Search Documents

By S Vianna, K Caldwell, R Silva, T Olson, D Bell

Studies to enhance the FLSmidth forced air machine through changes in the design, showed important improvements through changes in the number of Rotor blades, stator designs, rotor air distribution and other designs features. The main outcomes from this study highlighted that increasing the number of rotor blades increased the selectivity while decreasing power requirements while stators with slots have better results in terms of recovery, flotation efficiency and selectivity than without slots.Also the rotor air distribution makes a difference in the design when comparing different distribution criteria whilst keeping all features of shape and number of blades etc constant. At the most efficient rotor air distribution design, copper recovery reached one of the highest values while keeping good selectivity. The possible explanation for that is the increase in the pump capacity indicated by the increase in the specific power.It was seen as significant that reduction in specific power for some designs tested compared with the then current standard design had an average of 30% less power consumption.As a result, FLSmidth was able to identify new designs that decreased power and improved recovery, as well as, identifying some designs that specifically improved fine and/or coarse particle recovery.CITATION:Silva, R, Caldwell, K, Bell, D, Olson, T and Vianna, S, 2013. FLSmidth flotation developments - Dorr Oliver machines, in Proceedings MetPlant 2013 , pp 413-430 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Bill Linville

During fiscal year 1969, the Bureau of Mines was engaged in 66 projects to improve methods for producing and utilizing petroleum. Programs directed toward the continued conservation of this natural resource, including crude oil, natural gas, and oil shale, were carried out through research performed at four laboratories supervised and supported by administrative personnel of this Bureau of the Department of the Interior. Over 100 technical papers and reports were published by the Bureau or others based on this research, and numerous other reports were prepared for U.S. Government agencies, State agencies, and organizations of the petroleum and natural gas industry engaged in cooperative research programs with the Bureau.

Jan 1, 1971

By Niels Kofoed

Upon completion of the 6,200 m (20,340 lineal ft; lft) North Tunnel drive for the Portland East Side Combined Sewer Overflow (CSO) Tunnel project in Portland, OR, the slurry tunnel boring machine (TBM) had to be returned from the Port Center shaft at Swan Island to the Opera shaft at the main mining site for the 2,700 m (8,860 lft) South Tunnel drive. At the Port Center shaft, the main 513-t (565-st) TBM and TBM tailshield were hoisted out of the shaft in two pieces using four 200-t (220-st) strand jacks mounted on a 635-t (700-st) hydraulic boom gantry system supported by Emmert International?s custom gantry tracks designed to span the shaft. After lifting the TBM components out of the shaft, the gantry system loaded the TBM components onto two Goldhofer platform trailers, which then transported the TBM and tailshield to a barge using a roll-on/roll-off method.

Jan 1, 2011

Education and training research is a major component of the Bureau of Mines human factors research program. The goal of human factors research is to enhance human performance for the purpose of improving both safety and the profitability of the minerals industries. This is achieved through the design of mining equipment, work tasks, management procedures, and development of human resources. This proceedings volume presents several new developments that are helping to improve the quality and efficiency of health, safety, and occupational skills training in the mining community. Several papers address the issue of how to teach and assess miner abilities to deal with underground mine emergencies. Other papers examine practical procedures for defining and cost justifying the integration of structured training and other performance improvement strategies to enhance the proficiency of the work system.

