Search Documents

By J. H. Gasper

A cost analysis for two alternative contour mining methods is performed to compare their results. The methods evaluated are: 1) Front-End Loader/Truck Haulback and 2) Scraper Haulback. Before performing these analyses, output requirements and equipment needs are found based on integrating geometric limitations with material properties. The final geometric design establishes limits on clearances, congestion problems and grades (with associated running surface materials). All calculations are kept practical, with assumptions clearly stated. The cost analysis is a unique, easily utilized compilation of several different approaches incorporating cost engineering principles. The strengths of each are welded into a cohesive entity once again aimed at practical application. The results are presented in tabular form.

Jan 1, 1992

By S. J. Schatzel

In order to better understand the effects of longwall mining on the methane reservoir overlying the panel, the National Institute for Occupational Safety and Health/Pittsburgh Research Laboratory (NIOSH/PRL) designed and implemented a vertical borehole monitoring experiment (BME) on an active longwall panel. The mine operates in the Pittsburgh Coalbed in Greene County, Pennsylvania. The BME site was located away from either end of the panel to avoid mechanical influences caused by the draping of overburden in this region and was positioned at the same distance from the tailgate gateroad as the mine?s gob gas venthole sites. The borehole drilling depths and monitoring intervals were chosen to address a different stratigraphic zone in each of the three planned holes. The monitoring boreholes were positioned perpendicular to face advance using a close spacing pattern of about 15 m (50 ft) between collars. Boreholes were instrumented downhole and on the surface for various measurements. It was observed from the field data that the gob gas venthole fracture network formed 24-46 m (80-150 ft) ahead of the mining face. Overburden permeability?s within the same test zones increased 100 to 500 times following undermining. The borehole test interval within the fractured rock responded to overburden gas pressure while the test interval in the caved zone responded to mine ventilation conditions. Eight months after the boreholes were undermined, slug testing indicated permeabilities had increased further in the fractured rock zone. Measurements of surface movement indicate that the permeability development observed in the boreholes is a product of vertical subsidence without lateral movement within the tensional rock mechanics zone on a supercritical longwall panel. Results from this study suggest that maximum permeability in the longwall panel overburden is achieved 58 to 190 m (190 to 620 ft) behind the longwall following maximum compaction of the overburden.

Jan 1, 2009

By Y Chen, G Xu, B Albijanic

High concentrations of airborne coal particles is the main reason leading to health and safety hazards in underground coalmines. Water spray is one of the effective methods to suppress coal particles in mine sites, but the use of plain water is not effective enough to capture coal particles. By adding surfactants, coal wettability can be improved which will increase the coal dust suppression efficiency. In this study, a modified sink test was employed to evaluate coal wettability in the presence of two anionic surfactants: sodium dodecyl sulfate (SDS) and sodium dodecyl benzene sulfonate (SDBS). Sink rates were calculated by measuring sink weight over test time. Different surfactant concentrations (0.01 per cent, 0.05 per cent, 0.1 per cent, 0.2 per cent and 0.4 per cent) and two types of water (tap water and deionised water) were selected to investigate coal wettability over three size ranges (0–38, 53–75 and 75–90 µm). The results show that both SDS and SDBS surfactants can lower the water surface tension and improve coal wetting performance. Sink rates increased as the surfactant concentration increased, and surfactant solutions prepared by tap water performed better than deionised water in enhancing coal wettability. Also, coal wettability varied for different coal particle sizes; the smaller coal particles were, the worse the wettability they possessed.CITATION:Chen, Y, Xu, G, Wang, R and Albijanic, B, 2017. Study on coal wettability for dust suppression in the presence of surfactants by sink test, in Proceedings Australian Mine Vent Conference 2017, pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

