Search Documents

By Harry W. Campbell

A Bureau of Mines investigation identified no mineral deposits in the Lost Creek RARE II area. Sand and gravel has been mined from alluvial flood plain deposits just outside the RARE II boundary. An oil and gas lease application which includes the eastern portion of the RARE II area is pending. Abundant basalt in the area can be crushed and used as aggregate; but it could not compete with similar deposits in more favorable locations, or with cheaper substitutes such as volcanic cinders or sand and gravel which are available outside the study area closer to major markets. No indication of coal or geothermal energy resources was found. INTRODUCTION Location and Access The Lost Creek RARE II area encompasses 8,300 acres (3,400 ha) of Lassen National Forest in north-central California, about 20 mi (30 km) north of Lassen Peak. The closest city is Redding, California, 50 air mi (80 km) southwest. Peripheral access is provided by State Highway 89 passing near the western RARE II boundary (fig. 1). The Pacific Crest Trail traverses the western margin of Hat Creek Rim adjacent to the eastern boundary of the area.

Jan 1, 1983

By . M. Muskat

A THEORETICAL consideration of the mechanics of various water-flooding systems with the viewpoint of comparing their relative merits involves the study of two fundamental properties of such systems. On the one hand, it is important to determine the efficiency of the flood as measured by the percentage of the total area that is swept out by the encroaching water before water actually reaches the output wells. This is really a measure of the regional tendency of the water to "bypass" the oil. On the other hand, the various systems must be compared from the viewpoint of their resistances which determine the rate of fluid production obtainable for given pressures maintained at the water input wells. The first of these questions has been studied and very definite answers have been obtained by means of simple electrolytic models.1 These models showed that, in an ideal system, the percentages of the areas flooded out before water reaches the output wells are about 57 per cent for the direct line-drive flood (the input and output wells being equally spaced and placed in alternate parallel lines), 74 per cent for the regular five-spot network, and 79 per cent for the seven-spot network. With respect to the efficiency of the usual flooding arrangements, they are, therefore, given quite accurately by the above numbers. With regard to the resistances of the flooding networks, electrical conduction models have also been used successfully2 and are well adapted to the problem of determining experimentally the pressure distribution and streamlines, or over-all resistances of specific flooding networks. However, such models do not permit readily a study of the effect of changing dimensions or configuration within a network, since a new model must be made up for each set of dimensions considered.

Jan 1, 1933

By G A. Challis, A B. Christiel

Microprobe analyses of electrum grains in some Hauraki Au-Ag deposits indicate that gold fineness is in the range of 500 - 800 (50 - 80 per cent Au), but for most deposits the range is usually narrower than this. The electrums contain minor amounts (<0.8 per cent) of copper, arsenic, antimony, mercury, iron, and sulphur. Platinum and palladium were analysed for but were not detected (detection limit 0.24 per cent for Pt or Pd). For some deposits (eg Waihi), the average fineness values for the analysed electrums correspond fairly well with the electrum fineness determined by assay during the historic mining operations.

Jan 1, 1992

By Joseph D. Davis, G. S. Scott, Palmer B. Place

In the course of investigations made by the Bureau of Mines in cooperation with the Trent Process Corporation, into the properties of mixtures of oil and coal, a comparative study was ma.de of the 'behavior of these mixtures and their cons ti tuents on destructive distillation. Mixtures of a petroleum oil and bitminous coal were first distilled under carefully controlled conditions, and then charges of the eame oil and coal were distilled separately under similar conditions. The quantity and quality of the distillation products were determined, and. resul. ts were compared. This comparison furnished a basis tor judging whether grea, ... er values in products can be obtained by distillation of oil and coal in mixtures than· b:, their separate distillation. In making the mixtures, the method used in t~e Trent process for cleaning coal was followed. The paste or plastic emulsion of oil and coal obtained is called "amalgam".••• When finely pulverized wet coal is mixed with approximately one-third its weight of. oil and agitated with a large excass of waj;er, the coal and oil agglomer-. ate to form a paste or amalgam. A large portion of the extraneous ash original.17 in the coal remains suspended in the water, with which it can be decanted from the amalgam. Ir the latter is now thoroughly drained and kneaded after the manner ot working butter, most of the excess water enclosed can be removed. This, .in brief, constitutes the Trent process for cleaning coal, The effectiveness of the process for cleaning coal has been studied••••. by the Bureau, and the results of the study show, in general, a high ash reduction an:l good recovery of combus ti bl e f'rom coals of medi ,mi and hi~ rg,nk. With coals of tht lowest rank, such as li@!Rlites, the process is only moderately auccessf'ul, owing to the difficulty attending the preparation of coherent amalgams, Oil losses to wate~ and refuse are small, and apparently it would be practical to rotate the same oil in the cleaning process if some efficient method were devised for recovering it from the amalgam, so a distillation process naturally suggested itself.

