Search Documents

By E. A. Gulbransen, J. W. Hickman

INTRODUCTION DURING the past two decades considerable progress has been made in the art of manufacturing heater alloys. The conventional iron-chromium-nickel alloys have been improved by the addition of small quantities of other elements. Up to the present time, to our knowledge, there has not appeared a systematic study of these alloys where the newer tools of investigation have been brought to bear on the problem. It is not yet clear what roles the additional elements play in increasing life time in usage. As a first approximation one might guess that elements such as manganese, silicon, zirconium, calcium and aluminum would aid in the formation of a protective film on the alloy surface, thus retarding the oxidation rate and increasing lifetime. If these additional elements do form protective oxides in the outer surface of the oxide film, it may be possible to identify them by means of reflection electron diffraction. It is also possible that the additional elements may not diffuse to the surface but may remain at the interface between the oxide and the metal. Then, too, the major elements in the alloys undoubtedly form oxides which are stratified on the surface. If the minor elements concentrate in a layer in contact with the substrate where they undergo oxidation and if this oxide film offers resistance to the diffusion of iron, chromium and nickel ions, then the lifetime of the heater element might be expected to increase. It is also possible that preferential reduction in the diffusion rates of the several ions may occur to such a degree that oxides may form in the body of the film and on the outer surface which are different from those that would normally form if the additional elements were not present. The use of transmisson electron diffraction may aid us in interpreting these phenomena. Up to the present time all of the factors which influence the lifetime of a given heater element are not definitely known. Among these are: (I) The rate of oxidation of the alloy. This may be dependent upon the composition and the physical state of the alloy. (2) The stability of the structure of the coating which forms. Transitions from one structure to another or solid phase reactions resulting in a change of composition may occur. The tendency of the film to adhere to the substrate when heated and cooled successively will be important. (3) The evaporation of various constituents from the alloy such as the removal of carbon by oxygen in a decarburization reaction. With these possibilities in view, an electron diffraction study of the oxides occurring on six different nickel-chromium alloys was undertaken with the hope that the results of this study could be correlated with oxidation rate studies as determined by means of the vacuum microbalance method1 and with

Jan 1, 1948

By George H. Found

During recent years considerable interest has been focused on the energy-absorption characteristics of metal when it is cyclically stressed in vibration. The most familiar manifestation of this phenomenon, which is called the "damping capacity" or "internal friction" 06 a material, is involved in the dissipation of mechanical energy of vibration, which otherwise would build up to stress levels where the problems of noise and fatigue are involved. In addition to its engineering importance in structures, the damping behavior of metals, particularly at low stress amplitudes, has also been used as a unique metallurgical research tool with which to provide sensitive means for indicating certain structural changes within metals. Important contributions toward understanding the energy-dissipating -mecha-nisms that are responsible for internal friction in metals have been made in the last few years. The information is not yet sufficiently extensive, however, to provide a useful metallurgical concept describing exactly how the structure affects the internal friction, or to encourage more general use of this technique among metallurgists. Three fundamental mechanisms have been proposed, as a result of recent experi- mental investigations, to account for the internal friction in nonferrous metals in low-stress amplitude tests. These include damping due to internal thermal currents that are created and flow in metal because of differential vibratory stress effects,' damping due to localized inelastic stress relaxation at inhomogeneities within the meta1,2,3 and damping related to plastic flow of a localized type for which an explanation has been sought in terms of the dislocation theory.' How each of these mechanisms functions as a result of structural changes in the metal is, in general, not well understood because of insufficient experimental data for which the controlling variables ham been segregated and because of uncertainties in regard to the nature of the structural changes themselves. In several investigations the effects of cold-working on the internal friction of polycrystalline brass and aluminum have been described. As reported by Köster and Rosenthal,5 and by Förster and Breitfield,6 there is an initial large increase in the damping when the metal is worked. The initial high value is not stable, but declines rapidly, at first, in a hyperbolic manner. About Ioo hr. after straining, a stable value is reached of magnitude proportional to the amount of strain.' In Fig. I is shown the relationship found by Zener and his collaborators between the internal friction due to cold-working of alpha brass and the amount of cold-working.8 Several investigators have made internal-friction measurements on worked poly-

