Search Documents

By D. H. Baldwin, R. E. Reed-Hill

Six compositions of polycrystalline ZY-0 alloys, containing up to 4.2 at. pct 0, were tested in tension between 77° and 600° K. The data obtained from each of the compositions corresponded closely to a rela-ion between yield stress and absolute temperature of the form In s/so = BT, where oo is the yield stress extrapolated to zero degrees and B is a constant. In agreement with others who have observed this relationship, it is shown that the activation energy may be expressed as Ho In so/s. In the present specimens Ho is approximately 18,000 cal per mole and is apparently independent of temperature and composition inside the limits of the investigation. It is also demonstrated that this form of activation energy cowesponds to a strain rate sensitivity parameter RT/Ho. Oxygen was also noted to have an effect upon the operative deformation mechanisms. With increasing oxygen concentration there was an increased tendency to observe both nonbasal slip and cross-slip phenomena. Oxygen does not seriously inhibit twinning more than it does slip. Twins were observed in all specimens tested. It is becoming increasingly evident that interstitial atoms in solid solution are able to interact strongly with mobile dislocations. Stein, Low, and seybolt,&apos; have shown that, if the carbon concentration in bcc iron is lowered below the solubility limit, its flow stress temperature dependence is markedly reduced. This suggests that carbon atoms in interstitial solid solution may be responsible for the pronounced temperature dependence of the flow stress normally observed in iron. This view has recently been challenged by Leslie and sober2 who observed a strong flow stress temperature dependence in iron to which a trace of titanium had been added in order to remove carbon atoms from solution. Since the interstitial concentration must be reduced below approximately 1 ppm in order to produce a pronounced effect on the flow stress temperature dependence,&apos; studies of the effect of interstitials on the flow stress in iron necessarily involve serious experimental difficulties in alloy preparation. There are other metals, however, in which strong effects of interstitial solutes upon both the flow stress and its temperature dependence are observed. Of particular significance is zirconium which, according to Domagala and Mcpherson, 3 is capable of dissolving 28.6 at. pct O. The O-Zr alloy system is an almost ideal system for studying the interaction of interstitial atoms with deformation modes since it is possible to form alloys capable of study over an extensive range of compositions. Mills has made such a study using single crystals oriented primarily for single prismatic slip4 and has found an effect of oxygen concentration on the flow stress temperature dependence analogous to that observed in iron due to carbon by Stein, Low, and Seybolt. The present paper is specifically concerned with the effect of oxygen on deformation in polycrystalline zirconium. Although plastic flow in this type of specimen is much more complex than that reported for the single-crystal work, and involves both slip (on several different types of planes) and mechanical twinning, the results of this investigation are in general agreement with the single-crystal observations concerning the effect of oxygen on the temperature dependence of the flow stress. In addition, they also demonstrate that oxygen affects the acting deformation systems. This is in contrast to single-crystal results4 that showed only single slip on a prism plane. EXPERIMENTAL PROCEDURE Material. High-purity hot-rolled zirconium strip, 0.2 in. thick by 4 in. wide, of 0.10-mm average grain diameter, was used for forming alloys. It was obtained from the Carborundum Metals Co., Akron, N.Y., whose analysis indicated the major impurities were, in wt ppm: Hf, 540, C, 145; Fe, 100; and 0, <80. The plate texture was similar to a wire texture, with basal planes generally parallel to the rolling direction and basal poles randomly distributed about the rolling direction. The heat treatments described below did not appreciably alter the basic texture. specimen Preparation. Small threaded-end tensile specimens were machined from the plate with axes perpendicular to the rolling direction. These transverse specimens had gage sections 1 in. long by 0.060 in. in diam. The small gage section diameter was dictated by the fact that the alloys were formed by dif-

