Search Documents

By J. K. Stanley

Knowledge of the diffusivity of carbon in the low temperature form of iron (alpha iron existing below 910°C) is at the moment of considerable interest in the study of the decomposition of austenite and martensite, the elastic after-effect,123 the magnetic after-effect4 and the decarburization of steel below 910°C. Information on the solubility of carbon in iron, and to a lesser extent its diffusion, is also important in consideration of such phenomena as blue-brittleness, temper-brittleness, "magnetic" aging, quench-aging, strain-aging, and possibly the yield point. In order to obtain more information on these subjects more fundamental knowledge is necessary. It is the purpose of this work to present data on the diffusion and solubility of carbon in the alpha iron. The high temperature form of iron (gamma; face-centered cubic) existing above 910°C is capable of dissolving relatively large amounts of carbon, up to 1.7 pet at 1130°C, while the low temperature form (alpha, body-centered cubic) existing below 910° dissolves only a limited maximum amount of less than 0.02 pet carbon at 725°C, according to data obtained here. Since the solubility of carbon in the face-centered or gamma iron is large, relatively speaking, no great analytical difficulties have been encountered in the determination of the solubility lines5 or of the diffusion of carbon.0 The limited solubility of carbon in alpha iron offers difficulties because experimental procedures and analytical methods for low carbon contents below say 0.01 pet have to be more refined than techniques used for work with gamma iron. Because of the difficulties of applying conventional methods to the determination of the diffusion of carbon in alpha iron, virtually no work has been done on this subject. However, by proper refinement of the analytical method for small amounts of carbon, the determination of the diffusion coefficient can be made readily using modified procedures. The solubility of carbon in alpha iron has been determined over a temperature range by various investigators, but the agreement among them is poor. The present investigation establishes the limits quite accurately. Information of this kind is useful in establishing the correctness of equilibrium diagrams but, more significantly, such information on maximum solubilities, especially when extended to alloyed ferrites, should be extremely important in the study of aging and related phenomena. Literature The literature existing on the diffusion, in particular, and on the solubility of carbon in alpha iron is not extensive. The data which exist are not of a high order of accuracy, much of them being in the realm of conjecture. THE DIFFUSION OF CARBON IN ALPHA IRON Whiteley7 made the qualitative ob- servation, using metallographic techniques, that the rate of diffusion of carbon at the A1 (725°C) point was very rapid and that its diffusion was still rapid at 550°C. Snoek,4 studying the magnetic aftereffect in high purity iron, arrived at the conclusion that the after-effect could be explained by the presence of small amounts of carbon diffusing under the influence of magnetostrictive strain (lattice distortion due to magnetic interaction). In later work, Snoek8 made an estimate of the ratio of carbon diffusion in alpha to its diffusion in gamma iron, and concluded that for a temperature of 910°C the ratio of Da/D? was 2600. Polder,9 basing his calculations of D on relaxation phenomena in the elastic after-effect, estimated that Da is about 1/3 of D? at 910°C (1183°K) and is about 1/12 of Dy at 727°C (1000°K). Polder's equation for the diffusion of carbon in alpha iron was calculated to be 18000 D = 5.2 X 10-4 e-RT cm2 per sec Ham10 obtained data for the diffusion and solid solubility of carbon in alpha iron at two temperatures by using one technique similar to that employed in this study. He found a D of 8.0 X 10-7 cm2 per sec at 702°C and of 2.7 X 10-7 at 648°C. THE SOLUBILITY OF CARBON IN ALPHA IRON Although pearlite is absent in steels containing 0.06 pet,11 0.05 pet,12 or 0.045 pet C,13 it appears that the carbon in these steels cannot be in solution in ferrite. The solubility of carbon at the A1 (725°C) point was first determined by Scott14 on the basis of cooling curves, and was found to be between 0.03 and 0.04 pet C. Tamura15 by interpolating between the solubility of carbon in delta iron at 1400°C and in alpha at room temperature (assuming zero solubility) ar-

Jan 1, 1950

By C. S. Yust, J. W. Smith, J. R. Walsh, R. E. Simpson

This paper presents the results of a complete reservoir studv designed to determine a sound economic program for the conservation of oil and gas in the Pickton field, Hopkins County, Texas. The Pickton field produces from the Bacon Lime with all indications of the study being that production is predominately by dissolved-gas drive. Calculations of the total ultimate recovery to be expected under primary operations indicated only 16.7 per cent of the oil originally in place would be recovered. This unusually low recovery is due to the type of drive operating and the extremely high dissolved gas-oil ratio and shrinkage. Results are presented for six plans of returning gas to the reservoir, evaluated to determine (1) comparative recoveries and economics of (a) returning gas at a constant rate by supplementing Pickton gas with extraneous gas during the early portion of the operation, and (b) conventional gas-return operations without using extraneous gas, and (2) the optimum size of compressor plant for each type of pressure maintenance. The over-all economic program considers, for either type pressure maintenance operation. a gasoline plant to process the unusually rich casinghead gas. Since pressure maintenance will disturb equities, pooling of royalties is in the case of Pickton a prerequisite to conservation of oil by this type of operation, both from an economic and legal standpoint. In the event pooling of royalties cannot be achieved, the study considers a gasoline plant to operate under a modified primary production operation which will make the conservation of gas possible. INTRODUCTION The Pickton field, located in Hopkins County, Texas. was discovered in November, 1944. by the completion of Humble's C. D. Nichols 1, in the Bacon lime of the Lower Glen Rose formation, through perforations from 7,888 to 7.896 feet. The well initially produced 50.2 API gravity oil with a gas-oil ratio of 1,350 cubic feet per barrel. Subsurface samples of the reservoir fluid obtained soon after completion of the discovery well showed that the Pickton crude is unique in that it has an extremely high dissolved gas-oil ratio and is subject to very severe shrinkage. Calculations of the future behavior of the Pickton reservoir indicated that ultimate oil recovery by primary operations would be 3,269,000 barrels, representing only 16.7 per cent of the oil in place (19,577,000 stock-tank barrels), and that recovery could be substantially increased by returning the produced gas. The cumulative production of 1,382,694 barrels on November 1: 1947, amounted to 42.3 per cent of the estimated ultimate oil recovery from primary operations. The purpose of this study is to determine and evaluate the optimum program for conservation of oil and gas in the Pick-ton field, including the desirability of conducting gas-return operations and of installing a gasoline plant. LOCATION AND DESCRIPTION Pickton Field, The Pickton field, as shown in Fig. 1, is located in southwest Hopkins County, Texas, 12.5 miles southwest of the New Hope field, 2.7 miles northeast of the Coke field, 16 miles southwest of Sulphur Springs, and 8 miles northwest of Winnsboro, Texas.

