Search Documents

By R. T. Sorensen

Research and testing in a small scale equivalent of a commercial flota-tion plant was completed on four low-grade, iron-bearing materials from the western Mesabi range. Closed circuit-flotation of calcium-activated silica with fatty acid collector developed data for comparison with the batch process and highlighted problems not evident from previous bench testing. The four ore samples contained from 27 to 39 percent Fe and were equally represented by nonmagnetic taconite and semitaconite type materials. Iron concentrates containing 6.0 percent, or less, SiO2 were made 5, all four samples. Of the two material types, the semitaconite was the ore amenable to treatment, yielding iron recoveries of about 90 percent as cc pared with 70 to 80 percent for the other. Pilot plant tests showed that concentrate grade made in batch tests could be duplicated in the closed circuit and demonstrated that the amount of recoverable middling iron varied considerably between ore samples. The continuous tests also showed that water temperature strongly influenced results in the treatment of one ore but apparently was of indifferent consequence in another. Progress in thickening and filtration of flotation concentrates was made through introduction of tapioca flour to serve the dual role of iron mineral depressant and flocculant.

Jan 1, 1966

This paper describes the economic study of longwall versus bord and pillar mining using all continuous miners for a colliery located at the South Coast district of New South Wales, Australia. In this district longwall mining appears to be a better economic proposition than bord and pillar. The internal rate of return on investment is found to remain approximately constant for each method irrespective of life. The economic importance of percentage extraction of coal is shown to be small for high values of minimum rates of return, becoming more significant as the minimum rate of return decreases.

Jan 1, 1980

By J. W. Paul, J. N. Geyer

"GENERAL STATEMENTThe purpose of this report, which is the first of a series of three covering mines in the Fairmont district of West Virginia, is to give the result of a' study conducted in seal mines to ascertain the nature of the safeguards employed to prevent injury to the workmen from falls of roof and coal. In presenting the subject matter, consideration must necessarily be given to factors, features, and conditions such as method of mining, timber regulations and practices, supervision and natural conditions; and, for comparative purposes, a certain amount of statistical matter bearing upon the relation of fatalities and injuries to their causes, tonnage produced, men employed, days worked, and time lost.Those features and practices found to promote safe protection are summarized and suggestions made for such additional safeguards and practices as appear to give greater protection against injury from falls of roof or coal.ACKNOWLEDGMENTSThis study of falls of roof and coal in mines in Harrison County has been conducted by the U. S. Bureau of Mines in cooperation with R. M. Lambie, chief of the Mining Department of the State of West Virginia who assigned L. W. Brown, a district mine inspector, to assist in the field work and in the preparation of individual reports on each mine visited in this study. The writers acknowledge the helpful suggestions and cooperation given by these officials, the latter of whom assisted in the field work and prop red most of these sketches for the individual reports which wore submitted to the operator by the chief of the department. Thin report is a summary of the contents of the individual reports heretofore furnished the individual operator."

Aug 1, 1931

By Josef K. Alter

Crosshole Sonic Logging (CSL) of drilled shafts requires 1.5-in (38-mm) or 2-in (51-mm) I.D. sonic access tubes to be installed inside the steel reinforcement cage. The sonic access tubes do not contribute to the structural capacity of the drilled shaft. The proposed use of Ischebeck TITAN T73/56 CSL/Hollow Threaded Rebar for Cross Hole Sonic Logging Access Tubes Combined with Longitudinal Concrete Reinforcing in Drilled Shafts (patent pending) is discussed as an alternative method of construction and CSL probe access. The T73/56 hollow threaded rebar/sonic access tube performs as a high strength rebar while at the same time creating a 2.2-in (56-mm) I.D. sonic access tube. The deformed high strength hollow bar provides better adhesion to concrete thus reducing the problem of debonding associated with smooth PVC and steel pipe. A cost comparison using conventional rebar with added sonic access tubes is discussed. The use of T73/56 CSL/Hollow Threaded Rebar as a value engineering alternative can reduce both material and labor costs for drilled shaft construction and can provide an advantage where anchor bolt cages and longitudinal reinforcing create congestion.