Dec 1, 1921

By L. Andrews

Keywords: mineralogy, phase-chemical, chemical-looping combustion, XRD, SEM, EDS, QEMSCAN, PGM, slag, matte, ilmenite Mineralogy, traditionally associated with concentrator studies, is being increasingly applied to problems in pyrometallurgy. Such investigations commonly make use of a number of techniques, and the results are combined for a meaningful interpretation, which can lead to a successful solution. Mineralogical applications are described from pyrometallurgical operations. Examples are given of studies and investigations involving mineralogy in chemical-looping combustion, feed monitoring to platinum-smelting furnaces, and losses to slag in base metal and platinum smelting.

Jan 1, 2011

By E. J. Ripling, M. W. Toaz

Tensile tests were conducted on pure magnesium and on four commercial alloys over a variety of temperatures and strain rates. The high positive slope of the ductility vs testing temperature curves that is found over a short range of testing temperatures for these materaturerials was shown to result from the fact that the microstructure was not stable at these testing temperatures. Pure magnesium did not display a transition temperature, although its sub-room temperature ductility was low. This poor ductility resulted from a grain boundary weakness. The aluminum-bearing commercial magnesium alloys had a higher ductility than the pure magnesium. ness.Thealuminum-bearingcommercialThese alloys did exhibit a transition temperature and grain boundaries that were stronger than the grain material. Both pure magnesium and the commercial alloys began initiating cracks at strains equal to one half of their fracture strain. MAGNESIUM base alloys' enormous potential as structural materials lies in their high strength to weight ratios. At present, the high strength magnesium base alloys such as AZ-80, which will be discussed later, have about as high a tensile strength to specific gravity ratio as the highest strength wrought aluminum alloy, 75s-T6, and, of course, a much higher strength to weight ratio than structural steel. Further, since the magnesium base alloys develop their high strength to weight ratios with moderate strengths and extremely light weights, the ratio of load carrying capacity to the weight of many structures is relatively higher for the magnesium base alloys than their strength to weight ratios would indicate. This results because judicious increases in section size, such as increasing the depth of bending members or adding reinforcing ribs, can frequently increase the weight of a structure linearly while the strength and stiffness increase as the second or third power of the added weight. Strength and rigidity must be designed into lightweight structures by those techniques which establish multiaxial stress states. Consequently, strong, lightweight structures frequently also possess a greater propensity toward brittle failures. In order to insure against these catastrophic failures, an extra premium must be placed on ductility and toughness in light alloys. Current knowledge of the ductility and toughness behaviors—notched behaviors—of magnesium base alloys is limited.* Most of the magnesium base alloys * The state of present knowledge regarding the effect of testing temperature on mechanical properties has recently been summar-ized by Pritchard.' crystallize in the hexagonal system, so that they are expected to exhibit a tough and ductile to brittle transition temperature. Actually, a transition temperature behavior has been reported for commercially pure magnesium in the literature, but the characteristics of this transition temperatureh uggest that it may not be a transition in the usual meaning, but simply the onset of some thermal softening, a performance much like that which face-centered-cubic lead might exhibit slightly below room temperature. If transition temperatures do exist, such important questions as the manner in which they are affected by internal variables such as chemical composition and grain size, or the effect of external variables such as rate of straining or notch severity have never been investigated. The investigation reported upon herein was undertaken in order to define some of the mechanical behaviors of the magnesium base alloys better, to gain a better understanding of the influence of some of the above listed variables, and particularly to understand their effect on ductility and toughness better. Material and Procedure Material-—Pure magnesium and four commercial alloys were used in this investigation. The alloys were selected so that chemically they made up a series with approximately the same minor alloying