Jan 1, 1949

By C. S. Yust, J. W. Smith, J. R. Walsh, R. E. Simpson

This paper presents the results of a complete reservoir studv designed to determine a sound economic program for the conservation of oil and gas in the Pickton field, Hopkins County, Texas. The Pickton field produces from the Bacon Lime with all indications of the study being that production is predominately by dissolved-gas drive. Calculations of the total ultimate recovery to be expected under primary operations indicated only 16.7 per cent of the oil originally in place would be recovered. This unusually low recovery is due to the type of drive operating and the extremely high dissolved gas-oil ratio and shrinkage. Results are presented for six plans of returning gas to the reservoir, evaluated to determine (1) comparative recoveries and economics of (a) returning gas at a constant rate by supplementing Pickton gas with extraneous gas during the early portion of the operation, and (b) conventional gas-return operations without using extraneous gas, and (2) the optimum size of compressor plant for each type of pressure maintenance. The over-all economic program considers, for either type pressure maintenance operation. a gasoline plant to process the unusually rich casinghead gas. Since pressure maintenance will disturb equities, pooling of royalties is in the case of Pickton a prerequisite to conservation of oil by this type of operation, both from an economic and legal standpoint. In the event pooling of royalties cannot be achieved, the study considers a gasoline plant to operate under a modified primary production operation which will make the conservation of gas possible. INTRODUCTION The Pickton field, located in Hopkins County, Texas. was discovered in November, 1944. by the completion of Humble's C. D. Nichols 1, in the Bacon lime of the Lower Glen Rose formation, through perforations from 7,888 to 7.896 feet. The well initially produced 50.2 API gravity oil with a gas-oil ratio of 1,350 cubic feet per barrel. Subsurface samples of the reservoir fluid obtained soon after completion of the discovery well showed that the Pickton crude is unique in that it has an extremely high dissolved gas-oil ratio and is subject to very severe shrinkage. Calculations of the future behavior of the Pickton reservoir indicated that ultimate oil recovery by primary operations would be 3,269,000 barrels, representing only 16.7 per cent of the oil in place (19,577,000 stock-tank barrels), and that recovery could be substantially increased by returning the produced gas. The cumulative production of 1,382,694 barrels on November 1: 1947, amounted to 42.3 per cent of the estimated ultimate oil recovery from primary operations. The purpose of this study is to determine and evaluate the optimum program for conservation of oil and gas in the Pick-ton field, including the desirability of conducting gas-return operations and of installing a gasoline plant. LOCATION AND DESCRIPTION Pickton Field, The Pickton field, as shown in Fig. 1, is located in southwest Hopkins County, Texas, 12.5 miles southwest of the New Hope field, 2.7 miles northeast of the Coke field, 16 miles southwest of Sulphur Springs, and 8 miles northwest of Winnsboro, Texas.

Jan 1, 1949

By Robert T. Gdagher, Allison Butts

EDUCATIONAL trends as reflected in curricular changes are of interest and importance in engineering educa¬tion both as matters of record and as considerations for the future. The data on which the evidence of this report is based were obtained by sending questionnaires to all schools in the United States granting the undergraduate degree in mining engineering, metallurgy, or metallurgical engineering. The questionnaire had two parts, one inquiring as to the general nature of revisions made or planned, and the other asking for information on specific courses added to or dropped from the curriculum, or given more or less time than formerly. The frequency with which curricular changes are made, even in normal times, is notable. Although it was expected that the period since 1939-40 would show numerous revisions, it was somewhat surprising to find that of 62 mining or metallurgical curricula in existence in 1939-40 and reported in the present survey, 58 had been revised or are shortly to be revised, 52 having already been changed during this period. Moreover, approximately half of the mining schools that have already revised their curricula, and probably a similar proportion of the metallurgical schools, are about to make further important changes.

Jan 1, 1948

By E. Teghtsoonian, K. G. Davis

THE preparation of cobalt crystals offers problems: on cooling through 400°C a phase transformation takes place whereby the structure changes from face-centered cubic to the low temperature close-packed hexagonal form. There are a few references in the literature which describe the preparation of cobalt crystals for magnetic work1,&apos; where melt-solidification methods were used. Reasons will be given why such methods were found unsuitable for our purposes. The following techniques were tried: 1) Solid state methods. Any mechanical shaping of tensile specimens would lead to uncertainty with regard to residual strains. With this in mind, following Kaa, strain-anneal and grain growth techniques were extensively investigated. In no Case were useful single crystals obtained. The transformation boundaries, which are crystallographically similar to twin boundaries, are probably extremely stable and inhibit the grain growth. 2) Growth from the melt. Normal melt-solidification methods were tried, using recrystallised alumina crucibles, and also a osoft moldo technique in which cobalt rod was packed in alumina powder. Trouble was encountered with gas evolution on solidification of the melt, giving porosity. Some adhesion of cobalt to the alumina also took place. Only a small proportion of the runs gave single crystals. 3) Zone-refining. Much the best results have been obtained using an electron-beam floating zone refiner. The refiner, based on a design by Calverly et Al .5 had a single-turn tungsten filament. It was operated at 600 v with an emission current around 45 ma. Commercial cobalt rod 1/8 in. in diam was given one pass at a rate of zone travel normally 25 cm per hr, under a vacuum approximately 10-5mm of Hg. Over 50 pct of the runs gave long sections of single crystal. Crystals up to 2o Cm long with good uniformity of cross section and straightness have been grown in this way. Increase in the length of the molten zone resulted in higher single-crystal yields, but control of zone stability was reduced. Sub-boundaries in the zoned crystals were few, and Laue X-ray spots were sharp. The success of the method is believed to lie in two factors, namely i) the absence of crucible restraints during the transformation, and ii) extreme axiality of heat flow during cooling. The axes of the zoned crystals were clustered around the [ 1010] pole, the pole of the basal plane being at least 60 deg from the specimen axis. Crystals grown at lower rates of zone travel showed the same orientation range, Fig. 1. This orientation is similar to that for other hexagonal metals grown from the melt, which is a little surprising when the mode of formation of the hexagonal phase is considered. The preferred orientation is probably caused by anisotropy of heat conduction, i.e., that crystal which can most effectively conduct heat away from the transformation interface will be favored. Fig. 2 shows the area on a standard cubic stereo-gram in which there are no poles more than 60 deg from one of the four < 111> directions. This area

