Search Documents

By T. A. Rickard

The writing that is effective is woven with a fine texture into an agreeable pattern; it is free from knots, loose threads, and stray fluff. The instrument that weaves this literary fabric, whether it produce a homely sock or a lordly tapestry, a simple story or a learned 'Itreatise, is a disciplined intelligence, as sure as a steel needle, as precise as a swift loom. The simile breaks down at this point, for the product of the pen is instinct with the human spirit and therefore transcends in beauty anything made by a mere machine. If words are to be woven into eloquent meaning, they must be well knit. Upon the relation of words to each other and of groups of words to other groups, known as phrases, clauses, and sentences, depends the success of writing as a means of trans¬mitting thought from man' to man. To be understood beyond question, you should know not only what your words denote but how to build your sentences; you must not only choose your words aright but construct your sentences properly. A sentence is a combination of words that makes complete sense; it says something about something. ' A clause is a subordinate sentence or a sentence within a sentence. A phrase is a group of words without a predicate; it makes sense, but not complete sense. For example: I shall wait for a few minutes before I go home: The whole statement is a sentence; "I shall wait" and "before I go home" are clauses; "for a few minutes" is an adverbial phrase. The orderly arranging of words and of combinations of words is called `syntax'; and from the original Greek form, ouvaeis (suntaxis), is derived the Greek name for an editor,

Jan 1, 1931

By J. D. T. Capocchi, M. B. Mourao

The rate of reaction between iron oxides and carbonaceous materials, agglomerated as pellets, was studied experimentally by measuring the weight loss as a function of time. The effects of temperature, carbon type, inert gas flow rate, pellet size and additions (sodium. carbonate and Portland cement) were determined. It was shown that the value of the apparent activation energy can display large deviations under different experimental conditions; in the present work it was found to be 226.6 kJ/mol. The reaction with coke is slower than with charcoal, and the rate increases as the flow of inert gas in the reaction vessel decreases. Comparison of the rates for pellets of different sizes has shown that for small pellets the initial rate is faster but that it slows down at high conversions owing to the penetration of inert gas into the pellet. Additions of sodium carbonate and Portland cement increase the rate; sodium. carbonate promotes the catalysis of the Boudouard reaction, which is the slowest of the partial reactions. The increase in the rate with Portland cement is attributed to the release of water vapour

Jun 18, 1905

Notwithstanding full concurrence with the dictum of a famous scientist that "definitions are the most accursed of all things on the face of the earth," in view of the considerable confusion which exists in jigging nomenclature, it is considered advisable to commence this paper with the following explanations of the terms which will be used throughout the text.Jig Bed. The whole layer of material lying on top of the jig screen.Ragging. The layer of denser material lying immediately above the jig screen, which is too coarse to pass through this screen and is confined horizontally by the cells of the top grid.Ore Column. The layer of ore pulp between the ragging and the top-water.Top Water. The water, carrying fine material in suspension, which flOiWS over the surface of the jig bed.Hutch Water. The water added to the jig below the screen. (Except for the water discharged with the hutch concentrate, the "hutch-water" eventually becomes "top-water.")Feed Water. The water in the ore pulp fed to the jig.(This water becomes part of the "top-water.")Pulsion. The period of the jigging cycle during which the water is moving upwards relative to the particles in the jig bed.

Jan 1, 1937

By C. D. Anderson

A variety of processing technologies exist for recovery from both primary and secondary sources of rhenium. Currently, there are no known primary rhenium deposits, thus, the method in which primary rhenium is produced is dependent on the commodity of which it is a byproduct, e.g., copper, molybdenum, uranium, etc. In addition, focus on the recovery of rhenium from secondary sources, such as alloy scraps and catalysts, is continually growing. This paper presents a review of both primary and secondary processing technologies for the recovery of rhenium. Key Words: Rhenium, Ammonium Perrhenate, Extractive Metallurgy