Observed mineral assemblages in the Mt. Lyell copper deposit can be correlated with phase equilibrium investigations in the systems Cu-Fe-S and Fe-Zn-S. The trend of crystallization (or paragenetic sequence) of the ores is reflected in a progressive increase in the Cu: Fe and metal: sulphur ratios of the assemblages. This trend agrees with the regional zoning of the district. Tentative relationships between the paragenetic sequence, sulphur vapour pressure, and temperature are presented graphically. The absence of a suitable geological thermometer prevents precise elucidation of the range of temperatures and pressures which existed during crystallization.INTRODUCTIONRecent phase equilibrium investigations of metal-sulphur systems at the Geophysical Laboratory, Washington, D.C. provide valuable information on the stability relations of a number of important sulphide minerals. This data, when applied to natural ore deposits, may be expected to clarify two special problems which confront the ore petrologist seeking to interpret observed data in terms of a particular physical and chemical environment of ore deposition. These two problems are the sequence of formation of sulphide minerals (commonly designated the paragenetic sequence) and an elucidation of the range of temperatures and pressures which existed during crystallization. The object of this paper is to make such an interpretation of the copper mineralization of the Mt. Lyell district, Queenstown, Tasmania.The following abbreviations are used in this paper:py = pyrite, cp = chalcopyrite, en = cubanite, bn = bornite,cc = chalcocite, cv = covellite, dg = digenite, id = idaite,po = pyrrhotite, v = sulphur vapour.GEOLOGICAL SETTING AND MINERALIZATIONThe general geology of the Mt. Lyell district is well known through the recent work of Wade and Solomon (1958). The host rocks are a series of quartz-chlorite-seri-...

Jan 1, 1963

By Steve Kral

When the price of gold cracked the US$9.60/g(US$300/oz) mark last year, the gold-mining industry began to crank up again. This followed several years of gold prices that had languished in the mid-200s. Existing mines increased production and mines that had lain dormant for many years were getting second looks. The United States still produces a large amount of gold. But not much of the new production is coming from that country. Instead, strict environmental regulations still have companies wary of trying to invest the millions needed to start a new mine or expand existing ones. And after years of studies and negotiations between legislators, environmental interests and the mining industry, the United States still has not crafted a new mining law.

Jan 1, 2003

The title of “the world’s biggest volume-produced hydraulic breaker,” that was held for more than a decade by the Atlas HB 7,000, changed hands with the launch of Atlas Copco’s HB 10,000 at bauma 2007. A service weight of 10 t (11 st) and up to 50 percent higher productivity represent major steps toward a new market segment: the use of hydraulic breakers as cost-efficient production machines for primary breaking and as a true alternative to drilling and blasting. The HB 10,000 has all the technical features developed by Atlas Copco for its hydraulic breakers and includes: StartSelect — the breaker’s start-up and shut-down behavior can be adapted to the conditions. AutoControl that ensures an optimized balance of impact energy and impact frequency to maximize percussive performance. Auto-Control also reduces blank firing force and controls energy recovery. PowerAdapt — if oil pressure is too high, the breaker shuts down automatically. This prevents downtime and is particularly useful when breakers are used on different carriers. DustProtector II — a combination of multiple strippers prevents abrasive rock dust and foreign bodies from penetrating the lower breaker section. Conti- Lube II — the automatic lubrication unit guarantees optimal lubrication of the breaker at all times.

Jan 1, 2007

By H. L. Retcofsky

Carbon-13 nuclear magnetic resonance (18CNMR) spectra of nine 2-substituted pyridines, seven 3 -substituted pyridines, and nine 4-substituted pyridines have been obtained and analyzed. Substituents included both electron-releasing groups and electron-with hawing groups. Substituent effects on the magnetic shieldings of the ring carbons, except for those in the 2-positions of 2-substituted pyridines, were found to be quite similar to the effects reported for the monosubstituted benzenes, Thus, at least to a first approximation, the two classes of compounds have similar shielding mechanisms. Shieldings of the carbon atoms in the 5-positions of 2-substituted pyridines and those in the 6-positions of 3-substituted pyridines were found to reflect electron release or withdrawal by substituent groups, The pyridinium cation and the compounds 2,2'-dipyridyl and benzonitrile were also investigated.