Jan 1, 1957

By W. A. Lang

"I.-IntroductionAn attempt bas been made in this paper to provide a basis for appraisal of the future of the coal briquetting industry in Alberta by outlining the processes used for briquetting various ranks of coal, by specifying the requirements of a briquetted fuel, by indicating .the status of the industry in the United States, by giving developments in Western Canada, by assessing costs of processing, and by discussing briquetting researches in progress. Much of .the detail bas been omitted since this might mask, rather than reveal, the more important phases of the problem. Reference will be made when possible to published articles where many of the details can be obtained.It should be stated at the outset that, in the writer’s opinion, there are three possible developments in Alberta as regards briquetting: (a) an expansion of the briquetting of the fines of • non-coking and coking coals of semi-anthracite, and of low and medium volatile bituminous rank; (b) the processing of the fines of high-volatile C bituminous coals; and (c) the upgrading of the lower rank high-moisture sub-bituminous coals. Details of the chemical and physical properties of these coals can be obtained in publications of the Research Council of Alberta (1, 2), and of the Fuel Research Station, Bureau of Mines, Ottawa (3).Semi-anthracite and low and medium volatile bituminons coals occur in the mountain areas of Alberta, where, during the upthrust of the Rocky mountains, the coal beds served as the sliding surface. This resulted in the coals being; crushed and consequently they contain a h1gh percentage of fines. In some cases they are high in mineral matter and require to be cleaned before being processed. However, the cleaning of fine coal is both difficult and costly. Both the amount of fines present in the mine-run coal and the amount of mineral matter associated with the coal have increased through the introduction of mechanized mining and through the recovery of coal by stripping operations."

Jan 1, 1950

By Tapiwanashe Chenje, David Hewitt, Peter Radziszewski

"Steel media wear is a major cost component in mineral processing. In the case of existing operating mill, steel media wear prediction can be used to help compare the performance of steel media from different suppliers before completing marked ball tests. It can also be used to investigate how ores from different site of a given mine affect steel media wear. In the case of Greenfield cases, steel media wear prediction can be used to estimate the cost of steel media for a given feasibility study.This paper presents a wear testing and prediction methodology that ties together abrasion wear and corrosion wear testing results through the use of a simplified discrete element charge motion model. The experimentation dimension to this methodology takes samples for steel media, mine site ore and water to determine abrasive and corrosive wear parameters of a given media, ore, water set.The test methodology development is illustrated along with a comparison of wear predictions with observed wear rates in some operating mills. A case study is included that illustrates how this methodology was used to estimate steel media wear performance. The paper closes with a discussion on the use of parts of the experimental methodology to investigate other abrasive wear conditions such as liner wear, paste backfill piping and ore breakage as well as avenues for future test development.INTRODUCTIONThe cost of comminution processes represents a significant part of the overall costs of a mining operation. Grinding media/liner wear alone accounts for 15-25% of the total operating cost. The annual steel grinding media consumption is approximately 2.5 mtpa or 0.3% of total world steel production [Smorgon Steel Group, 2005]. Using an estimated grinding media cost of about US$0.75/kg [Halbe and Smolik, 2002], gives a media cost of over US$1.875 billion per annum. Mining continues to shift towards exploitation of lower grade ores as the higher grades get depleted. These low-grade ores require finer grinding for the liberation of the value minerals, and hence it can be assumed that grinding media consumption will also continue to rise.The Bond abrasion test, dating back to 1963, [Weiss, 1985] is still used to estimate the total mill media wear. This is a purely empirical test based on the ore. From Bond abrasion index tests, it is possible to determine a wear rate using the following function:"

Jan 1, 2009

Study on Treatment of Wastewater Containing Heavy Metal Ions Using Modified Oceanic Cobalt-Rich Crusts

Sep 13, 2010

Recent literature is reviewed with emphasis on the design and scale up of mixers. Most important aspects of mixing have resulted from the study of Newtonian fluids and only a minor attempt has been made to extend the work to non-Newtonian materials.The rheology of non-Newtonian materials is outlined and the typical behaviour of mineral slurries is indicated.The importance of flow velocity, flow pattern, and fluid turbulence is discussed with relation to suspension of solids and rate of reaction.Data on experimental leaching of ore from Mary Kathleen, Queensland, show the effect of different mixing impellers.In conclusion, factors involved in the selection of a mixer are presented with emphasis on economic appraisal after pilot experimentation.INTRODUCTIONThe subject of mixing has attracted considerable attention during recent years, but relatively little work has been undertaken for the study of non-Newtonian materials. Most work has been restricted to Newtonian fluids because there are less inconsistencies in such study.Mixing, by definition, implies blending or combining, and ranges from gentle mixing which blends the contents of a large tank in 24 hours to violent mixing which completely homogenises the contents of a tank within seconds. Metzner and Otto (1957) have pointed out the present lack of knowledge on the degree (or quality) of mixing. Apart from this fact the design of mixers for Newtonian materials would seem to be reasonably certain.Both capital and operating costs rise rapidly with increasing mixer size. Therefore the design, or selection, of a mixer is a matter for economic consideration in the overall aspect of plant design and operation.