Jan 1, 1962

* Kennecott Copper Corp. gets Charles R. Cox as president on Jan. 1. Mr. Cox is resigning his position as president of Carnegie-Illinois to take the new post with Kennecott, left vacant by the death of Mr. Stannard in September. •The ECA signed a contract in December to advance X3,600,000 to Newmont Mining Corp. to aid development of lead and zinc mines in French Morocco. The funds are to be repaid in lead and zinc for the United States&apos; stockpile over a period of seven years. The mines are owned by the Societe des Mines de Zellidja, with which organization Newmont is associated. • Under the direction of John M. Brooks, Jr., general manager, the Matahambra mine in Cuba, will probably produce sufficient tonnage to make 4 million lb of copper per month during 1950. The grade is presently running between 7 and 10 pet. •S. H. Ash reports that the fatality rate per million-man-hr for the anthracite industry for 1949, through November, is 0.78. This is 15 pct better than that achieved during 1948, which was the lowest fatal injury rate in coal mining history. The first full year on record without a major disaster was recorded in 1949 (p. 34). •The Atomic Energy Commission has authorized the production of 200 lb of uranium metal for use under AEC license in non-Commission research projects. •A national survey of projected 1950 purchases of new machine tools, machine tool accessories, materials handling equipment, etc., just completed by the American Society of Tool Engineers reveals that, of the companies reporting, 80 pct state that they plan to buy either more equipment or the same amount as in 1948. • Armour Research Foundation is conducting investigations for the use of clay and shale deposits to make lightweight aggregates. The material is heated until it expands and forms material suitable for mixing with cement which it is hoped will be lighter, stronger, have better insulating qualities and will lower the cost of concrete. •In the first six months of 1949 the bituminous coal miners&apos; average hourly earnings were $1.94 -as compared with X1.392_ national average for all manufacturing. Average annual earnings of full-time employees in the bituminous coal mines in 1948 were $3387 as compared with $2809 for all industry. •LaSalle Business Bulletin reports: "year ends on a rising trend in industry and trade ... nearly record-breaking demand from almost all sources keeps business high... most indicators but little below postwar peak... forces keeping activity high arestill powerful--changes in general business conditions likely to be slow and moderate." •Office of Internal Trade of the Commerce Department requests that technical data significant to the national security which is to be sent outside of the United States be submitted to it for an official opinion on the desirability of transmitting such information. This voluntary compliance program is part of our national security control. • Blast furnace slag reduced to 12 to 16 mesh is being used for sanding track at the Mont Coal mines of Armco. The slag replaces silica sand which caused silicosis. It has proved so effective and cheap that tests are being made to use the slag for rock dusting.

Jan 1, 1950

By A. L. Mular

lnput energy-size modulus relation at small reduc-tion ratios is expressed by Et = (M, -Mt) k;. In some cases 13 is close to Schuhmann&apos;s distribution modulus a in value. Experimental results in conjunc-tion with the equation demonstrate the fact that energy input which produced fracture is not expended on unbroken starting material inside the mill at any time. Recently, schuhmann1 derived the Charles equation2 using the postulate that complex com-minution operations can be considered as a summa- tion of many comminution events. The fragments resulting from each event are assumed to follow the Gaudin-Schuhmamn distribution. In his derivation, Schuhmann implies that the size distribution of the total mass of a material is determined by the fraction of that mass actually subjected to comminution. Consider a feed to contain a volume, Vo, of uni- formly sized homogeneous material. After t seconds of grinding, let the volume of broken material be Vo - Vt where Vt is the volume of starting material not yet broken. The size distribution of the broken material is given by: where V is the cumulative volume less than size X, and k, is the size modulus of the broken material at time t. The distribution for the total volume at this