Jan 1, 1969

By O. M. McRae

The Courtland-Gleeson area is in Cochise County about 15 miles east of Tombstone in southeastern Arizona. Rocks exposed in the area range in age from Pre-cambrian to Quaternary. The Precambrian is repre-sented by the Pinal schist. Paleozoic rocks include the Cambrian Bolsa quartzite and Abrigo limestone, Mississippian Escabrosa limestone, and the Permo-Carboniferous Naco Group limestones. Rocks believed to be of Triassic and/or Jurassic age include the Copper Belle monzonite porphyry, Turquoise granite, and Gleeson quartz monzonite. The Cretaceous is represented by andesitic volcanics and various sedimentary rocks. Tertiary rocks include the intrusive and extrusive Sugarloaf quartz latite porphyry and numerous dikes of various rock types. Quaternary conglomerates cover the northern and eastern part of the area. The geologic structure is extremely complex. All rocks as old as early Tertiary have been involved in either tilting, normal faulting, high angle reverse faulting, imbricate thrusting or folding and overfold-ing. Major deformation was initiated during the first half of the Tertiary. Northeast-southwest compres-sional forces caused thrust plates containing lower Paleozoic rocks to override Cretaceous rocks. Subsequently, two large slide blocks of lower Paleozoic rocks, acting under the influence of gravity, moved eastward. The imbricate structure and the gravity slide blocks were then broken by late Tertiary normal faults. INTRODUCTION The Courtland-Gleeson area, or Turquoise Mining District, has long been recognized as an area of extreme structural complexity. Gilluly 2 referred to the entire district as a "gigantic thrust breccia". In 1962, Bear Creek Mining Company completed a two year program of detailed geologic mapping supported by exploration drilling. The purpose of this paper is to present some of the results of this investigation and to provide a structural interpretation based on these results. The geologic map that accompanies this report is generalized and shows only the major and significant features. The area was initially mapped on aerial photographs on a scale of 1 in. equals approximately 500 ft. These data were transferred to a planimetric base using a vertical sketch master. LOCATION The Courtland-Gleeson area is in central Cochise County, about fifteen miles east of Tombstone, and about twenty-two miles northeast of Bisbee in southeastern Arizona (Fig. 1). The area is readily accessible over graded gravel roads from both Tombstone and Elfrida. GENERAL GEOLOGY Rocks exposed in the area range in age from Pre-cambrian to Quaternary. wilson3 and Gilluly2 have published very detailed descriptions of the principal rock units exposed in the area. Only a summary description is provided in Table I. A great number of previously unmapped narrow Tertiary dikes and small irregular masses of hornblende andesite porphyry, lamprophyre, and aplite intrude the Gleeson quartz monzonite in the western part of the map area. The scale of the map prohibits showing them. The aplite dikes are related to, and bear the same structural relationships as, the Sugarloaf quartz latite dikes found in this area. For that reason, and because both the hornblende andesite porphyry and the lamprophyre are post-mineral and post-thrusting, their omission from the map is not considered significant. Because so many of the contacts in the district are fault contacts, because bedding faults appear to be prevalent but are difficult to recognize and map, and because igneous intrusions are so common throughout the sedimentary section, it is virtually impossible to measure an exact total thickness of any of the sedimentary rock units. Nevertheless, neither the field mapping program nor the diamond drilling provided any basis for suspecting that the thicknesses of the sedimentary units are significantly greater or less than what might be inferred from surrounding districts.

Jan 1, 1967

By Mech B

This paper gives a general description of mining practice at The Zinc Corporation Ltd., Broken Hill, New South Wales.The basic mining methods are those which have been common in Broken Hill for many years and have been well described in previous Proceedings. The main object of this paper is to indicate developments which have occurred in recent years and to describe changes in layout, mining methods and equipment which are taking place at present.The following headings have been adopted: History Geology and general characteristics of the orebodies, Geology, The lead lode, The zinc lode, General characteristics, Ore reserves, General mining method, Exploration and diamond drilling, Shafts and shaft sinking, Main shaft, Old main shaft, Block 5 shaft, New upcast airway, Development, Level interval, Level layout, Driving and crosscutting, Winzing, Rising, and Stope preparation.

