Search Documents

By Jon R. Maki

"EVTAC, an iron ore mine in Minnesota, had trouble meeting the customer’s pellet silica requirements. In addition, the mine plan was moving towards a lower grade ore and funding was not available for plant improvements to compensate for the change in ore or improving quality. Small changes to optimize various processing equipment resulted in significant improvements in both quality and productivity; for example, productivity on one mill line increased by 10% while producing lower silica concentrate. This paper will provide the methodology that allowed EVTAC to improve quality and productivity through process optimization with little capital investment.INTRODUCTION EVTAC, an iron ore mine in Minnesota, had trouble meeting the customer pellet silica requirements. In addition, the short-term mine plan was changing to a lower ore grade. Because of limited funds, EVTAC did not have the capital for investing in the plant to compensate for the ore change or to make improvements to lower product silica levels. Small changes to optimize process equipment resulted in significant improvements in quality and productivity; for example, one mill line feed rates increased by 10% while also producing a higher quality concentrate. These changes were sufficient enough to allow the mine to lower the target ore grade beyond their initial goal. At one time, a $3M flotation facility was considered as a way to meet quality with the new ore grade. However, the process changes were able to accomplish the same silica reduction with roughly a $50,000 investment in VFDs for sump controls. This paper will discuss some of the modifications that allowed EVTAC to meet the quality and production objectives with little capital investment. It also discusses the methodology used to make these process improvements."

Jan 1, 2014

By V. K. Kuppusamy, M. Holuszko

"Lamps and lighting products are the most commonly used electrical products around the globe. With the improvement in lamp technologies, lighting products have grown complex and hence require an improved recycling process. The LED lamps consist of various valuable metals such as iron, copper, aluminum, chromium, silver, and gold, as well as non-metals such as glass, plastics, and fibers. In addition, there are also traces of hazardous substances such as lead, arsenic, and mercury. A major step in the recovery process is size reduction, and researchers have suggested that up to 40% of the total valuable material is lost during the shredding and grinding processes. SELFRAG is a high voltage selective fragmentation comminution technology that uses high voltage pulses in a water medium to efficiently separate the metals at a coarser size without generating many fine particles. It has been proposed that during the fragmentation process of electronic waste (e-waste), the metals can be separated without fine grinding. This research considers the applicability of high voltage pulse fragmentation for LED lamps. Eight different types of LED lamps were processed through the SELFRAG unit at varying pulses to study metal liberation. The product obtained was characterized for metal liberation, metal grades, and liberation analysis. The specific energy consumption for this size reduction process was also monitored. INTRODUCTION Lamps and bulbs are the most commonly used electrical products in homes, offices, industrial operations, and streets. According to Energy Star research (2006), an average US household has more than 40 sockets for light bulbs and consumes approximately 2100kWh every year for lighting. The development in lamp technology has pushed the boundary for newer products. The LED lamps have been taking over the market from the incandescent bulbs and compact fluorescent lamps (CFL). According to the US Department of Energy (2012) and myLEDlight.com (2007), LED lamps have several benefits over other lamps. LEDs produce light hemi-spherically, which increases their efficiency in directional light emission. It has higher breakage resistance from vibration or transportation. LED lamps use up to 90% less power than incandescent bulbs thus making them highly energy efficient; They have a longer lifespan, lasting 10 times longer than a CFL and 133 times longer than the traditional incandescent bulb. Because of all the benefits, Smallwood (2014) suggested that the market of LED lamps will grow to $12.2 billion by 2018."

Jan 1, 2018

By Bo Forsman

METAFORA is a simulation model for determination and evaluation of strategies for operating loader/truck systems in mining. A specific version of METAFORA was used to evaluate the haulage system at Solider Mineral's Aitik mine in northern Sweden, one of the largest open pit mines in Europe with a production of about 11.5 Mtpy (about 34000 tpd) of copper are. A production level of 34065 tpd was estimated by simulation runs with METAFORA. Using METAFORA's dispatch rules (Fixed Dispatch, Maximize Trucks, and Maximize Loaders), the truck/shovel system in the Aitik mine was simulated for evaluating alternative dispatch control strategies. The Maximize Trucks rule gave about the same total production (ore + waste) as the Fixed Dispatch rule but a 9% higher ore production. The Maximize Loaders rule gave the lowest production. The marginal truck capacity decreases with increasing number of trucks serving the same loader due to increasing waiting times. In Aitik mine the low crusher capacity results in long dumping times. If the dumping time at the crusher could be halved, the ore production would increase by 14%. The paper indicates that the use of software like METAFORA can result in a substantial reduction of time, effort and cost in shovel/truck system design and evaluation.