Jan 1, 1962

By C. G. Dunn, P. K. Koh

THE primary recrystallization texture in cold-rolled silicon iron, which is the matrix texture for developing the Goss texture or the cube-on-edge texture by secondary recrystallization at temperatures near 900°C,1-5,21 has not been adequately described. Thus from the present available information, it is not possible to explain satisfactorily both the grain-growth selectivity of the matrix and the often observed magnetic torque curve, which itself provides some information on the texture. Also lacking is information on the special annealing texture that develops in this material when the annealing temperature is 1200°C or higher and the rate of rise to temperature is extremely rapid. From the work of May and Turnbull5 and from unpublished work, it was known that isothermal annealing near 1200°C tends to reduce the extent of secondary recrystallization and that a much weaker cube-on-edge texture results if appreciable normal grain growth replaces secondary recrystallization. Koh and Dunn6,7 have obtained additional information on complex primary recrystallization textures from further studies made after normal grain growth. In these instances the initial textures were retained during normal grain growth. A similar result reasonably could be expected in the present study except for the presence of a grain growth ihibitor1-5,8,9.21 and its tendency to allow only a few grains to grow. However, any information on the orientations of grains in the special annealing texture, even if far from representative of the initial matrix texture, would provide useful information on the nature of the matrix texture. In the present texture study the method of Newkirk and Bruce,10 which is based on the methods of Geisler" and Schwartz, 12 is used to obtain a complete (110) pole figure of the primary recrystallization texture. The high-temperature annealing texture is determined simply from the orientations of a large number of selected grains. The kinetic nature of the process that produces the annealing texture is treated elsewhere13 and it is shown that a form of secondary recrystallization with a very high rate of nucleation occurs during rapid annealing at high temperatures. EXPERIMENTAL PROCEDURE Commercial 0.014-in. cold-rolled silicon iron strip (3.16 wt pct Si), prepared by two stages of cold rolling with an intermediate short anneal, was given a decarburizing 3-min anneal at 800°C. Me-tallographic studies indicated complete recrystallization. Short-time anneals at 900° C and at higher temperatures proved that secondary recrystallization had not begun at 800°C, in fact, the short additional anneals were still in the induction period of secondary recrystallization. A rapid rise to an annealing temperature of 1260°C (2300°F) was obtained in a BaC12and NaCl fused salt bath. The structures that resulted from anneals in the range 12- to 1000-sec duration were relatively finegrained, even though the growth was a form of exaggerated grain growth13 or secondary recrystallization with a high nucleation frequency.= Many of the grains were large enough for an X-ray study using a 5-mil X-ray beam. A transmission Laue Camera and an optical-mechanical stage for moving the grains into the X-ray beam were used. A total of 325 grains were X-rayed in this manner and the grain orientations determined. Complete (110) pole figures were obtained for the primary recrystallization texture using CoKa radiation at 30 kv in the back-reflection range, such as (220) for (110) poles, as described recently by Newkirk and Bruce.10 The low voltage serves to reduce the spurious white radiation to a minimum. A filter of 0.001-inch iron foil was located in front of the detector slit for transmission and in front of the beam slit for back reflection. A new and improved specimen holder extended the useful tilting angle range for transmission to 70 deg instead of 60 deg as previously reported.&apos; A torque magnetometer was used to obtain the magnetic torque curves for a number of l-in. diam disk specimens. RESULTS The (110) pole figure of the material after recrystallization at 800°C is shown in Fig. 1. The positions of the pole concentrations are found to be

Jan 1, 1961

By D. R. Wieland, A. N. Barron, A. R. Hendrickson

A definite relationship has been found between the reactivity of flowing hydrochloric acid and its shear rate in a carbonate fracture. Both flow velocity and fracture width affect the acid reaction rate. Laboratory studies were conducted on acid reactivity at different flow velocities through horizontal-linear fractures, using 15 per cent hydrochloric acid at 80&apos; F and approximately 1,100 psi. Fracture width varied from 0.02 to 0.20 in. These data provide a new basis from which the spending time and penetration of the acid can be estimated. Equations were derived expressing the relationship between injection rate, fracture width, acid concentration, time and fracture height, for linear and radial fracture systems. Because the penetration of the acid before spending is closely related to the extent of productivity increase resulting from an acidizing treatment, these data provide a valuable insight into some of the controlling factors that must be taken into consideration during treatment preplanning. INTRODUCTION Acidizing of carbonate reservoirs to improve production characteristics has been widely practiced since 1932. Originally, it was assumed that the acid uniformly penetrated natural formation pores and flow channels, enlarging them and thereby increasing their flow capacity. Little consideration was given to the reaction rate of the acid, or how far it would penetrate away from the wellbore into the formation, before spending. It has been shown recently&apos; that, unless fractures are present in the rock, very little penetration is attained before spending, and the benefits of the acidizing treatment are largely confined to the immediate vicinity of the well-bore. Therefore, acid treatments may be classified into two categories: (1) matrix acidizing, in which the acid flows through multiple: formation pores; and (2) fracture acidizing, in which the bulk of the acid travels through fractures in the rock, whether natural or induced. When acidizing treatments are conducted at pressures of sufficient magnitude to open and extend such fractures, it is often desirable to inject a propping agent to hold the fracture open after the treating pressure has been released, thus providing a highly conductive flow channel through the rock. In some cases where acid attack produces surface irregularities, the resulting flow passages can be sufficient to provide high conductivity without use of a propping agent. During injection, the acid dissolves the carbonate rock with which it comes in contact until it is spent. Deeper penetration of the spent acid into the formation produces no appreciable benefit (if no propping agent is used) because the unetched fracture faces will rejoin when treating pressures are released and the fracture will "heal", with negligible resultant conductivity. The spending time of the acid thus becomes important in determining how far from the wellbore the improved-conductivity zone extends. The spending time of acid after injection into carbonate rock depends on the rate at which the acid reacts with the rock. This in turn is controlled by a number of factors, as previously reported. 2-4 These include temperature, pressure, acid concentration, rock composition, injection rate and the area-volume relationship between the acid solution volume and the surface area of the formation flow channels through which it penetrates. Thus, in matrix acidizing, where an extremely large area is exposed to the acid, spending is rapid. In contrast, spending time is prolonged in open fractures, where the area-volume ratio is much lower. Thus, greatest penetration of the acid before spending will be achieved in acid-fracturing treatments where fractures are held open by hydraulic pressure. Perkins and Kern5 have presented equations for fracture-width determinations which, for hard formations such as limestone or dolomite, indicate that high injection rates and viscous fluids are required to create wide fractures. Increasing the injection rate will, in itself, produce faster reaction rates. Because this type of reaction can be considered to be first-order diffusion-controlled, &apos;-&apos; the rate of movement of fluid past the rock surface affects the thickness of the diffusion layer, in turn affecting the reaction rate. Staudt, et al,10 report the results of tests in which a rotating marble cylinder was immersed in acid, and the weight loss at different speeds determined. Such test conditions, however, are not truly indicative of the situation in a formation during an acid-fracturing treatment. This paper reports reaction-rate data obtained under