Feb 27, 2013

By H. W. Gillett, E. L. Mack

"This report describes the trend of developments in electric brass-furnace practice in the last two years, and supplements Bureau of Mines Bulletin 202, ""Electric Brass-Furnace Practice"", which was published in 1922. In that bulletin it -as pointed out that some of the lines on which electric brass-furnace progress would take place were clear, but others were less so.Developments in foreign countries.Foreign brass-melters have not yet adopted electric melting to an extent comparable to its use in the United States. It is doubtful Whether all foreign countries combined use 100 electric brass furnaces; of these about 35 are of American make (Ajax, Detroit, Baily) and are operating in Canada, Mexico, England, France, Japan, Sweden, Switzerland, Spain, Norway, Germany, Argentina and Czecho-Slovakia.`The Rennerfelt furnace finds some use in Sweden (1)c, notwithstanding its high metal loss on alloys high in zinc, Two German firms are reported(2) to be using the Rochling-Rodenhauser induction furnace on bronze, the average energy consumption being given as 400 kw.-h. per ton. No comment is made on any trouble from the ""pinch effect"", A firm in Switzerland is reported (3) to use three 600-lb., direct-arc furnaces of its own design to melt babbitt, antimonial lead, coinage silver, nickel, copper, and brass. The metal loss on yellow-brass turnings is high. Use Of a direct-arc furnace in England, with precautions aimed to prevent surface overheating, vas abandoned (4) in favor of an Ajax furnace."

Apr 1, 1924

By Danell. R. E.

A drill monitoring system has been developed which measures performance characteristics of a rotary drill and relates this to the material strength and rotary specific energy. The drill monitor is computer based and is used to produce a profile of the relative in-situ material strength as a function of depth. This information has been used in determining the placement of explosive in selective loading of blastholes and estimating the amount of lump product in a particular section of an ore body.

Jan 1, 1989

By Maarten van de Vijfeijken, Marco Rufli

"By using the latest generation of medium voltage frequency converters, new possibilities have arisen to improve the grinding process. Beside all the direct and indirect advantages, several dedicated functions have now been implemented for ring geared grinding mills in the minerals industry. The advanced operational functions ensure a smooth, safe and reliable operation with minimum stress for the mechanical equipment and therefore highest availability of the mill. Several papers have already been presented concerning the benefits of using this state of the art technology for mill drives (Ravani von Ow and Bomvisinho, 2010; Ravani von Ow and Gerhard, 2010). However this paper will not only show and explain the operational benefit of these functions, but will focus on the experiences gained with this kind of sophisticated ring geared mill drive system. Several measurements of different operating conditions (starting, frozen charge remover, controlled roll back, backlash, etc.) made on an installed and commissioned 2 x 5 MW dual pinion ring geared mill drive system will be shown and discussed. Also the accuracy of the load sharing between the two 5 MW motors during starting, normal operation and stopping will be demonstrated using real measurements from an operating system. Finally the inherent features of these drive systems are briefly discussed.INTRODUCTIONLooking at the demands of grinding mills, we can split them into operational, maintenance and protective demands. For smooth and safe operation, it is important that critical situations are avoided as much as possible. Maintenance functionality must be quick and easy to execute, while protection of the system is important during all operating conditions. ABB has considered all these demands during development of their dedicated mill functions. By adding an additional controller (mill controller), not only a lot of application related functionality and protection is included, but also the interface between the mill drive system and the customer’s distributed control system (DCS) is simplified."

Jan 1, 2011

By Gerald Blackmore

This paper discusses the present state and future trends within the coal industry, and then goes into the reasoning behind these planned trends. Such factors as marketing, costs, new mining techniques and machinery, and manpower and human resources are considered. Finally, the author refers to the effect that these trends will have on the coal industry of Cape Breton.