Jan 1, 1988

By P. -É. Boileau, M. Smets, T. Eger, J. Boutin

Long-haul dump (LHD) vehicles used in underground mining are known to expose workers to important levels of whole-body vibration1. These vehicles are generally designed without suspension and may be categorized as small or large LHDs depending on whether their respective load capacities are lower or larger than 3.5 cubic yards. While the majority of older vehicles are equipped with a rigid or unsuspended seat, more recent LHDs often incorporate a suspension seat. The objective of this study was to define the vibration spectral characteristics of most commonly encountered large and small LHD vehicles operating in mining operations. This was done in an effort to categorize the vehicles in terms of vibration spectral classes to be reproduced on a laboratory whole-body vibration simulator to assess the vibration attenuation performance of a typical LHD suspension seat. Methods Vertical vibration measured at the seat attachment point of 8 small and 8 large LHD vehicles operating underground in typical mining operations under loaded and unloaded conditions was considered as the basis for defining the spectral classes. By regrouping the data collected for each LHD vehicle size and load condition, the overall distribution of acceleration power spectral density (PSD) of measured floor vibration was determined over the 0.5 to 20 Hz frequency range. Mean and envelopes of maximum and minimum values of PSD spectra were computed to define the spectral classes, along with the corresponding values of frequency weighted rms acceleration determined in accordance to the ISO 2631-1 standard2. These spectra were further used to calculate the displacements needed to drive a whole-body vibration simulator consisting of a platform supported by two servo-hydraulic actuators having a total stroke of ±100 mm. For validation purposes, the vibration acceleration spectra measured on the simulator were compared with the target spectra representing the spectral classes. Finally, the vibration transmissibility characteristics of a typical suspension seat were determined under sine sweep excitation using both a rigid mass load and a human subject having a mass of 62 kg and 85 kg, respectively. The SEAT value, representing the ratio of seat to base frequency-weighted rms acceleration, was further measured under each of the defined LHD vibration spectral classes by loading the seat with an 85 kg subject. Tests were repeated three times and the mean SEAT values were determined to assess the seat’s ability to reduce exposure to whole-body vibration in LHD vehicles. Results Three spectral classes applicable to both loaded and unloaded conditions were defined as shown in Figure 1: one for large and two for small LHDs. The influence of load on frequency-weighted rms acceleration was found to be negligible for large and Class I small LHDs, while a shift of the peak acceleration PSD to lower frequencies was noted for the loaded vehicles. The influence of load was found to be more important for Class II small LHDs. Table 1 provides a

Jan 6, 2006

By J. du Plooy

Mintek has implemented a training scheme that provides students with the experiential training requirement for the National Diplomas in Chemical Engineering and Extraction Metallurgy. This note describes the main features of the scheme and the course content, and our view of future developments in this area.

Jan 1, 1998

By C. D. Hebert, M. R. King

The 56,000' (17 km) long San Vicente Aqueduct Pipeline tunnel is being constructed using precast concrete rings to act as preliminary ground support through two sections of the bored tunnel with lengths of 9,450' (2.9 km) and 33,700' (10.27 km).The six segment bolted trapezoidal ring was manufactured using a combination of steel fiber reinforced concrete and self compacting concrete in vertical moulds. This paper briefly describes the design and function of the segments, and reviews the development stages of the concrete mix, and the advantages and disadvantages of the adopted manufacturing method.

Jan 1, 2007

The National Mining Hall of Fame will induct five mining greats on Saturday, Sept. 17, 2005 at the Museum Convention Center in Leadville, CO. The 18thAnnual National Mining Museum and Hall of Fame Induction Banquet will begin with an open house and reception at 5:30 p.m., followed by the dinner and program at 7 p.m. The five inductees are Nathaniel Peter Hill, John Munro Longyear, John McDonald, Julius Eckhardt Raht and John Dennis Ryan. Nathaniel Peter Hill (1832-1900) built the first successful smelting operation in the Rocky Mountains in1867 at Black Hawk, CO. From 1879 to 1885, he was a U.S. senator. He also taught courses at the Colorado School of Mines.

Jan 1, 2005

By P. A. Plunkert, D. E. Morse, Pui-Kwan Tse, W. D. Menzie, Lucy McCartan, J. F. Papp

China’s burgeoning economy is responsible for a major share of recent world mineral consumption increases. In addition to factors traditionally recognized in market economies1 and factors unique to specific commodities, Chinese consumption now plays a major and increasingly important role in energy and mineral markets for many commodities, such as aluminum, copper, iron and steel, and oil. China has the world’s second largest economy after the United States. And its long-term importance to the minerals markets is even greater than indicated by its gross domestic product (GDP), which is currently less than two-thirds of that of the United States (Table 1). This is because China’s rising standard of living is accompanied by rapid industrialization and urbanization. Its consumption of mineral materials for infrastructure development for its very large population is significantly greater per capita than that of such developed economies as the United States, the European Union and Japan. In other words, China’s per capita production is rising at a rapid rate and will probably continue to do so for many years.

