Search Documents

By William R. Webster

The unusual interest taken in the papers on steel at the New York (1922) meeting showed that the time is ripe for the renewal of the general discussion of the physics of steel, on the same lines that wete used formerly and produced such good and lasting results. The curves shown in Figs. 1 to 4 and the appendix were added to my paper1 after the February meeting, but, unfortunately, Figs. 1 and 3 were transposed; the curves on page 252 are for bessemer steel and belong on page 254; while those on page 254 are for open-hearth steel and belong on page 252. These errors are evident at once on referring to the data in Tables 1 and 2, pages 227 and 228. The curves for each 0.05 per cent. of carbon and manganese in basic open-hearth steel are given in Figs. 1 and 2; these lines for the lower carbons and manganese are comparatively uniform. Figs. 3 and 4 give similar lines for carbon and manganese in bessemer steel. The large break in the carbon lines from 0.55 per cent. to 0.60 per cent. is caused by much higher silicon in the steels of 0.60 per cent, carbon and over that are used for springs, etc. The estimated ultimate strength of pure iron, and the increase in strength by carbon, phosphorus, and manganese, with the different views regarding the same, were given and diseussed. All of this can be considered as an introduction to the practical use that is now being made of such data in selecting the heats of steel best suited to give the required physical tests called for in the finished rolled material. The chemical composition of the steel, of course, tells only a part of the story, as many other factors that have an influence on the physical properties of the steel must be considered, and controlled as far as is possible. Some of these have already been referred to, but there are other important ones to be considered and discussed.

Jan 1, 1923

By William R. Webster

The unusual interest taken in the papers on steel at the New York (1922) meeting showed that the time is ripe for the renewal of the general discussion of the physics of steel, on the same lines that wete used formerly and produced such good and lasting results. The curves shown in Figs. 1 to 4 and the appendix were added to my paper1 after the February meeting, but, unfortunately, Figs. 1 and 3 were transposed; the curves on page 252 are for bessemer steel and belong on page 254; while those on page 254 are for open-hearth steel and belong on page 252. These errors are evident at once on referring to the data in Tables 1 and 2, pages 227 and 228. The curves for each 0.05 per cent. of carbon and manganese in basic open-hearth steel are given in Figs. 1 and 2; these lines for the lower carbons and manganese are comparatively uniform. Figs. 3 and 4 give similar lines for carbon and manganese in bessemer steel. The large break in the carbon lines from 0.55 per cent. to 0.60 per cent. is caused by much higher silicon in the steels of 0.60 per cent, carbon and over that are used for springs, etc. The estimated ultimate strength of pure iron, and the increase in strength by carbon, phosphorus, and manganese, with the different views regarding the same, were given and diseussed. All of this can be considered as an introduction to the practical use that is now being made of such data in selecting the heats of steel best suited to give the required physical tests called for in the finished rolled material. The chemical composition of the steel, of course, tells only a part of the story, as many other factors that have an influence on the physical properties of the steel must be considered, and controlled as far as is possible. Some of these have already been referred to, but there are other important ones to be considered and discussed.

Jan 1, 1923

THE increased demand for titanium alloys with improved high-temperature creep strengths has stimulated interest in silicon as an alloying addition to titanium. Silicon is a potent solid-solution strength-ener and, if added in sufficient concentration and properly heat-treated, can also dispersion-strengthen titanium by eutectoid decomposition.' However, better understanding of the nature and distribution of the resulting silicide dispersion in more highly alloyed titanium matrices is necessary for the development of useful titanium alloys which utilize the latter strengthening mechanism. This note describes the chemical and crystallographic characteristics of the silicide phase as it occurs in a typical high-temperature near-a titanium alloy matrix. Several Ti-6A1-3Sn-3Zr a11oys containing various amounts of silicon ranging from 0.1 to 1.0 pct were melted as 10- to 20-lb ingots and processed into 1/2-in.-diam bar stock. The microstructures of specimens annealed at various temperatures were conveniently summarized by the (Ti-6Al-3Sn-3Zr)-Si pseudobinary phase diagram illustrated in Fig. 1. Comparison with the Ti-Si equilibrium diagram indicates the substitutional solutes (Al-Sn-Zr) increase the eutectoid temperature and decrease the a terminal solubility. Annealing at temperatures sufficiently high to dissolve the silicon in a ß solid solution and cooling rapidly enough to preclude coarsening generally produced a uniform dispersion of fine silicide particles, whereas annealing at temperatures near but below the ß transus produced relatively coarse silicide particles. Annealing in the limited a, plus 3 region produced a duplex coarse and fine silicide array. Several a-annealed specimens were examined by X-ray diffraction to determine the crystallographic identity of the precipitate phase. Copper Ka X-ray diffraction patterns of bulk specimens which contained 0.5 and 0.8 pct Si were virtually identical to that of the silicon-free Ti-6Al-3Sn-3Zr base alloy except for a slight shift in some of the high-angle diffraction lines. Apparently the silicide volume fraction was too low to be detected in bulk specimens. X-