Jan 1, 1968

By D. C. Dahlin

The U.S. Bureau of Mines investigated the magnetic susceptibility of minerals as a function of mag-netic field strength to determine how it might affect the potential for high-field magnetic separation as an alternative to other separation technologies. Single-mineral concentrates were prepared from specimens from the same deposit to compare magnetic susceptibilities of minerals that occur together and from specimens from different deposits to compare magnetic susceptibilities of like minerals. A vibrating-sample magnetometer with a superconducting magnet capable of producing a magnetic field of 7.16 x 106 Aim (90 kOe) was used to measure the magnetic moment of the samples. The data were then converted to specific magnetic susceptibility data and plotted as a function of magnetic field strength. Cursory studies were also completed on the effects of iron content and oxidation roasts on magnetic susceptibility in high fields. The results showed that magnetic susceptibility is essentially constant in magnetic fields above those needed to saturate ferromagnetic constituents. Although magnetic susceptibility is influenced by iron content and by thermal treatment, the changes are not large enough to influence separations in fields above 1.59 x 106 Aim (20 kOe).

Jan 1, 2010

By Sufi Md Gulzar, L B. Roy

Rock engineering tasks like tunnelling, dam and building construction, and rock slope stability rely heavily on properly estimating the rock’s uniaxial compressive strength (UCS), a crucial rock geomechanical characteristic. As high-quality specimen are not always possible, scientists often estimate UCS indirectly. The primary objective of this paper is to assess the efficacy of long short-term memory (LSTM), K-nearest neighbour (KNN), a combination of particle swarm optimisation (PSO) with an artificial neural network (ANN), and adaptive neuro-fuzzy inference system (ANFIS) to estimate the UCS of sandstones from Jharia, Dhanbad, India. Point load index (PLI), porosity (n), P-wave velocity (Vp), density (ρ), and moisture content (%) are the parameters used for the present study. Finally, a comparison was made between the various prediction algorithms outputs. The findings of the study validated the effectiveness of computational intelligence methods in forecasting UCS compared to other models used in this paper. The KNN achieves overall the best results, with an R2 of 0.95 for training, 0.94 for testing, and an RMSE of 0.03 for training and 0.05 for testing.

Nov 23, 2023

By W. G. Hatch

Introduction In November, 1927, a paper was presented at the Annual Meeting of the British Columbia Division by H. A. Pearse(l), in which he described the milling practice at Britannia and set forth the metallurgical results which were being obtained at that time. In the intervening four years, various changes and additions have been made in equipment and practice, which have resulted in marked improvements in efficiency and costs. These changes and their effects are discussed in the present paper. During the past few years two major changes have been made in plant equipment. The first of these was the. elimination of an intermediate crushing stage by discarding two gyratory crushers in favour of two Symons cone crushers. The latter installation-now effects in one stage a greater reduction than was formerly accomplished in two, that is, by the gyratories together with a set of rolls. The second important change in equipment took place when the original M.S. flotation machines were replaced by six Forrester pneumatic machines, so that now the flotation department consists entirely of machines of this type. A number of minor changes and some further additions to equipment have also been effective in raising plant capacity and concentrate grade, while making noticeable reductions in tailing losses and costs of ore treatment.

Jan 1, 1932

By J. Perlacia

"As the bulk handling sector continues its transformation to Industry 4.0, the mining industry, and its harsh working and environmental conditions, provides a perfect spot to study the feasibility of remote analysis and maintenance of the components used for bulk handling. The most important and expensive tools have been adapted to the digital era in recent years, from remotely controlled haul trucks to monitored conveyor belts.However, the big items of the installations rely on smaller parts that have been leftaside, mainly due to the difficultyof adapting them to the Internet ofThings (IoT).The paradigmatic example is the lack of monitored rollers, while all the other components of the conveyorbelt installations (the belt itself, motors, drums, etc.) were monitored some time ago. The main problem is that a failure of a single roller can cause the stoppage of the entire conveyor, due to possible damage to the belt. Thus, the implementation of an integral monitoring system of all the components of the conveyor is a must.The research and development department of ULMA Conveyor Components has been working since early 2012 on the development of monitored rollers, testing all the problems until their final installation in different demanding conditions, from the extreme heat in Australia to the freezing cold of Norway. All the tests have been done under actual working conditions, in real installations and have provided valuable knowledge in the identification of problems, their solutions and the final advantages of a roller monitoring system.Background and current stateThe malfunction of a single roller in certain conveyor belts can force the standstill of the entire installation until its replacement, due to the risk of greater and more expensive failures, such as a rip in the belt. In the case of a bulk handling installation, where a continuous supply of material is necessary, an unexpected stop of one hour could result in huge economic losses."

