Search Documents

By B. Elevli

This paper deals with the selection of alternative accesses to a podiform chromite orebody in Turkey. The most important alternatives studied in a related project have been stated as a new vertical shaft and a ramp system. The comparison of these alternatives have been carried out on the basis of total investment costs, ore transport unit cost and net present value (NPV) of overall project for various depth. The results show that up to the depth of 700 m, the total investment cost and NPV favours the ramp access while unit ore transport cost make the shaft access preferable.

Jan 1, 2002

By Calvin J. Konya

Overloaded blastholes and insufficient stemming are major factors in flyrock accidents at surface metal and non-metal mines, Accurate measurement of blasthole depth, stemming height, and water depth would reduce the overload and the probability of blow-out, flyrock, excessive ground vibration, and airblast. Problems result because current measuring systems are inaccurate and often difficult to used A literature survey determined measurement techniques and blasting parameters prior to 1970. Similar data were gathered for current practices in 11 iron mines, 30 copper mines, and 92 quarries. Most operations used a cloth tape to measure borehole depth and stemming height; approximately 10% of the operations had dry blastholes. Alternate measurement techniques were evaluated and discussed. Candidate measuring techniques with best potential for improvement over the present weighted tape method are disposable tapes or string chains, automated readout tapes, modified sludge level indicators and acoustic resonance methods.

Jan 1, 1981

By Mike Tracy

This section of the Handbook deals with general principles to be evaluated in the development of a mining operation. It addresses the major issues that must be examined to fully evaluate a mining venture. Of course, one of the main topics to be evaluated is mine planning, which is covered in more detail in other sections (13, 17) of the Handbook and should be referenced in mine development projects. The topics to be discussed in this introduction include equipment and supplies, infrastructure, utilities, and project management. In any of the aspects mentioned, the current existing conditions at or near the mine site must be evaluated. This will include assessment of current use of utilities, infrastructure, housing, equipment suppliers, etc., as well as anticipated growth, both in the supply aspect of these systems as well as projected usage on these systems. After full assessment of both these aspects, an evaluation must be made as to the requirements the project will place on these items. Assessment must be made as to any up-grades required to bring the project on line, what impact the project will have on existing or expanded systems, and anticipated future growth impacts on support systems not only of the project but of other surrounding industry and urban devel-opment

Jan 1, 2008

Duty on Lead Reduced. -On December 28, the President signed H.R. 5047 which reduces the duty on unwrought lead from 3.5% ad valorem to 3% ad valorem, with a floor level of 1.0625 cents per pound, effective retroactively from January 1, 1980, through June 30, 1983. Pacific Northwest Power Bill Passed. -On December 5, the President signed S. 885 which will enable the Bonneville Power Administration to guarantee 20-year contracts to its 15 major industrial customers in exchange for higher rates. In effect, the bill will have industrial customers pay some of the costs of building additional generating facilities in the Northwest, of which thermal units are expected to be a major part. BPA supplies power to six primary aluminum producers which operate eleven plants having over 30% of the primary aluminum capacity in the United States.

Jan 1, 1980

By Chee Theng

"In 2013, Coeur Mining had more than $55 million in general and administrative (G&A) costs and less than $100 million in cash flow. This year, its G&A costs stand at $30 million, down by more than 40 percent, its all-in sustaining costs have shrunk by more than 30 percent, and its cash flow is above $200 million. To realize this, the company aggressively reduced both its corporate overhead cost and operating cost and repaid more than $300 million in debt.The more robust balance sheet meant the precious-metals producer was well positioned to reap the rewards of an upsurge in commodity prices in the early part of 2016. Its stock price soared from $1.75 in January to $15.98 in August. Although the stock price has since dropped to around $9 due to a stronger dollar and a more hawkish Federal Reserve that recently raised U.S. interest rates, shifting the opportunity-cost argument away from buying gold and silver, Coeur remains attractive to analysts in light of its prudent spending and improved fundamentals.Focus on balanced portfolioCoeur is the largest primary silver producer and one of the largest gold-producing companies in the United States and one of the largest silver companies in the world. Incorporated in 1928, the U.S.-listed company has a total of five operations: three in the United States, one in Mexico and one in Bolivia. About two-thirds of its revenue comes from the United States.The company is conscientious about having a balanced portfolio, so no single mine accounts for more than about 30 percent of its business. Being in three different jurisdictions provides further diversification, and its revenue split of about 60 percent from gold and 40 percent from silver gives it some metals mix. This year, it expects to produce about 466 t (15 million oz) of silver and 10.3 t (330,000 oz) of gold."