Jan 1, 1969

By K. R. Evans

The deformation mechanisms occurring in polycrys-talline, commercially pure titanium and a Ti-8 pct A1 alloy have been investigated and compared to earlier results by Levine on high-purity titanium single crystals and by Conrad on commercially pure titanium. In accord with Levine, two consecutive deformation mechanisms are observed to exist below 500°K with the transition temperature between mechanisms, Tc, strongly dependent upon interstitial composition. T, is found to be 210°. 375° -430°, and 450°K for alloys A large number of investigations have been conducted to determine the rate-controlling mechanisms of plastic deformation occurring in fcc and bcc metals. Very few investigations of a similar nature have been conducted for hexagonal metals. In fact, until very recently, magnesium is the only hexagonal metal which has been systematically investigated for determination of the rate-controlling deformation mechanisms.1"3 From these investigations, it was concluded that basal slip below 420°K occurs by the intersection of forest dislocations,1'3 while for prismatic slip the Peierls mechanism is rate-controlling at low temperatures with interstitial compositions of 0.024, 0.42, 0.61, and 1.13 at. pct expressed in terns of oxygen equivalents. The low-temperature mechanism is found to be an impurity obstacle mechanism in contrast to Levine's earlier conclusion of the Peierls barrier. Measurement of the activation parameters for deformation and estimation of the force-distance profile of the obstacles show their retarding force to be effective over longer distances from the obstacle as the interstitial composition increases. and thermally activated cross slip at higher temperatures. 2 The potential technological importance of titanium alloys has prompted recent studies of the deformation and fracture characteristics of titanium and its alloys. 4-8 Levine' systematically investigated the low-temperature deformation behavior of high purity titanium single crystals oriented for either basal or prismatic slip. It was concluded that the Peierls mechanism was rate-controlling at temperatures below 210°K, while above this temperature an undefined mechanism was rate-controlling. Conrad 7,8 concluded from an analysis of the composition dependence of the critical shear stress at 0°K and measurement of the activation parameters that the low-temperature deformation of titanium is controlled by an impurity

Jan 1, 1969

By George Enos

As the coating formed affects the corrosion rate, duplicate samples of eight non-ferrous alloys were placed in flowing mine water. The alloys tested were as-cast or as-rolled and machined or polished. The paper describes the tests and gives the corrosion losses and the appearance of the samples at the end of the test. AN IMPORTANT factor affecting the rate and nature of corrosion of metals and alloys is the film, or coating, formed on the surface; and this may accelerate or retard corrosive action once started. The formation of films and coatings is intimately associated with the chemical composition and physical constitution of both the metal and the corroding medium. A film or coating may be either the corrosion product resulting from oxidation; that is, an oxide or salt, or a deposition of suspended matter from the corroding media upon the surface of the metal, or a mixture of both. The coating may adhere tightly or loosely to the surface of the corroded metal. In short, a film or coating is the reaction product of the corroding medium and the metal, which adheres to the surface of the metal and with which may be intermingled material from the attacking media not concerned in the chemical reactions. As the, terms film and coating are used by different writers for very different things, distinction is made between the two, by the present writers, on the basis of thickness. Thus, a film is defined as a corrosion product or deposition, on the surface of a corroded metal, that is of such thickness that it cannot be measured by the metallurgical microscope. A coating, on the other hand, is of such thickness that it can be measured. If the resolving power of the 2 mm. (equivalent focal length) apochromatic oil immersion objective (N.A. 1.4) is taken as the limit of the microscope, the limiting resolution is two lines that are 0.0002-0.0004 mm. apart. It is thus possible to measure coatings that are greater than 0.0002-0.0004 mm. thick. This thickness is equivalent to 200,000-

Jan 7, 1924

By C. H. Curtis

THE valuable mineral content of the current feed to the Miami concentrator is as follows: copper, 0.7 pct total; molybdenum, 0.01. Flotation of this ore yields a sulphide concentrate containing: chalcocite, 44 pct; molybdenite, 0.5; pyrite, 50.0; insol, 5.5. A combination of potassium ethyl xanthate and pentasol amyl xanthate as collectors, and pine oil, as frother, are used in this flotation. Rejection of pyrite is encouraged by holding the amount of collectors used to the minimum consistent with copper recovery and by operating at high alkalinity (equivalent to 0.35-0.40 lb CaO per ton solution of pH 11.0).

