Search Documents

By Thiago Pinto Wandekoken

A aciaria elétrica da Votorantim Siderurgia em Resende, possui um FEA de capacidade de 100 t, transformador de 100+20 MVa, equipado com 05 injetores convencionais de oxigênio e 03 injetores convencionais de carbono. Em função do elevado aporte de energia química e elétrica inserida no processo os painéis refrigerados, e demais equipamentos localizados em determinadas regiões do FEA, são termicamente mais solicitados e requerem maior atenção e rigor do sistema de manutenção preventiva, a fim de evitar interrupções operacionais do processo. Através da análise de dados históricos, detectou-se que a região do FEA de maior criticidade e intervenções de manutenção era o painel refrigerado P-10. As tecnologias Double Side e Protect Block foram instaladas em substituição ao painel refrigerado P-10 com o objetivo de aumentar a confiabilidade operacional do FEA, reduzir os riscos de acidentes operacionais, aumentar a disponibilidade dos equipamentos nesta posição, reduzir o número de intervenções de manutenção (preventiva e corretiva), reduzir os custos de manutenção (preventiva e corretiva) e consequentemente reduzir o power off do FEA.

Aug 16, 2017

By Ricardo Thomé da Cruz

O conhecimento sobre o comportamento do revestimento refratário dolomítico durante a etapa do refino de aço é fundamental para se atender às exigências técnicas de qualidade e o aumento da produção de aço. É particularmente importante que os mecanismos de corrosão dos refratários dolomíticos sejam bem compreendidos, principalmente, em operações de exceção, nas quais as exigências metalúrgicas causem forte dano ao revestimento, prejudicando não somente o desempenho do mesmo, mas também gerando um risco à segurança operacional. Este trabalho visa à caracterização técnica da camada protetora (coating) de silicato dicálcico (C2S), a qual se origina da reação entre as escórias silicosas e os refratários dolomíticos. As amostras de coating foram caracterizadas quanto à composição química, fases formadas e microestrutura. Estudou-se uma panela retirada de operação, por dano aos refratários, retirando-se amostras de diferentes regiões. Em duas amostras, juntamente com o C2S e o periclásio, foi observado à presença de fases à base de silicato de baixa fusibilidade como a cuspidina, indicando que o coating foi atacado por uma escória com elevado teor de fluorita.

Jul 30, 2018

By Giovani Gonçalves Ribamar

A metalurgia do pó torna-se um processo importante para obtenção de peças com geometria complexa, tornando-as cada vez mais viáveis. O objetivo desse trabalho é caracterizar e avaliar a influência da energia de mistura e tempo de mistura na microestrutura e propriedades mecânicas (dureza) da liga Fe 70% - Ni 30%, utilizadas em componentes eletrônicos e materiais estruturais de peças de motores automotivos, sendo produzidas por metalurgia do pó (MP). As ligas Fe-Ni foram misturadas a baixa e alta energia, 25 rpm e 200 rpm, respectivamente, por 2 (duas) e 4 (quatro) horas, compactadas uniaxialmente a frio com pressão de compactação de 8 toneladas e sinterizadas a 1.100ºC. Foram realizadas simulações para previsão das fases presentes através do software de simulação termodinâmica, Thermo-Calc, onde mostrou a possível existência de fases CCC e CFC. A microestrutura foi avaliada por Microscopia Eletrônica de Varredura (MEV), possibilitando a visualização da quantidade e do tamanho dos poros, bem como forma e tamanho dos grãos. Foi realizada espectroscopia de energia dispersiva (EDS) para análise química pontual e mapeamento químico.