By L. B. Schmitt, N. H. Polakowski

Square bars of cold-dvawn copper, mild steel and a 2024 aluminum alloy were forced through an adjulstable gap between two hardened steel rollers by pulling or pushing. The rollers were either free to rotate or were locked in position so that conditions comparable with drawing, rolling, ad containerless extrusion could be created at will. Push or pull forces as well as roll separatirg forces were measured. Forming efficiency and coefficients of friction were determined. For- slow-rate deformation the values ot µ wrere between 0.09 and 0.14. Possibilities for further investigation are indicated. THIS work was undertaken with the aim of a) determining the principal parameters of cold drawing under simplified conditions directly, without recourse to speculative assumptions and b) comparing drawing with rolling and extrusion from the viewpoint of forces involved and deformation efficiency. Data of type a) relating forces in axially-symmet-rical drawing to die geometry. drafting schedules, material properties and lubrication conditions are abundant. Their intrinsic value is. however. limited as long as the radial die forces are unknown. On the other hand. the difficulties associated with measurement of these forces are serious as witnessed by the extreme paucity of such information."" Comparative investigations of type b) were also remarkably few and they all employed ring-shaped dies through which round bars were either drawn or pushed.2-4 Only in one case were the applied and the die splitting forces measured simultaneously.2 In order to simplify the problem, deformation under approximately biaxial conditions was adopted in the present work;. This enables both the drawing (rolling, extruding) efforts and the separating forces to be measured with reasonable ease by conventional methods. Since drawing, extrusion, and rolling can be carried out under virtually identical conditions only in a roller die. an adjustable tool of this type was constructed. The circular die profile involved a difficulty with interpreting the drawing and extrusion data. This was obviated by arbitrarily defining the angle between a contact chord and the drawing plane as the -.equivalent" die semiangle. The simplification was considered permissible since the effect of die angle was not specifically investigated. An additional conlplication was caused by the square cross section of the processed bars. This shape was selected as a compromise between the desire to have as massive as possible specimens and the capacity of the roller die. The metal was only partially restrained from spreading laterally. the flow conditions being therefore intermediate between plane stress and plane strain. On the Huber-Mises yield criterion the constrained and uni-axial yield strengths differ by up to 16 pct but the actual error due to the ignorance of the constraint factor was presumably much smaller than the maximum. In spite of these reservations it was felt that the method employed and results obtained have some merit. With certain further refinements to be indicated later, this technique can yield data perhaps more useful for checking metal forming theories than other, mostly indirect, methods. EXPERIMENTAL Materials—The metals used together with their principal mechanical properties are listed in Table I.

Jan 1, 1961

By Richard W. Lodge

Ix the crucible-method of assaying ores for silver a certain amount of litharge is essential to supply sufficient lead to collect the precious metals. The object of this paper is to point out that the use of a .large excess of litharge in the assay of some ores will give results for silver that are uneven as well as low. So far as I know, however, an excess of litharge does not affect the results obtained in the crucible-assay of ores for gold. The main reasons for using, in the crucible-assay, much more litharge than is required to give the necessary lead button are : 1, its action as a flux; 2, its action as a desulphurizer; and 3, its action as an oxidizer, especially on metals like copper and nickel, whereby they are forced into the slag as oxides and thus prevented from passing into the lead button. Hence, by the use of much litharge in the crucible-assay more-ore can often be taken than in the scorification-process, and a lead button obtained which can possibly be cupelled at once or after a single scorification. The method is specially advantageous with an ore carrying much copper or similar impurity and poor in silver, when the assayer does not wish to resort to a wet-analysis for the determination of the silver. It is well known that some ores give better results when assayed by the scorification-method, while others give better results by the crucible-method. For several years I have noticed that, when much litharge was used with certain sulphide and arsenical ores, the results were considerably lower than when the scorification-method was used. This fact was more forcibly brought out in connection with certain work carried on this year by Messrs. H. A. Frame and

Sep 1, 1907

By J. V. W. REYNDERS

IN THE remarks which I am about to make concern¬ing the safety work of the Bureau of Mines, I want first of all to disengage myself from a disposition, which is frequently in evidence, to give spectacular emphasis to the hazards of mining operations. It is of the&apos; utmost importance to the industrial welfare of our country that the enormous annual requirement of fuel be produced and be made available in our economic activities, with a minimum of distress and hardship. The safety of coal mining is a condition with which. we are all concerned in a fundamental way. And yet we should not rush to accept hastily conceived notions that laxity among employers in respect to safety measures exists to any outstanding degree. In fact in a large number of instances, the precautionary efforts of min¬ing companies, directed to the elimination of accidents are beyond all criticism, albeit the industry suffers in reputation from the carelessness of, its less effi¬cient constituents. The Bureau of Mines has been a leading influence in disseminating the doctrines of safety, in securing the cooperation of the miners themselves, and in stirring up &apos; the laggards, both among the employers and the employed. It is much to the interest of well-conducted mine operations that the industry, as a whole, observe safety regulations to the utmost.

Jan 1, 1925

By William H. Breeding

The remarks that follow are based substantially on experience covering 45 years, 80% of which has been in placer work, rather than on a review of available literature. Most commercial placers have been deposited by the action of water. The richer and more- difficult-to-mine placers are those in the headwater areas where gradients are steepest. The most lucrative placers are generally in inter- mediate areas where volumes are greater, fewer boulders are present, and gradients are from 3% to 1-1/2%. The higher volume, lower grade placers are in the lower reaches of river systems where gradients are lower. Where gold-bearing rivers have discharged into the sea, wave action can concentrate values on beaches, past and present. Most of the rich, readily accessible placers were mined by our forefathers. Current opportunities exist: (1) in remote areas where infrastructure has been absent in the past, or development has been prohibited by adverse ownership - political or commercial; (2) in deposits that could not be mined by equipment available to our forefathers; (3) in deposits unidentified by our forefathers; (4) where the-price-of-product/cost ratio is substantially better than in earlier years; or (5) a combination of those factors. When I entered the placer business in the late 1930s, and subsequently, a prevailing opinion believed that glacial deposits should be avoided as irregular in mineral content and composition, and unrewarding to explore and develop; yet an operator has been mining a fluvio-glacial deposit profitably for the past 17 years. Rich buried placer channels, of ten called paleo-channels were worked in the last century, generally by hand methods, and under conditions that would be unacceptable today. Exploration and mining equipment now available make some of these channels attractive targets. Well-known examples are in California and Australia. The formation of a commercial placer requires a source of valuable minerals. Above primary deposits, there may be eluvial deposits formed by the erosion of gangue minerals and the concentration "in situ" of valuable minerals. Down slope from these deposits are the hillside or colluvial deposits, and below them are the alluvial deposits of redeposited material. Most of the great placer fields of the world are the result of several generations of erosion and deposition. Well-known examples are in California and Colombia. Gold is a very resistant and malleable material, and gold placers may extend for 64 or 80 km (40 or 50 miles) along a river system. Platinum is less malleable, but is very resistant to disintegration. Diamonds are extremely hard, and (especially gem diamonds) may be found over great lengths of a river system. Cassiterite is less resistant to disintegration, and tin placers seldom extend over two miles without resupply from an additional source or sources of mineralizaton. Tungsten minerals are generally more friable, and within a few hundred yards of the source disintegrate to the point that they are uneconomical to recover. Rutile, ilmenite and zircon placers generally result from the weathering of massive deposits, and may be encountered over extensive areas; most are fine grained and durable. What does a geologist or mining engineer look for in placer exploration? The old adage to look for a mine near an existing mine is still valid. You need a source of valuable mineral. Then you require conditions for concentration, which means a satisfactory gradient and/or other conditions that will permit heavy minerals to settle. Nicely riffled gravel, often called a shingling of the bars, is conducive to placer formation. Coarser gravel is logically associated with coarser gold. Excessive clay and/or high stream velocities in narrow channels can carry gold far downstream and distribute it uncommercially over a large area. When material is extremely fine, in situ weathering and concentration become more important. Placers frequently occur distant from lode mines, and one must remember that in a larger watershed the exceptional floods that occur once in a hundred or a thousand years can move great quantities of material long distances. The carrying power of water is said to vary with the fifth or sixth power of its velocity. I am not ready to disagree with Waldemar Lindgren and accept that many commercial placers are substantially enriched by the chemical deposition of gold from solutions; however, I have seen crystalline gold in clayey material quite distant from known sources of primary gold that is dif-