Jan 1, 1992

By S. F. Diehl

Weathered mine waste consists of oxidized primary minerals and chemically unstable secondary phases that can be sources of readily soluble metals and acid rock drainage. Elevated concentrations of metals such as Cd, Cu, Fe, Mn, Ni, Pb, and Zn are observed in deionized water-based leachate solutions derived from complex sedex and Cu-Pb-Zn mine wastes. Leachate (USGS FLT) from the Elizabeth mine, a massive sulfide deposit, has a pH of 3.4 and high concentrations of Al (16700 ug/L), Cu (440 ug/L), and Zn (8620 ug/L). Leachate from the sedex Faro mine has a pH of 3.5 and high concentrations of Al (2040 ug/L), Cu (1930 ug/L), Pb (2080 ug/L), and Zn (52900 ug/L). In contrast, higher-pH leachates produced from tailings of polymetallic vein deposits have order of magnitude lower metal concentrations. These data indicate that highly soluble secondary mineral phases exist at the surface of waste material where the samples were collected. Sulfide minerals from all sites exhibit differential degrees of weathering, from dissolution etched grain rims, to rinds of secondary minerals, to skeletal remnants. These microscale mineral-dissolution textures enhance weathering and metal leachability of waste material. Besides the formation of secondary minerals, sulfide grains from dried tailings samples may be coated by amorphous Fe-Al-Si minerals that also adsorb metals such as Cu, Ni, and Zn.

Jan 1, 2011

By B. K. Gorain

"Mining of low grade deposits along with the necessity to design and operate process plants requiring high throughputs presents unique metallurgical environmental and sustainability challenges that need to be addressed to reduce project risks, improve project economics and to sustain the profitability of operations over the life-of-mine.Some of the key challenges include poor recovery of valuables and concentrate quality issues due to complex mineralogy and high ore variability, water scarcity and quality issues, high energy costs, complex environmental issues including tailings management, high capital and operating costs, worldwide constraints on resource availability, complicated regulations in emerging economies, changing demographics of mining operations with ever-changing cultural or community issues and the urgent need for a better assessment of project viability to reflect the dynamics of present mining scenario. Developing breakthrough solutions to these problems is the key to success of any new project and maintaining profitability of a mining operation. An integrated multi-disciplinary approach to problem solving is crucial along with the need for a more lateral thinking, strategic partnerships and collaboration involving the right players. This paper presents some of the key findings based on experiences from a large number of challenging projects and operations focused on solving complex metallurgical problems.IntroductionThere is a plethora of challenges in developing new ore bodies. The metallurgical complexity of these deposits has increased significantly due to the need for mining lower grade ores along with the presence of deleterious elements that have environmental and processing implications. In addition, many of the mining projects are capital intensive due to high throughput requirements to be economical along with the need for building infrastructure due to remote locations, while operating costs steadily increase due to high reagent, energy and labour costs, increased state royalties and community obligations, to name a few of the key factors. There is also scarcity of water in many regions requiring the use of sea water or brackish water, which has both environmental and metallurgical implications. The shortage of qualified technical manpower adds significantly to the woes of many mining companies. Considering these multiplicity of challenges, it has become imperative for many mining companies to be innovative in addressing these issues."