Jan 1, 1945

By J. W. Halley

THE effects of tin on steel have become increasingly important because of the necessity of using poorly detinned scrap, tin cans, and terne plate, in the open hearth. Since a tin can contains about 1.5 per cent tin, it would be possible to have up to 0.75 per cent tin in steel made with a 50 per cent scrap charge. In order to use tin-containing scrap, it is necessary to know the effect of tin on various grades of steel. The following investigation is by no means comprehensive but covers a number of steels in which tin content is important. PUBLISHED WORK A number of investigations of the effects of tin on rolling quality and physical properties have been published. It has been found that tin increases strength and hardness and reduces ductility and notched impact resistance. The decrease in ductility and notched impact resistance becomes more marked as the carbon decreases. McKimm1 found no change in Olsen ductility, Rockwell hardness, yield strength, tensile strength or elongation in cold-reduced strip containing up to 0.124 per cent tin. A tin content of 0.15 per cent gave difficulties in rolling and increased the hardness but 0.21 per cent tin showed no change in properties from material containing very little tin. No explanation of this contradiction is offered. Andrew and Peile2 investigated steels containing 0.01 to 0.25 per cent carbon and up to 0.63 per cent tin. They found an increase in tensile strength of from 100 to 200 lb. per sq. in. for each 0.01 per cent tin on normalized samples. The elongation and reduction of area were decreased and the notched impact resistance was reduced markedly. Quenched and drawn samples did not show embrittling if water-quenched from the draw temperature of 1148°F. (620°C.). They could find no evidence of tin under the microscope. Whitely and Braithwaite3 investigated the effect of tin on rail steel containing 0.55 to 0.06 per cent carbon. They found that 0.08 per cent tin caused a marked decrease in elongation, notched impact resistance and the degree of bend. The tensile strength was increased in some tests and not in others. Bolsover and Barraclough4 investigated the effect of tin up to 0.50 per cent on a 0.35 per cent carbon steel and on several alloy steels with from 0.30 to 0.40 per cent carbon. They found a comparatively uniform decrease in notched impact resistance with increasing tin on quenched and drawn samples. If the samples were quenched from the drawing temperature or reheated to the drawing temperature and quenched, the embrittling was much less severe. Steels containing molybdenum suffered much less embrittlement than other steels. EXPERIMENTAL WORK Effect of Tin on Low-carbon Rimmed Steel Increasing quantities of tin were added to four ingots of a heat of the following ladle analysis: carbon, 0.08 per cent; manganese, 0.39; phosphorus, 0.009; sulphur, 0.025.

Jan 1, 1942

By J.W. Halley

The effects of tin on steel have become increasingly important because of the necessity of using poorly detinned scrap, tin cans, and terne plate, in the open hearth. Since a tin can contains about 1.5 per cent tin, it would be possible to have up to 0.75 per cent tin in steel made with a 50 per cent scrap charge. In order to use tin-containing scrap, it is necessary to know the effect of tin on various grades of steel. The following investigation is by no means comprehensive but covers a number of steels in which tin content is important. Published Work A number of investigations of the effects of tin on rolling quality and physical properties have been published. It has been found that tin increases strength and hardness and reduces ductility and notched impact resistance. The decrease' in ductility and notched impact resistance becomes more marked as the carbon decreases. McKimml found no change in Olsen ductility, Kockwell hardness, yield strength, tensile strength or elongation in cold-reduced strip containing up to 0.124 per cent tin. A tin content of 0.1j per cent gave difficulties in rolling and increased the hardness but 0.21 per cent tin showed no change in properties from material containing very little tin. No explanation of this contradiction is offered. Andrew and Peile2 investigated steels containing 0.10 to 0.25 per cent carbon and up to 0.63 per cent tin. They found an increase in tensile strength of from 100 to 200 lb. per sq. in. for each 0.01 per cent tin on normalized samples. The elongation and reduction of area were decreased and the notched impact resistance was reduced markedly. Quenched and drawn samples did not show embrittling if water-quenched from the draw temperature of 1148°F. (620°C.). They could find no evidence of tin under the microscope. Whitely and Braithwaite3 investigated the effect of tin on rail steel containing 0.55 to 0.60 per cent carbon. They found that 0.08 per cent tin caused a marked decrease in elongation, notched impact resistance and the degree of bend. The tensile strength was increased in some tests and not in others. Bolsover and Barraclough4 investigated the effect of tin up to 0. 50 per cent on a 0.35 per cent carbon steel and on several alloy steels with from 0.30 to 0.40 per cent carbon. They found a comparatively uniform decrease in notched impact resistance with increasing tin on quenched and drawn samples. If the samples were quenched from the drawing temperature or reheated to the drawing temperature and quenched, the embrittling was much less severe. Steels containing molybdenum suffered much less embrittlement than other steels. Experimental WoRk Effect of Tin on Low-carbon Rimmed Steel Increasing quantities of tin were added to four ingots of a heat of the following ladle analysis: carbon, 0.08 per cent; manganese, 0.39; phosphorus, 0.009; sulphur, 0.025.

Jan 1, 1943

By J. W. Halley

The effects of tin on steel have become increasingly important because of the necessity of using poorly detinned scrap, tin cans, and terne plate, in the open hearth. Since a tin can contains about 1.5 per cent tin, it would be possible to have up to 0.75 per cent tin in steel made with a 50 per cent scrap charge. In order to use tin-containing scrap, it is necessary to know the effect of tin on various grades of steel. The following investigation is by no means comprehensive but covers a number of steels in which tin content is important. Published Work A number of investigations of the effects of tin on rolling quality and physical properties have been published. It has been found that tin increases strength and hardness and reduces ductility and notched impact resistance. The decrease' in ductility and notched impact resistance becomes more marked as the carbon decreases. McKimml found no change in Olsen ductility, Kockwell hardness, yield strength, tensile strength or elongation in cold-reduced strip containing up to 0.124 per cent tin. A tin content of 0.1j per cent gave difficulties in rolling and increased the hardness but 0.21 per cent tin showed no change in properties from material containing very little tin. No explanation of this contradiction is offered. Andrew and Peile2 investigated steels containing 0.10 to 0.25 per cent carbon and up to 0.63 per cent tin. They found an increase in tensile strength of from 100 to 200 lb. per sq. in. for each 0.01 per cent tin on normalized samples. The elongation and reduction of area were decreased and the notched impact resistance was reduced markedly. Quenched and drawn samples did not show embrittling if water-quenched from the draw temperature of 1148°F. (620°C.). They could find no evidence of tin under the microscope. Whitely and Braithwaite3 investigated the effect of tin on rail steel containing 0.55 to 0.60 per cent carbon. They found that 0.08 per cent tin caused a marked decrease in elongation, notched impact resistance and the degree of bend. The tensile strength was increased in some tests and not in others. Bolsover and Barraclough4 investigated the effect of tin up to 0. 50 per cent on a 0.35 per cent carbon steel and on several alloy steels with from 0.30 to 0.40 per cent carbon. They found a comparatively uniform decrease in notched impact resistance with increasing tin on quenched and drawn samples. If the samples were quenched from the drawing temperature or reheated to the drawing temperature and quenched, the embrittling was much less severe. Steels containing molybdenum suffered much less embrittlement than other steels. Experimental WoRk Effect of Tin on Low-carbon Rimmed Steel Increasing quantities of tin were added to four ingots of a heat of the following ladle analysis: carbon, 0.08 per cent; manganese, 0.39; phosphorus, 0.009; sulphur, 0.025.

