Search Documents

By Robert Goodwin, Frank R. Milliken

IN September 1939, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1907 to 1919. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about 1 per cent Cu. The chief copper mineral, chalcocite, was disseminated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was probably less than 6o per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a complete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof comprised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig.1, which gives percentages of tonnage and copper content. The tonnage within the limit of the drill holes was estimated at about five million tons with an average content of 0.42 per cent Cu, 31 per cent of which (0.13 per cent) was acid-soluble. A screen analysis of the composite dump sample is shown in Table I. Flotation tests by several companies and individuals were then made, the results of [ ] which ranged from 62 to 74 per cent recovery. On the basis of these, a Zoo-ton pilot plant employing straight flotation was built and operated for a few months. Operation of this plant was unsuccessful, as no provision had been made to handle the copper-bearing solutions resulting from the water-soluble copper, a point that was overlooked in the laboratory test work. Attempts to decant the copper-bearing solution for precipitation in the usual manner ahead of flotation were not satisfactory because of low water recovery (owing to poor settling characteristics of the pulp) and contamination of the copper precipitate with unsettled slime. Low copper prices in 1931 necessitated the termination of testing. With the stimulus of higher copper prices in 1937, a review was made of metallurgical

Jan 1, 1940

By Charles Will Wright

DESPITE the war, the First Pan American Mining Congress, held in Santiago, Chile, Jan. 15-23, was attended by about 300 persons including the official delegates from sixteen of the American republics. The United States delegation consisted of Elmer Pehrson, of the U. S. Bureau of Mines; D. F. Hewett, of the U. S. Geological Survey; William H. Hobbs, of the Carnegie Foundation; and C. W. Wright, delegate of the Board of Economic Warfare and of the A.I.M.E. Mr. Wright was elected to head the delegation. Among the other members were Edward Steidle, of Pennsylvania State College and also an official A.I.M.E. delegate; John Huttl, of Engineering and Mining Journal; W. 0. Vanderburg, foreign mineral specialist from Lima, Peru; O. B. Hundley, of the American Cyanamid Co.; Horace Graham, of the Anglo-Chilean Nitrate Co.; and several officials and engineers from the Anaconda, Kennecott, and Bethlehem Steel companies' mines in Chile.

Jan 1, 1942

By John T. Crawford

Introduction Loading and hauling systems are evaluated in open pit mining for new properties, expanding existing operations, changing systems or equipment, and equipment replacement analysis. The objective of such evaluations is to determine the equipment needed to handle planned tonnages at the lowest cash flow cost. Cash flow costs are used to combine capital outlays with operating and maintenance costs. Leasing costs could be substituted for capital costs with appropriate modifications to calculation procedures. These modifications will not be covered. This chapter will describe methods of evaluating loading and hauling systems, concentrating on some of the more often raised questions concerning quantitative data. While the methods described are not the only ones in current use, they have a record of proven reliability. The shovel and haulage truck system is used In the examples because of its common use in open pit mines. In medium to large open pit mines, electric shovels and diesel-electric drive haulage trucks are normally used. The basic ideas presented in this chapter apply to all loading and hauling systems, with appropriate modifications. The process of performing a shovel and haulage truck evaluation can be time-consuming and tedious because of the quantity of data involved, but it is not particularly difficult. The examples used to Illustrate shovel and haulage truck evaluation are based on a hypothetical open pit mine operating 350 days per year producing 31 750- 000 t (35,000,000 st, 100,000 stpd) annually, of which 11 110 000 t ( 12,250,000 st, 35,000 stpd) are ore. Selection of the optimum shovel and haulage truck fleets will be shown. The principal sources of data for the examples or any other equipment evaluation are equipment manufacturers and actual operations. Whenever possible, actual operating experience should be used to verify estimates. The quantitative data presented herein are unrelated to a specific existing mining operation.