Jan 1, 1950

By Hugh O?Neill

IN PREVIOUS papers,1 the author has reported the results of experiments on the straining in tension of a single crystal test piece, about 0.6 in. long, of vacuum-melted electrolytic iron containing 1.8 per cent. of silicon. The crystal was originally in the "as cast" condition, and was stressed slowly along a tetragonal axis so that slipping along conjugate gliding planes finally transformed the original cylindrical portion into a pair of fracture wedges. One of these fracture wedges was sectioned along the stress axis in a plane at right angles to the edge of the wedge. A metallographic study of this plane of -section led to the conclusion that slip had taken place in the (111) direction along (112) planes making a V shape with the stress axis. The present paper describes the results of scratch-hardness tests conducted on the same section, in order to determine the distribution of strain hardness therein, followed by annealing, and considers the resulting variations in hardness. These observations supplement those made by Krivobok2 on similar material reduced 25 per cent. by hammering (i. e., by impact) in the cold. In order to investigate ageing effects, two small crystals of the same alloy were also tested.

Jan 1, 1928

By G. L. Oldright, T. B. Brighton, C. M. Dice

The base bullion from the lead blast furnace contains varying amounts of the impurities left in the smelter feed by the concentrator, regardless of the method of smelter operation. These impurities may be held in part in mechanical suspension rather than being present as true alloys. However, usually there is little free space in the crucible in which to separate these drosses before the bullion is taken from the lead well. When such a dross is melted in a laboratory crucible and allowed to cool, the products obtained are lead bullion, speiss, and matte in well separated layers. Typical analyses of layers are: Analyses. Per Cent Element Bullion Speiss Matte Pb.............................................. 92.0 41.2 38.3 Cu.............................................. 2.4 36.3 40.6 As............................................... 4.0 16.5 4.3 Sb............................................... 0.7 0.2 0.4 S................................................ 0.6 1.9 13.1 Fe............................................... 0.0 0.0 0.0 Totals......................................... 99.7 96.1 96.7 The absence of iron in these products drossed from the blast-furnace bullion proves that the impurities for the greater part are not simply finely divided blast-furnace speiss or matte that has been dissolved or dispersed in the lead, but are held in solution by the liquid metal and rise to its surface as infusible compounds when the temperature of the bath is lowered. In general, the drosses made locally are metal sulphides and arsenides and not oxidized compounds. The large content of metallic lead also does not seem to be retained because of oxidized compounds

Jan 1, 1937

By Nathaniel Herz

The use of zinc dust for precipitating the pecious metals from cyanide solutions is well established now in many places, and has many advantages over the shavings method of precipitation. Although much work has been done o,n methods of testing zinc dust, as yet. no absolutely positive test has been devised to determine the value of the material. Certain facts are known, but often it happens that results on a working scale are not as expected from the laboratory tests. The purpose of this paper is to record some obscrvations made while testing a large variety of zinc-dust samples in the laboratory. W. J. Sharwoodl has described standard analytical methods, which have been followed, with the changes noted. The regular determinations include zinc oxide, by solution in ammonia and ammonium chloride, lead, and precipitating efficiency. In some cases cadmium was determined by a method similar to that described by J E Clennell.2 I will discuss the precipitating-efficiency test in detail. The procedure is as follows: "A solution of potassium silver cyanide is prepared by dissolving 10 grams of silver cyanide (AgCN) and 5 grams of 99 %' potassium cyanide in a little water and diluting up to 1000 cc. It is then adjusted by addition of a little more XCN or AgCN until the solution indicates from 0.12% to 0.15% free KCN by titration with standard silver nitrate. The titration is best made by using a 10-cc. or 20-cc. sample, adding 1 CC. of 2 % potassium iodide, and a slight excess of ammonia, as the end point is then sharper. Or 15 grams of pure crystallized XAg(CN)2 may be dissolved in a liter of water and 1.5 grams XCN added. " Weigh out 0.5 gram zinc dust into a 300-cc. beaker. Add a few cubic centimeters of watcr and stir until zinc is well mixed, then pour in 250 cc. of the prepared solution, stirring vigorously. See that all lumps are broken up, and continue stirring for fully five minutes. Stir occasionally (at least every 10 minutes) until the end of two hours from the addition of the solution. Then filter upon an 11-cm. filter, wash precipitate thoroughly, sprinkle with test lead, wrap it carefully in the paper, place in a scarifier with about 20 grams test lead, burn paper cautiously in muffle, scorify five minutes, cupel at low temperature and weigh silver. Milligrams silver obtained from 0.5 gram zinc X 0.0606 = percentage precipitating efflciency."³