Jan 1, 1961

By Mutombo Nombe, Avimanyu Das, Rick Honaker

Enhanced gravity separators (EGS) provide a more efficient separation than froth flotation when cleaning coal in the 150 x 25 µm particle size range. To improve the performance of an EGS unit, air bubbles were injected into the feed stream in an attempt to decrease the apparent density of the coal particles due to the formation of bubble-coal particle agglomerates. Air injection had a significant impact on operating characteristics and separation performance. Coal recovery was increased by 10 to 20 absolute percentage points while a 2 percentage point drop in the minimum product ash content was also achieved.

Jan 1, 2005

By J. D. Steenkamp

Keywords: Thermal, conductivity, diffusivity, expansion, history, density, specific heat capacity, industrial rich high-carbon manganese slag The thermal conductivity of slag is an important parameter in the design of furnace-containment systems based on freeze-lining technology. Literature indicates that the crystal content of a slag has a significant influence on its thermal conductivity. Industrial, rich, manganese-bearing slag was cooled at different rates to create samples with different microstructures. The coefficients of thermal conductivity of these samples were measured in a nitrogen atmosphere from room temperature to 990°C at 100°C intervals. The laser-flash measurement technique was used for this purpose. Follow-up investigations included XRF and XRD and modelling in FACTSage.

Jan 1, 2011

By E. L. Oliver

IN OFFERING a few comments and suggestions on trends in mining practice, and the methods and tools of tomorrow's mining, perhaps it will be appropriate to start with the subject of education. Charles Kettering, one of the best-known scientists and experimentalists in the automotive industry once said, in effect, that tech- 111ca1 schools have to be carefid not to teach a lot of hard and fast rules that may have been true once, but aren't so any more, or won't be presently. Possibly the mining school of the future will concern itself less with what has happened and more with what is going to happen. It will be built about or around problems. Such a school will be judged, not by the number of its students but by the quality of its improvements. To such a school the industry will send for men to solve particular problems. The industry will doubtless at some time sup- port such a school financially though a lot of hard work will be required to organize miners to undertake such financing, primarily because the mining industry, other than that concerned with iron and steel, is too loosely knit. Each company tends to its own knitting too closely for its own good. Wouldn't it be splendid if the mining industry would finance a "problem school" as suggested by Mr. Kettering and others.