Jan 1, 1946

By H. E. Lee, D. Ingvoldstad

AT Bunker Hill the original charge storage and preparation system was installed in 1917 to accommodate lead-silver gravity mill products. Only minor tonnages of wet fines such as vanner and flotation concentrates were received. Charge flux and diluent requirements were provided by an ample supply of siderite middlings and coarse lime-rock. While oversize material was crushed through %-in., the use of roll crushers in series resulted in a more or less granular, free-running charge of adequate porosity. Under such conditions, receipts could be proportioned directly from receiving bins, and suitable blending was obtained by passing the resultant layered composite through a small Stedman disintegrator. This elementary system served well for production and smelting of an extremely lead-rich sinter, in the low column blast furnace. Here sinter physical quality is less critical, and appreciable quantities of raw flux and oxidized ore may be charged directly to the blast furnace without seriously impairing furnace capacity. Prior to 1938 the relative proportions of zinc receipts were low and extraneous flux requirements at a minimum. However, subsequent war-inflated zinc demands brought marked increase in fine concentrate and slimy zinc leach residue receipts and an abrupt introduction to smelting a more refractory zinciferous charge. The higher temperature demands of the more refractory zinciferous charge required a higher smelting column and the higher column, in turn, rendered the blast furnace less receptive to improperly prepared feed. Inadequate presinter processing facilities prevented the production of acceptable sinter, and blast furnace production declined to 50 pct of former capacity. In view of a prevailing contention among lead metallurgists as to the deleterious action of high zinc slag on blast furnace capacity, it was natural to overstress this factor and to concentrate on possible changes in furnace design. Another interpretation was that primary correction should be sought through expanded sintering facilities. This divergence of opinion, together with the extreme material shortages of the 1940's, delayed corrective

Jan 1, 1957

By G. L. Oldwright, Virgil Miller

"The data presented in this paper were collected at the smelter of the Consolidated Mining & Smelting Co. of Canada Limited, Trail (Tadanac), Brithish Columbia. The authors are greatly indicated to S.G. Blayrock, vice president and general manager; James Buchman, smelter superintendent; and the staff members mentioned in Report of Investigation 3243. The authors are exceedingly grateful to George Murray, assistant smelter superintendent, for his keen interest, suggestions, and help in carrying out this investigation.INTRODUCTIONThe methods of charign the blast furnaces at Toole and Kelloggs were noted in Report of Investigations 2957 and 3094 respectively. Report of Investigations 2957 cited (4 to 9 inclusive) Hofman's Metallurgy of Lead (p. 226) and the work of A.S. Dwight, Thompson and Sicka, the staff of the Engineering and Mining Journal, and L.D. Anderson, N.F. Collins, in The Metallurgy of Lead (Chas. Griffin, London, 1910) also gives (pp. 247 254) the principles that he believes govern the successful charging of the blast furnace."

Dec 1, 1934

By F. E. Lathe

INTRODUCTION THE present study, based largely upon phase equilibrium diagrams and other theoretical considerations but nevertheless addressed primarily to the practical metallurgist, has been undertaken with a view to discovering what light can be thrown upon the role of alumina in slags. According to Liddell (23), "alumina apparently acts as .a base if much silica is present, as an acid if the silica is low, always as a nuisance." Newton and Wilson (26) state that .alumina "is never added intentionally, as it makes the slag viscous, and is generally an undesirable constituent of slags". Camp and Francis (3) sum up their views by saying, "alumina is seldom used intentionally as a flux, but it is present in nearly all raw material, hence unavoidable". One has only to read The Function of Alumina in Slags, by Henrich (I3), and the very extensive discussion that followed the presentation of his paper, to realize that, before the days of phase equilibrium diagrams, it was a very serious question indeed as to whether alumina should be calculated as a basic, acid, or neutral constituent. Opinions then differed widely, as well they might; today, even though no categorical answer can be given to the question raised, the function of alumina can be at least partly clarified by a study of the fundamental work done by the Geophysical Laboratory in Washington and by certain universities in both America and Europe. It will be a source of gratification to Canadian metallurgists and ceramists to know that work of this type is now under way in the recently organized Physical and Crystal Chemistry Section of the Mines Branch, Ottawa, and that results of practical value have in fact already been obtained.