Jan 1, 1916

By I. L. Dillamore

A purely geomentrical analysis based on oriented-growth relationships is presented to derive annealing-texture orientations in bcc metals from their- known deformation textures. The analysis takes as its starting point a description of- the bcc deformation texture and follows previous work on fcc metals in considering pvobable nurleation sites for recrystallization and the textural limitations on grains growing into a deformed matrix. The analy-sis accounts for the prominent and the minor coinponents of the annealing textures formed from two the deformation textures and can account for the ob-sem:ed temperature dependence of the annealing texture of bcc metals. THERE have been a number of investigations of annealing textures in bcc metals but few attempts to relate these textures to the deformation textures. This has been largely due to the lack of definition of both annealing and deformation textures, neither of which shows sharply defined orientations. It is, however, necessary to get a better understanding of primary recrystallization textures in bcc metals in view of increasingly exacting demands upon the quality of steel sheet for drawing purposes and as a necessary step towards the control of textures through processing. An analysis is presented here which relates annealing textures to deformation texture, by a purely geometrical method. This takes as its basis the oriented-growth theory of recrystallization and makes some reasonable assumptions regarding the make-up of bcc deformation textures and the limitations on growth relationships in bcc metals. Detailed information on this latter point is not available at the present time, and the present analysis may need to be streamlined or extended when such information is at hand. It is felt, however, that despite these limitations the analysis provides useful results and a valuable aid towards understanding the effect of processing variables. 1) BCC ROLLING TEXTURES Different workers have used a variety of descriptions for the texture developed in bcc metals by rolling. For the present purpose it will be assumed that two different deformation textures can be obtained: 1) a texture containing a major (112)[li0] component and a minor (001)[1i0] component for which increasing deformation causes the (001)[li0] component to increase at the expense of the (112)[li0] component, as suggested by Dillamore and ~oberts' (this is the texture predicted to arise starting from randomly oriented material); 2) a t~xture containing the above components and (111)[110] and (ii1)[112] components. This texture could arise from a material with an initial (110)[001] or (iil)[112] texture. It is well-known that the (ll0)[001] orientation rotates to (ii1)[112]that on roll-

Jan 1, 1965

By Paul B. Crawford, Bobby L. Landrum

Electrical model studies have been made of the effect of unsymmetrical vertical fractures on production cnpacity. The study war restricted to the case of two vertical fractures originating at the well and extending out into the reservoir for various distances and orientations. The ratio of the short fracture length to the long fracture length was varied from 0.1 to 1.0 in successive studies. The angle separating the two fractures was varied from 0 to 180 degrees. The most effective fractured patterns were obtained when the fractures were oriented 180 degrees. It was found that when the total fracture length was equal to 0.2 of the drainage radius, the increase in production capacity may vary from approximately 1.55 to 1.95. depending upon the ratio of the short fracture length to the long fracture length and the angle separating the two fractures. If the total fracture length were 0.5 of the drainape- radius. poroduction cavacitv., increases varving 1.95 to 2.65 were observed, depending on the angle between the fractures and the ratio of the .short fracture length to the long fracture length. The fractured well production capacity decreased aPproxin?ately I to 10 per cent as the angle separating the fractures was varied from 180 to 90 degrees. It was dependent on the particular fracture. The commercial application of reservoir fracturing techniques has caused an interest to be expressed in the effect of vertical and horizontal fractures on production capacities. Some data have indicated that substantially vertical fractures may be created in some reservoirs. It is believed that the fractures are possibly unsymmetrical, that is, one fracture may extend due north 100 ft and a second fracture on the opposite side of the well may extend south or southeast only 50 ft. The total fracture length, ratios of the lengths and angles of separation may vary considerably. For this reason variations in these factors were considered. The study was restricted to the case of two vertical fractures originating at the well and extending out into the reservoir. It is not known that such will occur in a reservoir, but the results may be of value in interpreting or studying fracturing applications. PROCEDURE An electrical model was used in this study of the effect of unsymmetrical vertical fractures on production capacity, A wooden tank 30 in. in diameter and approximately 2 in deep was coated with paraffin wax. A copper band was situated at the periphery and a single wire electrode was positioned at the center of the tank. The ratio of the reservoir radius divided by the