Aug 8, 2018

By João Luis Moreira

A adequação dos insumos sólidos de matriz energética aplicada ao processo de pelotização na Samarco é realizada por moinho de rolos verticais, que consta basicamente do prato de moagem, pares de rolos que rolam sobre o mesmo e a carcaça com o separador estático na sua parte superior. Seu controle por muitos anos foi dado por controle convencional, onde a atuação era norteada por sentimento e experiência dos operadores. Esse tipo de controle é de difícil documentação e aprendizado, o que acarreta no aumento da variabilidade do processo. O trabalho traz uma alternativa de controle, por sistema otimizante, que são desenvolvidos de forma a maximizar a produção, oferecer um maior desempenho do processo, minimizar os custos com energia, mão de obra e redução da necessidade de paradas para manutenção do equipamento. O sistema otimizante utilizam para tomadas de decisão lógica fuzzy e crysp, estatística, modelos matemáticos e experiência de especialistas, onde as variáveis linguísticas descrevem as entradas de controle para planta dinâmica e as regras definem o relacionamento entre estas entradas.

Aug 16, 2017

By Cláudio Magno do Carmo, Gilmar Pinto Ribeiro, Luciney Miranda Martins

A rotina operacional e os seus processos de validação e acompanhamento já estão consolidados no ambiente da Tecnologia da Informação (TI). No ambiente da Tecnologia de Automação (TA) estamos avançando lentamente, apesar da grande semelhança em vários processos, devido a dificuldades de adaptação dos controles principalmente no tocante aos tempos de resposta e atuação das equipes. Enquanto a TI atua na garantia da execução do tripé formado por confidencialidade (segurança), integridade (precisão dos dados) e disponibilidade, rigorosamente nessa sequência de prioridades (CID) [1], a TA procura atender às necessidades da produção, e inverte a prioridade para a disponibilidade (DIC). Daí o conflito inicial entre os modelos: demanda imediata ou planejamento detalhado das atividades dentro dos padrões de qualidade da TI, entretanto sem impactar nas metas operacionais. É tudo uma questão de visão e principalmente de gestão por processos! Quais as diretrizes comuns? Quais os processos similares? Encontrar os pontos de afinidade, alinhados com as expectativas dos gestores e com foco na disponibilidade, sem perder a integridade e confiabilidade dos dados é o desafio.

Oct 1, 2019

By Antonio Carlos Aguiar Gagno Junior

Este trabalho tem como objetivo mostrar a plataforma de integração de dados de inspeção preditiva e sensitiva desenvolvida na ArcelorMittal Tubarão para controle da condição dos ativos, com foco em ganho de produtividade, confiabilidade, e de eficácia das avaliações. O trabalho se constitui no desenvolvimento um sistema informatizado que integre e disponibilize dados em uma plataforma única, a partir de dados migrados dos diversos sistemas específicos já existentes na ArcelorMittal Tubarão, como é o caso do sistema de controle de vibrações, lubrificantes, termografia, grandezas elétricas, além dos dados de inspeção sensitiva. O sistema visa integrar os dados dos ativos das unidades operacionais da ArcelorMittal Tubarão que tenham variáveis de controle, possibilitando a correlação entre estas variáveis de condição e também com as variáveis de processo. A integração dos dados auxilia as equipes de manutenção na detecção imediata e direta das condições operacionais dos ativos, bem como permite avaliar antecipadamente a sua probabilidade de falhas. O sistema também permite construir uma base de dados consistente, que será um pilar importante para desenvolvimento de sistema de auxílio na tomada de decisão.

Oct 30, 2017

By Neussias Inocêncio Henrique

O processo de coqueificação em uma Coqueria do tipo Heat Recovery ocorre pela queima da matéria volátil presente no carvão, principal combustível para aquecimento dos fornos. Uma segunda queima não desejada ocorre pela combustão do coque. Essa queima indesejada é denominada Burn Loss. A quantidade de ar succionada para dentro dos fornos é pelo sistema de exaustão e controlada por um sistema automático de abrir ou fechava as válvulas utilizando através de um sistema de controle chamado de PID Combustão. Com os dados do perfil de oxigênio dos fornos do tipo Heat Recovery é possível determinar a quantidade exata de O2 em excesso objetivando a queima dos gases total dos gases. Os principais benefícios de se analisar a quantidade de O2 em excesso e entender o processo de combustão dos fornos e poder alterar o sistema de admissão de ar com o objetivo de aumenta da capacidade de produção do forno (aumento da velocidade de coqueificação) e otimização da sucção ao longo dos fornos no mesmo coletor.