Jan 1, 1979

By Cyril Smith

ALTHOUGH not of the same importance as electrical conductivity, the capacity for conducting heat is nevertheless a very important property of metals and alloys. A knowledge of thermal conductivity is of value in selecting alloys for many purposes and in the calculation of the efficiency of apparatus which is being designed. Unfortunately, the determination of thermal conductivity is extremely slow and tedious, consequently few data have been obtained. A further reason for the lack of information is that there has long been an impression that the thermal conductivity of an alloy is directly proportional to the electrical conductivity and that it can therefore be calculated from the latter. The Wiedemann-Franz-Lorenz law of constant ratio of the two conductivities holds with a considerable degree of precision for all the pure metals, but appreciable deviations occur in certain alloys-particularly those containing nickel-and it seems difficult to predict exactly what the ratio will be. Therefore direct determinations of thermal conductivity should be made whenever the results are, needed with any accuracy. This research is intended eventually to cover all the alloys of copper that are of commercial importance, including the binary alloys of copper with zinc, tin, aluminum, nickel, silicon, manganese, cadmium and phosphorus, and the ternary alloys copper-nickel-zinc, copper-nickel-silicon, copper-manganese-silicon, copper-zinc-tin, etc. Most of these alloys are customarily used in the wrought condition and therefore were tested in the form of annealed rods. A limited number of sand castings were also obtained and examined. This paper contains a complete review of all the previous work that has been done on copper alloys, and includes a detailed description of the apparatus and method of procedure used in the present research, together with the new results obtained on the copper-zinc series, which is the only one completed at the present time. Subsequent papers describing the other alloys will contain the experimental results and discussion only.

Jan 1, 1930

By D. M. James, J. C. Martin

The results are presented of a study of the application of analytical methods to the solution of two-phase flow into single wells. Approximate analytical expressions for the pressure distribution in two-phase flow are found ;;; a number of conditions. The results obtained from the analytical solutions me found to be in good agreement with results obtained by finite difference techniques using a high speed digital computer. Mathematical solutions for four sets of boundary conditions are presented. All of these solutions are composed of a short-term transient plus a steady or quasi-steady state. The rates of decay of the short-lived transients are analyzed. It is found that the durations of the short-term transients may be characterized by a parameter defined as the time constant which can be determined from simple relations. It is shown also that if the outer radius is much greater than the radius of the well. the short term transients decay at rates which are proportional to the square of the exterior radius, and the rates of decay are only slightly dependent upon the radius ratio. Numerical solutions based on finite difference techniques are presented for a number of conditions. The numerical solutions are in good agreement with the predictions based on the theoretical analysis for small and moderate drawdowns. Examples involving large drawdowns indicate that the nonlinearities in the equations of flow do not appreciably alter the longevity of the short-term transients. In all cases the time required for the short-tern transients to disappear is predicted satisfactorily. INTRODUCTION The mechanism by which oil and gas flow into a single well is of vital interest to the petroleum industry. The fundamental equations of two-phase flow which describe this mechanism are nonlinear partial differential equations. Numerical solutions of these equations describing pressure transients have been obtained with the aid of electronic computers. Although solutions obtained in this manner take into account a large number of effects, the reduction of this information to useful generalities is difficult. One method of obtaining generalities is the use of linearized approximations of the nonlinear equations. Since it is possible to obtain explicit solutions of the linearized equation, general properties of the role of pressure in the flow mechanism may be ascertained. Results obtained from this approach are limited to some extent by the linearizing assumptions. The severity of these limitations may be evaluated by comparing solutions of the linear equation with numerical solutions of the more exact nonlinear equations of two-phase flow. In the past considerable amount of work has been devoted to studying pressure build-up using the single-phase flow theory. Unfortunate1y, most prep sure build-up tests involve multiphase flow. A small amount of work has been done studying pressure build-up where the flow is two-phase. The encouraging results of these studies suggest that useful results may be found from additional studies of not only pressure build-up, but also the rapid transients associated with placing a well on production. This paper presents the basic theory of the pressure transients associated with placing a well on production and with closing it in. The paper is concerned chiefly with two-phase compressible flow; however, the results also apply to single-phase flow. The results are based on analytical solutions of the flow equations, and they are verified by numerical solutions using finite difference techniques. Much of the previous work on compressible flow into wells has been confined to single-phase flow. Some work has been done on compressible two-phase steady state flow, and solutions of the equations of flow have been found by finite difference techniques using high-speed computers. Muskat1 presents some rather general solutions to the equations of single-phase compressible flow into wells. Much work has been done on pressure build-up in wells (see, for example, Refs. 2-6). Almost all of the work on pressure build-up concerns single-phase flow with the exception of Ref. 5 and part of Ref. 2. Some work has been done on pressure fall-off in injection wells.718 Muskat9 presents the solution of the equations for radial steady state two-phase compressible flow. Handyl0 extends Muskat's solution to obtain