Jan 1, 2011

By J. Cygankiewicz

Efficient prevention of mine fires is impossible without predicting the self heating processes in the given geological and mining conditions. The respective forecasting method is presented in this paper based on the following assumptions: - factor deciding on fire hazard in the underground workings is the process of heating of coal from the primary rock temperature to the critical temperature when the heating rate growth rapidly - another important factor is the fire incubation time defined as time needed to achieve the critical temperature. This time is determined by balance of heat and mass in the heated coal - contact of crushed coal with oxygen in air cause some exothermic processes as : physical and chemical sorption of oxygen , oxidation reaction and evaporation of humidity Heated coal transfers its thermal energy to the environment by conductivity to the rocks and by convection to the flowing gases. The heating is possible if thermal energy generated from coal is greater then the share transferred to the environment. The paper presents the laboratory method of measurement of heat generation in adiabatic conditions. Also the mathematical model with examples of computation enabling to forecast the self heating process of crushed coal is presented.

Jan 1, 2003

By L. du Preez, J. D. Steenkamp

This paper introduces the concept of clean steel production from a pyrometallurgist’s perspective to the broader metallurgical community. A simplistic overview of the steelmaking process from iron ore to car body manufacturing is followed by an introduction to the South African steel industry and the technologies that it utilizes. The process is illustrated by an overview of the flow sheet and technologies for the production of clean steel at Saldanha Steel, South Africa.

Jan 1, 2015

By Thomas M. Gurtowski

The New Pacific Northwest Baseball Park, now known as Safeco Field, is located directly south of the Kingdome in Seattle, Washington, and will be the new home of the Seattle Mariners baseball team. The location of the ball field is shown on Figure 1, Vicinity Map. The seating capacity is 45,600, and outfield distances are 331 feet in left, 405 feet in center, and 326 feet in right field. The overall dimensions of the stadium are 680 by 800 feet. It is bordered on the east by the Burlington Northern Santa Fe Railroad main line. A unique aspect of this ballpark is the retractable roof with a north-south span length of 660 feet. The roof consists of three separate sections that roll on elevated rails running east-west on the north and south sides of the stadium. The soil conditions consisted of near-surface fill underlain with alluvial and Estuarine deposits to depths of 60 to 80 feet. The bearing soils consisted of very dense, glacially overridden deposits. Groundwater is 4 to 7 feet below the ground surface, and the alluvial deposits are subject to liquefaction during a strong motion earthquake.

Jan 1, 1998

By R. A. Friedel

THE UTILIZATION by the Bureau of Mines of infrared and ultraviolet-visible spectrometry in connection with coal research has led to some basic improvements in methods, including a calibration method, a quantitative assessment of infrared spectral energy sources, and the development and perfection of infrared filters and cells. The adoption of a micropipet method to flush organic samples into absorption cells permits the investigation of vapors from organic liquids and the identification of volatile organic compounds. The spectral method has been used to investigate the infrared spectra of metal chelates, the charge-transfer complexing properties of aniline and nitrobenzene, an infrared method for determining the presence of methane in coal-mine air that has been adopted for use in enforcing the regulations of the National Coal Mine Safety Act, and atmospheric pollution including smog and odor-causing oxidation and decomposition of organic materials. Correlation of spectra and structure of organic compounds, particularly aromatics, was studied.

Jan 1, 1966

By G. Bellefleur, K. Stevens, E. Adam, D. Synder, G. Perron, C. Müller

The Downhole Seismic Imaging consortium was initiated by the Geological Survey of Canada and three Canadian mining companies to assess the usefulness of borehole seismic techniques for the exploration of massive sulphide deposits within areas of steeply dipping stratigraphy. Field tests were conducted over two sub-economic massive sulphide deposits located in Norman West, Ontario, and Halfmile Lake, New Brunswick, using various shot configurations and a three-component borehole receiver array. The Norman West deposit, or structures associated with the deposit, produce detectable seismic reflections as far away as 1500 m. However, these reflections are difficult to distinguish from fault reflections and lithological contacts near the base of the Sudbury Igneous Complex. At Halfmile Lake, the rock properties are favourable for direct orebody detection. The Halfmile Lake deposit has a clear but relatively complex seismic signature on the downhole data, showing not only P-wave reflections, but also strong reflected S-waves and modeconverted waves. Such prominent S-waves and converted waves have not been recognized previously in borehole or surface seismic data acquired over massive sulphide deposits. These waves add complexity to the interpretation but provide additional imaging capabilities. Reflected S-waves and converted waves should be considered when designing seismic surveys for mineral exploration.