Jan 1, 1939

By Christopher J. Bise

INTRODUCTION Traditionally, the purpose of mine ventilation has been defined as diluting, rendering harmless, and sweeping away hazardous gases which may accumulate in the mine workings. In addition, the ventilation sys- tem must keep the mine air as close as possible to the composition of the outside air in order to provide a healthy environment for mineworkers and to prolong the useful life of mine equipment. When plans are being developed for opening a new mine, sound engineering dictates that a calculated estimate be made of both the maximum air quantity requirement and the accept- able mine pressure (head) loss related to the under- ground layout and projections. For efficient mine ventilation, the two problem areas that demand constant attention are (1) the control of fugitive air (through short circuiting or leakage) and (2) the provision of ample airway capacity. Fugitive air is that quantity of air which enters the mine but short-circuits the mine ventilation system through improperly constructed stoppings, doors, overcasts, etc.; it represents an investment in power consumption (to move the air by the fan) while providing little, if any, return on the investment. Typically, efficient mines are those that can deliver 50% of the air handled by their fans to the working faces. Paying close attention to a new mine's ventilation system at the outset can provide numerous benefits during the later stages of mine development. It has often been noted that the main cause of trouble in many mine ventilation systems can be found within a radius of 2500 ft from the fan installation. Ample airway capacity is essential to maintain the mine's head loss within manageable limits. Similar to an industrial ventilation setting, the mine's headings are the ductwork for the handling of air. The difference between normal industrial ventilation and mine ventilation is apparent when more capacity is needed; a plant can install new or larger ductwork, but it is difficult for a mine to install new entries or enlarge existing entries. Air velocities are usually maintained under 800 fpm to limit the stirring up of dust in the intakes. With this in mind, it is usually simple to estimate the number of entries required in the ventilation system. The problem that often arises, though, is when the system's capacity is overestimated and the required head loss to achieve the desired quantity is excessive. Experience has shown that problems are often encountered when the mine's condition requires much more than three inches of water gage to ventilate the mine on a day-to-day basis. Thus, if proper attention is not paid to these parameters in the preplanning and initial development of a new mine, it may take an extremely high water gage to achieve the ultimate quantity. This chapter will not delve deeply into the theory of mine ventilation; many other books have been writ- ten on that subject. Instead, the following sections will point out the important considerations that should take place before the development of a mine ventilation system, as they relate to normal industry practice. FUNDAMENTALS OF AIRFLOW Volume Versus Water Gage The common method of measuring ventilation pressure is in terms of inches of water gage (wg); one inch of water corresponds to a pressure of 5.2 psf (pounds per square foot). Further, airflow follows a square-law relationship between volumes and pressures where, as shown in the previous section, a doubling of quantity requires a quadrupling of pressure. Table 1 shows how heads and quantities are related. Using Table 1, it is readily apparent that, for the same mining conditions, an increase in pressure from one inch wg to three inches wg results in only 34,640 cfm when the initial quantity is 20,000 cfm. Pressure Losses Pressure losses in mine ventilation systems are caused by friction between the heading walls and the air stream and by shock losses due to abrupt changes of the air stream caused by obstructions. The common pressure-loss formula for mine ventilation is: [ ] where H is the pressure loss in inches of water gage, K is the coefficient of friction, L is the length of the airway in feet, 0 is the airway perimeter in feet, V is the air velocity in feet per minute, and A is the cross-sectional area of the airway in square feet. Table 2 lists the US Bureau of Mines schedule of friction factors (K) for mine airways. Recent research indicates that the values of K are slightly less for coal mines than those presented in the USBM Schedule, and Table 3 should be consulted in this instance. It should be

Jan 1, 1986

By A. N. Veltmeyer

"INTRODUCTIONTeck-Corona Operating Corporation's David Bell Mine is located 35 Km east of Marathon, Ontario. In conjunction with its 1000 tonne per day gold concentrator, the company operates an effluent treatment plant for the treatment of mill, mine and site effluents prior to environmental discharge. This paper provides a brief overview of treatment strategies and methods, employed to detoxify final effluent.WATER MANAGEMENTThe tailings impoundment basin, located 3 Km south of the plant site, provides storage capacity for all process effluents and site run-off. Basin supernatant (reclaim water) is recirculated to the plant for reuse as process water, in order to minimize fresh water consumption. As site run-off and limited fresh water intake exceed natural losses due to evaporation, reclaim water in excess of process requirements is passed through the effluent treatment (ET) facility to control tailings basin level by providing regulated discharge of environmentally acceptable effluent. (Figure 1)PASSIVE TREATMENTTo reduce treatment costs and burden on the ET facility, reclaim water is fed to the plant to take maximum advantage of natural destruction processes occurring in the tailings basin.These include: volatilizationphotodecompositionbiological oxidation and precipitationstorm water dilutionConcentrator recovery techniques (Figure 2) are directed toward maximizing gold recovery while limiting the addition and extraction of contaminants requiring disposal and eventual treatment.Currently ore ground to 90% -200 mesh is pre-aerated at pH 9.0 with lime for 18 hours prior to 30 hours cyanidation at pH 9.5 with low cyanide ion excess (70 ppm).Pre-aeration passivates cyanicides prior to cyanide contact. This reduces cyanide consumption and the formation of cyanide complexes. In conjunction with recovery requirements low pH is maintained to retard the dissolution of stibnite into its antimony and sulfide components."

Jan 1, 1989

By Jonisha P. Pollard, F. Nasarwanji, Lydia M. Kocher

This study identifies nonfatal injury incidence rates, nature of injury, work activities, glove usage, and sources of hand and finger injuries in the U.S. mining industry, as reported to the Mine Safety and Health Administration (MSHA) from 2011 to 2017. Hand and finger injuries occur at a rate of 6.53 per 1000 full-time employees, which is nearly double the rate of the next highest affected body part, the back.