Feb 1, 2017

By Thomas Fraser, E. A. Holbrook

The data in this bulletin were obtained during an investigation of screening practice by the University of Illinois engineering experiment station and the United States Bureau of Mines under a cooperative agreement between them and the State of Illinois Geological Survey Division. Earlier work on this subject includes a study of the general practice of coal preparation in Illinois, made in 1914 and published in 1916/ and an investigation of Illinois coal-w.ashing methods, results of which were published in 1912 in a bulletin 2 that contained complete information on the methods then in use for sizing washed coa 1.

Jan 1, 1925

By W. D. Mcmillan

Important reserves of nickel ore occur in the Levies district in Oriente, Cuba. The area is mountainous and mostly covered by heavy vegetation. The ore bodies comprise surface tracts of nickeliferous laterite underlain with decomposed serpentine of ore grade. The Cuban Nickel Co., a wholly owned United States Government corporation, owns a plant for leaching the nickel from its ores at Nicaro, Oriente, Cuba, Between December 1943 and March 31, 1954, 5,902,225 short tons of ore was treated, with a recovery of 116,206,519 pounds of nickel (52,711 metric tons). In 1953, 1,330, 224 short tons of ore was mined and 27;"3,129 pounds of nickel produced. The Cuban Nickel Co. also owns a townsite, with the necessary facilities, mining equipment, and 11 miles of railroad. Ore for the plant has been produced from the Ocujal-San Juan claims on lends owned by the Nicaro Nickel Co., a sub¬sidiary of Freeport Sulphur Co. The Government enterprise is man-aged by the Nickel Processing Corp. The Cuban Nickel Co. has denounced mineral concessions and has purchased other claims from private owners.

Jan 1, 1955

By R. H. Bedford, F. T. Johnson

"In California the history of tin mining began in Riverside County in 1853, with the discovery of the Temescal deposit. This deposit remained the only one with a production record until recent small shipments were made from Kern and San Bernardino Counties.According to the California State Division of Mines, Temescal's total output has been about 125 tons of tin, all of which was produced in 1891 and 1892. It was idle from 1892 to 1928.An extensive but unsuccessful development campaign carried on in 1928 and 1929 by the American Tin Corp. produced only half a ton of the metal, and the property again was idle until 1943, when an attempt to resume operations proved unsuccessful. After 1929 no production is recorded from California until 1944 end 1945, when small shipments of sorted ore from Kern County returned about 2 tons of tin and 1-1/3 tons was recovered from sorted ore and concentrates from San Bernardino County. The total output of tin from California has been less than 150 tons, and less than 4 percent of this was produced in the last 50 years, in spite of numerous attempts during that period to promote tin mines,So marked a scarcity of a metal essential in war makes any occurrence interesting. When some prospects were reported to the Bureau of Mines in July 1942, in a new field 10 miles east of Gorman, they were at once examined and the preliminary exploration by the owners closely followed. Eventually one was explored by bulldozing end diamond drilling as a joint project by the Bureau of Mines and the Geological Survey.To supplement this joint project, the authors undertook independently a general survey of tin in California - a survey designed to check reported occurrences and to bring their status up to date. In this work, the 37 places described in the text and spotted on the accompanying map, (fig. 1) were visited end sampled. Although traces of tin were found in many pieces, nothing that suggested a tin mine was found anywhere, and it is difficult to base much hope for appreciable future tin production upon anything found thus far in California."

Apr 1, 1946

By Scott Rosenthal, David Gilkey, Michael McGivern, Lorri Birkenbuel, Daniel Autenrieth, Ty Murphy, Hadi Aldossari

A safety climate case study was carried out at a surface metal mine where investigators administered the Liberty Mutual Short Scale Safety Climate Survey to 365–368 miners to measure safety climate in consecutive years. Following the baseline safety climate survey in 2019, Foundations for Safety Leadership (FSL) training was conducted with 81 middle to upper management employees at the mine site. Investigators found statistically significant differences in the pre vs. posttraining FSL assessment scores of the middle to upper management employees who attended the training. The follow-up safety climate evaluation was compared to baseline scores and revealed no significant improvement. The overall baseline company safety climate score of 76.38 increased minimally to 76.50 (p-value = 0.616). Investigators also evaluated differences in safety climate between the company’s three major divisions (operations, maintenance, and administration). Both years administration had the highest mean score and operations had the lowest mean score. The authors attributed the statistically significant differences found among the three major divisions to various dissimilarities in their work environments.