Oct 30, 2017

By José de Camargo

Em janeiro de 2016 a Russula foi contratada pela Dojran Steel (Sidenor) para a reformulação de sua planta de Nikolic / Macedônia. O fornecimento incluiu um novo laminador de barras e perfis com capacidade para atingir 350.000 toneladas por ano, composto de equipamento mecânico, sistema de automação, bem como todo o suporte técnico necessário para a Dojran Steel expandir sua antiga gama de produtos e melhorar sua qualidade de produto acabado. Ao final da reformulação, executada em várias fases, o novo laminador adquiriu capacidade para produzir toda gama de produtos desejada: - Redondos de 8 a 40 mm, - Barras chatas de 16 x 4 a 140 x 20mm, - Quadrados de 8 a 40 mm, - Cantoneiras de abas iguais de 20 x 20 x 2,5 a 120 x 120 x 12mm,- Cantoneiras de abas desiguais de 30 x 20 x 3 a 120 x 80 x 10,- Perfil U (UPN) com altura de 30 a 140 mm,- Perfil I (IPE) de 80 a 120 mm e - Perfil T de 20 a 50 mm.

Oct 30, 2017

By Ananda Moreira Vaz Ourique de Avila

Ferritic stainless steels have been used in the making of high and intermediate temperature operation solid oxide fuel cells (SOFC) interconnects, replacing the ceramic materials. However, at high temperatures, on the order of 700-850 0C, these steels can present significant oxidation and degradation processes, promoting increased electrical resistivity and corrosion losses that result in contamination of the electrodes and reducing the performance and the useful life of the SOFC. Thus, the knowledge on kinetics of oxidation/corrosion of these steels and their relationship with the microstructural transformations are of great importance. In this study, samples of ferritic stainless steels AISI 430, AISI 441 and Crofer22APU® were tested for oxidation at high temperature (800 0C) for long periods of time (up to 3,600 hours) and mass gains were monitored allowing the determination of the oxidation behaviors of these steels. Additionally, the microstructural characteristics of the samples before aging (corrosion-oxidation test) and after various oxidation times were evaluated by optical (OM) and scanning electron microscopy (SEM), as well as by micro chemical elemental analysis (EDS) and X-ray diffraction (XRD) phase analysis. Electrical characterization allowed determination of electrical area-specific resistances (ASR) characteristics of the systems studied, thus relating the electrical and oxidative behaviors of steels evaluated.

Aug 7, 2018

By Washington Martins da Silva Júnior

In stamping process, sliding between metal sheet and forming tool leads to wear of tool surface. Maintenance of stamping tools involves polishing the tool edge, or, in case of severe damage, replacement of the tool. Hard coatings have been applied on the stamping tool surfaces in order to reduce the maintenance cost causing a great economic impact in metal work industry. In this work, CrAlSiN coatings were applied by PVD onto SRV2W tool steel. The coating toughness was avaliated by the critical load in scratch tests. The following coating parameters were analyzed: 1- substrate surface finishing process; 2- coating architecture (multilayer or gradient); 3- chemical composition of the coating. AlSi concentration varied from the substrate/coating interface to the surface. Coatings were 3 µm thick. Scratch tests were carried out using a Vickers indenter. The applied normal load was varied from 0 to 13 N for a scratch length of 5 mm. In order to study the effect in the toughness, the substrate roughness was controlled by the finishing process before PVD coating. Samples subjected to polishing presented highest critical loads. Gradient coatings presented higher critical loads than those with a multilayer architecture. Coatings with higher concentration of AlSi near the surface supported higher loads before failure.