Nov 1, 2019

By Ian Vaz, Takefumi Takuma

"The New Orleans area has been repeatedly flooded by major storms and hurricanes since its French colonial era. After severe flooding in May 1995, the U.S. Congress authorized a massive flood protection project called the Southeast Louisiana Urban Flood Control Program (SELA) in 1996 to improve interior drainage in Orleans, Jefferson, and St. Tammany parishes. However, the project was not fully funded before the landing of Hurricane Katrina in 2005 and Hurricane Rita, which breached many of the area’s levees and flooded 80 percent of the city. Finally, the project was fully funded in 2008 and has been worked on towards its 2017 completion. Another large project simultaneously worked on in the area is the Hurricane and Storm Damage Risk Reduction System (HSDRRS). This system was designed for a 100-year level of flood risk reduction. One particular project within the HSDRRS rendered successful due to an unconventional method of pile driving that was utilized to install sheet piles to reinforce an existing concrete I-wall. This paper will discuss how and why this non-vibratory method of sheet pile installation allowed the project to be successfully completed ahead of schedule.INTRODUCTIONSteel sheet piles were utilized on many of the SELA and HSDRRS projects for permanent cutoff walls under concrete I-walls or T-walls or for temporary earth retaining walls of drainage structures. Although the SELA Project was established in 1996 after severe flooding the year before, hardly any work was done on it until the two catastrophic storms Hurricanes known as Katrina and Rita triggered its revival. These two hurricanes also triggered the HSDRRS soon after the storms’ devastation. The SELA project authorized to improve interior drainage systems while the HSDRRS project was authorized to raise or restore levees and floodwalls mainly along Lake Pontchartrain, the Mississippi River, and Lake Borgne in addition to other areas. Figure 1 shows the SELA Projects that have been completed, are still under construction, or approved for construction. The projects fully highlighted in yellow within the map specified the press-in piling method. These improvements included drainage systems, pump stations, surge walls, and outfall canals as enhanced protection for future storms similar to Hurricane Katrina that caused so much damage by inundating the New Orleans area in August and September 2005 respectively (Facts and Figures, 2012). The completion of these projects were the responsibility of the U.S. Army Corps of Engineers, New Orleans District.Due to the fact that many of the projects were in densely populated areas, the Army Corps of Engineers specified a non-impact, non-vibratory press-in piling method for driving and extracting sheet piles for many of the projects to mitigate noise and vibration impacts. The soft soil conditions in the New Orleans area was also a contributing factor in the Army Corps of Engineers’ decision to specify this piling method due to the risk of settlement for existing historical as well as modern structures. In addition, there were other projects that elected to use the press-in method without any contractual requirements. One of these projects was the Inner Harbor Navigational Canal Reach II Emergency Interim Repair which was part of the HSDRRS project that has been under construction since its authorization in 2005 (Facts and Figures, 2012)."