Aug 13, 2021

By Marcel Vallée

Frequently, costs overruns and defaults in mining project performance result in serious problems and headaches for all project participants and impact on corporate objectives, profits and image and, occasionally, lead to project failure. As mining professional s, we should be very concerned that, in a recent World Bank paper (Weber-Fahr, 2001), geological and technical risks were considered the most important ones facing mining projects. Whenever we manage to reduce or minimize these risks, we are in better position to overcome the environment-, market-, finance- and community-related ones. The causes of this situation seem rather systemic, as a fairly long list of industry problems with new pro jects has been described in industry papers in pas t and recent years. A brief review of industry problems with mining projects will be given first, followed by a review of the basics of the current Quality Management and Continuous Improvement perspectives that have evolved from earlier quality control and quality assurance systems and policies. Particular particular attention will be given to the work of W. E. Deming. As the system approach is an essential part of such policies, it will be described succinctly. Given that poor communications and interactions among geologists, mineral processors and mining engineers/operators ca n seriously affect project efficiency and profitability, these interrelated processes with in the mining systems will be analyzed and modelled and the impacts of such situations will be described through a number of anonymous case histories and examples. A synthesis of Dr Deming's management system, includ ing his Four teen P oints and System of Profound Knowledge, will be prese nted .

May 1, 2002

By Robert Hopler

In issuing this pamphlet on stump and boulder blasting for the use of farmers, we wish to call attention to the fact that Du Pont High Explosives have been used with universal satisfaction for many years under diverse conditions, and have never failed to give satisfaction in mining, quarrying, roadmaking, blasting stumps and boulders, or for any other work where regard to economy and safety in use is the object.

Jan 1, 2008

By Scott W. Hazen

COMPREHENSIVE summary is presented of results of several years of research at the Bureau of Mines Mining Research Center at Denver on adapting and applying techniques of statistical analysis in mine and mineral-deposit sampling and in computing grade and tonnage of ore for a mineral deposit. In addition to elementary statistical theory the material presented in the bulletin includes: (1) Certain special statistical techniques that have been found useful in mining applications; (2) problems, implications, and limitations that may be encountered in applying these techniques in mine sampling and evaluation; and (3) numerous examples to demonstrate application of the theory and techniques.

Jan 1, 1967

By J. L. van Niekerk

The research project reported on represents the first comprehensive attempt to measure the vibration levels of a variety of tools and equipment in the South African mining industry to determine the effect thereof on the health of workers and operators. Although human vibration has been studied extensively internationally only one reference pertaining to the South African mining industry could be found. From studies conducted in Canada and elsewhere it was evident that rock drills do have potentially hazardous levels of vibration. The scope of the research included measurements on a broad spectrum of tools, machines and vehicles used in the South African mining industry. Both hand-arm vibration, where the majority of the vibration enter the body through the hands, and whole body vibration, where the whole body is exposed to vibration through contact by the buttocks or feet, were investigated and measured. More than 700 sets of vibration data measured on 70 machines at 15 mines and workshops were obtained. Data were obtained for at least 24 different types of equipment and machines that were previously judged to have medium to high levels of vibration. All measurements were conducted in accordance with the international standards: ISO 5349, on hand-arm vibration, and ISO 2631-1, for whole body vibration. The equipment with the highest vibration levels in the hand-arm category was: rock drills, both pneumatic and hydraulic; pavement breakers and jackhammers; hand-held compactors; pneumatic wrenches and electrical hammer drills. Of these the rock drills had weighted vibration levels in excess of 20 m/s2. As far as whole body vibration was concerned the highest values were measured on earth-moving equipment. The major conclusion from this study is that the measured vibration levels are sufficiently high to create an enhanced level of risk of vibration-induced disorders in a significant proportion of the operators of hand-held equipment. The most notable examples are hand-held rock drills, pavement breakers, jackhammers and certain selected workshop tools. The results of the study indicate that a comprehensive epidemiological study should be undertaken on present and past workers to determine the prevalence of vibration-induced disorders.