Jan 1, 1943

By R. C. Amero

FULLERS earth is a general name applied to claylike minerals that have high natural ad-sorptive powers. They are usually distinguished from ordinary clays by a higher content of combined moisture and a lower apparent density. The definition is based on the ancient use of the material for fulling, or cleansing woolen cloth of oil and grease; a more modern definition should mention the ability to decolorize oil and should differentiate between fullers earth, which is naturally active, and certain bentonites which only develop decolorizing power after being leached with strong mineral acids. The distinction between fullers earth and activable bentonite is not a sharp one, since all types of intermediate clays can be found that are more or less naturally active, yet more or less responsive to acid treatment. The differences seem to depend somewhat on the amount of leaching that has been effected by natural ground waters. Physical Properties The principal mineral constituent of activable bentonite is montmorillonite, a hydrous aluminum silicate to which the following formula is generally assigned: Al,Si,O,, (OH), • 12H,O Fullers earth, as well as bentonite, is usually composed of some variety of montmorillonite, but in the United States the largest tonnage of fullers earth is mined from deposits of attapulgite. Attapul- gite is a clay mineral composed of monoclinic crystals of colloidal size, having a fibrous shape similar to that of asbestos. A sectional model of the attapulgite "molecule" is shown in Fig. 1. A single unit is about 18.0 A wide and 12.9 A high. The length of the molecule is variable, but this same molecular pattern is repeated to form needlework crystals, rather than flakes, as is characteristic of the montmorillonite crystals. Attapulgite has been assigned the following formula,' although actually, the magnesia has been largely replaced by alumina: (0%) . (OH), • Mg, . Si, • Olp . 4H20. The fibrous nature of the mineral is clearly shown in the electron micrograph, Fig. 2. Although the deposits contain 5 to 30 pct quartz and carbonate minerals, impurities in the commercial products are held at a low level, principally by selective mining on the basis of oil decolorizing efficiency. The particle size distribution of this fullers earth has been estimated from settling rates, using sodium citrate as a dispersing agent.' Since Stokes' law only applies to spherical particles, the equivalent particle diameter calculated below is probably more nearly an index of diameter rather than length of the needlelike crystals: Eqnivalent Arbitrary Particle Distribution, Size Diameter Pci Classil3catian 0.05 mm 0.80 0.80 pct sand 0.05-0.02 mm 10.96 0.02-0.01 mm 9.65 42.10 pct silt 0.01-0.005 mm 11.40 0.005-0.002 mm 10.09 2-0.5 micron 10.61 0.5-0.2 micron 29.09 56.58 pct clay 0.2-0.05 micron 14.86 0.05 micron 1.96 The differential thermal analysis shown in Fig. 3 is unique and supports the theory that this is a distinct mineral species.' ~ Other general properties of the mineral as shown in Table I.

Jan 1, 1952

By R. P. McLaughlin

In most branches of the mining industry it is a well-recognized fact that care must be taken to protect the mineral deposit from undue physical injury. It is comparatively easy to grasp this idea when the mineral is a solid and the lives of workmen depend directly upon the care with which it is removed from its natural position, but when the product is a liquid drawn up from pools several thousand feet beneath the surface of the ground through openings only a few inches in diameter, it requires some imagination to picture underground conditions and the changes which must often occur. The development of the petroleum deposits of California has been attended by numerous accidents, the results of which are readily noticed at the top of the wells and in the profit and loss accounts of the operators. Determination of the cause of these accidents has been the subject of considerable study, which naturally has fallen upon men familiar with technical methods. The greatest damage to the oil deposits of California has resulted from water finding its way into the oil-bearing sands, and it is the purpose of this paper to set forth briefly this phase of the oil industry. Much of the material here presented has previously appeared in publications issued by the California State Mining Bureau, which, under the direction of State Mineralogist Fletcher McN. Hamilton, has investigated the subject and taken steps toward improvement of conditions. The writer, having been in charge of this branch of the Bureau work, has gained considerable knowledge of existing conditions. Generally speaking, the oil-bearing formations of California are soft, unconsolidated sand beds, separated by clay strata, which are also soft. Some of the sand beds carry water instead of oil. All of the beds are more or less separated, probably being of lenticular shape. Very few of the beds in the oil fields lie flat or undisturbed over any great area. Folding and tilting are common, and faulting also occurs in some of the fields. The accumulation of oil is not confined to any single structural feature, such as the anticline, but occurs in many other structural features. Water-bearing strata occur in practically every oil field in the State. Complete data are not at hand for a comparison of the damage