By J. A. SINGMASTERN

THE New Jersey Zinc Co.'s vertical retort plants are believed to have been in continuous operation through the whole year. At Palmerton metal purer than that made from the same ore in the old plant has been produced and has been able to compete successfully with very pure electrolytic metal in die castings and other special uses where extreme purity is worth money. A new plant using this process was put in production by the Grasselli Chemical Co. at Meadowbrook, W. Va., early in the summer. It is said to be working very satisfactorily. It is understood that this plant will not produce high-grade metal. Two patents issued to Bunce and Mahler (Nos. 1,749,126 and 1,749,127) describe a method of operating the vertical retort so that practically lead-free metal can be obtained from ores containing consider- able lead. The zinc vapors and other gases leaving the reaction zone are filtered through a column of material maintained at a temperature high enough to prevent much zinc from condensing. The filtering medium is either periodically or continuously changed.

Jan 1, 1931

The primary purpose of the Institute is to advance those sciences embraced by it through interchange of knowledge This can best be done by the presentation and discussion of technical papers by its mem¬bers Short practical papers are especially welcome In any case the author should satisfy himself that his material is of a quality that will be a credit to him and to the Institute The preparation of a good paper frequently leads to a reorientation of the author's thoughts, which is extremely valuable, and pertinent dis¬cussion thereof contributes in no small way to the professional standing of the author Members are urged to submit papers presenting the results of their work Attention to the following suggestions will greatly further the prompt and efficient handling of manuscripts 1 Subjects: The subject must be within the field of the Institute Original work, the results of field, plant, laboratory or theoretical investigations, new views on old but important problems and occasion¬ally reviews of timely and important subjects of wide interest to our members may constitute the basis of a paper The mere fact that the work is original does not necessarily justify publication it must be of a substantial nature, of value to a reasonable number of our members and worthy of permanent record It is rarely desirable to subdivide the results of a single research for publication in a variety of journals Pre¬vious publication is a bar to acceptance 2 Construction : Papers should be clearly and concisely written in good English Care in this regard insures wider reading and the saving in space permits the Institute to publish more papers The terminology and units employed should be those current in the particular field An examination of Institute publications will afford useful guidance in such

Jan 1, 1937

By Mark David Rankin

This paper represents a general assessment of the primary factors driving the market for mobile offshore drilling rigs and the utility of those factors as choice variables for the offshore drilling program planner.

Jan 1, 1982

By J. B. Newsom

SAFER, cheaper, and faster sinking of mine openings seems to have been realized with the completion of a borehole 5 ½ ft. in diameter and 1208 ft. deep, in Minnesota, during 1938. Moreover, as the opening is to be used solely for ventilation, its circular cross section, smooth walls and freedom from fire hazard recommend it in comparison with the usual timbered shafts of rectilinear cross section. It should be pointed out that a drill hole sunk without the use of explosives frequently will stand open without support, whereas a shaft sunk by standard procedure using dynamite usually must be timbered because of the wall-shattering effect of explosives. The saving in maintenance resulting from the elimination of timber is obvious. The work was done by Pickands Mather & Co. at its Zenith mine, Ely, Minn. This company wanted a ventilation opening capable of delivering 50,000 cu. ft. of air per minute to the fourteenth level, 1200 ft. below the surface. While several general articles1-3 have described the method used, detailed time and performance records have not been presented before. Moreover, with a method as new as this, it is important to compare the results attained under widely varying conditions. Among the new conditions faced at Ely were some extremely hard rock, a series of vertical fractures, seepage water, and some long stretches of sound rock which, combined with excellent equipment, gave a chance to operate without unusual delays. Developments in boring large holes have generally taken the obvious course of increasing the size of the equipment, a line of attack that has resulted in putting down 3-ft. diameter holes at damsites for studying the foundations4 and in drilling ventilation openings between levels at Butte. 5 Such drills operate from the collar of the hole, and the power from the drill is transmitted to the cutting tool through drill rods or pipes. In order to keep down the volume of rock that must be ground to sludge, the cores in large-diameter drilling are made as large in diameter as possible. Their large diameter increases their weight per foot of length, which