Jan 1, 1969

By P. E. Busby, C. Wells, M. E. Warga

Fundamental data on the rate of diffusion of boron in austenite and solubility of boron in the a and y phases of iron and steel have been obtained from deboronizing experiments and provide partial explanations for some of the phenomena observed in boron steels. The rate of diffusion of boron is about the same as carbon in austenite. The solubility of boron in austenite at normal heat-treating temperatures is less than 0.001 pct. A partial tentative Fe-B phase diagram in the important low boron concentration ranges and an equation representing the diffusion of boron in austenite are presented. A LTHOUGH a search of the literature revealed ALTHOUGHthat boron diffusion had not been studied quantitatively and systematically prior to 1948, a few qualitative observations which were made by following the diffusion of boron into iron packed in ferro-boron1-3 suggest that boron obeys normal diffusion laws and that the rate of diffusion increases with increasing temperature. The claim of Cornelius and Bollenrath1 that boron does not appear to influence the rate of carbon diffusion has recently been substantiated by Wells, Batz, and Mehl.4 Calculations based on data from the paper by Campbell and Fayv indicated that the diffusion coefficient (D) for boron in iron at 900°C is approximately 3x10 sq cm per sec; a value of 2x10-7 sq cm per sec at 1038°C has been reported by Digges et al in connection with decarburizing experiments on a commercial boron steel containing 0.43 pct C. During the period 1948 to 1950 several diffusivity constant (D) values for the diffusion of boron in the y phase of iron and steel and a number of solubility values for boron in both a and y phases were reported. It was concluded tentatively as a result of Metals Research Laboratory studies that D values for boron in y and a phases are about the same as for carbon in the comparable phasesa and that carbon up to 0.4 pct did not affect the rate of diffusion of boron in y iron above 1000°C within the limits of experimental error. Whether saturation of the y or a phases with carbon would significantly affect rates of diffusion of boron through them was then and still remains in doubt. The best estimate of Q (activation energy) was reported to be about 25,000 cal, somewhat lower than that for carbon in y iron. The solubility of boron in y iron at 1000°C was thought to be higher than 0.004 pct B but not as high as a more recent analysis of available data shows it to be. The solubility of boron in a iron at 700°C was reported to be 0.0004 pct B, but it would not have surprised the authors if the true solubility value is actually lower than this. Breaks in diffusion curves which were not understood when first obtained prior to 1950 have now been recognized as indicating solubility limits, and these are included in the present paper. Experimental Procedure Two methods were employed in an effort to determine diffusion coefficients (D) for boron in austenite. Early experiments involved the use of welded couples prepared in accordance with the procedure of Wells and Mehl,&apos; but when the results of these experiments proved to be unsatisfactory for calculating D values, studies were continued by means of deboronizing experiments. In both cases, boron analyses following the diffusion anneal were carried out spectrographically and all D values were computed using the Grube solution of Fick&apos;s law. The precision of the spectrographic method used proved to be about equal to that reported by Corliss and Scribner" —average deviation from the mean about 5 pct of the amount present when the boron content is 0.003 pct. Concentration-penetration curves obtained from spectrographic analyses of welded couples generally indicated that practically no boron was transported across the weld interface during the diffusion anneal. Furthermore the concentration-penetration

Jan 1, 1954

By A. G. Weber, K. H. Coats, M. H. Terhune, R. L. Nielsen

Two computer-oriented techniques for simulating the three-dimensional flow behavior of two fluid phases in petroleum reservoirs were developed. Under the first technique the flow equations are solved to model three-dimensional flow in a reservoir. The second technique was developed for modeling flow in three-dimensional media that have sufficiently high permeability in the vertical direction so that vertical flow is not seriously restricted. Since this latter technique is a modified two-dimensional meal analysis, suitably structured three-dimensional reservoirs can be simulated at considerably lower computational expenses than is required using the three-dimensional analysis. A quantitative criterion is provided for determining when vertical communication is good enough to permit use of the modified two-dimensional areal analysis. The equations solved by both techniques treat both fluids as compressible, and, for gas-oil applications, provide for the evolution of dissolved gas. Accounted for are the effects of relative permeability, capillary pressure and gravity in addition to reservoir geomety and rock heterogeneity. Calculations are compared with laboratory waterflood data to indicate the validity of the analyses. Other results were calculated with both techniques which show the equivalence of the two solutions for reservoirs satisfying the vertical communication criterion. INTRODUCTION Obtaining the maximum profits from oil and gas reservoirs during all stages of depletion is the fundamental charge to the reservoir engineering profession. In recent years much quantitative assistance in evaluating field development programs has been provided by computerized techniques for predicting reservoir flow behavior. Because of the spatially distributed and dynamic nature of producing operations, automatic optimization procedures, such as those now in use for planning refining operations, are not now available for planning reservoir development. However, present mathematical simulation techniques do furnish powerful means for making case studies to help in planning primary recovery operations and in selecting and timing supplemental recovery operations. A number of methods have been reported which simulate the flow of one, two or three fluid phases within porous media of one or two effective spatial dimensions>-4 However, applying computer analyses to actual reservoirs have been limited mostly to two-dimensional areal or cross-sectional flow studies for two immiscible reservoir fluids. To obtain a three-dimensional picture of reservoir performance using such two-dimensional techniques, it has been necessary to interpret the calculations by combining somehow the results from essentially independent areal and cross-sectional studies. To the authors&apos; knowledge, the only other three-dimensional computational procedure, in addition to those presented here, was developed by Peaceman and Rachford8 to simulate the behavior of a laboratory waterflood. Two computational techniques which may be used to simulate three-dimensional flow of two fluid phases are described in this paper. The first method, called the "three-dimensional analysis", employs a fully three-dimensional mathematical model that treats simultaneously both the areal and cross-sectional aspects of reservoir flow. The second method, called the vertical equilibrium (VE) analysis", is applicable