Jul 31, 2018

By Nicolás Ariel Zabala

During the make-up and break-out of the connections, threaded joints are exposed to intense mechanical and tribological solicitations. The connection performance is influenced by its geometry, material properties, surface treatments and thread compound. The aim of this work is to evaluate and characterize the tribological behavior of different thread compounds applied on manganese phosphated carbon steel under low speed and high pressure sliding contact. Four thread compounds were evaluated: one containing lead, zinc and graphite; other lead-free, containing copper and finally, the last two lead-free and containing non-metallic solids. The tribological behavior was analyzed by a block-on-ring tribotest. During the test, load varied linearly between 250 N and 7000 N; loading and unloading lasted 14 sec and were performed in opposite directions of rotation to simulate the make-up and break-out operations. Friction force and load as a function of time were registered. Upon completion of the test, wear surfaces were analyzed by SEM, optical microscopy and energy dispersive spectroscopy. The obtained results show that the lead and zinc containing thread compound displayed the best behavior, showing a wear reduction of approximately 20%. These results are in line with previously known oilfield experience. Average COF values around 0.15 were measured and no significant differences between dopes were observed; indicating that the wear behavior was influenced by the additive package.

Jul 31, 2018

By Humberto Tronconi Coelho

The use of friction dampers are wide proposed for a variety of mechanical systems for which it is not possible to apply viscoelastic materials, fluid based dampers or others viscous dampers. An important example is the application of friction dampers in aircraft engines to reduce the blades vibration amplitudes. In most cases, friction dampers have been studied in a passive way, however, a significant improvement can be achieved by controlling the normal force in the contact region. The aim of this paper is to study four control strategies for friction dampers based on three different hysteresis cycles. The first control strategy maximizes the energy removal in each harmonic oscillation cycle, by calculating the optimum normal force based on the last displacement peak. The second control strategy combines the first one with the maximum energy removal strategy used in the smart spring devices. Finally, is presented the strategy which homogenously modulates the friction force. Numerical studies were performed with these four strategies defining the performance metrics. The best control strategy was applied experimentally. The experimental test rig was fully identified and its parameters were used for numerical simulations. The obtained results have shown the good performance for the friction damper and selected strategy, also, the agreement between numerical and experimental results.

Jul 31, 2018

By Piotr Pajaczkowski

Hydro generators installed in Itaipu Binacional power plant with 824/737 MVA rated output power (50/60 Hz) belong to the largest ones in the world. Among many unique features the generators are equipped with the largest hydrodynamic thrust bearings ever built (external diameter 5200 mm, axial load equals approximately 3600 t). This paper is an attempt to propose a new thrust bearing design with the use of the state-of-the-art technologies and simulation techniques that demonstrate a reduction of friction power losses generated by the thrust bearing. This paper is divided into two parts. Within the first one the original thrust bearing design which was implemented in the generators is described. Related calculation results based on a thermo-elasto-hydrodynamic (TEHD) calculation software used by Alstom will be presented. A comparison between measurement results gathered in the 1980’s is given. In the second part a potential solution of a more beneficial bearing design is described. The proposed thrust bearing design modification is an implementation of Alstom’s PolypadTM coating. This modern polymer (PEEK) coating material has already been used by Alstom in projects around the world for many years. This coating allows pushing the operating parameters limits toward higher temperatures and lower oil film thicknesses far beyond the limits known for the conventional bearing materials.