Jan 1, 1939

By J. H. Polhems, R. B. Brackin, D. B. Grove

THE heavy media separation process plays an outstanding role in the concentration of 4000 tons of zinc ore per day at the Mascot mill of the American Zinc Co. of Tennessee. Of the total tonnage, 72 pct is treated in the heavy media separation plant to reject 56 pct of the ore as a coarse tailing, which has a ready market. Concentrates from this separation are beneficiated further by jigging and flotation. Approximately 25 pct of the total zinc concentrate production is made in the jig mill. Jig tailings are ground and pumped to the flotation circuit where the balance of the production is made. Fig. 1 shows a generalized flowsheet of the mill. The Mascot ore is a lead-free, honey-colored sphalerite in dolomitic limestone, with lesser amounts of chert and some pyrite. A mineralogical analysis is given in Table I. After 10 years of successful operation with galena medium and treatment of nearly 10,000,000 tons of ore, a decision to convert to ferrosilicon was made early in 1948 because of the increasing price of galena and consequent high operating costs. The conversion was made on Nov. 6, 1948, and the results obtained since that time have shown remarkable improvement over those made with galena. The Table I. Mineralogical Analysis of Mill Feed, Pct Calcium carbonate 49.5 Magnesium carbonate 35.2 Iron oxide and aluminum oxide 1.5 Zinc sulphide 4.5 Insoluble 9.3 100.0 Table II. Comparative Data, Galena and Ferrosilicon Ferro- Diner-Gelenaa siliconb ence Operating costs per ton milled, ct. 21.21 9.12 12.09 Medium consumption per ton milled, lb 0.80c 0.15 0.65 Reagent consumption per ton milled, lb 0.45 0.02 0.43 Tailing assay, pct Zn 0.310 0.297 0.013 Concentrate. oct Zn 12.08 10.33 1.75 Heavy medla ieparatlon recovery. pct 89.38 90.22 0.84 Mill feed rate, tons per hr 153 166 13 Heavy mesa separation feed rate. tons per hr 100 10 0 Tons milled per heavy media separation man shift 350 620 270 Mill feed to coarse tailings, pct 51.0 56.7 5.7 Lost mill time, pct 5.6 5.0 0.6 Power consumption, kw-hr per ton 2.06 1.92 0.14 a 1947. " First 6 months of 1950. c Net consumption after deducting credit for reclaimed waste galena. Consumption of new galena was 1.320 lb per ton milled. For entire life of galena operation, a credit of 40 pct of the value of the new galena added was realized from the sale of waste galena. comparisons given in this report cover the first 6 months of 1950 as representing the ferrosilicon operation, and the year 1947 as representing the galena operation. This was the last full year in which galena was used exclusively and is representative of the best work done during the 10 years of operation with this medium. After only 2 years' operating experience, with ferrosilicon and treatment of 1,807,585 tons many advantages have been revealed and are summarized in Table 11. Development Prior to the introduction of the heavy media process, all the mill feed was crushed through 5/8 in. and treated by jigging. A finished tailing assaying 0.66 pct Zn was made on rougher bull jigs, and cleaner jig tailings were ground for treatment by flotation. The first test work on the sink-and-float method of mineral beneficiation was carried out at Mascot in 1935, using a 3-ft cone and galena medium for batch tests. The following year a 6-ft cone was installed for pilot-plant work. This unit became a part of the mill circuit on March 1, 1936, and handled a gradually increasing tonnage in the next 2 years as the process developed to the point where it could treat all the + 3/8-in. material in the mill feed. Coarse jigging was then discontinued on March 1, 1939, and all coarse tailings have been made by the heavy media separation plant since that time. Feed Preparation: The original feed preparation plant consisted of a drag washer followed by two 4x10-ft Allis-Chalmers washing screens. A surge bin and two additional 5x12-ft AC washing screens were added in 1943. Use of primary and secondary washing screens was found essential to provide the cleanest possible feed for the cone and thereby avoid excessive contamination of the galena medium. Improved washing was obtained by replacing the drag washer with a 7x20-ft Allis-Chalmers scrubber, shown in Fig. 2, which has been in service since May 1944. Throughout the life of the galena operation, delivery of extremely muddy ore to the mill overloaded the medium cleaning system, and it frequently was necessary to cut off the feed and clean the medium for several hours until its normal viscosity had been re-established. The cleaning circuit