By Joseph Kaye Wood

A metal is said to be overstrained when it is deformed beyond the elastic limit at a temperature well below the critical range, as in cold working. Quantitatively, overstrain might be considered as that part of the total elastic deformation of the piece of metal, left over after the external load is removed, that added to the permanent deformation due to plastic action will give the total permanent deformation. Ordinarily the effects of this phenomenon, which vary with the internal residual stress probably in accordance with Hooke&apos;s law, are more noticeable when the yield point of the metal is exceeded, but they probably also exist to a smaller degree when the load is just large enough to cause the least amount of permanent set. These effects, which we recognize as the result of overstrain, are as follows: 1. An apparent increase of the elastic limit in tension and a decrease of the elastic limit in compression, provided the external load is tensile. The reverse is true when the load is compressive. 2. An elastic after-effeet in which time and temperature are important factors. 3. A state of imperfect elasticity in which Hooke&apos;s straight line becomes slightly curved, giving rise to an hysteresis loop. 4. In addition to the apparent increase in the elastic limit, such properties as the hardness, ultimate strength, and resistance to fatigue failure are increased, provided the overstraining has not been carried far enough to make the metal brittle. 5. Correspondingly the ultimate elongation, reduction in area, magnetic quality, ratio of endurance limit (fatigue breaking stress) to elastic limit, and resistance to season cracking (in certain copper alloys) are decreased. The question naturally arises: how do these changes in the properties of a metal resulting from overstrain influence our method of design? The fact that most of the desirable qualities are increased makes overstraining a favorable process, from an engineering standpoint; but on the other hand, the loss of such qualities as perfect elasticity and complete

Jan 1, 1924

By C. W. Gennet

Announcement was made in the spring of 1926 that the Boston & Maine R. R. Co. had contracted with the well-known German steelmakers, Messrs. Fried Krupp, for the manufacture of 15,000 tons of basic open-hearth steel rails at the Rheinhausen Works, for delivery to Boston, Mass. The manufacture of rails in the United States has for many years been almost a national pride, and as this feeling is chiefly the result of a long-time liberal and consistent patronage of American rails by American railroads, it is not strange that this somewhat unusual announcement should arouse more than ordinary interest. Since the end of the World War, the importation of foreign rail has been fairly large, principally because the newly created economic conditions have rendered some American competition more difficult, but the tonnage imported, for the most part, has been made up of small orders for miscellaneous use; and the contract referred to constitutes the largest single importation of foreign rail in over ten years. In 1915, the Algoma Steel Co. of Sault Ste. Marie, Canada, supplied the Illinois Central R. R. with 30,000 tons of rails,&apos; and various other American roads with smaller amounts. In 1902, 1903 and 1904, large tonnages of rail from abroad were purchased, the Louisville & Nashville R. R. alone obtaining 30,000 tons from German mills. It is the object of this paper to present, in what is believed to be a new and concise form, figures showing the production and consumption of rails in the United States, and to record some of the testing and inspection results of the recent Krupp rails; also, to direct attention to two quite unique departures from American practice that were regular features of the Krupp process and which are worthy, it is thought, of careful study. Production and Consumption of Rails in the United States Table 1 shows the tonnage of rail produced in the United States and the amount imported, exported, and consumed by years since 1849. That, evidently, was the first year of record, for the statistics of the American Iron and Steel Institute and its predecessor, the American Iron and