Jan 1, 1956

By T. D. Guldem, J. L. Kaae

ALLOYS with nominal composition of 45-Fe 35-Ni 20-Cr, ASTM-B-163, known under the commercial names of Incoloy 800 and Sanicro 31 (Alloy 800), are often employed at elevated temperatures for extended periods. Therefore, knowledge of the aging behavior of these alloys is of considerable importance. Significant decreases in ductility and increases in yield strength have been observed in the 45-Fe 35-Ni 20-Cr alloys containing about 0.4 pct Ti and 0.4 pct A1 after long-term aging at 540" to 700"~."~ However, no direct evidence has been presented for precipitation phenomena that might result in such changes. Strengthening effects have been attributed to the effects of local or-dering.3 Since y' precipitation (Ni3A1, Ti) is known to occur in similar alloys which contain more titanium and aluminum,4-7 it was decided to explore the possibility that y' might precipitate in these alloys and might be responsible for the changes in mechanical properties on aging. This note reports some observations of two distict types of matrix precipitates made by means of transmission electron microscopy, in a 45-Fe 35-Ni 20-Cr alloy containing 0.31 pct Ti and 0.4 pct Al. The steel used in this investigation was obtained from the Sand-vik Steel Works; it is designated Sanicro-31 (Alloy 800). The chemical composition of the alloy is given in Table I. Aging of solution-treated material at 700" and 800°C for 130 and 100 hr, respectively, produced the matrix precipitates shown in Figs. l(a) and l(b). It is apparent from these micrographs that the precipitate particles occurred in the form of thin square plates parallel to the matrix cube planes. Extraction replication and selected-area electron diffraction showed that the precipitates were M23C6. Coherency strains, consistent with the semicoherent nature of small M23C6 precipitates,' were evident for certain imaging conditions. In addition to matrix precipitation, preferential precipitation of M23C6 on dislocations was common, as has been reported previously for austenitic stainless steels.'" Specimens aged for longer times (-300 hr) at 700°C exhibited a different type of coherent matrix precipitate in addition to the M23C6. An example is shown in Figs. 2(a) and 2(b). In addition to the few large M23C6 precipitates, small precipitates exhibiting strain contrastl0,ll are present. The "line of no contrast" of the strain field of a given precipitate lies along differ-

Jan 1, 1970

By F. R. Cattoir, R. W. Kimball, C. T. Anderson, V. V. Donaldson

THIS paper is the second of a series on the effect of various elements on hot-working characteristics of Fe-C alloys to be issued by this laboratory. The investigations being conducted at the Ferroalloy Research Branch of the U.S. Bureau of Mines, Redding, Calif., involve fundamental research on the effects of various alloying materials and impurities on the physical properties of high purity Fe-C alloys. This paper deals with the determination of the limit of forgeability of steels containing varying amounts of manganese and sulphur. A paper discussing the hot-working characteristics and the physical properties of the forgeable alloys is being prepared. One of the principal impurities in all steels is sulphur.. The phenomenon, hot-shortness, commonly attributed to sulphur, has long been a source of expense and inconvenience to both the maker and user of steels. In steelmaking practice, this effect of sulphur has been overcome by the addition of manganese which, apparently, acts as a desulphurizer. Manganese is also used as a deoxidizer and alloying material. The critical and strategic position of man- ganese gives added importance to research which may contribute to its conservation and more effective utilization. It is not the purpose or intention in the present paper to give any explanation of the mechanism of either hot-shortness or its prevention but rather to report the results of forging high purity Fe-C alloys of the range of compositions near the limit of hot-forgeability. Temperatures for each phase of reduction were duplicated within 20" to 30°F for all tests. The starting material was sponge iron, which, after melting and purification, gave a high purity iron containing about 0.001 pct each of silicon and phosphorus. Scrap iron was not considered suitable because of its high percentage of contaminants and wide variation in analyses. The sponge iron was melted and refined for melting stock in a three-phase, direct-arc, size ST, Moore Rapid Lectromelt furnace with a 500 kva rating as described in the preceding paper. Additives were carefully selected to avoid addition of contaminants. The sulphur was added as resublimed flowers of sulphur or purified roll sulphur of analytical grade. The manganese used was dehydrogenated high purity electrolytic material produced by the Bureau of Mines plant at Boulder City, Nev. High purity aluminum in the form of wire was used for deoxidation. The limestone was obtained locally and had the following analysis: CaO, 53.7 pct; MgO, 0.8; ignition loss, 42.4; R2O3, 0.2; SiO2,3.0; and P2O5, 0.014.