Jan 1, 1952

By W. F. Mullen, C. W. Stickler

WITH few exceptions, unit operations in the Pennsylvania slate industry in 1950 did not differ appreciably from production methods described by Behrel and Bowles2-4 several decades ago. Many traditionally picturesque but relatively inefficient hand operations continued to contribute to high operating costs in an industry in which the margin of profit, for various reasons, was admittedly low. As part of a general program in which the Pennsylvania State College has been assisting the slate industry to solve some of its problems, time and method studies were used in an effort to determine the bottlenecks of production flow. The results are as applicable to other stone industries as they are to slate. A study of the basic elements in the production of roofing slate, structural slate, and slate blackboards among selected slate producers revealed comparatively few refinements. Any marked difference in operating method was characterized largely by the available equipment, a noticeable difference in the working properties of the rock quarried by a particular company, and by either the habit thinking or ingenuity of the individual operators. With the hope that significant economies in manufacture might result, all the unit operations were broken down into elements for study and analysis. The greater part of the study encompassed those operations from the quarry rim to the finished product; however, to obtain a reasonable synthesis of time allotments per operation, several analyses of quarrying from the finish of the wire saw cut are included for reference. The complete study of quarrying made by Bowles several years ago resulted in the introduction of the wire saw into the operation; there appears to be a need for as fundamental a change in the processing of finished slate as the wire saw was in the quarrying process. Fig. 1 illustrates the flowsheet of quarried rock from the parent bed to the quarry rim with the basic elements which contribute to the difficulty of removing slate from the ground. In Pennsylvania roofing slate is produced by one of three procedures, many operations of which are quite similar. In the traditional or classical method the quarried rock is reduced by sculping and auxiliary manual treatment to workable size and then is split and dressed (trimmed to size) in the conventional shanty. Archaic as this method might appear, there are several elements that result in substantial savings over more mechanized operations. In a modified version of this method, the block is reduced by sawing and gouging preparatory to splitting and dressing in indoor stations. This method is particularly adaptable to rock which fractures unevenly by conventional sculping methods. In the third and more modern method, reduced block received from the block maker is diamond-sawed to length and finished on a production line. Fig. 2 illustrates the flow pattern in each case. In the modified and more modern plans, dressing is done on mechanically-operated trimming machines, which appreciably reduce the fatigue factor of the operator. However, it should be noted that it is advantageous for the operator to be able to control the speed of the knife to prevent breakage of certain classes of stock. In the classical plan the splitter and dresser normally act as blockmakers also and carry their eighter slabs (equivalent in thickness to eight shingles) into the shanties themselves, all of which adds to fatigue and reduced efficiency. The extremely low investment and operating expense of the classical method has undoubtedly been of paramount importance in its continuation. Production of Mill Stock The production of mill stock is accomplished by less picturesque methods than enter into the production of roofing slate but it is, in the main, relatively more efficient because of the increased use of machinery for handling and for finishing. Mill stock can be classified into two categories as far as difference in production method is concerned: structural slate and blackboards. The significant difference in operation is caused largely by the nature of the rock used for each product with the best and easiest cleaved rock being reserved for blackboards to permit the splitting of large slabs to as little as 1/2 in. in thickness. Structural stock, on the other hand, is split into panels no thinner than 11/2 in. and

Jan 1, 1952

By E. C. Wright

FOR many years the cost of making pig iron and steel in the Birmingham district has been about the lowest in the United States. The close proximity of the important raw materials such as coal, iron ore, limestone, and the large available scrap supply made it possible to assemble all of the important ingredients necessary for steel- making with only nominal costs for transportation. Both iron ore and coal were being mined in this district at one time for about $1 per ton from underground operations. At that time mining wages were low everywhere and the labor rate in the South was considerably below that of other mining districts. This situation persisted until the emergence of labor unions as an economic and political force, emigation of southern labor to northern plants, and continued growth of industry in the South in the years following the depression of 1932. Since that time union organizing of miners and steel workers throughout the nation has increased labor costs in mining and steelmaking. This influence has been felt particularly in underground mining operations since the proportion of labor cost to total cost is still high. The previous advantage in basic labor rate in the South has been almost entirely eliminated by the equalization of labor rates in basic industries by national unions. Since 1945 these influences have been especially noticeable in increasing the cost of mining coal and iron ore in the South. The northern steel districts are still being largely supplied with iron ore from the Minnesota open-pit mines and the cost of this ore has not increased nearly as much as the cost of ore obtained from underground mines in Birmingham. A similar situation exists in coal mining; the thinner seams in Alabama are not so amenable to mechanization as the northern mines and, as a result, the output per man-day in southern mines is only about three tons of coal as compared to five or six tons per man-day in the large captive mines of West Vir-