Jan 1, 2015

By W Polkowski, M Tangstad, M Wallin, J Jiao

Fe-26Si-9B (wt per cent) alloy has been identified as a potential high-temperature phase change material (PCM) due to its attractive properties, such as its high latent heat of fusion and low volumetric change during solid/liquid transition. For the successful utilisation of this alloy into thermal energy storage (TES) systems, the development of a cost-effective production method is essential. Presently, the Fe-26Si-9B alloy is produced by mixing FeSi alloys with either pure boron element or FeB alloys. However, the use of pure boron is financially prohibitive, and the carbothermic reduction results in high greenhouse gas emissions and high energy consumption in the production of FeB alloys. In this regard, our study proposes a silicothermic reduction method to produce Fe-26Si-9B PCM by using FeSi alloys and B2O3-based oxides. Accordingly, the influence of various parameters on the production process was investigated, including operating temperature, holding time, B2O3 content in the added oxides, and initial Slag/Metal (S/M) ratio. Based on the experimental results, the optimal parameters for producing FeSiB alloys with over 9 wt per cent boron were determined. Consequently, it was documented that the FeSi alloys and the added oxides enriched with 50– 65 wt per cent B2O3 should be subjected to temperatures ranging from 1550–1650°C, maintain an initial S/M ratio exceeding 1, and ensure a holding duration beyond 1 hr. Moreover, the energy consumption of this process was estimated to be ~1.86 MWh/t metal and the mass loss was lower than 7 per cent. Therefore, silicothermic reduction offers a sustainable approach for producing FeSiB alloys with a boron content above 9 wt per cent.

Jun 19, 2024

By Wittenberg J. C, Reid A. F

A method is described for the rapid and effective production of polished section mounts of ore and mineral particulates to the standards required for automated image analysis. This requires mounting without segregation of particles by mass or density, and it is also preferable to avoid having particles in contact so that they can be recognised as individuals. To achieve this, the particle samples are first split to an appropriate degree in a rotary riffle, and the sub-sample mechanically diluted and thoroughly mixed with an inert filler of the same size range as the particles. Just sufficient epoxy resin is added to make the mixture fluid. During setting, the ore particles are mechanically supported by the inert filler particles, thus maintaining the particles in a random three-dimensional distribution. A rapid two-stage grinding process, based on the successive use of 600 mesh silicon carbide and 1200 mesh (10 um) corundum on cast iron plates, is followed by three stages of mechanical diamond polishing on cloth laps. Hand polishing is entirely avoided, as is the use of papers.

Jan 1, 1984

The importance of timbering, not only from a financial point of view but from an actual mining point of view, is so often overlooked or slightly glossed over by the average expert and investor, that I have thought it would prove interesting to go into the matter and to invite discussion upon the subject. We will first take small veins, or reefs as they are termed in some mining countries; and by small veins it is intended to denote fissures from a few inches to three feet. The ore body is supposed to be confined within well defined walls free from gangue matter, unless the casing can be defined as such. Now, if the walls are smooth and moderately hard, no timbering is required other than the stulls, which are braced from wall to wall in order to form platforms or stages to stope from. Should the reef from wall to wall prove payable, or should the vein be of a character to prohibit cleaning or sorting; and it be determined to send the whole of the stone to the, reduction works, the stuUs should be left in place until the section or block of ground is worked out, in order that if a weak spot in the walls (especially the hanging) occur, it would be possible, without any particularly extra expense or difficulty often times accompanied by danger to brace and secure the slabs. After the block became entirely stoped, it would pay where labour was cheap to remove the majority of timbers to stull another section.

Jan 1, 1901

Owing to the increased consumption of sulphuric acid; Australian manufacturers have, from time to time, been seeking for a satisfactory source of sulphur that would make them independent of foreign supplies.Some years ago a considerable amount of acid was obtained from the roasting of Spanish pyrites. This ore, in 1913 or thereabouts, cost 16s. per ton f.o.b. Huelva, and freight to the eastern seaboard of Australia was about 20s. per ton. As the ore contained 48% to 50% of available sulphur, it was costing roughly 9d. or 10d. per unit, and, in addition, the cinder, after roasting, was a product of considerable value to smelters, containing as it did a high percentage of iron suitable for fluxing, and appreciable values in silver and gold.

