Search Documents

By W. C. Peters, M. W. Pullen, C. A. Bays

During the past three and a half years considerable improvement in the techniques of solution extraction of salt has been made by the use of wells which are cross-connected by hydraulic fracture at the base of the salt. Fracture is initiated by the application of hydraulic pressure. Underreaming and perforating techniques are used to control initiation. The fracture is then extended by continuous pumping until a pressure communication is obtained. Pressure communication is followed by washing-through to obtain a low-pressure connection. Well construction using non-shrinking cements that will bond with the salt and with associated strata is essential to the process. The connecting procedure described permits solution to attack the salt deposit from its base upward, thereby permitting greater recovery, fewer well repairs, better saturation of brine, and overall economy of development and operation. The fracture method of cross-connection requires special pumping of the fluid and is limited by present experience to initial well spacings up to about 1200 feet. The method has been used in bedded salts and is applicable for wells in salt domes. Since spring of 1956, new developnents in salt extraction wells have followed procedures substantially different from those in prior use. Although multiple well systems, connected either by the natural consequence of the solution process or by undercutting under protective pads, have been used previously, the past three and a half years have brought about new designs and new operation procedures based on cross-connection of the wells using hydraulic fracture. To date these techniques have been applied largely in the bedded salt deposits of Michigan, Ontario, Ohio, West Virginia, and New York. To the writers' knowledge they have not been used in salt dome wells. The methods have not yet been in use for a sufficient period to permit any statistical comparison with the older methods. It is evident from experience to date that the methods result in higher recoveries, lower capital and operating costs, better saturation of produced brine, reduced well maintenance and repair, and in considerably fewer production units to insure

Jan 1, 1961

By D O. Hayba

Metal-rich slurries discharged from excess-enthalpy geothermal wells at Kawerau (NZ) indicate that an efficient ore precipitation mechanism operates in some feedzones. In our conceptual model, which takes into account the relative permeabilities of liquid and gas phases in boiling fluids, a metal-precipitating liquid phase is effectively immobilised along boiling fronts, leading to the formation of highly concentrated ore. Chemical equilibrium and heat/mass transport modelling demonstrate the general applicability of this conceptual model to hydrothermal eruption environments.

Jan 1, 1995

By Frank Parrish

THIS REPORT by the Federal Bureau of Mines presents data on water-supply wells used by waterflood operators in North Texas and shows the distribution of permeable source sediments. Averages of well characteristics, including static fluid levels, working fluid levels, net thicknesses, producing rates, and depths, are presented and discussed. Essentially all water used in waterflooding is mineralized water from consolidated sediments. This study is concerned with the geology and distribution of these mineralized source sediments, whereas previous work in this area was predominantly a study of shallow sources of potable water. Tables, isopachous maps, and electric-log cross sections are included to describe the several source aquifers. In general, water-producing capacity increases with depth of the sediments. Wells completed in Cretaceous sediments 82 to 600 feet deep yield 50 to 600 barrels of water daily, whereas those completed in Pennsylvanian sediments 360 to 4,110 feet deep yield 100 to 7,000 barrels daily. Although deeper formations are used where oil and water are produced conjunctively and where large withdrawal rates are required, insufficient well data prevented mapping of deeper formations.

Jan 1, 1961

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions 5/ issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1962

By K. Holmberg, D. Herriot

This paper by Mr Mclvor is yet another contribution to the eternal controversy surrounding the benefits, or otherwise, of high circulating loads in closed circuit grinding. Throughout the paper it is difficult to establish whether the author is referring to effects relating to the mill, classifier, or to the overall circuit. Table 1 is put forward as indicating the advantage of operating at high circulating loads. From the two (it would be interesting to see more) product sizing points provided in each case, the conclusions to be drawn are that cases one and two have very similar size analyses. The third case, however, indicates a much flatter curve, that is to say, higher fines production and a very wide spread of size ranges. If the objective of this circuit is to provide a closely sized product with minimum overground slimes to the downstream process, then it would appear to be the less "efficient" by far. No data is given for product pulp densities either. The term "efficiency" should never be used without a careful and clear definition. In this case, "efficiency" is used to express an apparent percentage reduction in operating work index (Bond) from the measured "standard" at 250% circulat¬ing load operation. The Bond calculation is itself based upon

Jan 1, 1989

By George S. Rice

In response to numerous requests for information as to the status of internal-combustion mine locomotives of the Diesel type that use heavy or non- volatile oil for fuel, with special reference to their safe use in coal mines, the United States Bureau of Mines is issuing this report. Data mere obtained, on application of such locomotives to cod mining only in Belgium, France, Germany, and Great Britain. The locomotives are used in coal mining in other countries, as well as in potash, iron, and other kinds of mining, but their chief development has been in coal mining in Germany, France, and Belgium. Recently popular interest in the Diesel type of engine for motive purposes was aroused in this country by the successful application of Diesel engines to railroad locomotives hauling fast transcontinental trains, and, according to published statements, at a low cost of fuel per mile of run.