Jan 1, 1950

By Richard L. Stowe, Donnie L. Ainsworth

The static, rapid, and shock-loading response of rock is of interest to many in the field of rock mechanics. For example, the effects of loading rates on strength and stress-strain characteristics of rock are quite important in defining input loading for use in the design of underground protective installations. Response data on rock subjected to shock loading over a wide range of pressures are also vital in the field of underground nuclear testing. In addition, material response is needed in design of shock-absorbing liners. A number of investigators have reported that ultimate compressive strength of rock increases with increased rates of loading.1-6 Wuerker3 stated that modulus of elasticity, obtained from sonic determinations, increased in some rocks by a factor as high as 4.5. It appears that only a limited amount of work has been done on comparing static modulus and modulus obtained from impact testing.6 Phillips4 showed that with increased rates of loading the deformation decreased. More recent work by Atchley and Furr5 showed that when moderate-strength concrete is stressed with increased loading rates, the axial strain at failure increased. One would expect this to occur if we think in terms of purely elastic materials. For example, if E is constant and maximum strength [amax], increases, the axial strain would also increase. However, in rock testing thus far we have worked almost exclusively with nonhomogeneous and inelastic rocks. From this fact alone the increase in axial strain with increased load application is noteworthy.

Jan 1, 1972

By William P. Prof. Blake

WHEN we consider the efforts made in Europe to promote the physical and moral well-being of the working classes, the question is suggested whether in this country, where, theoretically, every man is peculiarly the arbiter of his own destiny, we may not be too prone to expect every man to take care of himself, and neglect to make those provisions for the welfare of the employed, demanded alike by enlightened economy and humanity. In the older countries, where the disproportion between capital and labor is greater, and the working classes are more dependent, their welfare largely occupies the attention of employers. The subject is involved in the problem of the just relations of capital and labor, and we are rapidly approaching the time, if we have not already reached it, when a generous paternal interest in the welfare of the employed should be more generally manifested. It is a subject which is of special importance to mine-owners and engineers in this country, especially to those located in the coal regions. My own attention has been particularly directed to it by a visit made to the Hassard collieries, a few miles from Liege, Belgium, under the direction of M. Andrimont. This celebrated engineer has established a comfortable home for the miners near the mouth of the shaft of the mine. It has been highly successful and beneficent in its results, and may to a great degree be regarded as a, model for such undertakings. It is known as "Hotel Louise," this being the name of Madame d'Andrimont, who laid the corner-stone of the building April 4th, 1871. The structure is of brick, upon three sides of a square, and

Jan 1, 1875

By William P. Blake

When we consider the efforts made in Europe to promote the physical and moral well-being of the working classes, the question is suggested whether in this country, where, theoretically, every man is peculiarly the arbiter of his own destiny, we may not be too prone to expect every man to take care of himself, and neglect to make those provisions for the welfare of the employed, demanded alike by enlightened economy and humanity. In the older countries, where the disproportion between capital and labor is greater, and the working classes are more dependent, their welfare largely occupies the attention of employers. The subject is involved in the problem of the just relations of capital and labor, and we are rapidly approaching the time, if we have not already reached it, when a generous paternal interest in the welfare of the employed should be more generally manifested. It is a subject which is of special importance to mine-owners and engineers in this country, especially to those located in the coal regions. My own attention has been particularly directed to it by a visit made to the Hassard collieries, a few miles from Liège, Belgium, under the direction of M. Andrimont. This celebrated engineer has established a comfortable home for the miners near the mouth of the shaft of the mine. It has been highly successful and beneficent in its results, and may to a great degree be regarded as a model for such undertakings. It is known as ((Hotel Louise," this being the name of Madame d' Andrimont, who laid the corner-stone of the building April 4th, 1871. The structure is of brick, upon three sides of a square, and