Jan 1, 1925

By H. L. Anthony, A. C. Richardson, G. D. Coe

"INTRODUCTION The Warrior View mine of the Seaboard Coal Corporation is located in Tuscaloosa County on the Warrior River about 14 miles northeast of Tuscaloosa, Ala. The Brookwood bed at this point yields a coal with fair coking qualities, and the product from neighboring mines on this bed has been used for the manufacture of blast furnace coke. The output of the Warrior View mine, however, is used exclusively for domestic and steam-raising purposes.This paper continues the series° of reports on the washability of Alabama coals which are based upon the study of coal preparation in Alabama now being conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal mining companies. This paper contains screen-sizing and float-and-sink tests of a representative sample of run-of-mine coal, and flakiness and crushing tests on certain sizes.Published information on the Brookwood bed is very meager. Fieldner6 gives the proximate and ultimate analyses for a number of seam samples taken from representative mines working this bed. Gandrud and Britton7 show sections of this bed taken at Searles, Ala. They also give the specific gravities of the coal, the bone, and the shale partings.Table 1 give the proximate and ultimate analyses for the 3/4 to 3/16 inch size of raw coal. Table 2 gives the sulphur content and the ash fusibility temperatures of the float-and-sink fractions for this same size. The character of the coal is very uniform throughout the range of sizes produced and, as it was not convenient to have these analyses on all sizes, this size was chosen as being representative of the coal. From the information available it is evident that the coal preparation problem is restricted to one of ash reduction.SAMPLING AT THE MINEAt the Warrior View mine the run-of-mine coal is dumped from the mine cars upon a 3-inch grizzly. The oversize is crushed in rolls set at 24 inches and joins the undersize before being elevated to the raw-coal bin ahead of the jig. The sample was caught at the point where elevates discharges into the raw-coal bin, by taking a proportional amount of the coal at 10-minute intervals over the period of a day's run, The total sample amounting to 2.7 tons was shipped to the laboratory at Tuscaloosa for the washability studies."

May 1, 1932

By Todd M. Ruff

The majority of fatalities that occur in road construction work zones in the United States involve a worker being struck by a piece of construction equipment or other vehicle. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health, in cooperation with the Washington State Department of Transportation, is evaluating methods to decrease these accidents. One such method uses devices that assist equipment operators in monitoring blind areas around the equipment to prevent collisions with workers on foot or other objects. Several cameras and sensor systems are available for this application, and a study was conducted to evaluate these systems on various trucks used in road construction and maintenance. Tests were conducted using sanding trucks during the winter months, which allowed researchers to investigate the effectiveness and limitations of various technologies under the most extreme conditions. Tests were also conducted using dump trucks during the warmer months to study the effectiveness of the systems in highway work zones. Results show that many difficulties arise when using camera and sensor systems in cold, snowy climates. And, while the operation of these systems is more reliable during the warmer months, challenges still exist in using them on equipment in crowded work areas.

Jan 1, 2004

IN 1949 the Government Printing Office issued Bureau of Mines Bulletin 468 3 and previously (in 1948) Bulletin 467 4 as part of the program under the Synthetic Liquid Fuels Act of April 5, 1944 (30 U. S. C., 321-325, and amendments). The two bulletins, relating to oil shale and its products, were published to present abstracts of all patents in this field from 1845 to 1945 5 or before the Synthetic Liquid Fuels Act was passed. Also, as part of this program, bulletins were published on patents relating to the pressure hydrogenation of coal e and the Fischer-Tropsch synthesis.7 The Synthetic Liquid Fuels Act was not extended beyond April 1955, but it inspired much increased activity in the field of oil-shale research, and many patent applications were filed. It is the purpose of this bulletin to abstract the patents issued in the United States, the United Kingdom, and Europe from 1946 to 1956, inclusive. A few older patents omitted in the previous bulletins have been included.

Jan 1, 1959

By Jon C. Volkwein

In This Chapter [Instruments for measuring dust How to calculate the amount of dust from a source How to get a valid concentration measurement Sampling to assess control technology effectiveness] When there is more than one source of dust, sampling may be required to find which dust sources are most significant. Then, efforts to reduce dust can be concentrated where they will have the most impact. This chapter explains how to perform dust source sampling. It describes two kinds of instruments that are available and discusses their limitations. It explains how environmental variables such as concentration gradients, dust dilution, and production changes can impact dust measurements. It also suggests practical ways to improve the validity of dust source measurements under adverse conditions, such as high-velocity airflow or the presence of water mist in the air. [Dust source sampling at coal mine longwalls and at tunnels is more complicated. Chapters 3 and 7 have more information on sampling in those circumstances.] TWO KINDS OF INSTRUMENTS FOR MEASURING DUST Gravimetric samplers. The conventional gravimetric sampler is a good device for measuring dust because it is the instrument used for compliance measurements. This dust sampler consists of an air pump, a small cyclone that separates out the respirable size fraction of the dust cloud, and a filter to collect the respirable dust. In coal mines, the Mine Safety and Health Administration (MSHA)-approved gravimetric sampler uses a 10-mm Dorr-Oliver cyclone operating at an airflow of 2.0 L/min [30 CFR78 74 (2002)]. A correction factor of 1.38 is applied to make the results consistent with the U.K. MRE sampler, the instrument on which the 2.0 mg/m3 coal dust standard is based.