By W. R. Hibbard

The increased strength of a polycrystal-line metallic aggregate compared with that of its individual crystals generally has been associated with complex stress distributions at the grain boundaries resulting from atomic irregularity between grains. This disregistry, together with the necessity for adjacent crystals to deform compatibly regardless of the single crystal crystallo-graphic strain mechanism, complicates this mechanism so as to increase the metal&apos;s resistance to deformation. Although Taylor1 has shown from purely mechanical considerations the requirement for at least five active slip systems to absorb the complexities during the homogeneous deformation of polycrystalline face-centered cubic metals, experimental studies by Barrett and Levenson2 indicate that this is feasible only in a qualitative sense because of deviations from homogeneous deformation. Seitz and Read in their review3 state: " Unfortunately . . . present knowledge of the grain boundary influence is not sufficient to complement the work in single crystals and provide us with a good foundation for treating polycrystals." The purpose of this investigation was to attempt to clarify the gap between single crystals and crystalline aggregates by an analysis of the effects of dcformational stresses. Some of the results were described by C. H. Mathewson in his 1943 Campbell Memorial Lecture.zl Previous Investigations Since the performance of single crystals deformed under pure stresses has been relatively thoroughly investigated, the most significant researches are concerned primarily with deviations from single crystal behavior of large grained specimens. Qualitative grain boundary effects involving the observed amount of slip werc reported by Carpenter and Elam5 in 1921. Individual crystals in a two or three grained aluminum specimen deformed by tension acted in the normal manner described by Taylor and Elarn4 except for marked modifications at the grain boundaries. There the power to withstand deformation was considerably increased, leaving a ridge on the specimen where decreased slip occurred, often noticeable yi in. from the boundary. Adcock,6 Yamaguchi,&apos; Seumel, Hirstg and others have also reported this phenomenon as a qualitative trend. Yet attempts by O&apos;Neill&apos;o and Ljunggrenll to measure a difference in hardness at grain boundaries in undeformed specimens were unsuccessful. Miller12 measured quantitatively the reduction in slip near the boundary between the single crystal and polycrystalline areas of zinc specimens. These effects consisted of two parts: I. Next to the polycrystalline interface thc distribution of stresses was so altered

Jan 1, 1949

By R. S. Shoemaker, F. W. McQuiston

BENGUET EXPLORATION, Inc. Tuba, Benguet, Philippines 1970 Operating Data ORE DESCRIPTION: Complex ore mostly sulfides and composed mainly of sphalerite and pyrite with minor amounts of chalcopyrite, galena, arsenopyrite, hematite, magnetite, chlorite, calcite, garnet and quartz. TYPE OF MINE: Underground, cut and fill method ORE HAULAGE TO MILL: Mine rail cars with electric locomotives. CAPACITY in TONS/24 HRS: 130 ASSAYS: Mill Heads Mill Tails Au = 0.65 oz per ton Au = 0.096 oz per ton Cu = 0.75% CU = 0.27 % Zn = 10.50 % Zn = 0.64 % Ag = 3.20 oz per ton Ag = 0.33 oz per ton Cd = 0.01 % PRODUCT: Au, Ag, Cu, Zn and Cd RECOVERIES: = 90% ~g = 89% Cu = 60% Zn = 94% SCREEN ANALYSIS OF MILL FEED: 90% -200 mesh POWER: Grinding 25.4 Kwh/T Copper Flotation 14.5 Zinc Flotation 13.3 Cyanidation 20.4 Others 25.0 TOTAL POWER: 98.6 KwH/T WATER: Pumped from riverside and underground 50 to 100 meters distance. Consumption of about 700 gallons per ton of new water.

Jan 1, 1975

By S. Leber, R. F. Hehemann

This investigation describes the kinetics of alloying in a (Cb-15 wt pct W. 5 wt pct Mo, 1 wt pct Zr) powder-metallurgy alloy. The degree of homogeneity obtained in hydrostatic ally pressed and vacuum-sintered samples is described by composition distributions resulting from analysis of X-ray dvfraction line profiles. Sintering variables and degvee of powder dispersion were evaluated. The utility of single-value parameters obtained from composition distributions is disaissed. The spatial distribution of composition, as revealed by anodically tinted metallographic sarrzples, was used to provide diffision models based on a concentric-sphere geometry. Diffusion equations developed from these models were found to be in general agreement with experimental results. The powder-metallurgy method for the production of refractory metal alloys has the ability to produce an inherently fine-grained, fabricable structure. The more general use of this method is inhibited, in part, by the presumed difficulty in obtaining homogeneity on a microscale. The degree of homogeneity therefore is an important, but usually neglected, variable in specifying the quality of a powder-metallurgy alloy. Convenient techniques for measuring the degree of homogeneity are now available,&apos; and have been used to develop a model describing the process of alloying in a simple binary mixture.&apos; In this investigation, the process of alloy formation has been studied in a more complex system. PROCEDURE The columbium-based F-48 mixture was prepared from the constituent powders shown in Table I. The particle sizes tabulated were provided by the vendors of the individual powders. Standard laboratory techniques utilizing a jar mill were employed for blending. The blended powders were hydro-pressed into 1-in. diam rods which were then sliced into thin discs for vacuum sintering. All samples were given a preliminary treatment at 1700°C for 2 hr. Varying degrees of homogeneity were obtained using additional treatments at higher temperatures. The degree of homogeneity obtained by a specific sintering treatment was evaluated metallographi-cally using the anodic-tinting technique described by olff,&apos; and quantitatively by the analysis of X-ray diffraction line profiles using the X-ray diffraction technique developed by udman.&apos; The diffraction technique is strictly valid only for binary systems. However, the relatively small difference between the lattice parameters of tungsten and molvbdenum when compared with columbium permitted the treatment of the complex composition of F-48 as a (W, Mo)-Cb pseudobinary. Calculations were weighted in accord with the W-Mo ratio in the F-48 composition. The contribution of the 1 pct Zr was ignored since it could not even be detected in the blended powder. Two factors are required to convert an X-ray line profile into a composition distribution. The variation of these factors with composition is shown in Fig. 1. Curve A was used to convert angular posi-