Jan 1, 2004

By Virginia T. McLemore

The Gallinas Mountains are in northern Lincoln County and southern Torrance County, New Mexico, USA where a series of alkaline igneous bodies, including porphyritic latite, trachyte/syenite, andesite, and rhyolite laccoliths, flows, dikes, and plugs, have intruded Permian sedimentary rocks belonging to the Permian Abo, Yeso, and Glorieta Formations. A small amount of bastnaesite, a REE mineral, was recovered during processing for fluorite from the Gallinas Mountains. Four types of deposits are found in the Gallinas Mountains: epithermal REE-F veins, Cu-REE-F veins, REE-F breccia pipes and iron skarn deposits; all are associated with Tertiary alkaline to alkalic-calcic igneous rocks. Alteration includes brecciation, silicification, chloritization, and fenitization. District zonation is defined by Cu-REE-F (±Pb, Zn, Ag) veins that form center of the district, surrounded by REE-F veins. Carbonatites are inferred at depth by the presence of fenitization, carbonatization of the breccias, presence of REE and similarity of the intrusive rocks and mineralization to areas with known carbonatites.

May 1, 2011

By V. McLemore, A. Fakhimi, K. Donahue, D. Sweeney, V. Viterbo

In order to evaluate the relationships between weathering and durability and strength of rock samples from the Goathill North rock pile at the Molycorp Questa mine, NM, we conducted slake durability and point load tests. Slake durability index (ID2) values ranged from 84 to 98%. Point load strength index (Is50) averaged for all rock units ranged from 1.1 to 5.7 MPa. Results show a slight positive trend between ID2 and paste pH. Two populations of data are distinguishable when ID2 is plotted versus the percentages of chlorite, illite and internal friction angle. In general, Is50 values increase toward the interior of the rock pile. Preliminary conclusions indicate that the durability and strength of the rock pile material generally increase toward the interior of the rock pile. Pre-rock pile alteration and post-rock pile weathering history have affected the durability of the GHN rock pile samples.

Jan 1, 2007

Radioisotope x-ray and neutron techniques of analysis can be used for the determination of a wide range of elements in minerals. The most important applications of these techniques to the mineral industry are for onstream analysis of slurries and solids, and for geological assay.The radioisotope x-ray techniques are the more developed ones and two installations for on-stream analysis are in routine use in mineral processing plants in Australia. Neutron techniques are being developed, and should prove valuable for geological assay of large numbers of mineral samples, for borehole logging, and for specific on-stream analysis when the cost of the equipment is warranted.

Jan 1, 1970

Authors have been conducting research on autonomous loading operation by wheel loader. Autonomous loading cycles has been demonstrated with real size experimental model. In V shape loading operation, travelling between scooping point and dumping point is dominant factor for cycle time of the operation. The positions of scooping point and dumping point changes with advancing the operation. In the developed system, path planning is performed at the beginning of every cycle. The path is formed by combination of curve and straight path elements. During travelling on the planned path, path following control is applied on the loader to keep position error in narrow range. Positioning of the loader is based on dead reckoning with correction by global positioning system (GPS) data. In a process of path following control, control value for steering angle is determined based on position error in lateral direction. Proposed method of path planning and position control is installed and tested in the real size experimental model. The detail and results will be described in the paper.

Dec 6, 2010

By V. Rajaram

Rock reinforcement systems are used in open pit and underground mines to stabilize the rock mass in-situ and provide safe working conditions. Significant progress has been made to date in the design and implementation of rock reinforcement systems to accommodate bad rock conditions and larger excavations. However, the rationale for the design of rock reinforcement systems remains essentially the same and can be categorized into three groups, namely 1. to create a beam of competent rock in stratified formations, 2. to resist sliding motion in jointed rock, 3. to passively support the superincumbent loads in highly stressed ground. Case histories of the rock reinforcement sys¬tems that illustrate these design approaches will be presented in this paper.

Jan 1, 1983

By McMillan W. D.