Jan 1, 1916

By E. G. Leonardon, D. C. McCann

The search for oil has required, and without a doubt supplies, a tremendous amount of information on the structure, composition, physical properties, and history of sedimentary rocks. The earliest and most complete source of knowledge is the sample or core of the rock itself, the uses of which are well known. The purpose of this paper is primarily to discuss a new method for obtaining these cores, and to illustrate its use in connection with electrical logs. Most cores have been obtained through a special adaptation of rotary drilling, and the results have been remarkably good, considering the mechanical problems involved. Unfortunately, because of the time and expense, this method cannot be used for the entire length of the drill hole. Even though ingenious contrivances have been evolved in order to reduce the time spent in round trips, such as wire-line coring equipment, mechanical coring still remains too expensive to be carried out continuously. In practice, therefore, one is finally compelled to estimate the probable depths of the more interesting horizons and, allowing a wide margin of safety, to core through those sections only. It is true also that interesting results have been obtained by examining the cuttings brought to the surface by the mud circulated in the well during the process of drilling. Be that as it may, the inescapable fact remains that key horizons may be passed inadvertently, for one reason or another, while the drilling operations are being performed. The only continuous record of the formations encountered is that furnished by electrical surveys. Obviously, it would be desirable to make the electrical survey first and to take the samples from the wall of the hole according to the indications on the electrical log. In this way, it would be possible to core only the exact sections desired, eliminating the otherwise inevitable estimates as to the point at which to start coring, and thereby reducing to a minimum this expensive operation. At the same time this method would provide a maximum of useful samples. A device for taking samples of the formation from the walls of a hole therefore offers the possibility of recovering cores from zones otherwise lost as a source of this type of information. Furthermore, by coring

Jan 1, 1939

By E. G. Leonardon, D. C. McCann

The search for oil has required, and without a doubt supplies, a tremendous amount of information on the structure, composition, physical properties, and history of sedimentary rocks. The earliest and most complete source of knowledge is the sample or core of the rock itself, the uses of which are well known. The purpose of this paper is primarily to discuss a new method for obtaining these cores, and to illustrate its use in connection with electrical logs. Most cores have been obtained through a special adaptation of rotary drilling, and the results have been remarkably good, considering the mechanical problems involved. Unfortunately, because of the time and expense, this method cannot be used for the entire length of the drill hole. Even though ingenious contrivances have been evolved in order to reduce the time spent in round trips, such as wire-line coring equipment, mechanical coring still remains too expensive to be carried out continuously. In practice, therefore, one is finally compelled to estimate the probable depths of the more interesting horizons and, allowing a wide margin of safety, to core through those sections only. It is true also that interesting results have been obtained by examining the cuttings brought to the surface by the mud circulated in the well during the process of drilling. Be that as it may, the inescapable fact remains that key horizons may be passed inadvertently, for one reason or another, while the drilling operations are being performed. The only continuous record of the formations encountered is that furnished by electrical surveys. Obviously, it would be desirable to make the electrical survey first and to take the samples from the wall of the hole according to the indications on the electrical log. In this way, it would be possible to core only the exact sections desired, eliminating the otherwise inevitable estimates as to the point at which to start coring, and thereby reducing to a minimum this expensive operation. At the same time this method would provide a maximum of useful samples. A device for taking samples of the formation from the walls of a hole therefore offers the possibility of recovering cores from zones otherwise lost as a source of this type of information. Furthermore, by coring

Jan 1, 1939

By H. E. McKinstry

Movement on a fracture of irregular shape can cause local widening of the fissure and thereby offer freer channelways for circulation of ore-depositing solutions. This influence: coupled with large areas of wall rock available for reacting with ore solutions in brecciated and shattered ground can account for locally active deposition of metals and the resulting ore shoots. Such irregularities in the fracture system may be caused by local variations in the strength of rocks and by pre-existing lines of weakness, especially if these stand at favorable angles to certain components of the fracturing stress. Therefore correct interpretation of the mechanics of fracturing should permit deductions as to structurally favorable places on unexplored portions of the vein system. Introduction It has long been recognized that movement on a curved or irregular fault surface is capable of separating the walls in certain portions of the fault, but until very recent years the importance of this mechanism as a factor in localizing ore shoots has escaped proper recognition. A short time ago W. H. Newhouse' presented a careful analytical study of displacements and their corresponding open spaces. For reasons that will be discussed later, it frequently happens that portions of the vein which are favorably oriented are not merely wider but also richer than the average. In many cases the widening with its accompanying richness coincides with very minor changes in the dip or strike of the vein, irregularities that commonly escape notice unless the vein is mapped in detail and a careful geometrical analysis made. While the relationship between the width of the vein and the changes in dip or strike has been recognized as a matter of observation, the irregularities have been accepted as more or less the result of accident. There has been very little effort except in isolated cases to find out the causes of these changes in dip or strike. Yet it is clear that if the causes can be recognized and expressed in terms of geologic structure the geologist will know where to look for repetitions of these favorable conditions either on extensions of the same vein or on adjoining veins. Any lack of understanding of the causes is due to the limitations of our ability to interpret our observations and not to the sheer capriciousness of