Jan 1, 2000

By Pedro Lilienfeld

This report describes a program whose objective was to develop, design, fabricate and laboratory-test two prototype instruments capable of real-time selective detection and measurement of airborne fibrous-shaped particles. The operation of this fibrous aerosol monitor (FAM) is based on the rotation imparted to the acicular particles by means of a rotating quadrupole electric field of the order of 3000 V/cm. This field induces a dipole charge separation on the fibers and aligns them with the applied field. The selective detection of the fibers is effected by synchronous detection of the resulting modulation of the light scattered from a continuous-wave helium-neon laser beam by the rotating particles. The theory of operation, design of the electric-optical detection configuration and the electronic signal processing method are discussed. By means of a scattering pulse sharpness discrimination technique, fibers whose length exceed a selectable value are detected and their number concentration digitally displayed. Counting times of 1 to 1000 minutes permit the measurement of fiber concentrations between 0.001 and about 30 cm-3. A concentration of the order of one fiber per cubic centimeter can be assessed within a relative standard deviation of 10 percent with a counting period of 10 minutes. The FAM is a portable, battery-powered instrument capable of operating continuously for about 4 hours between battery charges. Preliminary tests with crocidolite and crysotile asbestos as well as with glass fibers were performed in the laboratory and the results indicate good correlation with the standard NIOSH phase contrast microscopy filter counting method.

Jan 1, 1977

By P. V. Chandramohan

"In ports, piled berths are designed and constructed for berthing of ships with a finite draught. Piles in a bridge foundation also have a large free stand above scoured level. The piles of these structures have to withstand large horizontal forces imparted by the impact of the approaching vessels or due to longitudinal and transverse action in a bridge. It is also imperative that these piles have to project out of the dredged / scoured bed. These piles are normally designed as slender compression members subjected to bending also. They are subjected to vertical load tests for assessing the soil resistance. Lateral load tests, as a rule, are also stipulated. IS and IRC codes stipulate a deflection criteria for lateral load test to arrive at the capacity. These tests are usually conducted on a working pile by jacking out two piles. At the time of the test, pile will be free headed. But in service, piles are fixed head. There is a large difference in deflections between a fixed head and a free headed pile. Besides, a free headed pile will be subjected to a much higher bending moment than the fixed head one. This will put the working test pile under risk of breaking during the test. The problem is analyzed with case studies. INTRODUCTION Vertical capacity of piles is assessed by static formulae. This formula is based on the soil properties obtained from random soil exploration and laboratory and in-situ testing. Since soil is not a homogeneous medium, properties can vary. The design parameters taken for computations may be different from the ones at the interface of the pile with the soil. The best way is to find out is by a load test. The code IRC:78-2014 has rightly stated that initial load test is part of the design process. This is true with the vertical load test. But there are certain problems with the purpose and inference of the lateral load test. In both the tests the criteria for acceptance is the quantum of movement of the point of application of the load. In the former, the movement is vertical and depends more on the compression of the soil than the compressive strain in concrete. But in the latter, this movement is partly on account of the flexural rigidity of the pile and partly due to the horizontal compressibility of the soil. The role of rigidity of the pile is more when compressibility of the soil is higher. Lateral load test is done by jacking one pile against another because it is difficult to get an independent horizontal reaction. Please see Fig.1 Photo."

Jan 1, 2015

By LESTER W. STRAUSS

FOR fifteen months after the other dominions of the British Empire and the entire so-called sterling 11loc loosed the shackles that bound the111 to the gold standard, South Africa, giant among gold-producing nations, remained stubbornly attached to gold at the traditional ratio of 85 shillings in currency to one ounce of gold. But eventually even South Africa had to heed the dictates of trade and the obvious interests of its great gold-mining industry. In December, 1932, South Africa's currency severed its golden bonds. Today the South African pound is 011 a par wit11 the British pound.