Jan 1, 1985

By A. J. Shaler, H. Udin, J. Wulff

In the study of the sintering of meta powders, we have come to the conclusion in this laboratory that further progress requires a more basic understanding of the operating mechanisms. This is emphasized in detail by Shaler. He has shown that a knowledge of the exact value of the surface tension is imperative for a solution of the kinetics of sintering. This force plays a principal role in causing the density of compacts to increase.2 Furthermore, a knowledge of the surface tension of solids is also applicable to other aspects of physical metallurgy. C. S. Smith3 points out the relation between surface and interfacial tension and their function in determining the microstructure and resulting properties of polycrystal-line and polyphase alloys. This paper describes one group of results of an experimental program designed for the study of the surface tension in solid metals. As a by-product of this work, considerable information has been obtained on the rate and nature of the flow of a metal at temperatures approaching the melting point and under extremely low stresses, a field of mechanical behavior heretofore scarcely touched by metallurgists. The importance of this additional information to students of powder metallurgy need not be stressed. Theoretical Considerations Interfacial tension arises from the condition that an excess of energy exists at the interface between two phases. Gibbs proves that this energy is a partial function of the interfacial area; thus: ?F/?s = ? where ?F/?s is the rate of change of free energy of the system with changing surface area, at constant temperature, pressure and composition, and ? is the interfacial tension, or interfacial free energy per unit area. If one of the phases is the pure liquid or solid, and the other the vapor of the substance, ? may properly be termed "surface tension," and is a characteristic of the solid or liquid. The attempt of a body to lower its free energy by decreasing its surface gives rise to a force in the surface which is numerically equal in terms of unit length to the free energy per unit area of the surface. Thus ? may be expressed either in erg-cm-² or in dyne-cm-1. Similarly, surface tension may be determined either by a thermo-dynamic measurement of the surface energy or by a mechanical measurement of the surface force. We have chosen the latter approach. Tammann and Boehme4 determined the surface tension of gold by measuring the amount of shrinkage or extension of thin weighted foil at various temperatures and interpolating to zero strain. The method is of questionable accuracy because of the tendency of foil to form minute tears when heated under tension. Their assumption of F = 2W?, where W is the width of the foil, is unsound, as the foil can decrease its surface area by transverse as well as by longitudinal shrinkage. Although their experimentation was meticulous, the paper does not include details of the sample configuration required for recalculating ? on a correct basis, even if such a calculation were possible. In the experimental procedure chosen here, a series of small weights of increasing magnitude are suspended from a series of line copper wires of uniform cross-section. This array is brought to a temperature at which creep is appreciable under extremely small stress. If the weight overbalances the contracting force of surface tension, the wire stretches; otherwise, it shrinks. The magnitude of the strain is determined by the amount of unbalance, so a plot of strain vs. load should cross the zero strain axis at w = F?. If balance is visualized as a thermodynamic equilibrium, the critical load is readily calculated. At constant temperature, an infinitesimal change in surface energy should be equal to the work done on or by the weight: ds = wdl [A] For a cylinder, s = 2pr2 + 2prl [2] If the volume remains constant, r = vV/pl [31 s = 2vpl+2V/l [4] ds = vpv/l - 2V/l²) dl [5] Substituting [5] into [I] gives for the equilibrium load, w = ?(z/rV- 2V/12) [6] and, again expressing V in terms of r and l, w = pr?(1 - 2r/l [7] Here the end-effect term, 2r/l, is neglected for thin wires in subsequent work. Eq 7 can be confirmed by means of a stress analysis. If the x-axis is chosen along the wire, then the stress is 2pr? - w pr² pr2 [8] A cylinder of diameter dis equivalent to a sphere of radius r, insofar as radial surface tension effects are concerned.³ Thus xv = 2?/d = ?/r = sz [9] For the case of zero strain in the x direction, the strain will also be zero in the y and z directions. Since the wire is under hydrostatic stress, Eq 8 and 9 are