Jan 1, 1941

By H. E. McKinstry

Movement on a fracture of irregular shape can cause local widening of the fissure and thereby offer freer channelways for circulation of ore-depositing solutions. This influence: coupled with large areas of wall rock available for reacting with ore solutions in brecciated and shattered ground can account for locally active deposition of metals and the resulting ore shoots. Such irregularities in the fracture system may be caused by local variations in the strength of rocks and by pre-existing lines of weakness, especially if these stand at favorable angles to certain components of the fracturing stress. Therefore correct interpretation of the mechanics of fracturing should permit deductions as to structurally favorable places on unexplored portions of the vein system. Introduction It has long been recognized that movement on a curved or irregular fault surface is capable of separating the walls in certain portions of the fault, but until very recent years the importance of this mechanism as a factor in localizing ore shoots has escaped proper recognition. A short time ago W. H. Newhouse' presented a careful analytical study of displacements and their corresponding open spaces. For reasons that will be discussed later, it frequently happens that portions of the vein which are favorably oriented are not merely wider but also richer than the average. In many cases the widening with its accompanying richness coincides with very minor changes in the dip or strike of the vein, irregularities that commonly escape notice unless the vein is mapped in detail and a careful geometrical analysis made. While the relationship between the width of the vein and the changes in dip or strike has been recognized as a matter of observation, the irregularities have been accepted as more or less the result of accident. There has been very little effort except in isolated cases to find out the causes of these changes in dip or strike. Yet it is clear that if the causes can be recognized and expressed in terms of geologic structure the geologist will know where to look for repetitions of these favorable conditions either on extensions of the same vein or on adjoining veins. Any lack of understanding of the causes is due to the limitations of our ability to interpret our observations and not to the sheer capriciousness of

Jan 1, 1941

By P. H. Mell

AMONG the minerals exhibited at the Atlanta Exhibition of 1881, soapstone, kaolin, and asbestos were well represented. The first two occur in large quantities, of very pure quality, throughout the South. The last is somewhat limited in amount, yet in certain localities it exists in masses sufficiently large to pay for working; in North Carolina, Georgia, and Alabama it has been mined with some profit. I would, in this paper, call special attention to the minerals soapstone and kaolin, because their many valuable qualities seem to have been al most entirely overlooked by our Southern manufacturers. Steatite, particularly, occurs in such large quantities, and generally in such close proximity to the great iron regions of Alabama and Georgia, that it is amazing that the iron companies will persist in sending abroad under. heavy expense for firebrick. It would require a much smaller sum of money to quarry this rock and place it at the various furnaces ; and the results obtained, I am sure, would prove its superiority over the majority of firebrick brought into this region. Soapstone, as well as kaolin, is found throughout the metamorphic regions of Alabama, Georgia, South Carolina, and North Carolina. Below-will be found seven analyses that I have made of this mineral, taken from various points in the four States above mentioned. I have also subjected these same specimens to severe fire-tests, and the results were very satisfactory. The tests were conducted in the following manner: Small portions of the compact variety were carefully weighed and placed in a Fletcher's new crucible furnace for gas, and subjected for half an hour to a heat that will in 12 minutes fuse iron. The only effect upon these specimens was a slight change in color .to a darker shade, a small loss in weight, due evidently to the evaporation of water, and, in one or two specimens, a slight degree of fusion on the sharp edges. The first specimen subjected to investigation was taken from a large outcropping in Tallapoosa County, Alabama. Specific gravity, 2.88 ; hardness, 1.9; color, blue gray. Composition Water, - 2.68 Silica, - 65.46 Iron oxide, - 2.10 Alumina, - 15.02 Magnesia, - 15.35 100.61

Jan 1, 1882

By Nicholas J. Grant, Oliver Preston

PUBLICATION of data by Irmann' indicating outstanding thermal stability and elevated-temperature strength properties in a sintered aluminum powder product (SAP) stimulated interest in the strengthening of metals by means of a highly dispersed oxide phase. This material was produced by compacting, sintering and extruding a fine flake aluminum powder, resulting in a dense product containing 10 to 16 volume pct alumina, which arises from the thin oxide film on the starting powder, highly dispersed in a matrix of pure aluminum. The method of producing SAP, and the stable high-temperature properties obtained from it, introduced the possibility of developing superior materials for high-temperature service by powder metallurgy methods. The composition of the materials of this type which are presently under consideration is predominantly metallic, containing from less than 1 pct up to about 20 volume pct of the oxide. As a result, other properties of these materials, such as electrical and thermal conductivity, thermal shock resistance, and to a certain extent ductility, notch sensitivity, machinability and hot working properties, are also predominantly metallic. These alloys do not constitute, therefore, a completely new class of materials as do the cermets, but rather present a new means of modifying the properties of a metallic matrix. In this sense, SAP type alloys are more closely analogous to the alloy aging systems. While the strength properties realized in the oxide-pure metal systems at the lower temperatures are substantially less than the best attainable in the aging systems, the thermal instabilities in the latter make them of less value for use at temperature much above their optimum aging temperatures, as indicated in Fig. 1. While the means of obtaining an oxide dispersion are more difficult and costly than conventional aging processes, in the light of the as yet limited understanding of such systems there is considerable promise of improved high temperature properties arising from the thermal stability of these structures. Since the development of SAP in 1946, its properties and the properties of a series of similarAl,O,-A1 products containing from about 1 to 20 pct aluminum oxide have been fairly extensively studied and reported.'- "articular attention has been given to