Jan 1, 1964

By E. C. W. Perryman

The recovery of X-ray line broadening, hardness, and electrical resistivity from cold worked AI-Mg alloys has been investigated. The results, together with those from density measurements, suggest that magnesium atoms freeze in the excess vacancies formed by cold working, and that this affects the climb of dislocations during the recovery process. PREVIOUS work1, " has shown that while 1 pct Mg increases the activation energy for recrystalliza-tion, it decreases the activation energy for the recovery of mechanical properties and decreases the subgrain size both after cold working and annealing. A similar result has been reported by Varley2 for an A1-2 pct Mg alloy. With plastic deformation at high temperatures, McLean and Farmer&apos; and Rachinger have found that magnesium appears to retard the motion of dislocations and, furthermore, they find little or no effect of magnesium on the size of subgrains formed during high temperature deformation. In view of the apparent contradictions as to the effect of magnesium on subgrain size, the recovery process in Al-Mg alloys has been investigated more thoroughly by studying the annealing out of X-ray line broadening, hardness, and electrical resistivity from alloys cold worked at room temperature. Material Used—The chemical analyses of the alloys are given in Table I. Fabrication—The material used was cold rolled 20 pct at room temperature, the grain size prior to the last cold rolling operation being similar to that used in previous work; i.e., 230. The experimental procedure for annealing, determination of X-rav half-veak breadth. hardness measurement, electEica1 resistivity, and density and metallographic examination was exactly the same as previously described." Variation of X-Ray Half-Peak Breadth with Annealing Time—Isothermal annealing curves at 100°, 200°, and 250°C were obtained for material cold worked 20 pct. The half-peak breadth of the (333) Ka, line directly after cold working is shown as a function of magnesium content in Fig. 1. Only with the 2.87 pct Mg alloy was overlapping of the a, and n.. reflections observed to any appreciable extent. To separate these, Rachinger&apos;s method&apos; was used. Typical isothermal annealing curves are shown in Figs. 2 and 3 for 100" and 200°C, respectively. These curves are similar to those obtained previously for super-purity aluminum except that the

Jan 1, 1957

By James J. Bean

F. M. Lewis—I believe that density recorders are a prerequisite to all well operated ore concentrators. Well designed density instruments are very accurate and give an excellent record of the steadiness of the operation. Controlling the density of a pulp with an instrument, as described by Mr. Bean, is new and the experiences in developing this controller at the American Cyanimid Co.&apos;s Mineral Dressing Laboratory are very interesting and should be extremely helpful to others who are planning on designing or installing controlling density instruments. Instruments for recording the density of the classifier overflow or flotation feed are rather common in ore concentrators, but there are a number of profitable uses for these instruments that are not too well known. Density recorders with bubble tubes submerged to different depth in a classifier pool give an excellent record of the classifier operation. The loading and unloading of the machine, that is so easily masked in the density of the overflow, can be easily recorded if the instrument is installed at some depth in the classifier pool. On some occasions, two instruments with bubble tubes at different depths give a more candid picture of the irregularities in the classifier operation. When cleaner machines are operated in closed circuit with roughers, a record of the density of the cleaner tails will indicate the circulating load in the circuit and is very helpful in coordinating different operators, because quite often the circulating load will be increasing for some time before the analyses of the products will change. Density recorders are used to record the variations in the dilution of the underflow from thickening tanks and in at least one plant the instrument controls the underflow.