Jan 1, 1950

By Edwin A. Rides

HISTORICAL ORIGIN OF THE EXPORT CREDIT AGENCIES Almost since the inception of international commerce sellers, having manufactured and/or sold and shipped goods to an overseas buyer, have been obliged to accept the risk that they will not be paid for one reason or another. There are many reasons why payment may not be forthcoming, for example, the goods may be lost at sea, or rejected by the buyer or the buyer nay simply not be creditworthy. These risks were brought into sharp relief as international trading became more sophisticated and the practice of giving credit to buyers gathered momentum. Inevitably enterprises sprang up which offered same mitigation of this exposure, accepting houses and later confirming houses and banks were prepared to assure acceptable credit risks an behalf of the seller, usually by discounting trade paper, and for many years the market ticked over reasonably satisfactorily. However, after the 1914-18 War international trade was at an extremely low ebb and its inherent risks were accentuated to a point where they were often commercially unacceptable. Yet a healthy and vigorous international market was indispensable to recovery of the world economy and a number of governments, led by the United Kingdom, perceived a need to offer their exporters a comprehensive form of insurance, particularly to facilitate the extension of credit to foreign buyers. In the United Kingdom the Export Credits Guarantee Department (ECGD) was set up to encourage trade through the provision of export credit insurance. Over the ensuing years others followed suit and now most of the developed trading nations and many developing nations have similar agencies. PRESENT DAY IDLE OF THE EXPORT CREDIT AGENCIES (ECAS ) Traditionally then the BA&apos;s role was to encourage trade through the provision to exporters of insurance against the risks of non-payment by overseas buyers of their goods and services. However, during the 1970&apos;s the manufacturing industries of most of the developed nations found themselves facing severe competition for business, particularly in the developing world. As a result the more aggressive ECA&apos;s began to introduce ancillary forms of cover designed to reduce exporters&apos; risks outside of the credit field. For instance, most of the European agencies now have a form of cover against foreign exchange risks here contracts are denominated in currencies other than that of the exporter&apos;s country. Most of the agencies also provide cover to exporters against the risk of unfair calling of bid, advance payment, performance bonds etc and in certain countries, where high inflation rates were endemic, a form of cover against cost escalation. In certain circumstances it is also possible for an exporter to obtain cover against losses arising as a result of the involvency of a partner in a consortium or joint venture. These are all forms of insurance but, also during the 1970&apos;s, many of the national export credit programmes took a major step away from their original raison d&apos;etre by facilitating the provision of preferential financing terns for the acquisition of capital equipment by an overseas buyer. This new line of business quickly became an important ingredient of major export financing packages and, as we shall see later, turned out to be extremely costly for the countries providing it.

Jan 1, 1985

By G. S. Hume

RECENT developments in the Turner Valley gas and oil field, 40 mi. southwest of Calgary, Alberta, have indicated a large producing crude-oil area. Drilling be¬gan in Turner Valley in 1913 but no major developments took place until the fall of 1924, when Royalite No. 4 well at a depth of 3740 ft. in the upper part of the Paleozoic (Mississippian) limestone obtained a production - of 20,000 M cu. ft. of gas with a content of about one imperial gallon of naphtha (73° A.P.I.) per M cu. ft. This well produced as much as 600 bbl. of naphtha per day, and until abandonment in 1934 produced 911,313 bbl., which together with the gas sold was valued at about $5,000.000.

Jan 1, 1937

By M. E. Grimes

A method of predicting uranium extraction rate in underground bacterial leaching of as-blasted ore has been developed. The method is based on the hypothesis that extraction is directly proportional to the volume of a piece of ore that is penetrated by the leaching agent, and that each piece of ore, regardless of size, has been penetrated radially from the external surface to the same depth at a given leaching time. Consequently, given an initial size and assay distribution, extraction should be predictable for a given penetration. Two laboratory bacterial leaching tests under simulated stope leaching conditions were carried out for a periods of 89 and 96 weeks. On completion, the residual ore was screened and analyzed. The information so obtained was employed to provide an elapsed time base for the penetration model, from which predictions of future extraction were made. The finding of solubilized uranium trapped within apparently sol id ore pieces was unexpected. However, it is not recoverable except after crushing, and hence does not affect calculations of underground leaching .

Jan 1, 1974

By N. K. Chen, R. Maddin

THE textures of straight-rolled and of cross-rolled molybdenum were first determined with the aid of pole figures by Custers and Riemersma.&apos; These authors have shown that for straight-rolling, the main texture was (100) [0111 with a considerable spread about the rolling direction. After cross-rolling a second texture was obtained in which there was a [111] axis perpendicular to the rolling plane, possessing a rotary symmetry. Recently Semchy-shen and Timmons2 in their study of preferred orientation of arc-cast molybdenum sheet obtained similar pole figures. In these two investigations, polycrystalline materials were used. In the main, the textures of molybdenum in these cases are qualitatively consistent with rolling textures of other body-centered cubic metals, such as iron and Fe-Si alloys." In the present investigation, single crystals of molybdenum were deformed by rolling with respect to specific crystallographic planes and directions. Since the deformation textures of polycrystalline aggregates have been related intimately to the behavior of individual grains,4 a study of possible correlations of final textures with respect to the initial orientations of the single crystals might conceivably lead to a better understanding of the textures. Annealing treatments were carried out after deformation in order to study the recrystallization characteristics as well as the recrystallization texture. Rolling of Single Crystals Single crystals of molybdenum (about 1/8 in. in diarn x 1-in. long), grown by the method previously described,5 were cold-rolled without intermediate anneals. Except for specimens MR-1 and MR-2, which were rolled at random in the preliminary test in order to find a proper rate of reduction, all other specimens were carefully documented as to their respective orientation before deformation by means of X-ray Laue back-reflection methods. A stereo-graphic projection was constructed from which it was possible to determine a particular plane and direction to be considered for rolling. Parallel flat surfaces were then polished metallographically with respect to a reference scratch on the specimen which was mounted in sealing wax. These flat surfaces contained the plane chosen for rolling. After etching, a Laue back-reflection photogram was again made of one of the flat surfaces to determine the exact plane of rolling. The initial orientations of all the specimens (specified by two elements for each crystal, direction of rolling and the pole of the rolling plane) are summarized in Fig. 1. The specimens were mounted in plasticene between two hardened Si-Fe plates. The sandwich was then rolled down, keeping the direction constant in the case of straight-rolling. In cross-rolling (MR-10, MR-11, and MR-12) the sandwich was rotated 90" after each pass so that every first and third pass contained the same rolling direction. Specimens MR-14, MR-15, and MR-16 were compression-rolled following the manner of Barrett." In these cases the direction of the sandwich through the rolls was changed by 3" to 5" for each pass until the specimens were rolled to the desired reduction in thickness. It was found that if extreme care was exercised in rolling, i. e., the amount of deformation per pass was extremely small, the specimens could be rolled to a large reduction in thickness. The rate of reduction used, with a single exception of MR-1. was generally 0.001 in. per 10 passes. Thus, it took about 800 passes to reduce a specimen to a final reduction in thickness of 87 to 98 pct. The results of rolling are shown in Table I. Cold-Rolling Textures The final orientations were determined by the conventional Laue transmission method," using molybdenum radiation, with or without a zirconium filter. Pole figures were plotted from (1101 and (200) reflections in which three degrees of intensity— heavy, medium, and light—were determined visually. Three main types of textures have been observed from the deformed single crystals. These are: 1—a