Jan 1, 1936

By M. Feely, W. G. O'Keefe, C. O'Reilly, M. P. Holdstock

A petrographic and microthermometric study of fluid inclusions in the Kentstown Granite, crosscutting quartz (VI) and calcite+quartz (V 2) veins in the granite and calcite+quartz (V 2) veins in the overlying sediments was performed on samples taken from the borehole. Comparisons of the type 1, type 2 and type 3 fluid inclusion populations recorded in the present study with those from other Irish Caledonian granites strongly suggest a similar fluid evolutionary history. Furthermore, the low-temperature CaC12-rich brines (type 5) of this study, which must be syn- to post-Lower Carboniferous in age, have correlatives both in Irish Caledonian granites and in the Lower Carboniferous base-metal deposits of the Irish midlands

Jun 19, 1905

By The Staff

Introduction It is the purpose of this paper to discuss a number of the metallurgical improvements in the technology of copper-nickel ore treatment which have been introduced during recent years in the plants of ?the International Nickel Company of Canada, Limited. In common with other ore treatment processes, the procedure for extracting nickel and copper is changing almost continuous! y. These changes are necessitated by reason of changes in ore grades and characteristics, rising material and labour charges, and the constant drive to maximize metal recovery and to minimize production costs. It is not possible to present a comprehensive list of all the changes made, and only a selected number of the improvements in the milling, smelting, and refining operations are covered. It should be clearly understood that some phases of the procedures described have been pioneered by others in kindred fields and due acknowledgment is given to their foresight and efforts. Articles have been published over the years describing the operations of the International Nickel Company plants and the reader is referred to the Engineering and Mining Journal, Vol. 130, No. 9, November 10th, 1930, and to the Canadian Mining Journal, Vol. 58, No. 11, November, 1937, and Vol. 67, No. 5, May, 1946. Other references are the Transactions of this Institute, 1932, 1938, and 1946; Metals Technology, American Institute of Mining and Metallurgical Engineers, February, 1938, and Canadian Chemistry and Process Industries, April, 1940.