Jul 31, 2018

By Rodrigo Perito Cardoso

Low-temperature nitriding of stainless steels is applied to obtain wear resistant surfaces without losing its corrosion resistance. The treatment consists in introducing nitrogen into the steel surface avoiding chromium nitride precipitation. The corrosion resistance of martensitic stainless steels is expected to be improved if the treatment parameters are correctly selected. It can be related to ?Fe2-3N and a'N phase formation on the treated surface. In the present work the influence of the pretreatment and treatment temperature on corrosion resistance of plasma nitrided AISI 420 steel samples is studied. Annealed, as-quenched and 400ºC-tempered samples were nitrided at 300, 350, 400, 450 and 500°C, for 6 h at 600 V. The pressure was 3 Torr and the gas mixture was composed of 70%N2, 20%H2 and 10%Ar, at a gas flow rate of 3.34×106 Nm3s-1. Plasma was generated using a square-wave pulsed DC power supply and the sample temperature was controlled by the duty cycle. The modified layers were characterized by optical microscopy, X-ray diffraction and microhardness measurement. The corrosion resistance was studied by electrochemical characterization, by means of Open circuit potential and Anodic polarization curves. The maximum surface hardness was achieved at 400°C. This temperature seems to be near the limit temperature for low-temperature treatment aiming to improve or at least to keep unaltered the corrosion resistance in relation to that verified for non-treated steel samples. Results confirm that the pretreatment and treatment temperature significantly affects the corrosion resistance of the treated surface.

Aug 8, 2018

By Dilermando Nagle Travessa

High strength-light weight materials are very attractive for the transportation sector, particularly to the aerospace industry. High strength-age hardenable aluminium alloys are widely used in airframes due to their unique combination of strength, density, toughness, corrosion resistance, cost and easy processing. However, the hardening capacity of such alloys is somehow saturated due to thermodynamic issues related to the conventional processing. The production of aluminum-matrix composites is a promising strategy to overcome this limitation, resulting in strength levels that cannot be reached by actual commercial aluminum alloys. In the present work, multiwall carbon nanotubes were used to reinforce the AA6061 aluminium alloy. 1 and 2% weight percent of MWCNT were mixed to the alloy powder by high-energy ball-milling process. The blended powder was consolidated by hot extrusion. The obtained composite bars were submitted to heat treatment for the T6 condition in order to combine both CNT dispersion and precipitation hardening effects. Optical and scanning electron microscopy, as well as hardeness testing, was used to characterize the bars. Typical wrought microstructure, free of defects, was observed on the extruded bars. Hardness of the composites was observed to increase by 20, 28 and 68% for 1% MWCNT 6 h milling, 2% MWCNT 6 h milling and 2% MWCNT 10 h milling, respectively, in the as-extruded condition. The better performance for the composites blended at higher milling time was attributed to a better nanotubes dispersion. Subsequent heat treatment to the T6 condition did not result in additional hardening.

Aug 8, 2018

By Eleir Mundim Bortoleto

A finite element modeling approach was developed to study adhesion phenomena during the unidirectional contact between a two-dimensional plane-strain square and a flat slab. Surfaces were metallic or ceramic, different pairs of materials were analyzed and their adhesion was considered by means of a FORTRAN subroutine (DLOAD), which was connected with commercial finite element code Abaqus and provided surface attractive forces based on the Lennard-Jones interatomic potential. Adhesive loads were considered both during approximation and separation of the surfaces. During the separation step, material transfer between surfaces, due to adhesion, was modeled by means of damage initiation and propagation at the flat slab. The parameters considered in the simulations were normal load, chemical affinity and system size and the different conditions were analyzed by comparison of the interaction forces during approach and withdrawal. This work also presents detailed descriptions of: (i) the evolution of energy dissipation due to adhesion hysteresis, (ii) the formation-growth-breakage of adhesive junctions and (iii) the evolution of stress distribution during the process. Results have indicated that chemical affinity between the bodies in contact is more relevant for adhesion than the applied load. Besides, smaller asperities are less prone to promote adhesive wear, but they may be subjected to high stress concentration effects.

Jul 31, 2018

By Gilberto Álvares da Silva

New elements have been inserted in NiTi lately, resulting in ternary alloys with specific characteristics beyond Shape Memory Effect and Superelasticity. Among all others alloying elements, the Ag additions itself gives potential antibacterial activity to that smart material. So on, the elaboration procedures of ternary NiTiAg alloys was studied in order to obtain a melting procedure to ensure further studies on this alloy. Microstructural and thermal analyses were used to evaluate the VAR-remelting production of NiTiAg with 4.0% wt silver content. The microstructure is composed by a NiTi matrix, pure Ag precipitates, and, scarcely, TiC inclusions. Heat treatments at high temperature could not dilute those Ag particles, but could lead to the precipitation of new ones. The silver element reduces the temperature of the martensitic transformation, yielding a material with superelastic behavior, beyond induces the R-phase on cooling stage of this alloy.