Jan 6, 2003

By Christopher Mark

The first International Conference on Ground Control in Mining opened with the topic of pillar design. Two classic papers were presented, one by Bieniwski and the other by Wilson. Unfortunately, the two methods were so radically different from each other that it was nearly impossible to reconcile them. Adding to the confusion were the many other pillar strength formulas (such as the Salamon-Munro, the Holland-Gaddy, and the Obert-Duvall, just to name a few) that were also available. Little wonder that discussions of pillar design in those days often ended with anguished cries of ?but which formula is the right one?? The past 25 years have seen substantial progress in the science of coal pillar design. Indeed, one testament to the improvement is the relative scarcity of papers on the topic at recent Conferences. Two factors have been largely responsible for the progress that has been made. The first has been the collection of large data bases of actual case histories of pillar performance in a variety of settings, from shallow room-and-pillar mines through deep cover longwalls. These have made possible the development of empirical design procedures that are closely linked to real world experience. The second important factor is the development of sophisticated computer models that can accurately simulate pillar behavior and roof/pillar/floor interactions. Together, these two lines of research have led to a new understanding of pillar mechanics that identifies three modes of pillar failure: ? Sudden, massive collapse, accompanied by airblast, for slender pillars (width/height<4) ? Squeezing, or slow, non-violent failure, for most room and pillar applications (4<w/h<10) ? Entry failure or bumps for deep cover and longwall applications (w/h>10) It is particularly satisfying that the insights gained from numerical models broadly support those obtained from the empirical studies. While far less controversial than in the past, pillar design problems continue to arise. One recent example is pillar design for highwall mining. NIOSH has just released a software package, called ARMPS-HWM, which employs a number of modern pillar design concepts. Since highwall mining web pillars are long and slender, the greatest danger is that of a sudden collapse. ARMPS-HWM suggests two possible prevention strategies, one which concentrates on the SF of the webs, and the other which creates a ?pressure arch? using properly sized barrier pillars. The paper will close with a discussion of some current needs in coal pillar design, including: ? Updating older empirical methods, such as ALPS, where changes in technology (new types of roof support, more demanding ventilation requirements, faster retreat rates) may have made some of the original case histories obsolete. ? Methods for determining site-specific coal strengths, focusing on bedding plane strength and other factors that may effect confinement, as input for both empirical and numerical design. ? Improved methods for evaluating coal pillar performance for environmental issues, such as surface subsidence and hydrologic impacts, which consider such factors as depth, w/h ratio, water immersion/drainage, and time dependent seam strength.

Jan 1, 2006

By Frank Callanan

The Ameristar Casino expansion project included the design and construction of a 25-story hotel and 9-story parking structure expansion. The site is located in a floodplain on the banks of the Missouri River in Saint Charles, Missouri, where the underlying soils are potentially liquefiable. The geotechnical engineer performed subsurface exploration and analysis, which included site-specific seismic response and liquefaction, and provided geotechnical design recommendations. In the event of an earthquake, post-liquefaction settlement was calculated to be approximately 14 inches. Additional project constraints included wetlands protection, construction adjacent to the existing facility, flood protection and river bank stability. Because of the liquefaction issue, the geotechnical engineer consulted with a specialty geotechnical contractor on ground improvement methods. This consultation led to a proposal to eliminate deep foundations from the design and support the structures on shallow and mat foundations. The geotechnical engineer assisted the design team with foundation design analysis and value engineering assessments. Together with the project team, the geotechnical engineer used the data to evaluate foundation options and construction methods to overcome the site challenges and concluded that ground improvement was the optimum course of action. Because of the nature of the site constraints, a number of ground improvement methods were needed. The geotechnical engineer evaluated the methods proposed by the geotechnical contractor and provided the technical specifications for the ground improvement bid package, which included vibro-compaction, compaction grouting and micropiles. The ground improvement allowed for the use of shallow foundations (mat and spread footings), which provided the client with significant time and cost savings over the deep foundation alternatives.

Jan 1, 2009

With the exhaustion of orebodies close to the main haulage shaft of the Emperor mine, an increased rate of development, aimed at earlier investigation of values disclosed by exploration drill holes has been attained with an overall reduction in unit costs.This paper describes the techniques used in rates of advance up to and exceeding 1,000 ft per 28-day period.