Jan 1, 1948

By AIME AIME

LOCAL COMMITTEES. GENERAL RECEPTION COMMITTEE.-Mr. and Mrs. H. S. Chamberlain, Mr. and Mrs. J. T. Lupton, Mr. and Mrs. T. H Lasley, Mr. and Mrs. R. S. Faxon, Mr. and Mrs. H. Clay Evans, Mr. and Mrs. C. E. James, Mr. and Mrs. B. F. Thomas, Air. and Mrs. H. S. Probasco, Mr. and Mrs. W. M. Lasley, Mr. and Mrs. L. W. Llewellyn, Mr. and Airs. T. G. Montague, Mr. and Mrs. E. B. Thomasson, Mr. and Mrs. C. F. Milburn, Mr. and Mrs. C. A. Raht, Mr. and Mrs. C. C. Notting¬ham, Mr. and Airs. Z. C. Patten, Mr. and Mrs. Willard Warner, Mr. and Mrs. S. R. Read, Mr. and Mrs. Carl White, Mr. and Mrs. M. M. Allison, Air. and Mrs. C. E. Buck, Mr. and Airs. H. F. Temple, Air. and Mrs. M. M. Hedges, Mr. and Airs. X. Wheeler, Mr. and Airs. John A. Patten, Air. and Airs. N. T. Montague, Mr. and Mrs. R. H. Williams, Mr. and Mrs. T. R. Preston, Mr. and Airs. Morrow Chamberlain, Mr. and Airs. T. C. Thompson, Mr. and Airs. T. L. Montague, Mr. and Mrs. O. L. Hurlbut, Air. and Mrs. C. A. Lyerly, Mr. and Mrs. Garnett Andrews, Air. and Mrs. M. B. Ochs, Mr. and Airs. Webster James, Mr. and Mrs. D. P. Montague, Mr. and Mrs. Z. C. Patten, Jr., Mr. and Mrs. W. A. Sadd, Mr. and Mrs. J. B. Pound, Air. and Mrs. George D. Lancaster, Air. and Airs. J. F. Johnston, Mr. and Mrs. R. W. Barr, Air. acrd Mrs. W. B. Davis, Mr. and Airs. Douglas Baxter, Air. and Mrs. W. R. Crabtree, Mr. and Mrs. Lewis M. Coleman, Mr. and Mrs. Newell Sanders, Mr. and Mrs. E. Y. Chapin, Mr. and Mrs. W: B. Riddell,. Mr. and Mrs. J. B. Frazier, Mr. and Mrs. John A. Moon, Mr. and Mrs. C. D. Mitchell, Dr. and Airs. J. H. Race, Mr. and Airs. A. W. Chambliss, Mr. and Mrs. J. P. Smartt, Mr. and Mrs. J. F. Tarwater, Mr. and Mrs. L. D. Drewry, Capt. and Mrs. A. B. Putnam, Mrs. Minnie C. Ewing, Mr. G. F. Meehan, Mr. Sam S. Gerstle, Mr. P. A. Brawner, Mr. C. M. Preston, Air. George M. Guild, Mr. L. M. Mansfield, Dr. J. W. Johnson, Dr. J. AI. Hogshead. EXECUTIVE COMMITTEE.-H. S. Chamberlain, Chairman; H. S. Probasco, C. M. Preston, H. Clay Evans, J. T. Lupton, M. B. Ochs, C. C. Nottingham, Al. Al. Alli¬son, R. S. Faxon, C. E. James, C. A. Raht. EXCURSION TO CHICKAMAUGA PARK.-T. C. Thompson, Chairman; B. F. Thomas, G. F. Meehan, Morrow Chamberlain, W. J. Bass, J. K. McGoodwin. EXCURSION TO HALES BAR LOCK AND DAM.-R. H. Williams, Chairman; John A. Patten, Newell Sanders, George M. Guild, Capt. A. B. Putnam. EXCURSION TO ROCK-WOOD.-F. H. Clymer, Chairman; T. L. Brown, T. A. Wright, J. P. Tarwater, T. L. Peterman. INSTITUTE HEADQUARTERS.-The Hotel Patten. THE first session, held Thursday evening, Oct. 1, in the Banquet Hall of the Hotel Patten, was called to order by Capt. H. S. Chamberlain, Chairman of the Local Committee, who, in behalf of the city of Chattanooga, extended a hearty welcome to the members and guests of the Institute.

Nov 1, 1908

By W. L. Zhong

Probability function integration method is one of the influence function method. It is a widely accepted method in many mining districts in China and Poland mainly because its theory and formulae can well-represent the surface subsidence basins due to longwall mining of flat or near-flat seams. This paper introduces the basic theory of the probability function integration method and determines its 4 basic parameters by analyzing the measured subsidence profiles in eight longwall panels in Northern Appalachian Coal field. It also discusses the two methods for determining the 4 parameters. Finally the acquired parameters are used to predict the subsidence and deformation of the houses for damage assessment. Comparisons are made between the measured and the predicted subsidence. Probability Function Integration Method The probability function integration method for predicting surface movements and deformations is widely used in China and Poland. The governing equation of the method contains five parameters: subsidence factor, a, offset of inflection point, d, tangent of the major influence angle, tan fl, horizontal movement constant, b, and major dispersion angle e (e = 90. for flat seams). Its applicable range iis much larger including seams less than 30' from the horizontal, critical and noncritical mining and soft to hard overburden.