Aug 8, 2018

By Carlos Gonzalez-Rivera

An alternative cooling curve analysis method focused on the experimental determination of the latent heat of phase changes and phase transformation kinetics is proposed in this work. The method analyses the cooling process of a metallic sample, initially liquid that is contained into a cylindrical metallic mold, both of known weight, thermally isolated at its top and bottom. The method is based on an energy balance associated with the experimental measurement of the temperature change of the sample and the mold during their cooling process. From the numerical processing of the cooling curves, are obtained approximate values of the acting global heat transfer coefficient as a function of temperature in order to describe quantitatively the energy exchange of the metal/mold system with its surroundings. These relationships and other experimental data are used to process the cooling curve of the sample and the mold during solidification, in order to obtain the latent heat of solidification.The method was applied experimentally to zinc and tin of commercial purity, initially liquids and contained into stainless steel molds in order to determine its ability to measure the latent heat of solidification. The obtained results suggests that this method shows a good potential to characterize the solidification of metals.

Oct 30, 2017

By Levi de Oliveira Bueno

Constant stress testing was used for characterization of creep behavior of a 1Cr0.5Mo steel plate in the ex-service condition. The tests were performed on creep machines equipped with Andrade-Chalmers type profiles, high sensitivity SLVC transducer extensometry, high stability temperature controllers, and facilities for monitoring the creep curves with an automatic data logging system. Ten creep machines of this type were used in this research, in an experimental work that lasted for one year. Three temperature levels were selected: 538, 565 and 593°C, with stress in the range from 52 to 224 MPa producing rupture times varying from 5 to about 3950h. The creep curves were all followed with great scrutiny using data logger scanning rates which enabled storing thousands of readings in each case. The experimental analysis involved measurements of minimum creep rate, rupture time and final elongation at rupture. The data were analyzed according to the classical phenomenological / physical relations (Norton, Arrhenius, Zenner-Hollomon, Monkman-Grant) and also considering five traditional parameterization methodologies (Larson-Miller, Orr-Sherby-Dorn, Goldhoff-Sherby, Manson- Haferd and Manson-Succop). Comparisons are presented among the possibilities of data extrapolation from five different methodologies. Comparison is also made with creep results obtained on a similar plate of the same material in the virgin condition.

Aug 16, 2017

By Mingyu Ma, Lingling Liu, Liqing Chen, Houlong Liu

In this article, a 444-type heat-resistant ferritic stainless steel containing 0.05wt% Ce and 2wt% (Mo+W) was used as an experimental material and a study was carried out on the effect of rolling processes on the microstructures and texture evolution as well as on the mechanical properties and formability. The rolling processes contain hot rolling at different hot rolling finish temperatures, annealing after hot rolling, cold rolling and subsequent annealing. As for the hot rolling process, two hot rolling finish temperatures, 860 C and 770 C, were adopted, and their influence on the microstructures and mechanical properties was comparatively studied. The results showed that the microstructures after hot rolling and subsequent annealing could be refined by lowering the hot rolling finish temperature. The resultant microstructures after cold rolling and annealing were hereditarily refined. Lowering the hot rolling finish temperature can weaken the -fiber texture in hot rolled or cold rolled ferritic stainless steel strip. However, the -fiber texture was homogeneously strengthened by annealing the cold rolled ferritic stainless steel strip. Enhanced mechanical property and formability in terms of strength and average plastic strain ratio could be obtained by lowering the hot rolling finish temperature of ferritic stainless steel.

Oct 1, 2019