Jan 1, 1951

By Frederic Benard

PRIOR to 1936, the Ontario Refining Co. received all incoming blister copper from The International Nickel Company's smelter in the usual form of 460-lb. cakes, or slabs. These were received in open cars in lots of 250 pieces. At the refinery the cakes were unloaded onto narrow-gauge cars, for convenient handling and pickup by charging cranes. In March 1936, an investigation was started on the feasibility of transferring converter copper in the molten state from the smelter to the refinery anode furnaces, a distance of 1 ¼ miles. Although common in steel practice, the transportation of blister copper in this form had not previously been attempted and a preliminary study of the various factors involved was therefore necessary. For this purpose, a series of experiments was made in which molten copper, removed at different stages during the furnace cycle, was held in a small portable holding furnace. This vessel was essentially a refractory-lined steel cylinder provided with ports for filling and emptying, heated by an oil burner. Dimensions of the steel shell were 3 ft. 10 in. diameter by 7 ft. 3 in. long, and thickness of refractories depended on the design and combination used for the particular experiment. The vessel was filled with approximately 2 ½ tons of copper at a predetermined temperature, the lining having been preheated to a definite point by means of an oil burner. All openings were well luted and temperature readings were made every 15 min. by means of an immersion-type thermocouple. In this manner the rate of heat loss resulting with different refractory design could be developed. The ratio of exterior surface to weight of metal was taken into consideration in comparing the experimental results with what might be expected for a full-sized unit, and observations were also made on type and degree of slag accretion. It was not possible to get as much information on this latter point as desirable, but all evidence showed that the problem would be control of slag build-up rather than attack on refractories. From the information derived, and in consultation with the engineering staff of the supplying company, an order was placed for the first

Jan 1, 1938

By J R. Lang, J K. Mortensen

The Canadian Cordillera contains numerous classic porphyry deposits and several unusual subtypes, including the alkaline suite of porphyry Cu-Au deposits and the Tombstone magmatic suite and associated Au¦W deposits. The alkaline suite formed in collisional settings in island arcs whereas the Tombstone suite was emplaced in an active fold and thrust belt in a continental arc. In addition to different regional settings, these suites differ in the type of underlying basement, metallogeny, and the styles of mineralization. Both magmatic suites were emplaced over short intervals, probably in response to specific tectonic events. In the case of the alkaline suite, the tectonic event promoted magmatic processes suitable for the formation of porphyry Cu-Au deposits. The tectonic environment is less well constrained for the Tombstone suite, but the result was the formation of distinctive porphyry and intrusion-related Au¦W deposits.

Jan 1, 1995

By H. J. Rose, H. H. Lowry

Considerable information on the organization of German fuel research and recent developments was obtained and published in several combined Intelligence Objectives Sub-Committee Reports. This material, although avail- able in the initial reports, has never been consolidated, so that it may not have come to the attention of many readers. This report gives a summation of the authors' observations at six different research laboratories.

Dec 1, 1947

By Robert Jakiel

The following paper is being presented to provide an understanding of the Deep Soil-Cement Mixing (DMM) performed at Contract C09A7 at the Fort Point Channel Site (FPC), for the I-90/I-93 Interchange of the Central Artery/Tunnel Project (CA/T), Boston, MA. The paper is written as a summary of the DMM from the DMM Contractor's perspective. The summary provides technical information and practical observations that are currently considered to be state-of-the art knowledge within the soil mixing industry. The observations and information are being provided by Robert L. Jakiel, Chief Engineer of SMW Seiko, Inc., who was the DMM Project Manager and Project Engineer for the A7 Joint Venture at FPC. The DMM was started in April of 1996 and completed in December 1999. The various acronyms and terminology used to describe the soil mixing are found in a section at the end of the paper.