Jan 1, 1951

By James J. Bean

F. M. Lewis—I believe that density recorders are a prerequisite to all well operated ore concentrators. Well designed density instruments are very accurate and give an excellent record of the steadiness of the operation. Controlling the density of a pulp with an instrument, as described by Mr. Bean, is new and the experiences in developing this controller at the American Cyanimid Co.&apos;s Mineral Dressing Laboratory are very interesting and should be extremely helpful to others who are planning on designing or installing controlling density instruments. Instruments for recording the density of the classifier overflow or flotation feed are rather common in ore concentrators, but there are a number of profitable uses for these instruments that are not too well known. Density recorders with bubble tubes submerged to different depth in a classifier pool give an excellent record of the classifier operation. The loading and unloading of the machine, that is so easily masked in the density of the overflow, can be easily recorded if the instrument is installed at some depth in the classifier pool. On some occasions, two instruments with bubble tubes at different depths give a more candid picture of the irregularities in the classifier operation. When cleaner machines are operated in closed circuit with roughers, a record of the density of the cleaner tails will indicate the circulating load in the circuit and is very helpful in coordinating different operators, because quite often the circulating load will be increasing for some time before the analyses of the products will change. Density recorders are used to record the variations in the dilution of the underflow from thickening tanks and in at least one plant the instrument controls the underflow.

Jan 1, 1951

By J. H. Henderson, H. J. Ledbetter, N. B. Gove, J. D. Griffith

INTRODUCTION The results of a series of laboratory flood tests using liquid Iso-butane to displace refined oils from test cores are pre- ented and interpreted on an empirical bask. The study Revealed the similarity of the miscible liquid displacement to that of the immiscible-fluid displacement mechanism. The efficiency of the iso-butane flood decreased markedly as the oil Viscosity increased. but the effect of injection rate on the effectiveness of the primary production stage was negligible over the range investigated. The presence of free-gas saturation prior. to iso-butane breakthrough increased the volume of iso- Butane required to recover a given percentage of the oil present. Injection of liquid i.e.-butane prior to water follicle sculpted in a marked improvement in oil recovery by the water flood. INTRODUCTION The production of petroleum is often enhanced by the injec-1i1)n of extraneous fluids into the reservoir. It has been suggeited that the injection or cycling of a wet gas or a liquefied petroleum gas would he instrumental in increasing the effic.ienr!; of oil recover! to a greater degree than the commonly injected fluids. dry pas and water. Although instances of injection of light liquid hydrocarbons are not unknown, a systrmatic recording of the result is unavailable and superfi- cially, the practice gives the impression of being economicaIIy unsound. For specific types of displacement, analytic: solutions have been advanced which aid in understanding the physical mechanisms involved. However, there is no generalized theoretical concept which permits adequate prediction of displacement efficiency from a knowledge of readily measured reservoir rock and fluid properties. The Buckley-Leverett approach to oil displacement by an immiscible phase is an admirable analysiy of that type of mechanism. Dykstra and Parsons have introduced a useful concept in their evaluation of the role of the mobility ratio and its merit in rationalizing displacement phenomena. Everett, Gooch and Calhoun3 in their report on the effect of viscosity ratio and miscibility have pointed out the lack of a comprehensive theoretical approach and the desirability of investigating the mechanism of miscible-miscible displacement. In lieu of a well-developed theory concerning miscible-111isci1)le displacement and in view of the scarcity of engineering information on actual LPG injection trials, the limited program of laboratory experimentation described below was undertaken. OBJECTIVES The original broad objectives of the program, to study the oil recovery process using LPG as the displacing phase, defined the direction and scope of the laboratory tests. The specific objective. of the experimentation were to evaluate

Jan 1, 1953

By Hjalmar W. Johnson

IT has long been accepted that blast-furnace practice varies to some degree with the coke used. While the qualities desirable in iron have been known for some time, the qualities in coke that produce such iron have not been established. There are no objective standards for blast-furnace coke, which is usually described in general terms, as good or bad. Many experienced operators believe that coke cannot be measured objectively except by using it in the furnace, noting the result, and labeling the coke according to furnace operations. This is admittedly unscientific, and besides is useless for the two main purposes for which a measure of coke quality is needed: (I) to produce the best possible coke from the coals and equipment on hand; (2) to test new coals and determine their value for blast-furnace coke. In seeking such an objective measure, much work has been done on tumbler tests, shatter tests, sizes of coke, porosity, specific gravity, reactivity or combustibility and other tests, but as yet very little has been published in which conclusive correlations have been established between such objective measures and furnace operation. In our study of the problem during the past 8 years we have developed no new measures of coke quality, but we have collected data that are presented here in the hope that they may assist in further work, so that at some future time there may be developed such positive measures. The purpose of this paper is to show that there are variations in coke and that such variations do influence the operation of blast furnaces. At the same time we must remember that there are variations in blast-furnace operation and it may be the blast furnace that is at fault. This correlation of coke properties with blast-furnace operation will be worked out in the following steps: I. Discussion of a period when a change in the coke resulted in an increase in efficiency on one furnace and a decrease in efficiency on another. 2. Adaptation of the inefficient furnace to the available coke so that normal efficiency was restored. 3. The use of radial distribution: a discussion of the effect of size of ore layer in adapting blast-furnace operation to the coke. 4. An example of a change in size of coke and the detrimental influence on the production of one furnace. 5. An example of a change in size of coke, together with manufacturing data, to show why it changed, the conclusion being that coke is a product with an optimum value. 6. Illustration of the fact that coke has different optimum values on two furnaces, with discussion on adaptation of operation so the optimum values will be the same. 7. Limitations of the use of screen tests as an objective measure of coke quality. 8. Importance of uniformity in coke. FUNCTIONS OF COKE AND QUALITIES REQUIRED TO PERFORM THESE FUNCTIONS Coke has three important functions in a blast furnace: (I) to furnish most of the