Feb 24, 2022

By Joachim Klein, Frank Reimann

Nodular-graphite cast iron (GGG) is a material similar to steel, and one which exhibits excellent properties, in particular for components exposed to pressure. GGG cast iron has been used in many cases when sinking mine shafts with conventional tubbing. With linings made of cast iron tubbings (the backfill concrete is not integrated into the calculations, and merely serves as bedding) the properties of the cast iron can be made full use of, provided the tubbing is made to the appropriate cross-section. Calculations have shown that better static values can be arrived at when using cross-sections other than those of tubbings made to conventional German standard. The cross-sectional design of the new types of shaft lining made from GGG is to be developed on these lines irrespective of the cast iron structure being only stressed component or its restistance function being combined with the one of concrete. GGG 50 is used for the first time to make the reinforcing inner liner of a main shaft currently sunk in Germany. The physical properties of nodular-graphite cast iron, strength and deformability, suggest that, in the future, its application will not be restricted to shaft support but also in tunneling. New moulding techniques with better three-dimensional modelling resulted in new tubbing designs as installed e.g. for the Hannover underground at present. Shield-driven tunnels have to withstand earth and water pressure, apart from axial machine loads. In this field time is money as well. Therefore easy handling and quick installation are necessary for successful, use. Last but not least, safety is of first-order importance for work in shaft sinking and tunneling. Cast iron lining systems, accordingly, are adequate systems, in particular for excavations underneath water for transport systems and for goods and passengers.

Jan 1, 1987

By F. Boudreault, M. J. Scobie, J. Szymanski, C. Hendricks

The development of new stoping methods and more effective control over dilution, recovery and fragmentation depends on improved accuracy in blasthole drilling. The mechanisms and factors which control accuracy are poorly understood. Canadian blasthole stoping and the practices adopted for monitoring and controlling drilling accuracy are reviewed. The techniques and problems associated with blashole set-up and trajectory surveying are discussed. Four new blasthole trajectory survey systems are evaluated on the basis of their performance in recent underground trials. Conclusions are drawn as to the technological developments required so that more precise control over drilling accuracy can be achieved.

Jan 12, 1992

By J Youngson

Gold placers can be difficult to locate in areas where tectonic activity and paleogeography have changed significantly since placer formation. Existing placer exploration models are useful in areas that have a relatively simple geological history, identifiable relationships with parent sources, or a history of placer mining. However, exploration becomes increasingly difficult in areas where tectonic activity and sedimentary recycling repeatedly redistribute the gold. Gold placers in the Waitaki River catchment, North Otago, New Zealand have no primary source within the catchment. During the Eocene placer gold was transported by a river ('Buster River') that flowed in a northeast direction from Central Otago toward a coastline at Maerewhenua, North Otago. This river and coastal system was inundated by marine transgression during the middle Tertiary. Since the Miocene its placer deposits have been uplifted and eroded and any links with parent sources have been severed. Changes in paleogeography resulted in local reconcentration and local dilution of placer gold in different areas in the Waitaki catchment. Thin veneers of old Waitaki River gravels (Kurow Gravels), containing gold recycled from the older placers, have been deposited unconformably on strath surfaces cut into Tertiary or older rocks. These gravels along with remnant Eocene fluvial and shallow marine strata provide potential placer exploration targets. Uplift and erosion of non-auriferous rocks in the Waitaki catchment to the west and north of the study area has resulted in considerable dilution of potential placer deposits downstream, especially in areas of gravel aggradation. We present a placer exploration model that is founded on answering fundamental questions pertaining to the paleogeography and geological history of the sediments associated with the placers.

Jan 1, 1999

A series of fault slip seismic events have occurred at Garson mine. The events have occurred during development advancement exposing faults, after the extraction of single stopes due to mining induced stress change, and due to time effects after delays of many days during which no mining had been conducted. This paper discusses the study completed consisting of a global or holistic approach aimed at mitigating some of the risks associated with the structurally controlled rockbursts at Garson. Background Garson mine is located in the south east area of the Sudbury Basin (Ontario, Canada). Mining occurs in two main ore bodies (the #1 Shear and the #4 Shear) which are copper-nickel-sulphide and occur within shear zones that (as well as the ore bodies) strike approximately east-west and dip steeply south. From the north (footwall), lithologies progress (Figure 1a) from norite (NR), to greenstone (GS), and finally to meta-sediment (MTSD). A generally WNW-ESE striking, bifurcated sub-vertical dyke of olivine diabase (OLDI) cuts the series. The current active mining block at Garson is between 4700L and 5100L (levels denote depth in feet below surface).

May 1, 2009