Vermiculite is the name of a group of micaceous minerals characterized by their property of exfoliating when heated and thereby increasing many times their original volume. The resulting product has excellent heat-and sound-insulating properties, is used as a lightweight aggregate, and has numerous other industrial applications. Deposits of vermiculite occur in areas of pre-Cambrian rocks of the Llano uplift of central Texas, particularly in Burnet and Llano Counties. Because of the growing economic importance of vermiculite products, the Bureau of Mines undertook a detailed investigation of several deposits in Llano County. This investigation was completed in February 1947. The work comprised topographic surveys of five deposits, drilling with a 4-1/4 inch Parmanco power auger drill, and laboratory evaluation of samples. 342 drill holes, aggregating 4,905.5 feet, were completed, and 377 samples were taken. Laboratory evaluation of the vermiculite comprised expansion tests on both crude and beneficiated samples. The products obtained were compared with commercial-grade vermiculite from Montana.

Jan 1, 1949

By R. W. Fedors, S. T. Green, R. A. Hart, D. B. Walter

Computational fluid dynamic (CFD) modeling of a potential nuclear waste repository drift may be an important tool to estimate moisture redistribution caused by natural convection within the drift. To refine and support CFD techniques, a small laboratory cold-trap experiment was developed. Results from numerical modeling of the laboratory experiment show the sensitivity of the bulk air flow rate and average air temperature within the drift to several key parameters, including various boundary condition assumptions and surrounding porous media properties.

Jan 1, 2004

This is an abstract from Environmental Service and Technology (Vol 32 No 20 1998) which will be o finterest to South African Mining and Metallurgical Scientists, involved in chromium mining and Metallurgical processing. Maybe the scourge of our dams and reservoirs?the water hyacinth can be put to good use! The novel technology of phytoremediation embraces plant accumulation processes for the cleanup of toxic heavy metals and organic chemicals. Several plant species have been identified that are excellent hyperaccumulators of a number of heavy metals, e.g., Brassica juncea (Indian mustard) and Thlaspe caerulescens (Alpine pennycress). Other speciesincluding Myriophyllum brasiliense(Parrot?s feather), Salixsp. (willow), and Popullussp. (poplar) have also demonstrated phytoremediating abilities.

Jan 1, 1999

By William Gleason

"It is safe to say that the coal industry, in the United States and globally, is currently suffering through one of the hardest times in its history.A perfect storm of competition, changing energy demands, politics and public perceptions have collided, inflicting significant harm to the industry that many say is irreparable. This, in turn, has led to massive job losses in some regions, heavy cuts in production and even bankruptcy filings from two of the largest coal mining companies in the nation.Cheaper natural gas can certainly take a large share of the blame for the struggle of coal, as utility companies switch from coal to natural gas for power generation. According to the U.S. Energy Information Administration (EIA) the amount of coal used for electricity generation in the United States is at a 45-year low.November 2015 marked the fifth consecutive month that natural gas was the leading source of power generation in the United States. EIA said generators produced 101,866 thousand megawatt hours (MWh) of electricity with gas in November versus just 87,789 thousand MWh with coal, the lowest monthly level since May 1980 when monthly coal use was 84,884 thousand MWh.According to Robert Godby, director of the Center for Energy Economics and Public Policy at the University of Wyoming, there are a number of factors playing a role in the decline of coal, but he points to the advances in fracking as the tipping point.“A lot of people will argue that regulation is the cause of the decline, and it has played a part, for sure, but the story of the recent past is more about what competition has done to the energy market,” Godby told Mining Engineering. “The war on coal was originally declared by natural gas in 2008.”The price of natural gas, which was at $13 per million Btu before the gas fracking boom, has fallen to as low as $1.68 in December 2015. Likewise, Godby said the cost of wind generation is now lower than the cost of generation from coal and the cost of solar generation is coming down as well. In addition to that, the demand for energy has changed in the past five years with more efficiencies in everything from building design to lightbulbs."