Jan 1, 1955

Located 19 km (12 miles) north of the Carlin gold mine and 43 km (27 miles) north of Carlin, Nevada, is Carlin Gold Mining Company's Bootstrap mine. This deposit is similar in character to the Carlin ore, except it occurs in the upper plate formation of the Roberts thrust fault rather than in the lower plate rocks. The deposit was discovered over 50 years ago and operated on a small scale in the early 1960s using vat cyanide leaching. Newmont Mining Corporation acquired the property in 1967, and from an open pit mined 650,000 mt (717,000 st) of ore which was trucked to the Carlin conventional cyanide plant. (See Gold and Silver Cyanidation Plant Practice by F. W. McQuiston, Jr. and R. S. Shoemaker, Society of Mining Engineers, AIME, 1975. ) With the same grade of ore, the gold recovery by conventional methods is somewhat lower than that of the Carlin ore, even with a finer grind. Leaching tests were first conducted by the United States Bureau of Mines in 1968; and in 1971, ‘72, Carlin conducted extensive cyanidation investigations by bottle testing, simulated heap leaching in tall columns, and small scale pad heap leaches. Gold extractions ranged from 55% to 95% with low reagent consumptions. In 1974, a 545 mt (600 st) heap leach test was made at Carlin on pit-run low-grade material assaying 1.37 g per mt (0.04 oz per st). In a six week period the extraction of gold was 47.57'0. Carlin uses atomic absorption analyses on cyanide leach liquors to determine potential leach ore grade rather than fire assaying because it gives a more practical assessment of leach recovery than does fire assaying, which accounts for the total gold content. Before open-pit mining was started, plans were made to heap leach, the ore at Bootstrap which was too low grade for transport to Carlin. The topsoil outside of the designed pit area overlaid ancient lakebed clays which were found suitable for compaction to form an impervious base on which the dumps to be leached could be placed. By using the cost of truck haulage and milling at the Carlin plant and the price of gold 'at that time, a cutoff grade was established which resulted in the gold content of the first 150,000 mt (165,000 st) of the heap leaching ore being 1.51 g per mt (0.044 oz per st). An additional 500,000 mt (552,000 st) of lower grade material, assaying 0.96 g per mt (0.028 oz per st), is available for leaching as economics permit.

Jan 1, 1981

By C. E. Mills

STUDIES of ground movement and subsidence resulting from mining operations cover a broad field. It is also a very important consideration and one that eventually affects nearly every mining operation of any extent. The damage to surface buildings, removal of mine surface plants and replacements of main hoisting shafts must reach an astounding expenditure were these cost figures available over a period of years. Were the subject one of mathematical formula and dependent only on the angle of draw of the walls or country rocks, the problem would be relatively simple. Consideration must be given to depth and extent of workings; structural conditions of the orebodies and enclosing country rock; physical properties of these same rocks, including schistosity, bedding, jointing, slips, dikes, faults, and other structural weaknesses. The method of mining, extent of openings, supporting pillars, and amount of moisture or water underground are other pertinent factors. With such a large number of variable factors, it is apparent that the subject of subsidence is one that must be based largely on experience and results at other mines where conditions are somewhat comparable. In presenting this paper, it is the intent to describe the progressive results of past ground movements at the United Verde, to bring out physical conditions largely responsible for this movement, but to refrain from theorizing on the ultimate extent of subsidence resulting from future mining operations.

Jan 1, 1934

By Jesse O. Betterton

In the Parkes process of lead refining, after desilverization has been completed by means of zinc additions, there will remain in the lead from 0.5 to 0.6 per cent zinc. At this stage in the refining practically all impurities are reduced to refined lead specifications except zinc and antimony. All excess of copper and nearly all the arsenic goes out with the silver. Silver remaining should not exceed 0.1 oz. per ton. It thus remains only to remove zinc and antimony to produce refined lead. The older practice was to complete refining by means of oxidation processes in reverberatory furnaces. Essentially this consisted of heating the lead to 1200' to 1300" I?. and allowing it to come in contact with a considerable excess of air passing through the furnace, or accomplish the same result by blowing the lead with steam by means of pipes introduced for that purpose, at the same time allowing air to enter the furnace. Usually some procedure involving alternate oxidation and reduction with fine coal or coke was employed in order to reduce the weight of dross or skim finally removed from the furnace. This practice had many elements of weakness in that the main flour of lead, after the preceding expensive operations had been performed, and the whole refining process nearly completed, was subjected to an operation at a comparatively high temperature, which involved much lead loss if the furnaces were not on bags, and the production of 3 to 5 per cent of the weight of the lead as dross or skim, which had to be resmelted and the lead either refined or produced as antimonial lead. In addition, the operating expense of the process was a considerable item. The process of dezincing with chlorine was developed as a substitute for the foregoing described oxidation process, and finally resulted in such advantages as nearly equal operating costs, a practical elimination of the lead loss, and the direct production of a very valuable byproduct, zinc chloride, that may be sold as such or retreated for its zinc and chlorine contents, both of which can be reused in the refining processes. Essentially this process consists of circulating the lead by means of a pump in a kettle through a closed reaction cylinder, gaseous chlorine entering the reaction cylinder with the stream of lead from the pump. Molten zinc chloride is thus produced and is discharged together with