Jan 1, 1986

By J Li, H Hooi, D Payne

Caval Ridge Mine (CVM) is one of the newly established open-cut coal mines of BHP in Queensland, where no tailings dam is planned to be built in order to minimise environmental impacts from mining activities. The waste streams from the Coal Handling and Processing Plant, including fine tailings dewatered by belt filter presses, coarse rejects, and mixed plant rejects, are co-disposed within waste dumps built with pre-strip and dragline spoils. Due to high rejects output (35 – 60% of feed) and low spoil to reject ratio (< 5) the large quantities of rejects bring significant geotechnical and operational challenges to CVM, which are exacerbated by increasing annual production rates and additional rejects from washing coal from an adjacent mine. Further in-house geotechnical review commenced in mid-2014 based on the initial geotechnical studies during the project stage of CVM between 2011 and 2013. The outcomes have enabled rejects disposal at CVM by constructing large belt filtered tailings cells, coarse rejects only dumps, and co-disposal of the mixed plant rejects at dump tip-heads. This paper presents the rejects disposal strategies at CVM from both technical and operational aspects. It also discusses future projects for belt filtered tailings moisture reduction including assessment of tailings clay mineralogy, as well as mixed plant reject co-disposal verification and optimisation.CITATION:Li, J, Payne, D and Hooi, H, 2018. Plant rejects disposal strategies applied at Caval Ridge open cut coal mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 50–60 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By T. H. Yang, K. K. Lee, Z. Z. Liang, C. A. Tang, L. C. Li, Y. Tsui, L. G. Tham

Abstract: A series of numerical tests of hydraulic fracturing in heterogeneous rocks were performed to investigate the influence of pore pressure magnitude and gradient on initiation and propagation of tensile fractures. The numerical tests were run with a Rock Failure Process Analysis code, F-RFPA2D, incorporated with a Flow-Stress-Damage coupling model (FSD). To investigate the influence of pore pressure magnitude on fracture behaviour, “pinch-off” breaking tests, originally employed by Bridgeman to investigate the effective stress law for tensile fracture in a uniform pore pressure field, were numerically modelled. In another numerical test, a double-notched sample, with fluid pressure in one notch while keeping the other one open to the atmosphere, is numerically extended to investigate how the fluid flow direction or the pore pressure gradient will influence the fracture behaviour. The simulation results show that fracture is strongly influenced by both pore pressure magnitude and pore pressure gradient. Keywords: seepage mechanics; heterogeneous; pore pressure; numerical simulation; failure process ZUSAMMENFASSUNG: Um den Einfluss der Wasserdruckgroesse der Oeffnung und der Porisitaet auf den Bruchentstanden und Verbreiten der Tension von Gebirgen zu beurteilen, wurde viele nummerische Pruefungen auf den hydraulischen Bruch in dem Gebirgen aufgenommen. Diese Pruefungen wurden mittels der Analyse- Software F-RFPA2D und Flow-stress-Damage Coupling model ( FSD) durchgefuehrt. Um den Einfluess der Wasserdruckgroesse der Oeffnung auf den Bruch zu beurteilen, wurden auch Bruchpruefung und nummerische Analogexperimenten gemacht, und dadurch wurde die ganze Phase der Bruchentstanden und Verbreiten wiedergezeigt, und die Ergebnissen ergeben sich, dass die Wasserdruckgroesse der Oeffnung und der Porisitaet sehr viel auf den Bruchentstanden und Verbreiten der Tension von Gebirgen beeinfluessen. Schluesselwoerter: Durchlaessigkeit , ungeleichmaessig, Wasserdruck der Oeffnung, nummerische Analog, Zerstoerungspahse Résumé : Une série de simulations numériques a été ménée pour analyser l’influence de la grandeur de la pression de pore et du gradient sur la naissance et la propagation des fractures de tensions par le biais de la simulation numérique des fractures hydroliques dans des rochers hétérogènes . Le logiciel F-RFPA (Rock Failure Process Analysis code ) intégrant FSD ( Flow-Stress-Damage coupling model ) y a été employé. Les résultats des simultations montrent tout le processus de la naissance et de la propagation des fractures sous la pression de pore. Ces résultats nous ont permis de constater que la grandeur de la pression de pore et le gradient exercent une influence importante sur la naissance des fractures dans les rochers et sur leur mode de propagation . Mots de clé : le mécanisme de transfusion ; l’hétéogénéité ; la pression de pore ; la simultation numérique ; le processus destructif

Jan 1, 2003

By Masami Hayashi

The Bureau of Mines estimated the cost for ,3 uranium ion-exchange recovery system using five grades of 17.0, leach solution producing 815,570 pounds of U 0? per year from an ammonium bicarbonate in situ leach solution. The system flowsheet consisted of four unit operations: (1) Multiple-compartment ion-exchange (MCIX) absorption; (2) MCIX elution; (3) precipitation of the uranium as yellow cake, filtering, calcining, and packaging; and (4) waste disposal. The total fixed capital cost of a system treating 2,000 gallons per minute of 0.1-gram-per-liter-U308 leach solution was estimated as $6,888,000. For n basic case of an MCIX system depreciating in 9 years, unit production cost of U308 was $3.51 per pound. A decrease in feed solution grade from 0.[4] to 0.03 gram per liter increased the production cost exponentially. Shorter depreciating periods significantly increased the production cost particularly for the lower grade feed solutions.