By M. L. Holzworth, Philip R. Sperry, Paul A. Beck

INTRODUCTION THE basic work of Z. Jeffries1,2,3 has long ago established the main features of grain growth in the presence of a dispersed second phase. Working with sintered specimens of initially fine grained tungsten, to which various amounts of thoria have been added, Jeffries found that grain growth was inhabited, that is, practically prevented, up to a certain annealing temperature. When this temperature, which increased with the thoria content, was exceeded, extremely large grains developed abruptly from the fine grained matrix. Such a "coarsening temperature" was later found by Gross mann13,14 in certain types of steel, while Bain showed" that in other steels grain growth was gradual, without inhibition and abrupt coarsening. Later work16,17,18,19,21 demonstrated the connection between coarsening and aluminum additions. The viewpoint that the direct cause of inhibition and coarsening in aluminum killed steels is a fine dispersion of aluminum oxide21 appears to be held quite generally, although some doubts have been voiced even very recently.20 In steels with Ti additions the titanium carbide phase is considered responsible for the inhibition effects found.20 The coarsening temperature increases, with the titanium content. That coarsening may occur, as a result of certain heat treatments, even in low carbon rimmed sheet steel, was shown by Samuels,22 He also detected coarsening in a steel ingot of similar composition, after giving it the same heat treatment as that used by him for the sheet material, In this instance the identity of the inhibiting phase has not been determined, However, Tangerding found 23 that even the few small carbide particles, which occur in carbonyl iron, have a very marked inhibitive effect. As a result of an oxidizing anneal at 850°C, large grains begin to form at the surface of the carbonyl iron specimen, and gradually grow inward as the subsurface oxidation of the carbide particles progresses and eliminates the obstruction, The carbide particles can be removed also by annealing in hydrogen, with similar results. But if the oxidizing anneal of 10 hr at 850°C in air, is followed by annealing in hydrogen for 75 hr at the same temperature, grain growth is more spectacular; usually the whole specimen is transformed into a single crystal (approx. 1,5 cm X 5 cm). The reversed procedure, that is, hydrogen annealing followed by oxidizing annealing leads to smaller grains. Tangerding arrived at the logical conclusion that there must have been in his specimens some additional obstruction to grain growth resulting from a minor impurity, other than carbon. It seems likely that this obstruction was caused by an oxide formed during the oxidizing anneal and gradually reduced during the subsequent hydrogen-annealing. Other instances of grain growth inhibition of varying severity, associated with a dispersed second phase, have been described by several authors. Notable examples: lead with 0.06 pct Cu or Ni,24 cartridge brass with 0.12 pct Cr,25 or with up to 0.15

Jan 1, 1948

By AIME AIME

FREE competition, long the controlling ideal of domestic trade within the United States, has had the fundamental geographical advantage of functioning in the world's largest area of unrestricted commerce. Goods moved back and forth across state lines, unimpeded by customs, and industrial operations have developed rapidly to meet the expanding needs of a pioneer country richly endowed with natural resources. Fifty years ago, antitrust laws were adopted to protect the competitive private enterprise principle. It became illegal for one person to combine with another to restrain trade or commerce among the several states or with foreign nations. The original legislative measures defining this philosophy were the Sherman Act of 1890 and the Clay- ton Act passed in 1914. The development of Europe and other parts of the world was influenced by different conditions which led to a different theory of trade. Here were many small nations, with limited natural resources and a thin market, and they attempted to protect their national economy by tariff walls. International business arrangements for the purpose of diminishing the ups and downs of the more competitive system --crux of the modern cartel operations-seemed a logical device to stabilize production and guard the interests of both workers and consumers. European governments as well as European industrial interests became convinced that if com- petition could be held in bounds the danger of business depressions and un- employment could be reduced.