Jan 1, 1937

By W. R. Clough, M. E. Shank

IT has been noted in a study of the flow and fracture of nodular cast iron under biaxial stress conditions (complete results of which will be published later) that when this metal is subjected to stress it may undergo a striking density change. Such behavior was first determined by strain gage measurements made on tensile test specimens, and has since been substantiated by other types of measurement. The chemical analyses and mechanical properties of several nodular irons to be discussed here are given in Tables I and 11. Tensile data for iron A was obtained from a hollow cylindrical combined stress specimen of the same dimension as those used by L. F. Coffin, Jr.1 in his investigation of gray iron properties. Standard 0.505 in. solid tensile-test bars were used for irons B and C. On each specimen type, A-8 wire resistance strain gages were used—two diametrically opposing gages in the axial direction, two in the tangential or hoop direction. By subtracting elastic strains from the measured strains, the plastic strains could be calculated. By assuming that radial and tangential strains are numerically equal, a measure of permanent volume change can be obtained by summing the plastic strains. This appears to be a good assumption, since the metal either fractured, iron A, or readings were discontinued, irons B and C, long before necking took place. This calculated variation of volume increase with stress is given for irons A and B in Fig. 1. Data for iron C is almost identical with that for iron B. The volume change indicated by Fig. 1 has been substantiated by a more direct type of density measurement. A method developed by S. G. Fletcher and' Morris Cohen,' and completely described in the discussion of their article, has been used. The accuracy of specific volume measurement has been estimated as 0.00002 cu cm per gram. Essentially the method consists of weighing a sample in air and then immersed in water. Measurements were made before and after straining the material. The results shown in Table I11 were obtained by means of half-size (0.252 in. diameter, 1 in. gage length, 3/8-16 threads) tensile specimens. Initial measurements were made on the whole specimen before stressing. After stress-

Jan 1, 1955

By R. F. Mehl, C. S. Barrett, A. H. Geisler

THE studies of the mechanism of precipitation and of the resulting property changes in aluminum-silver alloys1-3 have presented some new concepts of the aging reaction-concepts that may be fundamental in establishing a complete quantitative theory of age-hardening. With both aluminum-copper and aluminum-silver alloys, thin platelike aggregates form parallel to the Widmanstätten planes of precipitation.1,4 These platelets grow in lateral dimensions and in thickness with aging time until they are thick enough to produce an X-ray diffraction line pattern. Their structure is that of a transition lattice which is coherent with the matrix, since the atomic spacings in the matrix and the precipitate are the same on each side of their common interface.2,4 The equilibrium precipitate forms later from and at the expense of the transition lattice. Since age-hardening occurs during the formation and growth of the transition lattice, the major contributor to the hardening no doubt is the stress condition in the matrix resulting from the matrix holding the precipitate in the coherent condition. The development of these stresses also appears to be responsible for an increase in the electrical resistance superimposed on the normal decrease resulting from a change in the concentration of the matrix during aging.3 The two consecutive reactions constituting the aging process are accompanied by characteristic microstructural alterations. The initial precipitation process results in the formation of a Widmanstätten figure, while the later transformation of the transition lattice to the equilibrium lattice is accompanied by a coalescence, in the case of aluminum-copper alloys,5 and by the appearance of light areas at the grain boundaries with aluminum-silver alloys showing a structural rearrangement of matrix and precipitate.3 This latter reaction is similar microscopically to the so-called "discontinuous precipitation." Possibly discontinuous precipitation is a process that often if not always follows true precipitation of a coherent lattice and during which the transformation of the coherent transition lattice to the equilibrium lattice takes place accompanied by matrix recrystallization.3 EXPERIMENTAL PROCEDURE The alloys were made using 99.97 per cent Al or distilled magnesium, with