Jan 1, 1954

By D. G. Swarthout, J. W. Savage, R. W. Guard

The Nb-N constitution diagvam has been examined from 1100° to 1450°C at 1 atm N2 pressure. On the basis of- our work plus that of Brauer and coworkers the stable nitvide Phases are: a) a solid solutlion, basic niobium (bcc) with nitrogen contained interstitially; NbN,, x = <0.40; b) ß NhNx,x = 0.39 to 0.45; hexagonal (W2C type) (NbzN); a =3.058A,c = 4.961 + 0.001A c) y NbNx x = 0.75 to 0.80; tetragonal (distorted NaCl type) (Nb4N3); a = 4.386A,c = 4.332 + 0.001A; d) 6 NbN,, x = 0.88 to 0.91; cubic (NaCl type); a = 4.3885 + 0.0007A; e) E NbNx x = 0.92 to 1.00; hexagonal (Tip type); a = 2.958A, c = 11.272 * 0.0015A. In addition, a metastuble transition phase 6&apos; has been observed and occurs only during the transition 6 — E. 6&apos; NbN has these distinguishing parameters: NbNx,x = 0.96; hexagonal (anti-NiAs type); a = 2.94A, c = 5 .46A. The high-temperature phase fields in the system are governed by two reactions: a) 6 + Y + E, a entectoid reaction occurring at 1270" ± 20° C; b) o + N2 = E, a 2 012 1 reaction occurring at 1370" ± 20° C. As part of a study of the electronic low-temperature. properties of transition metal nitrides, a number of specimens of niobium nitride were prepared. Preliminary observations on these specimens showed several points of disagreement with data already in the literature. It was, therefore, decided to determine the constitution diagram for the Nb-N system between 1100" and 1450°C. The objective of this research was to define the temperature and composition regions of stability of the various phases and to explain the differences among previously proposed diagrams. Review of Previous Literature. The research on the Nb-N system to 1964 has been summarized by storms.&apos; Although he does not present a phase diagram, his review covers the research on the system thoroughly. One of the earliest works on NbN is that of Ascher-mann and coworkers2 who studied the superconductivity of the cubic 6 NbN. Subsequent work by Horn and ziegler,3 Cook, Zemansky, and Boorse,1 Rögener:5 Schroder6 and sellmaier7 has qualitatively confirmed the first results on superconductivity, although their methods of preparation differed considerably. The constitution diagrams proposed for the system by Brauer and Esselborn8 and Elliott9 are shown in Fig. l(a)and (b). The diagram in l(a) has been modified by more recent results in Brauer&apos;s laboratory (private communication). Although 6&apos; is shown on this diagram, Brauer has indicated that he now believes 6&apos; to be a metastable phase in the temperature range shown. The diagram of Elliott, Fig. l(b), is based primarily on the results of Elliott and Komjathy10 on ni-trided niobium strip or rod specimens examined by X-ray diffraction and metallography. It will be noted that these proposed diagrams are in conflict with respect to the temperature and composition ranges of

Jan 1, 1968

By O. W. Simmons, L. W. Eastwood, C. M. Craighead

The results of a preliminary study of 113 ternary titanium-base alloys are described. The compositions investigated were as follows: 1. Ternary titanium-carbon alloys containing copper, silicon, vanadium, chromium, manganese, iron, or cobalt. 2. Ternary titanium-nitrogen alloys containing chromium. 3. Ternary titanium-chromium alloys containing additions of vanadium, molybdenum, tungsten, cobalt, or nickel. 4. Ternary titanium-manganese alloys containing additions of silicon, chromium, tungsten, or iron. Tensile properties, minimum bend radii, hardnesses, response to heat treatment and aging treatment, and phase relationships for these alloys were determined. THIS is the second in a series of papers describing some of the results of the exploratory work on titanium alloys being conducted at Battelle Memorial Institute for the Wright-Patterson Air Force Base. The work with the binary alloy systems has been described in a previous publication.&apos; This paper describes ternary titanium-base alloys as follows: 1. Ternary titanium-carbon alloys containing copper, silicon, vanadium, chromium, manganese, iron, or cobalt. 2. Ternary titanium-nitrogen alloys containing chromium. 3. Ternary titanium-chromium alloys containing additions of vanadium, molybdenum, tungsten, cobalt, or nickel. 4. Ternary titanium-manganese alloys containing additions of silicon, chromium, tungsten, or iron. As the preparation and fabrication of the 0.5-Ib experimental titanium alloy ingots to 14-ga sheet, as well as the methods of testing used in this work, have been described in the first paper of this series, Titanium Binary Alloys, no further discussion of these techniques will be given. Ternary Alloys Containing Carbon The following alloys of titanium, containing carbon and one other metal, were investigated: 1. 0.25 pct carbon; 1, 2.5, and 5 pct copper. 2. 0.25 pct carbon; 1, 2, and 3 pct silicon. 3. 0.25 pct carbon; 1, 2.5, and 5 pct vanadium. 4. 0.25 pct carbon; 2.5, 3.5, 5, 10, and 15 pct chromium. 5. 0.5 pct carbon; 2.5, 3.5, and 5 pct chromium. 6. 0.25 pct carbon; 1, 1.75, 2.5, 3.5, 5, 7.5, and 10 pct manganese. 7. 0.5 pct carbon; 1.75, 2.5, 3.5, 5, 7.5, and 10 pct manganese. 8. 0.25 pct carbon; 0.25, 0.5, 1, and 2 pct iron. 9. 0.25 pct carbon; 1, 2, and 3 pct cobalt.

Jan 1, 1951