Jan 1, 2000

By V. E. Erwin, W. W. Adams, E. V. Walters

"Increased production of explosives in the United States in 1933 compared with 1932 is shown by statistics compiled by the Demographical Division, Health and Safety Branch, United States Bureau of Mines. The figures relate only to explosives used for industries purposes, such as mining, quarrying, and road building, and do not cover nonindustrial explosives, such as ammunition or fireworks. Industrial explosives include black blasting powder, permissible explosives, 5 and high explosives other than permissibles figures in the tables of this report were compiled from reports covering sales by the individual companies manufacture of explosives in the United States in 1933. Because of the close agreement among the several series of figures, the quantity of explosives sold is considered as reflecting production and consumption, and the three terms ""sales"", ""production"", and ""consumption"" are used interchangeably in the discussion unless otherwise stated.Of the principal industries that use high construction operations accounted for the largest percentage of increase in consumption during 1933; metal mining and quarrying also used more of this class of explosives than in the previous year. Coal mining is the chief consumer of permissible explosives; the figures for 1933 showed that bituminous-coal mining used a larger quantity than in 1932, and that anthracite mines also showed a small increase. Although a net increase of less than 1 percent in consumption was reported for black blasting powder, large increases in use of this class of explosives were reported for metal mining, miscellaneous types of work, and bituminous-coal mining. (See table 1.)"

Nov 1, 1934

By Xu Youzai

Static loading teets of five nodular piles and four non-nodular piles were performed in Tianjin soft clayey soil in which measurements of axial force and movements were made. Distribution of shaft resistance and load-movment curves for pile head and pile toe are presented in this paper. The applicability of nodular piles to soft soil and their effectiveness are also discussed. Based on the comparison, it is concluded that nodular piles have an advantage over non-nodular piles mainly in contri­bution to shaft resistance. Dynamic testing was also conducted through R. P. T. for evaluating the service load of tested piles.

Jan 1, 1991

By Vincent Tirolo

Two separate secant pile cofferdams were constructed as part of an extensive rehabilitation and modernization of the New York City Transit's Lexington Avenue/Third Avenue IND Station at 53rd Street in Manhattan. Major high rise structures and outpatient hospital facilities bordered the site. The roadway is an important east-west corridor in mid-Manhattan. In order to perform the construction of new escalator and elevator shafts over 250 linear feet of secant wall was installed to the top of rock or to the existing subway roof. Much of the secant wall was constructed from below a temporary roadway decking system using a low headroom rig. The roadway decking system was supported on shallow spread footings. The secant piles were drilled using crawler mounted hydraulic rotary drill rigs. The secant wall provided a watertight, rigid cofferdam that minimized settlement and other disruptions to existing structures and utilities. During later stages of the project the secant wall also supported the roadway decking system.

Jan 1, 2003

To the industrial geologist, as wen as to the general or historic geologist, the possession of a reliable key to the true order or sequence of the stratigraphy or position of the various upper rocky envelopes of the earth's crust, is, equally, a desideratum of the utmost importance. Of similar value to the two groups of students is the possession of facts which throw light upon the relationships which subsist between the puccessive rock formation of different countries, especially between countries lying close to each other, or within the same great geographical division.But there is necessarily a fundamental distinction which marks the respective limits of the field of observations of the industrial geologist, and the purely historic interest of the general geologist. The former has a more definite though less extensive scope. The scope of the latter is wide and indeterminate. In short, the observations of the industrial geologist are, 'from a commercial or economic point of view, of a more practical character, and are, therefore, intentionally restricted to the study of all geological questions which throw light upon the rocks which yield products of economic value and only include the study of the character and history of other rocks, in so far, as they afford aid to the more perfect comprehension of the best manner in which materials of economic value are likely to be sought, and the best means whereby these products may be secured for the material advantage of the community. The motive of the general geologist-in most cases-is a love of the study of some particular branch or province of the geological field, and the fascination of opening a new volume in nature's library, and the hope of extending the realm of knowledge, however slight, are often sufficient, as a motive, to enlist the energy and life's devotion of the true brethren of the hammer, irrespective of considerations regarding the commercial utility of the pursuit.