Jan 1, 1958

By T. A. Dungan

THE thermal processes for the production of metallic magnesium can be divided into two general classifications, the direct reduction of magnesia with carbon and the indirect reduction of compounds of magnesium by reducing agents that are themselves products of carbon reduction. The latter are so chosen as to cause reduction of magnesium compounds wherein only the magnesium is liberated in the vapor phase. Reducing agents used are: calcium carbide, silicon carbide, silicon, aluminum, various silicides or combinations of calcium, aluminum, silicon in iron. All of these are products of highly endothermic reactions and, with the exception of scrap aluminum, can be produced in an open, submerged arc furnace; that is, the arc is covered only by the charge itself. The more investment in energy required to prepare such a reducing agent, the less is the energy required in the subsequent step to reduce the magnesium compound to the metal. It is impossible, however, to avoid the laws of thermodynamics, no matter how much circumambulation is resorted to in the preparation of successively more powerful reducing agents. Since each such step carries forward its own inefficiencies, it appears evident that the ultimate status of such processes is dependent upon the development of by-products. EARLY EXPERIMENTS IN DIRECT REDUCTION The direct reduction of magnesium oxide by carbon has a decided appeal to both the scientist and the industrialist. The successful production of the carbothermic plant at Permanente is a significant fact in the substantiation of this concept. Like most developments, however, the history of carbon reduction of magnesia is not one of triumph after triumph, or immediate heady success to the investigators. It is understood that one of the early investigators conducted an experiment wherein he placed carbon and magnesia in one end of an evacuated tube and managed to heat this end to a temperature high enough that magnesia and carbon deposited at the other end of the tube. The charge, unreduced, appeared to have been completely transported from the hot to the cold end of the tube. This raised doubt for some time as to whether magnesia could be reduced at all with carbon. It was correctly suspected, however, that the magnesia was in fact reduced and the resultant magnesium vapor and carbon monoxide reacted upon one another upon reduction in temperature to reform the starting ingredients. Attempts were then made to dilute the two vapors by passing a considerable stream of hydrogen through an arc furnace charged with magnesia and carbon. Thus by dilution of the products it was expected to obtain metallic magnesium. The results were positive and metallic magnesium was

Jan 1, 1944

By R. F. Mehl, G. V. Smith

THE decomposition of austenite in steels, because of its immense practical importance, has been subjected to extensive study in recent years from the point of view of the mechanism of the process.1-3 Although much information has been acquired a number of questions, principally of theoretical interest, remain. One is that of the atomic-crystallographic mechanism by which each of the various reaction products forms. The isothermal reaction products of the eutectoid decomposition in plain carbon steels (to which this study is restricted) have conveniently been classified in three general groupings-pearlite, bainite, and martensite. Of these several products, pearlite and martensite have been studied extensively, but bainite has received only scant attention. As a result, the mechanism of the formation of pearlite and that of martensite are now fairly well understood while a great deal of uncertainty exists regarding bainite. PEARLITE Pearlite forms from austenite by the precipitation of alternate platelets of cementite and ferrite, which grow into the austenite matrix.2-5 The rate of reaction may be described in terms of a rate of nucleation and a rate of growth 2 3 Mehl and Smiths have attempted to determine the lattice relationships existing between the ferrite in pearlite and the parent austenite. Using a pole-figure method of analysis, it was found that a limited number of ferrite orientations resulted from the decomposition of a single grain of austenite; it was not possible,[ ]decide between two assumed ideal relationships, both of which appeared to account for the experimentally determined pole figure. It was definitely shown, however, that the relationship obtaining was quite different from that determined for the proeutectoid separation of ferrite.7 No attempt was made to determine the habit plane (matrix plane to which the precipitate lies parallel) of the pearlite lamellae. Belaiew8 earlier had stated that the number of directions assumed by the pearlite lamellae in a single grain of austenite was 12 (no details were given) and concluded wrongly, as Mehl and Smith' have pointed out, that the lamellae delineate the {210} planes of ferrite.* MARTENSITE It is known that martensite is a transitional constituent of body-centered tetrag-

Jan 1, 1942

By T. V. Falkie, D. R. Mitchell

Many operational problems in mine haulage cannot be solved economically by conventional analytic or trial and error methods. However, a method of probabilistic simulation, which is based on the fundamental assumption that many of the variables governing any physical system are probabilistic, has been adapted to certain areas of operations research in coal mine haulage. This paper attempts to illustrate how simulation can be used in basic haulage research and what kind of results can be expected. Optimization in this case is performed in terms of locomotive and car movement, as well as best utilization of men and equipment, and is approached primarily from the standpoint of scheduling of the main haulage. Many operational problems in mine haulage cannot be solved economically by conventional analytic or trial-error methods. However, a method of probabilistic simulation, which is based on the fundamental assumption that many of the variables governing any physical system are probabilistic, has been adapted to certain areas of operations research in mine haulage. In many physical cases several probability distributions interact with each other in special ways, and it is not possible to solve for their combined effect in a mathematical equation. This is often true in the case of mine haulage, where such variables as number of empties or loads per trip, travel times, and number of cars or tons produced in a given time are probabilistic. By using a simple example of one secondary haulage segment of a large underground haulage system, this paper attempts to illustrate how simulation can be used in basic haulage research and what kind of results can be expected. Optimization in this case is performed in terms of locomotive and car movement, as well as best utilization of men and equipment. This is the type of preliminary research that will be needed as a first phase in any major haulage study, whether it be a relatively simple economic analysis or a plan for complete automation. The problem of optimization has been approached primarily from the standpoint of scheduling of the main haulage. It is evident that the method of proba-

