nickel, at 800°C in oxygen at atmospheric pressure was investigated by X-ray diffraction techniques using a Norelco Geiger-counter diffrac-tometer. The oxidation of iron was investigated for comparison. In addition normal metallographic examinations and chemical and X-ray analyses were made, and weight-gain time curves obtained. EXPERIMENTAL Materials Used—The analyses of the alloys were as follows: Percent by Weight Nickel 25.6 pct 75.4 pct 83.2 pct Aluminum 0.004 None found 0.002 Cobalt — 0.05 0.05 Chromium — — — Silicon — 0.01 None found Carbon All less than 0.05 pct The chemical analysis of the iron was: Al— 0.002 i 0.001 pct, C—0.007 pct, Cr less than 0.001 pct, Cu—0.002 ± 0.001 pct, Mn—0.003 ± 0.001 pct, N—0.0002 pct, 0-0.013 pct, P—less than 0.0002 pct, Pb—not detected, S—0.0017 pct, Si—0.0095 pct, Sn—none detected. This iron was the same as that used to make the alloys and was obtained from the same source-Vacuum Metals Corp. One specimen of pure iron from The British Iron and Steel Research Association was used for preliminary investigation. Specimens were machined to shape from cast rod, polished (the final polish being with 600 Sic paper), degreased in trichlorethylene, washed, and etched. The etching and neutralizing procedure adopted by

Jan 1, 1960

By Paul A. Farrar, Harold Margolin

The system Ti-Cr has been re investigated From 40 to 100 pct Cr. The high-temperature modification of TiCr, was found to exist in the temperature range from 1365 where it terminates in the eutectoid reaction TiCr,(TI)* — HE chromium-rich region of the Ti-Cr system was investigated by Vogel and Wenderott,&apos; Mc Quillan,&apos; Van Thyne et dl.,&apos; and Cuff Duwez and Taylor determined the crystal structure of the low-temeperature modification of TiCr, to be fcc a = 6.943A and Levinger&apos; discovered the existence of a second (high-temperature) modification of TiCr, and determited its crystal structure to be hexagonal a = 4.932A, c/a = 1.617i. No information was obtained as to the temperature range over which each modification of TiCr? existed; therefore the present investigation was initiated. I) Experimental Techniques Alloys employed for the delination of this system were prepared from iodide titanium and high-purity chromium. The purity of these materials is as follows: Iodide titanium: purity 99.99 pct; major impurities—carbon 0.0001 pct; oxygen 0 to 0.002 pct; nitrogen 0 to 0.002 pct; silicon 0 to 0.005 pct; manganese 0.001 pct; copper 0.001 pct (Foote Mineral Co., Lot 609-29). Chromium #1: metallic purity 99.997 min.; interstitial content—oxygen 0.27 to 0.46 pct; hydrogen 0.028 to 0.038 pct; nitrogen 0.0002 pct (Ave-quipo Inc.). Chromium #2: purity 99.9 pct; major impurities—carbon 0.01 pct; oxygen 0.013 pct; nitrogen 0.02 pct; silicon 0.01 pct; sulfur 0.03 pct; iron 0.01 pct (Fulmer Research Institute Ltd.). A total of sixteen alloys of thirteen different compositions was prepared in the range from 40 to 95&apos; *All percentages are given in weight percent. pct Cr. The compositions of the alloys prepared were as follows: Ti-40, 45, 50, 60, 62, 64, 66, 68, 70, 80, 85, 90, and 95 pct Cr. Two buttons were prepared of the 66, 90, and 95 pct Cr alloys. The 40 pct Cr and one of the 66 pct Cr alloys were prepared from the chromium # 2. All the other alloys were prepared from chromium #1. The alloys were arc-melted as 25-g buttons in a copper-hearth glass-walled furnace7 under an inert atmosphere of high-purity helium. The alloys were sintered at 250 amp and melted twice at 350 amp for 30 sec with the buttons being turned over between melts. Weight losses during melting were determined and in the range 45 to 68 pct Cr they were found, in all cases, to be less than 1.25 pct of the total alloy weight. A number of the high-chromium alloys shattered during cooling from either the first or second melt, which made the weight loss considerably larger than usual. The 70 and 80 pct alloys lost approximately 5.7 pct of their total weight, the 85 pct alloys 1.5 pct, the 90 pct alloy 2 pct, and the 95 pct alloy 3 pct. However, it is felt that the actual composition of the alloys in this region is probably within approximately 1 pct of the intended composition, as a large portion of the material lost was that due to shattering after melting. Nominal compositions were therefore used in plotting data and referring to the alloys. The alloys were cut into specimens, wrapped in molybdenum sheet, and encapsuled in argon-filled quartz or Vycor tubes for heat treatment. The heat-treatment times and temperatures are given in Table I. The specimens were quenched in iced brine (I.B.Q.) following heat treatment. The standard techniques of grinding, polishing., and etching were used in preparing the specimens for metallo-graphic examination. For alloys below 68 pct Cr

Jan 1, 1963

By R. P. Rothwell

A Reference to the geological map of Alabama shows the Goalmeasures of that State to form three distinct fields. The Coosu, or most easterly, contains about one hundred square miles ; the Cahaba, or middle field, which is also the most southern true coal in the United States, contains about 230 square miles ; and the Warrior field, which contains in the State of Alabama some 5000 square miles, is the southern extremity of the great carboniferous deposit, which extends through Pennsylvania, West Virginia, Kentucky, Tennessee, and Georgia. But very little has yet been done towards developing those coalfields, partly owing to the absence of all commercial manufacturing enterprise in the South under slavery, and partly owing to the want of capital and the disturbed condition of the South since the war. During the past three or four years I have devoted a large part of my time to the examination of the coal and iron ores of this range,

By W. C. Dickerman, J. F. Thornton

TOTAL global war is making extraordinary demands on the oil industry. Huge quantities of 100-octane gasoline, extreme service lubes, toluene and other miscellaneous products are required. 100-octane gasoline is blended from isopentane, base stock, and alkylate. Isopentane is fractionated from natural or refinery gasoline; but since only limited quantities of base stock can be made in this way, catalytic cracking is rapidly becoming the major source of base stock. Alkylate, the most important component, is synthesized from isobutane and an olefin. Extraordinary demands are forcing the full utilization of all present sources and the development of new supplies of feed stocks. Fortunately, the United States finds itself with well-developed processes already available, and this is true of the manufacture of lubricating oil as well. Toluene is now being produced by new methods from special cuts fractionated from selected crudes or from catalytically processed naphthas. Designers of refinery equipment are modifying past practices to conserve every bit of material possible.

Jan 1, 1942

By T. H. Janes

NATURAL abrasives of some type are found in all countries of the world. In order of their hardness the principal natural abrasives are diamond, corundum, emery, and garnet, which are termed high grade, and the various forms of silica, including pumice, pumicite, ground feldspar, china clay and, most important, sandstone. The properties qualifying materials for use as abrasives are hardness, toughness, grain shape and size, character of fracture, and purity or uniformity. For manufacture of bonded grain abrasives such as grinding wheels, the stability of the abrasive and its bonding characteristics are also important. No single property is paramount for all uses. Extreme hardness and toughness are needed for some applications, as in diamonds for drill bits, while for other purposes the capacity of the abrasive to break down slowly under use and to develop fresh cutting edges is of greatest importance, as with garnet for sandpaper. In dentifrices, soaps, and metal polishes, of course, hardness and toughness are objectionable.

Jan 10, 1954