Jan 1, 1966

By Paul S. Goodman

This report examines absenteeism and accidents. The first section provides some background information on absenteeism. The second section examines trends in absenteeism in underground coal mines over time. The third section examines causes of absenteeism. Models were examined. The first model looks at self-report reasons for absenteeism. The second examines demographic correlates of absenteeism. The third model includes demographic and attitudinal predictors of absenteeism. The next section of the report examines the effect of absenteeism on accidents. The last section contains strategies for reducing absenteeism.

Jan 1, 1985

By P. A. Plunkert, D. E. Morse, L. McCartan, S. F. Sibley

The average annual growth rate of real gross domes-tic product (GDP) from the third quarter of 2001through the second quarter of 2003 in the United States was about 2.6 percent. GDP growth rates in the third and fourth quarters of 2003 were about 8 percent and 4 percent, respectively. Many other indicators reflected a rebounding U.S. economy — rising consumer confidence, higher retail sales, greater industrial production and more housing starts. Inflation also reached a 38-year low in 2003. The upward trends in many sectors of the U.S. economy in 2003, however, were shared by few of the mineral materials industries. Annual output declined inmost non fuel mining and mineral processing industries, although there was an upward turn toward yearend as prices began to increase (Table 1).

Jan 1, 2004

By C. V. Umipig, G. G. Hutalle, E. E. Israel

TVI Resource Development (Phils) Inc. Canatuan mine is a polymetallic ore deposit located in the Province of Zamboanga del Norte on the island of Mindanao in the Philippines. The deposit consisted of an oxidized capping of gossan overlying a Besshi type volcanogenic massive sulphide lens which is near surface and flat lying. Construction and development of a sulphide processing plant began in early 2007 and commissioned in November 2008. During the initial stages of sulphide operation, high copper (Cu)-low zinc (Zn) ore was fed to the plant. Marketable copper concentrate at 91-95% recovery was produced utilizing a high-pH bulk sulphide rougher flotation and 2 cleaning stages. Because of increased levels of Zn of the ore body, a Cu/Zn separation circuit was initiated in early 2010 following an intensive laboratory test work program. This Cu/Zn separation circuit was necessitated because of the copper ion pre-activation of the sphalerite that lead to the zinc being readily recovered to the copper rougher concentrate. In-situ activation of zinc (in the pit and stockpiles) was caused by the leaching of secondary copper minerals in the ore (particularly from the dominant copper species, chalcocite and covellite). This problem required the development of metallurgically complex and intensive reagent regime to effectively depress the activated sphalerite. As well, the immediate reactivation of zinc after it has been depressed, at the onset of Cu/Zn separation flotation, added additional metallurgical complexity to the process. Subsequent to the Cu/Zn separation circuit, an unconventional, yet proven effective, simultaneous cyanide detoxification-zinc flotation circuit was set-up to recover the zinc. Laboratory test work results realized Cu-Zn recovery differential from a Cu/Zn separation circuit of over 40-45%. This performance has been achieved in the plant, at 72% Cu overall recovery. With the gradual improvements on-going with zinc circuit capacity and effective zinc separation being achieved, zinc recovery has currently reached 40%.

Jan 1, 2012

By David R. Peterson

This user&apos;s manual covers a set of 5 computer codes which were generated during development of a simulation of deep ocean mining operational economics. Table 1.1 provides a summary of these codes, and a more thorough description of each follows, In addition to the descriptions in this user&apos;s manual, internal documentation is provided throughout each code, except for the very simple ones, for ease of understanding or possible modification. The two major codes are MINER, which performs the deep ocean mining system operational simulation, and MSWEEP, which calculates the sweep and feed efficiencies for a set of collector paths generated by MINER. The standard operating procedure is to input the system and operating parameters to MINER, which computes a set of collector paths automatically and stores the information in the fife PATH.DAT. MSWEEP subsequently retrieves the collector path data in PATH.DAT, and uses it to calculate sweep and feed efficiency. Separating MINER and MSWEEP allows parmetric execution of MSWEEP without recomputing the collector paths with MINER. PIPEST, RESP, and OBSTCL are special-purpose codes described in more detail in the following documentation.

Jan 1, 1979