Jan 1, 1944

By Rush Greenslade

THE oil and gas lease is the basic contract of the oil and gas industry; it is the foundation stone upon which the producing industry, particularly, is based. As the industry is precarious and highly speculative, the foundation contract should be of the utmost integrity and certainty. But right there an anomaly exists; the oil and gas lease is the most obscure, most uncertain, doubtful contract in the realm of law today. That is a condition that must be considered when taking oil and gas leases, and when buying, selling, and holding them. It may fairly be asked why should this industry rest upon so insecure a foundation. Why should not the oil industry rest upon the contract that is the basis of all industry, the warranty deed? There are many contributing reasons, but the principal one is business expediency. The Anglo-Saxon idea of ownership of land is that every land owner owns from the center of the earth to the sky all that is above and all that is below-consequently the oil and gas are owned by the person who owns the surface. That idea is not exactly true with reference to oil and gas, for many states have adopted the doctrine that oil and gas are like wild animals; they are fugacious and migratory and belong to the man that traps them. But, except for that doctrine, we believe that oil and gas are owned by the owner of the surface, wherein we differ from the Latin-American countries where the mineral rights are owned by the government. The United States was settled largely by homesteading. The owners of land were, in the main, farmers, who did not have the means or the faith to drill for oil or gas. The operators or speculators did not want to buy the land on the mere possibility of finding oil; hence a compromise resulted by which the land owner gave the speculator or the operator what he called an oil and gas lease, or a right to go upon his land and drill for oil and gas. What is supposed to be the first oil lease placed on record reads as follows: Agreed this 4th day of July, A.D. 1853, with J. D. Angier of Cherrytree township in the county of Venango Pennsylvania that he shall repair up and keep in order the old oil springs on land in said Cherrytree township, or dig and make new springs, and the expense to be deducted out of the proceeds of the oil, and the balance, if any, to be

Jan 8, 1924

By Rush Greenslade

The oil and gas lease is the basic contract of the oil and gas industry; it is the foundation stone upon which the producing industry, particularly, is based. As the industry is precarious and highly speculative, the foundation contract should be of the utmost integrity and certainty. But right there an anomaly exists; the oil and gas lease is the most obscure, most uncertain, doubtful contract in the realm of law today. That is a condition that must be considered when taking oil and gas leases, and when buying, selling, and holding them. It may fairly be asked why should this industry rest upon so insecure a foundation. Why should not the oil industry rest upon the contract that is the basis of all industry, the warranty deed? There are many contributing reasons, but the principal one is business expediency. The Anglo-Saxon idea of ownership of land is that every land owner owns from the center of the earth to the sky—all that is above and all that is below—consequently the oil and gas are owned by the person who owns the surface. That idea is not exactly true with reference to oil and gas, for many states have adopted the doctrine that oil and gas are like wild animals; they are fugacious and migratory and belong to the man that traps them. But, except for that doctrine, we believe that oil and gas are owned by the owner of the surface, wherein we differ from the Latin-American countries where the mineral rights are owned by the government. The United States was settled largely by homesteading. The owners of land were, in the main, farmers, who did not have the means or the faith to drill for oil or gas. The operators or speculators did not want to buy the land on the mere possibility of finding oil; hence a compromise resulted by which the land owner gave the speculator or the operator what he called an oil and gas lease, or a right to go upon his land and drill for oil and gas. What is supposed to be the first oil lease placed on record reads as follows: Agreed this 4th day of July, a.d. 1853, with J. D. Angier of Cherrytree township in the county of Venango Pennsylvania that he shall repair up and keep in order the old oil springs on land in said Cherrytree township, or dig and make new springs, and the expense to be deducted out of the proceeds of the oil, and the balance, if any, to be

Jan 1, 1924

We are pleased to announce the appointment of Dr. Harrison W Craver, until recently librarian of the Carnegie Library in Pittsburgh, to be Director of the combined libraries of the American Society of Civil Engineers, the American Institute of Mining Engineers, The American Society of Mechanical Engineers, the American Institute of Electrical Engineers, and the United Engineering Society. DR. HARRISON W. CRAVER. Dr. Craver was born in Owaneco, Illinois, August 10, 1875. He was educated in the public schools of Carmi, Illinois, and Terre Haute, Indiana, and the Rose Polytechnic Institute, from which he was graduated in 1895, having specialized in industrial chemistry. The following year he spent in post-graduate chemical study with Dr. W. A. Noyes. In 1896 he became chemist to Kirkpatrick & Co., Limited, of Pittsburgh, and later to

Jan 5, 1917