Jan 1, 1943

By R. D. Reiswig, J. M. Dickinson

The 0s-Ir equilibrium diagram was determined. The diagram is of the simple peritectic type, with a peritectic temperature of about 2660°C. The solid miscibility gap is narrower than previously reported, the nearly vertical solvus lines occurring at about 42 and 63 wt pct 0s. Widmanstaetten figures resembling martensite in some of the two-phase alloys account for a previously suspected transformation. In view of the long history of use of such alloys, it is surprising that the 0s-Ir equilibrium diagram has not yet been completely determined. The boundaries of the miscibility gap in this system have been estimated to be between 24 and 39 wt pct 0s and 79 and 100 wt pct OS. It has been predicted3 that alloys of ruthenium, osmium, and rhenium with the fcc platinum metals should solidify peritectically in their two-phase regions. The metallographic examination of natural osmiridium alloys has been said4 to indicate, by the presence of a martensitic structure, the existence of a transformation or a phase separation. On the basis of superconducting transition temperature measurements, a 70 at. pct 0s alloy was found5 to be two-phase prior to annealing. EXPERIMENTAL The elemental components used in this work were obtained from several suppliers as sponge. The purities, stated by each supplier to be in excess of 99.8 pct, were confirmed in each case by a semiquantitative spectrographic analysis. The pure components were premelted in an inert-gas tungsten arc furnace with the evolution of some fume, crushed, and pickled for use as alloy melting stock. Upon arc melting to the final compositions, no fume evolution was observed. Because weight losses of the order of 15 mg or less were observed in preparing alloy buttons weighing 15 g, "synthetic analyses" were used in determining the compositions of the alloys. Alloys used in this investigation contained 15, 20, 33, 40, 42, 43, 45, 50, 55, 60, 63, 64, 66, 70, 79, and 80 wt pct 0s. Heat treatments of the alloy buttons and pieces thereof were performed in a previously described6 tungsten tube furnace under pressures of 105 torr or less. It was found that homogenization treatments on the specimens were essential to remove the severe coring which was present, a 3-hr treatment above 2300°C removing all the metallographi-cally visible evidence of coring. Following the various heat treatments, the specimens were "vacuum-quenched" by melting a tungsten fuse wire and allowing them to drop onto a water-cooled copper plate. In a few instances, specimens were quenched into molten tin for comparison, but no difference was apparent. Vacuum-quenched specimens cooled from 2400°C to below a red heat in less than 60 sec. Typical equilibration times varied from 3 hr above 2300°C to 88 hr near 1100°C. The utilization of successively longer equilibration times and the approach to equilibrium from both directions indicated that the times used were sufficient to give a close approach to true equilibrium. Heat-treatment temperatures were measured with a calibrated Leeds and Northrup optical pyrometer through a 0.120-in. lateral sight hole in the tungsten heater tube. It was known that the assumption of black-body conditions inside the 1-in.-diam by 10-in.-long tube was unwarranted. The empirical results of work with thermocouples and melting

Jan 1, 1964

By A. G. Spillette, R. L. Nielsen

The purpose of this paper is to further the understanding of reservoir response to hot-water injection by desuribing a two-dimensional, mathematical model of the process. Key assumptions are that no gas phase is present, and that the injected fluid reaches thermal equilibrium instantaneously with the reservoir fluids and sand. The resulting system of three partial differential equations is solved simultaneously through the use of a "leap-frog" application of standard alternating direction implicit methods for the solution of the mass-balance equations and the method of characteristics for solution of the energy-balance equation. The utility of the mathematical model is demonstrated by comparing numerical and analytic temperature distributions for hot-water bank injection and by comparing calculated with observed field behavior. Additional calculations show that hot waterfioding can recover significantly more oil than cold waterflooding, and that a hot-water bank recovers, with less energy input, nearly as much oil us continuous injection. Introduction Consistent field success with hot fluid injection processes requires good reservoir description and a thorough understanding of recovery mechanisms. The latter is fostered by a combination of well designed experimental studies and physically sound mathematical modeling. The purpose of this paper is to further the understanding of reservoir response to hot-water injection by describing a two-dimensional mathematical technique, indicating its validity, and demonstrating its utility for studying the effects of reservoir and operating parameters. Published experimental studies of hot fluid injection processes are few." Even if extensive data were available, two considerations discourage exclusive reliance on laboratory or field work. First, because of the severity of scaling requirements," laboratory results must be interpreted with care. Second, because of the one-shot nature of field experiments — injectivity/productivity tests and pilot floods—results seldom are available over the desired range of operating conditions. These factors emphasize the need for devoting attention to mathematical modeling to complement laboratory and field work. Through the use of mathematical models, scaling uncertainties can be bridged and response can be predicted for unique combinations of reservoir and operating conditions. Numerous mathematical models developed during recent years enable us to calculate temperature distributions, thermal efficiency (or conversely, fraction of heat lost), and oil recovery behavior for hot fluid injection. Ramey" and Spillette' recently have provided reviews of these methods. Most models have concentrated on predicting temperature distributions and thermal efficiency; few have been directed at predicting oil recovery.'."1° Although these techniques are useful for estimating effects of reservoir parameters and operating conditions on process performance, results are limited by the assumptions made and by the methods of coupling independently solved fluid-flow and energy-balance equations. A computer-based method is presented for predicting total reservoir response to hot-water injection that obviates most simplifying assumptions. The model simulates fluid flow and heat transfer in two dimensions within a vertical cross-section spanning the oil sand and adjacent unproductive strata. Known numerical procedures are used to solve the governing partial differential equations. The mathematical model handles the effects of reservoir heterogeneity, gravity, capillarity, relative permeability and temperature-dependent fluid properties. In addition, a wide range of operating conditions can be modeled, including hot-water followed by cold-water injection. Mathematical Description of Hot-Water Injection Key assumptions in the mathematical model for hot-water injection are that (1) no gas phase is present and (2) the injected fluid reaches thermal equilibrium instantaneously with the reservoir fluids and sand. Relative permeability and capillary pressure are assumed independent of temperature. Darcy's law for multiphase fluid flow relates the velocities of the oil and water phases to the phase pressure gradients by the following relations:

Jan 1, 1969