Jan 1, 2015

By Geoffrey Hughes

The Narragansett Bay Commission (NBC) is a regional sewer authority that serves ten communities in the Providence, Rhode Island metropolitan area. From 1992 to 1999, the NBC developed a comprehensive facilities plan to abate Combined Sewer Overflow (CSO) pollution in the Upper Narragansett Bay. The plan underwent many major evolutions during this period, most notably the addition of a stakeholder?s process by which NBC demonstrated a site-specific plan to control the pollutants and meet water quality standards. The favored solution consisted of deep tunnel storage with treatment at existing wastewater facilities that had been recently upgraded. In 1999, a final plan was accepted which included two tunnels, five CSO interceptors, twelve sewer separation projects, a wetland facility, and a wastewater treatment facility upgrade. The program is to be constructed over 20 years in three sequential phases (Figure 1). Phase I of the program includes a 4,963 m (16,284 ft) long, 7.9 m (26 ft) diameter, 70.1 m (230 ft) deep storage tunnel; seven drop shafts with connecting adits; ancillary facilities; and a pump station. Construction of Phase I began in 2001 and is expected to be operational by October 2008. This paper focuses on design and construction of the Fields Point Tunnel Pump Station (FPTPS)located at the south end of the main spine tunnel. A189 Ml/day (50 MGD) pump station is required to lift CSO flows from the tunnel to the Fields Point Wastewater Treatment Facility (FPWWTF). The pumps are to be housed in a 35.6 m × 18.6 m ×20.7 m (117 ft × 61 ft × 68 ft), 91.4 m (300 ft) deep cavern excavated in a complex meta-sedimentary rock of the Rhode Island Formation, and connected to the surface by 9.7 m (32 ft) and 3.4 m (11 ft) diameter shafts. Factors which influenced selection of the size, configuration and location of facilities included the preferred arrangement of pumps, critical aspects of site geology, and estimated cost. Technical and value engineering reviews also affected the final design. Following Notice to Proceed (NTP), concerns were raised by the contractor regarding constructability and design. Additional geotechnical investigation and independent engineering review were employed to validate the design assumptions. The cavern was successfully excavated and sup-ported in rock, completed on schedule and within budget in 2005. In 1992 the NBC retained Louis Berger Group (LBG) as Program Manager (PM) for the CSO Abatement Program. LBG thereafter formed a design team including: Jacobs Engineering Group(JEG) as the designer for underground structures and near surface collection facilities; Black and Veatch(B&V) to design the pumping system and associated facilities; Haley and Aldrich (H&A) to oversee the geotechnical program; and Malcolm Pirnie to design the system-wide instrumentation and control system. Construction management, resident engineering, and inspection services were provided by the joint venture Gilbane/Jacobs Associates (G/J).

Jan 1, 2008

By Wenbing Xie

At Renlou Coal Mine, Huaibei Mine Area, the track entry deformed significantly after longwall mining in an overlying multiple seams. The supporting characteristics of primary roof bolts and shotcrete with wire mesh are closely related to the movement of the mine?s surrounding strata. A case study of a track entry deformation was monitored during the longwall mining of a selected overlying panel. The measured data showed the unique entry deformation pattern during the longwall mining in the overlying seam. Underground extensometer measurement showed that entry stability was mainly affected by the periodic roof weighting of longwall mining in the overlying seam. The displacement of the deeper strata occurred a head of the immediate vicinity of the entry. Thereafter, deformation of the roof and floor strata was in the form of shearing of the shallower strata. Due to the use of heavy-duty roof bolting with wire-mesh, the roof-tofloor and rib-to-rib convergences were small, but the floor heave was large, greater than 80% of the roof-to-floor convergence. The measured displacement from extensometers varied with the position of the monitored cross-sections and depth into the roof. There were several deformation patterns, such as shearing movement, compression, and expansion, and the variations between compression and expansion. Strata compression at the entry surface was always accompanied with shearing movement at the deeper strata. During the longwall mining, the whole surrounding strata of the entry moved toward the opening. Underground practical experience indicated that prior to mining, the entry was supported very well in excellent conditions. After mining, however, it deformed greatly. The current entry support technology was not effectively control the severe deformation incurred in entries driven in soft strata due to the following reasons: (1) little is known about the entry deformation behavior of the strata surrounding the opening and (2) the degree of interactions between entry deformation and roof bolting with wire mesh is not well understood. Consequently, effective supporting systems cannot be properly selected to control its deformation and maintain a stable supported surrounding structure.

Jan 1, 2012