Jan 1, 1979

This is the sixth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ The present report covers 54 brands of gasoline represented by 1,480 samples plus those from the Pacific Coast, which were averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were submitted. In some areas reports were received from 8 to 10 companies on the same brands of gasoline, whereas in other areas only one company reported on a brand. Thus, it can be seen that some of the data are more representative than others. The inclusion of data from several cities within some of the districts has improved the report by reducing the number of brands reported by only one company. Several changes have been made in the districts. A new district, Memphis, Tenn., has been formed to include Arkansas and western Tennessee. The Rocky Mountain areas have been divided into three sections. Salt Lake City and Denver form the Middle Rocky Mountain district; Laramie, Wyo., Idaho, Montana, and Spokane, Wash., are included in the North Rocky Mountain district, and Arizona, New Mexico, and El Paso, Tex., have been combined to represent the South Rocky Mountain district. The Cleveland district has been expanded to include Ohio an,"- Indiana. Eastern Pennsylvania, Maryland, and northern Virginia are included in the Washington (D. C.) district. The Atlanta district includes Georgia, South Carolina; Mississippi, and northern Florida.

Jan 1, 1938

By John T. Eastlick

The Banner mining district is about 70 miles northeast of Tucson in the southern part of Gila County, Arizona. Production from the district, valued at about $26 million, is chiefly from copper-silver-lead zinc ores. The stratigraphic section consists of Precambrian conglomerates, quartzites, dolomites, and limestones, Cambrian quartzites; Devonian limestones; dolomites, and shales; Mississippian limestones; Pennsylvanian limestones and shales; and Cretaceous volcanic and sedimentary rocks. Deformation of these rocks presumably started near the end of the Cretaceous, and extended into the late Tertiary. The sedimentary rocks were folded, faulted, and intruded by fine grained diorite, quartz mica diorite, and dacite porphyry. At least four distinct stages of mineralization are recognized. In the first stage of contact metamorphism and the second stage of hydrothermal alteration, favorable zones were prepared for ore deposition. Metallization occurred in three of the mineralizing stages. Magnetite, pyrite, and hematite were deposited near the end of the second stage of hydrothermal alteration. The third stage included the main deposition of sphalerite, chalcopyrite, bornite, and galena. In the fourth and final stage, minor amounts of sulfide minerals were deposited with a late anhydrite and quartz gangue. The ore deposits in the form of veins and veinlets, pipes, irregular massive replacements, and bedded replacements are localized by the extent and distribution of metamorphic and hydrothermal alteration, by the proximity to the intrusive contacts, and by the effects of structural development. Oxidized ores of copper, lead, and zinc constituted the principal production of the district prior to 1940, but, for the most part, supergene enrichment was of minor economic importance. The ore bodies of the district are in the mesothermal class of deposits, occurring as normal metasomatic replacement and vein types.

Jan 1, 1968

By R. B. Sudderth, A. Quiroz G., M. Torres M., C. Salgado Q., J. Fernández O., H. Bravo P., M. Torres B.

SNF FloMin, Inc. has introduced a complete line of extractants for recovery of various metals. Among them are the CuPRO MEX™ Brand of copper extractants that are based on the well- known 2- hydroxy 5-nonylsalicylaldoxime and 2-hydroxy acetophenoneoxime. This paper presents the laboratory and pilot plant trial results for SNF FloMin’s CuPRO MEX™ 3302 reagent, the equivalent to the wellknown ACORGA® M5640 extractant, and the composition of these reagents are described. Some examples of SNF FloMin’s CuPRO-Sim™ Advanced solvent extraction simulator are presented.

Jan 1, 2014

By R. A. Westin

[Polychlorinated biphenyls (PCR's) have been widely utilised as fire-resistant dielectric coolants; in electrical equipment used in mining applicants, including transformers, capacitors, electric motors, and electromagnets. In addition, PCB's have been used in hydraulic fluids and heat-transfer fluids and are present in many oil-filled transformers. The U.S. Environmental Protection Agency (EPA) recently banned the manufacture of PCB's and equipment using PCB's, and imposed strict requirements on the continued use and disposal of existing PCB equipment. This manual discusses the EPA requirements, suggests ways to decrease the risks resulting from continued use of PCR equipment, and surveys the non-PCB equipment that is available as replacements for the PCB electrical equipment presently used in mines.]