Jan 1, 1963

By Walter S. McKee

When mixed with common cast steel in quantities ranging from 11 to 131/2 per cent. and properly treated, manganese increases the ductility of the metal and adds greatly to its toughness and resistance to abrasive action, which properties comprise the distinctive characteristics that make manganese steel so valuable for many purposes at the present time.. * At present the manganese-steel foundries of this country have an annual capacity of about 60,000 tons and most of the growth has occurred within the past 10 years. In the early days of the industry it was impracticable to make manganese castings weighing over a few thousand pounds, but at present crusher heads, rolling-mill pinions, and similar castings weighing up to 30,000 Ib. each are produced, and it does not appear that the limit of weight has been reached by a considerable margin. Manganese steel is similar in analysis to ordinary first-class converter metal except that it is high in carbon and contains from 11 to 13.5 per cent. of manganese. From one standpoint manganese steel is similar to malleable iron in that the casting as it comes out of the sand is hard and brittle and must be made ductile by a heat-treating process. The heat treatment is an essential part of the process of making manganese-steel castings and must be properly carried out to secure satisfactory results. The necessity for heat treatment limits the thickness of sections which may be made of manganese steel. Originally the annealing depth was comparatively small, but researches carried on during the past few years have resulted in an increase in the thickness of section up to 51/2 in., which it is possible to treat successfully. Large castings are cored out to a minimum thickness of 51/2 in., thus not only eliminating some of the internal stresses which are invariably set up in a very thick casting, but also reducing the weight and inertia of the piece, an important consideration if the casting is to be a moving part in a machine. At the same time, the thickness of 51/2 in. is sufficient to permit the use of manganese steel for the heaviest classes of machinery.

Jan 1, 1916

By E. A. Gulbransen, W. S. Wysong

THE behavior of tungsten and its surface oxides in oxidizing and reducing atmospheres and in high vacua at elevated temperatures is a question of considerable technical importance. The use of tungsten as a metal or as an important component in alloys in high temperature oxidizing atmospheres has been limited because of the unprotective nature of its oxide film and the volatility of its oxide. This paper will present results of a microbalance study1,2 of the following problems: (I) the oxidation behavior in the temperature range of 25 to 550°C (2) the reduction with pure hydrogen of thin oxide films formed on tungsten, and (3) the volatility of thin oxide films on tungsten. Tungsten is an interesting metal to study for the following reasons: (1) although the oxide to metal volume ratio is greater than one, the oxide is not considered protective, (2) the metal readily oxidizes at temperatures from 300° to 550°C (3) the oxides W02 and WO3 are reduced at temperatures as low as 500°C. by hydrogen, and (4) the oxide W02 is volatile at temperatures from 800 to 1100°C. LITERATURE The oxidation of tungsten in its thin film range has not been studied critically. In the thick film range Dunn3 has made the only systematic study. He found the oxidation rate to obey the parabolic rate law in the temperature range of 700 to 900°C. The temperature variation of the oxidation rate constant was found to follow an exponential law of the Arrhenius type. An inflection was noticed in the temperature plot of the rate law constant at 850 to 900°C. This was attributed to a phase change in the oxides. Scheil4 has studied the oxidation rate at 500 and 700°C over long periods of time and found a linear rate law. This result was interpreted as evidence for the presence of a nonprotective film. Pilling and Bedworth5 analyses of the oxide volume to metal volume ratio would indicate that a compact protective film should form. McAdam and Geil6 have studied the oxidation of tungsten in the thin film range using the interference color method. A parabolic rate law was found. Their curves showed that tungsten oxidizes faster than nickel but more slowly than iron. The lattice structures found in the oxidation of tungsten surfaces have been studied by Hickman and Gulbransen.7 They have reported that W03 is the stable oxide in contact with the metallic substrate up to approximately 600°C while W02 forms first at 700°C. Hägg and Magneli8 have recently reported a study of the lattice structures observed in the tungsten oxides using the X-ray diffraction method. In addition to an a-phase W03 and a d-phase W02, they reported the existence of two new phases. A ß' phase, homogeneous between