Jan 1, 2017

The recent paper by Dr. Edwards upon the copper deposits of Australia furnishes a perspective upon that portion of the Commonwealth's mineral deposits which is the more welcome because it has been long overdue. The paper yields in compressed form and in handy arrangement for reference the more relevant data to end of 1938 for all of Australia's important copper deposits 'past"and. present, and for many of the lesser ones. The information supplied 'obviously' has 15een collected' painstakingly and compiled with discrimination.Such published surveys of a national character have been far too few.The Mineral Resources Survey branch of the Department of Supply and Shipping at Canberra has been engaged for several years upon comprehensive compilations of data concerning each of the more important minerals used in industry. Presumably the results will be published after the war. The group will constitute an impressive and valuable series.As yet the work has not been completed, and, for security reasons, much of that which has been finalized is not publicly available. This makes the paper by Dr. Edwards the more timely.In the compilation of data by those not acquainted at first hand with many of the districts involved it is inevitable that, from reading of the literature alone, certain misconceptions will arise relationships become confused; and some of the more recently acquired information unavoidably fail to be taken into account. One need only compare his own impressions of a district, gained from reading the published literature prior to inspection, with the impressions later arrived at following a visit, to realize the difficulties in appraising the various features,in their proper relationships.On the whole, Dr. Edwards has, kept such misinterpretations at a minimum, which is a tribute to the care he must have exercised in analysing the vast fund of data perused. A few errors of statement, mainly concerning, Queensland deposits, have been noted. None is vital, but in the interests of accuracy it seems well to point them out.QUEENSLANDMount IsaOn page 108 Mount Isa's prospective output of 12,000 tons of copper per year is stated as coming from the Doherty section (O'Doherty, Black Rock mine, R.B.),- the copper ore-body is said to occur in dolomitic limestone (-Page 110)-, and Mount Isa's copper output for 1938 from that source is given as 22 tons. On page 145 the same prospective copper output is stated as coming from a body lying out in the hanging-wall of the silver-lead-zinc...

Jan 1, 1943

By NONE N

Jan 1, 1963

At Waiuta near Reefton there is a remarkable vein of quartz <1 m thick which, apart from small offsets on late-stage faults, is a sheet like body essentially continuous down-dip and along-strike for> 1 km. The vein strikes NNE and dips steeply west (032/78¦W). From 1906-1951 the Blackwater mine produced 740,404 ounces of gold from the vein, called the æBirthday ReefÆ, which was one third of the total production from Reefton Goldfield and the fourth largest gold mine in New Zealand. Within the mine the vein is disrupted into a series of northeast-plunging shoots by late-stage faults. Similar faults, but with larger displacements, were thought in the past to truncate the vein at the northern and southern ends of the mine. The implication of this fault dissection model is that offset remnants of the vein await discovery. This study investigated the geometry of the vein and its relationship to host-rock structures and late-stage faults. A new model considers folding and lithological variation in the host-rocks to be fundamental in controlling the scale and geometry of veining, but does not rule out the possibility of some late-stage fault dissection. The Birthday Reef truncates 200-400 m wavelength folds in Greenland Group host-rocks at c.10¦ angle, that results in variation in the structural properties of host-rocks along strike every ~1350-2500 m. The spacing of fold hinges in the wall-rock veins is equivalent to the strike length of historic mining, implying that the Birthday Reef is probably hosted in a single limb of a fold. Similar relationships between mineralisation and host-rock folds appear to be present elsewhere in the Reefton Goldfield (e.g. Capleston and Murray Creek group of mines). Exploration targets are located one fold wavelength (c.1350-2500 m) further along strike from the Blackwater mine and relatively barren rock is expected in between the mine and target areas. Refining the location of folds and different host rock lithologies, using geophysical data and quality geological mapping, is the key to reducing exploration risks and discovering further resources.

Jan 1, 2000

By Jian Zhou, Shuai Huang, Wenqin Xi, Kun Du

The deep oceans harbor a wide variety of mineral resources that are characterized by their abundance and high quality. Nations worldwide are actively pursuing the exploration and extraction of these resources. This paper provides a concise overview of the mineral resources found in the deep sea, highlighting the challenges associated with their exploitation. Furthermore, it presents a comprehensive analysis of the historical development of deep-sea mining technology and equipment, offering valuable insights into this field. By examining the current issues and obstacles faced in deep-sea mineral extraction, this study concludes that the future of deep-sea mining lies in the direction of automation, intelligence, and standardization. Additionally, it identifies the key technological advancements that need to be achieved in order to overcome the challenges associated with deep-sea mining.