Jan 1, 1941

By J. E. Steiner, J. M. Hodge, M. A. Orehoski

Ingots of four steels (1045, 1080, Ni-Mo-V, and Ni-Cr-Mo-V) were cast at pressures varying from about 1 to 760 mm of mercury, so as to obtain a range of hydrogen contents in each steel. The susceptibility of these steels to flaking was evaluated by cooling hot-rolled blooms at a range of cooling rates, varying from water quenching to slag cooling, and studying the occurrence of flaking as a function of cooling rate. The steels exhibited differences in susceptibility to flaking, and a tlzreshold value for hydrogen content for each steel was found, below which the susceptibility was very low and above which the susceptibility increased markedly with increasing hydrogen content. Mechanical property evaluations, metallogvaplzic exantinations, and X-my diffraction determinations o,t retained austenite were made on samples from the blooms. A mechanism of flaking which is consistent with the observed behaviors, the effects of hvdrogen content, and the differences in susceptibility among the steels investigated is postulated, based on the results of mechanical property evaluations and metallographic and X-ray diffraction studies. ThE important role of hydrogen as a factor in the occurrence of "flakes" or "hair-line cracks" in steel has now been established by many investigations. These have included investigations by steel producers and forging manufacturers, to whom the prevention of flaking is a very real and serious problem, and many research studies aimed primarily at establishing the mechanism of this behavior Several investigators3 have reported that steels cast at reduced pressures (absolute pressures of about 1 mm) not only are low in hydrogen content but are essentially insensitive to the formation of flakes. These investigations have shown that a general relationship exists between hydrogen content and susceptibility to flaking. The difficulty of obtaining suitable samples of steels of a given composition with the desired range of hydrogen contents, particularly in the relatively large sections in which flaking most commonly occurs, has been the principal obstacle to quantitative evaluations of these relationships. Steels with intermediate hydrogen contents between 1 ppm, and the 4ppm or higher of air-cast steels are generally not available in commercially produced steels. Laboratory procedures, in which the hydrogen is introduced into solid steel samples by heating in a hydrogen atmosphere under pressure, generally involve a limitation in the size of the sample which can be treated, and thus are not representative of the behaviors in large sections. The availability of a facility at the South Chicago Works of U.S. Steel, in which several ingots could be cast from a single heat of steel at total air pressures ranging from 0.25 to 760 mm of Hg, has made it possible to overcome this obstacle and to obtain ingots of a given steel covering the intermediate range of hydrogen contents desired. These ingots, furthermore, are of a size suitable for the production of product with section sizes large enough to be representative of the products in which flaking most commonly occurs in commercial production. In these experiments, this facility was used to study the relationships between hydrogen content and the susceptibility to flaking of four steels, two plain carbon steels at 0.45 and 0.80 pct C and two low-carbon alloy steels representing a medium and a rather high hardenability level. These flaking studies were supplemented by evaluations of mechanical properties and by metallographic studies on samples from the blooms, in order to obtain pertinent information on the factors other than hydrogen content which influence the susceptibilities of these steels to flaking. Based on the results of these tests, a mechanism for the initiation and propagation of the flaking cracks, which is consistent with the observed behaviors, is postulated. MATERIALS AND EXPERIMENTAL WORK Steelmaking and Conversion. To provide material for the investigation, five 29- by 35-in., hot-topped, big-end-up ingots were cast from each of four 80-ton, basic electric-furnace heats of four different steels (a 1045 steel, a 1080 steel, a Ni-Mo-V steel, and a Ni-Cr-Mo-V steel). A double-slag practice was used on all steels and the two plain carbon steels were Si-A1 deoxidized with an addition of 2 lb of A1 per ton, while the Ni-Mo-V and Ni-Cr-Mo-V steels were deoxidized only with silicon and

Jan 1, 1964

By R. M. Schuller, J. J. Suloway, W. F. Childers, R. A. Griffin, S. J. Russell

Seven solid wastes from coal conversion processes were characterized chemically and mineralogically. The wastes included three Lurgi gasification ashes, two liquefaction residues (SRC and H-coal), a fly ash, and a water-quenched slag. Leachates generated from the solid wastes at various pH levels over the range 2.5 to 11.0 were analyzed for over 40 constituents. Results of the leachate analyses demonstrate the wide variation in constituent solubility for the solid wastes. To help assess the environmental impact of the disposal of these wastes, the leachates were also employed in soil attenuation studies and acute 96-hr static bioassays using young fathead minnows.