Jan 1, 1947

By R. F. Mehl, R. F. Bunshah

A fast amplifier technique has been developed for the measurement of the rate of propagation of martensite in an Fe-29.5 pct Ni alloy. The time of formation of one plate of martensite is 3x10 sec and the rate of propagation is 3300 ft per sec approximately. IT has been known for some time that the plate-like structural unit of martensite forms from austenite with great rapidity. Wiester1 and Hane-mann, Hofmann, and Wiester took motion-pictures of the transformation as it occurs in a 1.65 pct C steel; they demonstrated that a single plate formed fully in the time interval between successive frames, viz., 1/20 sec, thus setting an upper limit. Forster and Scheil,3 using an Fe-Ni alloy with 29 pct Ni, recorded the sonic characteristics of the process electrically, upon an oscillograph, setting the upper time limit at 0.002 sec. Forster and Scheil,~ measuring the change in electrical resistance in the same alloy upon a cardiograph, set a limit of 0.02 sec. Forster and Scheil5 later, employing the same alloy, improved their technique, reporting an upper limit of 7.10 sec. In studying signals of such short duration, it is an important question whether the frequency response of the electrical system used is high enough compared to frequency of the pulse measured, or, put differently, whether the system is able to reproduce without distortion the signal arising, in this case, from the formation of a single martensite plate. Forster and Scheil (referring only to their last paper) obtained signals of a frequency of 30 kilocycles (hereinafter kc); this was about the frequency response of the equipment used; thus, if the signal had a frequency higher than 30 kc, it would still appear as a signal of frequency 30 kc. All of these results thus provided upper limits only. Recent developments in electronics have made available equipment with very high frequency response, very high sweep-speeds, high gain, etc. The electrical characteristics of such equipment, used in the present study, are given in Table I. Such equipment offers obvious attraction in the study of the rate of propagation of a martensite structural unit—and perhaps of other structural alterations proceeding at a very high rate. This paper reports an attempt to develop a technique employing such equipment to measure the time of propagation of a martensite structural unit and the variation of this with temperature, with the mode of formation—athermal and isothermal—in both polycrystalline and single-crystal samples; and from such measurements to obtain the rate of propagation. As will be seen, the results obtained are useful theoretically. Materials All data presented here are for an Fe-Ni alloy of the following analysis: 29.5 pct Ni, 0.027 pct C, 0.135 pct Mn, 0.094 pct Si, balance Fe. There were several reasons for choosing this alloy: 1—it is substantially the one used by previous investigators; 2—it exhibits both the athermala and the isothermal' mode of formation of martensite, both studied in detail by Machlin and Cohen; 3—the subzero temperatures of transformation in this alloy are experimentally very convenient; 4—it exhibits the "burst phenomenon";" 5—the change in electrical resistance upon the formation of martensite, a decrease, is great, approximately 50 pct.' The polycrystalline specimens were in the form of wires of 0.025 in. diameter; the single crystals were 1x1/4x1/4 in. Experimental Methods Electrical Apparatus: Fig. 1 is a schematic drawing of the electrical circuit used. The principle used in these measurements is the same as that used by Forster and Scheil." A small direct current, about 1 to 2 amp, is passed through the sample. When a martensite plate forms, the resistance of the sample changes and a high frequency signal is generated. This signal is picked up by the probes attached to the sample, fed into the bank of amplifiers and thence to the vertical deflection plates of a cathode-ray oscilloscope. The signal itself triggers the oscilloscope trace which flashes across the tube face and is photographed by means of a 35 mm movie camera at the end of a light-tight hood. The camera has no shutter. As soon as the signal flashes

Jan 1, 1954

By Paul J. Fopiano

SOME relationships between the flow characteristics of iron single crystals of 99.9 pct purity and the behavior of imperfections have been investigated. X-ray rocking-curve measurements and etch-pit counts were made as a function of plastic strain, and compared to the stress-strain curve obtained on a modified Polyani tensile machine. Crystals grown from rolled strips of vacuum-melted iron by the strain-anneal method1 had a high preference for a (110) longitudinal direction and a (211) face normal. The tensile specimens were prepared from 2 by i by 0.040 in. single crystals having a gage area of 3 by \ in. Rocking-curve measurements were carried out with a highly perfect germanium monochromating crystal in which the dazz spacing was matched to that of the dZl1 in the ir0n.l Well-collimated CuKal radiation was used throughout. These procedures practically eliminated errors due to geometrical and wavelength resolution. Inasmuch as the rocking-curve half breadth may vary markedly from point to point in the specimen being irradiated, the crystals were strained in place by mounting a hydraulic loading device on the double-crystal spectrometer. The rocking curves were taken after each increment of strain in the unloaded condition, since no observable difference was found in the rocking-curves between the loaded and unloaded states. The rocking-curve half breadths of the as-grown specimens were in the range 90 to 120 sec of arc when the beam irradiated an area of about -£ by -& in. on the specimen. DeMarco and weiss3 have shown that, for a well-colli- mated X-ray beam, irradiating about 10"! sq in. of the very same material, half breadths within 10 pct of the Darwin natural half breadth were observed. Since the rocking-curve specimens were stressed by the load-unload technique, the strain achieved at any given stress depended on the time of holding because of low-temperature creep. Fig. 1 shows the rocking-curve half breadth (also area/peak height) as a function of plastic strain for a relatively short holding time (2 to 5 min) at each stress level. For strains less than 0.1 pct the rocking-curve breadth is essentially constant; it is only for larger strains that there occurs a significant increase in this breadth. Where the holding times at each stress level were longer (by well over an order of magnitude) there occurs a significant increase in the rocking-curve breadth only after plastic strains of the order of 0.6 pct had been introduced into the specimen. This observation is related to the time dependence of creep phenomena and emphasizes the difficulty in comparing data obtained by two such different straining methods. Etch-pit results were obtained using a 2 pct nital etch on specimens strained in the range of 0 to 1 pct. Prior to etching, all specimens were annealed for 3 hr at 150°C, the carbon content being sufficient to decorate the dislocations for strains of at least 1 p~t.~ The data points were all taken from parts of the same single crystal which had been strained with short holding times at stress in increments of strain of the order of tenths of 1 pct. The (211) plane is particularly difficult to etch-pit in vacuum-melted iron and therefore it is felt that these values are as much as an order of magnitude low. Fig. 2 shows the etch-pit density as a function of plastic strain. The smooth curve passing through the data points is not meant to infer a quantitative correlation with the rocking-curve data. What is of interest, however, is the change in etch-pit density in the region of 0.2 pct plastic strain. The first three increments in strain (points 2,3, and 4) did not produce a measurable change in the etch-pit density while subsequent increments did produce a measurable change. While the absolute values of these results do not appear to be cor-

Jan 1, 1967