Jan 1, 1935

By Maurice E. Peloubet

This discussion of accounting will describe the statements and the information that the accounting system produces, from the point of view of those who use such systems rather than of those who prepare them and who do the detail and technical accounting work. In any well organized mine, quarry, or other enterprise exploiting a mineral deposit, no matter how small, some clerical and accounting work must be done. Miners and other employes must be paid, supplies must be purchased and issued, and various tax and information returns, which even the smallest enterprise must file, have to be prepared. In this chapter it is assumed that the enterprise has employes of this type and that they understand the fundamentals of record keeping and accounting. It would be impossible here to give sufficiently full explanations to enable a man with no previous clerical and accounting training to set up and operate an accounting and cost system for even the simplest extractive operation. Rather, we shall hope first, to tell the investor and the operator, from the chief engineer or president down to a subforeman, what to expect from the accounting statements and records and how to use this information in his daily work; and second, that it will enable the man with some knowledge of accounting or book- keeping, but with little or no experience in any extractive industry, to set up and operate a satisfactory system for a mine or other extractive enterprise. For readers who wish to go further, the bibliography at the end of this chapter contains many references. T he emphasis has, therefore, been placed on the statements to be produced and the purposes for which they are to be used rather than the underlying books and records. These are, with a few exceptions which will be described later, essentially what might be found in any industrial enterprise and would probably, in the extremely small enterprise, consist of handwritten journals, ledgers, analysis books, payroll books, and stores ledgers. In the larger enterprise, various types of mechanical accounting would be introduced in proportion to the complexity of the operation.

Jan 1, 1964

By Ann G. Kim

Fires that occur in abandoned coal mines, waste banks, and in coal outcrops constitute a serious health, safety, and environmental hazard. Toxic fumes, the deterioration of air quality, and subsidence constitute the greatest hazards from these fires. Although tires on abandoned mined land (AML) occur in every coal-producing state, the severity of the problem varies. Methods to extinguish or control AML fires, including excavation, fire barriers, and sealing, are generally expensive and have a relatively low probability of success This U.S. Bureau of Mines report includes information from a variety of sources, i.e., agencies of the Federal Government, State agencies, research reports, conference proceedings, product information, and technical literature. This information has been collated into a comprehensive discussion of AML fire problems. Data on past fire control projects and on the estimated extent of the current problem have been compiled. Factors affecting the occurrence, propagation, and extinguishment of AML fires are discussed. Conventional fire control methods are described, and their probable effectiveness is evaluated. Information on the hazards of AML fires and safety considerations is included. The status of current technology, recent improvements in fire control methods, and areas of current research are discussed.

Jan 1, 1993

By George C. Branner

This circular is concerned with eight nonferrous scrap metals as they generated, collected, prepared, and consumed in California. Brief reference also is included with respect to Nevada and Hawaii. Four of these scrap metals - copper, lead, aluminum, and zinc - are of major importance and make up about 95 percent of the total value, whereas the remaining four - antimony, magnesium, nickel, and tin - make up the remaining 5 percent. For convenience, the subject matter is divided into three parts, (1) Data with respect to the collection, preparation, and marketing practices that are common activities to all the nonferrous scrap metals; (2) separate discussions and statistical data with respect to each of the eight nonferrous scrap metals in California; and (3) data with respect to Nevada and Hawaii.

Jan 1, 1962

By I. Benning

Since the dismal performance of the Rand Mines management was called to account by its shareholders in 1994, the waves of change have continued to ripple across the South African mining industry .The number of listings on the gold board of the Johannesburg Stock Exchange, that once numbered 40 or 50-odd, have now dwindled to no more than a handful as unprecedented restructuring has taken place. The redefining of the industry has not been limited to the gold sector, but across the base metal, coal, diamond, platinum and industrial mineral sectors as well. At the same time the Mining Houses began to reconsider their funding strategies. Originally established in the early part of the century to ensure the long-term sustainability of their group mining operations by providing substantial financial muscle and technical support, the Mining Houses were faced with a rapidly changing political environment, which proved to be a critical catalyst in giving momentum to the change. Furthermore, the significant development costs and increasing risk profile for new projects, coupled with pressure from shareholders demanding respectable returns, opened the door to opportunities for banks to begin providing external debt by the way of project finance. However, the provision of long-term debt to the South African mining industry had generally not been common since mining companies had financed new projects with equity, or with the cash flows from existing operations. Those banks that had the appetite for exposure to the perceived high risks of the mining sector rapidly built up specialist resource banking divisions capable of addressing the increasing demands of the industry. The application of project finance, the principles of which were developed in the 1970s specifically for infrastructure projects and privatization, is now commonly applied in the financing of greenfield and brownfield mining projects. This paper outlines the approach that lending banks would typically adopt when arranging or providing mining project finance, their usual areas of concern and the way in which the finance is structured to mitigate the many inherent risks.

Jan 1, 2000