Jan 5, 2024

By M. Nehdi

Deficient surface disposal systems of sulfidic mine waste often cause severe contamination of surface streams and groundwater reservoirs due to the oxidation of sulfide phases. The subsequent generation of leachates characterized by high acidity and elevated concentrations of toxic elements (commonly known as acid mine drainage) jeopardize the health of contiguous ecosystem. Stabilization/solidification (S/S) is recognized as a promising solution for treating such wastes. S/S processes generally mobilize alkaline and/or cementing materials/additives that act as neutralizing and/or binding agents. In the present research, industrial byproducts, namely, cement kiln dust (CKD) and Class C fly ash (FAC) have been used as candidate materials along with the partial addition of sulfate-resistant cement (SRC) in the S/S of polymetallic sulfidic mine tailings (MT). The effectiveness of S/S was assessed by comparing laboratory experimental values obtained from unconfined compressive strength, hydraulic conductivity and leaching propensity tests of S/S samples with regulatory standards for safe surface disposal of such wastes. Despite general regulatory compliance of compressive strength and hydraulic conductivity, some solidified/stabilized-cured matrices were found unable to provide the required immobilization of pollutants. Solidified/stabilized and 90-day cured mine tailings specimens made with composite binders containing (10% CKD + 10% FAC), (5% SRC + 15% FAC) and (5% SRC + 5% CKD + 10% FAC) significantly impaired the solubility of all contaminants investigated and proved successful in fixing metals within the matrix, in addition to achieving adequate unconfined compressive strength and hydraulic conductivity values, thus satisfying U.S. EPA regulations. Laboratory investigations revealed that, for polymetallic mining waste, leachate concentrations are the most critical factor in assessing the effectiveness of S/S technology.

Jan 1, 2008

By J. Convey, S. L. Gertsman

"THE EXPANSION of steel capacity is seldom spectacular. It may be for this reason that the remarkable progress made in Canada has not been generally recognized. In 1950, Canada's output of steel ingots amounted to 3,270,000 tons ( l ), which is a ll8 per cent increase over the tonnage produced in 1939. It can therefore be readily seen that Canada's growth curve for steel production is climbing at a rate paralleling her growth as a nation. It is by no means •an exaggeration of its importance to consider the steel industry as the cornerstone in the economic structure of Canada's manufacturing activities. From the humble diaper pin to the giant members of massive bridges, fortifications, and other steel structures, steel accompanies us as a necessary and inescapable companion in our journey through life. The Age of Steel has a literal meaning, and refinements in the manufacture of the products of steel are adapting it to more and more varied uses as time passes.The integrated iron and steel works of Canada fall into two natural geographical divisions. One has its base on the Great Lakes and draws its supply of •coal and some of its ore from the United States. In this division lie the works of the Algoma Steel Corporation, at Sault Ste. Marie, at the junction point of lakes Huron, Superior, and Michigan; and the works of The Steel Company of Canada, at Hamilton, on lake Ontario."

Jan 1, 1952

By N. Shariatmadari

In recent years, determining bearing capacity of piles from in-situ testing data as a complement of static and dynamic analysis has been used by geotechnical engineers. In this paper, different approaches for estimating base bearing capacity of piles from SPT data has been compared and evaluated. A new method for pile base bearing capacity in sand is proposed using SPT records. Data averaging, failure zone extension, and plunging failure of piles have been addressed in the proposed approach. A data bank comprising 10 full scale static load tests on instrumented piles and 26 dynamic tests, analyzed with signal matching technique by CAPWAP software, was used for validation. The SPT data that was performed close to pile locations is also included in the data base. Comparison of current methods by error investigation with Log-Normal approach demonstrates that the proposed method predicts pile base capacity with more accuracy and less scatter in comparison to other methods.

Jan 1, 2006