Jan 1, 1980

By L. M. Pidgeon

MAGNESIUM metal, with a specific gravity of 1.73, is two-thirds the weight of aluminium and one-quarter that of steel. It is the lightest metal which is stable in the atmosphere. Before the war it had begun, though somewhat slowly, to take a place among the established metals. In 1939, magnesium production on this continent amounted to some 3,000 tons per annum and was confined to one company. At that time, Germany produced perhaps 20,000 tons. The advent of war, however, increased the demand to fantastic heights and introduced production problems of unprecedented magnitude. By the end of 1943, North American production is expected to reach 300,000 tons per annum (1), an increase of one hundredfold. Such a rate of expansion has not been witnessed previously in the history of metallurgy. It has given the metallurgist an opportunity to try new production methods and to learn in a short time what might otherwise have taken many years. The metallurgy of magnesium is still in its formative years and at this time widely different production methods are in operation side by side. This paper will discuss these methods in so far as information is available for publication at this time. A general description of the new Canadian industry will be included.

Jan 1, 1944

By Luke Keeney, Stephen Walters

"The start up of a new mining and metallurgical facility is a crucial step in the life of any mining project. The mining industries record is poor when evaluating processing plant operation relative to design capacity predictions made during feasibility studies. Multivariate geometallurgical orebody characterisation, using principle component analysis, is a method developed for improving predictive processing performance models during feasibility stages of mine development. This paper outlines the application of multivariate geometallurgical characterisation to the Cadia East deposit located in New South Wales, Australia. Cadia East is a low grade high tonnage copper-gold porphyry system in advanced stages of feasibility analysis. A dataset of ~32000 measurements and 150 comminution parameters (A*b and BMWI) has been used to develop class-based characterisation and modelling methodologies. The results of this study outline the development of class-based ore characterisation and provide a technique for analysing and interpreting large and complex geometallurgical datasets for prediction and optimisation of processing performance. The results enable sophisticated population modelling to be conducted which displays deposit scale processing variability, aiding circuit design specifications and predictions during feasibility studies.INTRODUCTIONA feasibility study is the major technical report on which the decision to proceed to production and on which financing is based (Shillabeer & Gypton, 2003). The mining industry’s record is not very good when actual construction time, costs, and operating performance are compared to the projections made in feasibility studies (Ballard, 1983; Gypton & Ward, 2000; Gypton 2002). A study by McNulty (1998) found that of 41 mineral processing and chemical plants built between 1965 and 1995, only 56% achieved design capacity within two years of commissioning and three were closed after failing to achieve design capacity within 36 months of start up (Shillabeer & Gypton, 2003). McNulty (1998) related this underachievement and failure of start up performance to the use of innovative process technology without appreciating and managing technical risk. Factors contributing to technical risk include inadequate pilot plant testing, scaled up prototype equipment without backup, design flaws and poorly understood complex process chemistry."

Jan 1, 2009

By C. R. Whittemore

IT can be truly stated that no branch of the engineering industry has progressed more rapidly in the last few years than that of welding. In spite of depressed economic conditions, this industry has continued to advance along scientific lines, replacing the old hit-and-miss method of welding. The development work is intensive, and increased activity is recorded in every sphere of the industry, new applications of existing methods, together with new processes, being added to those already proved in practice. The general acceptance of the welding processes can be measured by their utilization as a manufacturing tool in the metal-working industries. Many manufacturers have partially or wholly adopted welding. These concerns have on their staffs welding specialists, design engineers, and metallurgists, who are qualified to design and supervise the manufacture of welded parts, at a considerable saving to the purchaser. The steady, consistent, and sound growth of welding is based upon investigation of the fundamentals of the various processes, together with their proper application. The classification of welding processes varies in different countries. In Europe, they are divided into two main classes, namely, heterogenous and autogenous. In the former, the parts are joined, as a ruler without melting the edges, and by using as filler a metal different from that of the object welded. Such welding differs from soldering and brazing in that higher temperatures are required to effect the union of the parts. In autogenous welding, the parts are joined by melting of the edges, with or without the addition of a material similar to the parts being joined.

Jan 1, 1936