Jan 1, 1981

By A. F. Crowley, D. W. G. White

AS part of a continuing program of liquid metals research, the densities of liquid lead, tin, zinc, cadmium, and indium have been measured by a pycnometric method. The pycnometers are made of high-density graphite to the design illustrated in Fig. l(a). In pursuing this research program, emphasis has been placed on detailed experimental care. As a result, claims are made for densities accurate to within ± 0.05 pct over temperature ranges varying from about 100° to 200°C above the melting point. A paper reporting the densities of tin, lead, and Pn-Sn alloys has recently been published,&apos; while papers dealing with

Jan 1, 1969

By Burt C. Mariacher

Extraction of uranium from ores is being accomplished by processes which, for the most part, subject the entire ore to acid or carbonate leaching. Ore deposits with a U3O8 content below 0.10 pct U3O8 are seldom considered suitable for treatment by leaching. A preliminary concentration that would enrich the uranium content of an ore by a simple, low cost process based on physical properties of the ore might result in some low grade deposits becoming commercial ores. In addition, the process might be employed in existing operations to reduce transportation and leaching costs and to increase capacity of existing leaching plants.

Oct 1, 1956

By C. P. Kempter

AS part of a continuing program of liquid metals research, the densities of liquid lead, tin, zinc, cadmium, and indium have been measured by a pycnometric method. The pycnometers are made of high-density graphite to the design illustrated in Fig. l(a). In pursuing this research program, emphasis has been placed on detailed experimental care. As a result, claims are made for densities accurate to within ± 0.05 pct over temperature ranges varying from about 100± to 200°C above the melting point. A paper reporting the densities of tin, lead, and Pn-Sn alloys has recently been published,&apos; while papers dealing with

Jan 1, 1969

By M. C. Dow

INTRODUCTION BELT conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stonecrushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. GENERAL RELIABILITY It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 1/2 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. LOADING THE BELT It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined conveyor to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1947

By C. M. Loeb, T. E. Norman

The use of ball, rod and tube mills for grinding ore, cement and other materials has grown so rapidly during the past forty years that the world&apos;s annual consumption of ferrous grinding media for these mills is now estimated to be between one half million and one million tons per year. Ferrous grinding balls constitute the major portion of this tonnage. Obviously they represent suficient value to justify thorough studies of the factors governing their performance. The selection of grinding balls is governed principally by: I. Quality (wear resistance, impact resistance, soundness, and the like). 2. Sources of supply and delivered cost. 3. Grinding characteristics or efficiency in the ball mill. This paper deals principally with the quality of ferrous grinding balls. In the study of these factors certain data relative to the fundamental nature of ball wear in ball mills have been obtained. These data are also presented and discussed briefly. The Development of a Suitable Wear Test A study of the fundamental factors governing the quality of grinding balls has been hampered seriously by the fact that a competent test has, in the past, involvetd the purchase of several hundred tons of halls of a specific type which were then run in one or more ball mills for a period ranging from several months&apos; to several years&apos; duration. Often, during the period of test, it became necessary to change operating conditions or the character of the ore fed to the test mill with the result that the rate of ball consumption changed and the test figures became of little value. Under such circumstances, progress in the development of better grinding balls, has been necessarily slow. Economic factors and variations in the quality of balls produced by different sources of supply generally make it necessary for each mill operator to determine for himself the most suitable type of balls for his mills. In our own ball mill grinding operations at Climax, Colo., we were faced with this problem. After we had run a few large scale wear tests at considerable expense we decided to investigate the possibilities of a small scale wear test which would be capable of testing numerous types of balls within a relatively short time. The most important requirement of any test is, of course, that it give results which can be used to predict accurately the wear in full scale operations. It was known that Ellis and his associates1&apos;2 had developed a method of testing grinding balls by small scale tests run at the Ontario Research Foundation. Ellis&apos; method of testing was used as a starting point in our investigations. In the course of our tests a number of modifications of the original method were found to be desirable so that, by an evolutionary procedure, a method of small scale

Jan 1, 1949