Jan 1, 2006

By D. Hatfield

"Flotation plants typically aim to maximise recovery at or above a target grade. As the ore from the mine varies, operators increase or decrease the mass pull in different flotation banks by adjusting air and level set points in order to achieve target concentrate grade. A methodology has been developed to maximise overall recovery at target grade by determining the optimal mass pull for each bank. However, the approach of targeting equal grade for each ore type in the deposit leads to sub-optimal overall recovery. This is because some ore types sacrifice a large amount of recovery to reach target grade while others easily achieve target grade and can be processed at higher than target grade for little or no loss in recovery. Processing different ore types at different grades and blending the concentrates therefore gives a higher overall recovery.This paper presents a case study where an 80 year production forecast was made for a large Chilean copper concentrator in feasibility stage. A circuit model was created using SGS’s Integrated Geometallurgical Simulator (IGS) for the different ore types to be processed. The model was calibrated from standard rougher flotation tests (MFT), cleaner tests and from the results of plant surveys of similar operations. The pull rates for each bank in the circuit were determined to achieve an optimal graderecovery curve for each ore type. These curves were combined at different concentrate grades for each ore type to obtain the mathematically optimal overall recovery at target grade. The paper shows a methodology for obtaining an optimal combination of operating conditions for each ore type to maximise overall recovery at a set combined concentrate grade."

Jan 1, 2013

THE object of the present paper is to give a brief description of the metallurgical process followed by the Grand Junction Co, and the results obtained therefrom. All figures quoted are from the actual working of the plant over a period of six months from January to June, 1910. The short ton of 2000 lb. is used by the company. Its gold is valued at 84s. per oz. fine, silver at 2s. per oz. fine. The ore consists essentially of a gangue of quartz and calcite, with 8 to 10%sulphide-pyrite, sphalerite, galena, chalcopyrite, and traces of arsenic and antimony. The colmtry-rock is a highlyaltered dacite. Small stringers of highly-mineralized ore penetrate the footwall of some of the lodes, forming a valuable stockwerk up to 3 ft. in thickness. In stoping, this is mined with the well defined lode, thus bringing into the mill at times a considerable quantity of hard country-rock. The gold exists in an exceedingly fine state of division, consequently rendering it necessary to grind very fine to obtain a satisfactory extraction.

Jan 1, 1912

By H. F. Yancey, E. Zane

"INTRODUCTION The term ""friability"" as applied to coal may be defined as the physical property of coal which expresses its tendency to become reduced in size during handling as a result of such external forces as impact and attrition. Thus friability is a quantitative concept and property, and hence can only be defined in relative terms or in terms of measurement. Methods of measurement are difficult to formulate and apply because coal is anything but homogeneous in physical structure and chemical constitution. aMoreover, friability itself is a composite property obviously dependent upon a group of other specific characteristics such as cleavage, fracture, tenacity, hardness, and elasticity, which vary from coal to coal with change in rank and even between individual coals of the same rank. These characteristics affect the friability values of different coals to varying degrees, but this fact does not impair the usefulness of and the need for friability measurements.The amount of breakage or degradation in size that a coal suffers in mining, preparation, and subsequent handling depends upon its inherent friability and the severity of the handling treatment which it receives from the time it is taken from the bed until it reaches the consumer. The value of the coal to the producer and jobber depends in large measure upon these same factors--friability and severity of treatment—because the larger sizes still command a premium in the ordinary market. Although much has been accomplished by the coal-producing industry in minimizing the breakage of coal in mining and preparation, it is apparent that additional reductions in breakage must await further improvements in design of coal-handling equipment. Such improvements will result from more intensive investigations of the extent of breakage or degradation in size occasioned by specific mining and handling operations and the development and application of standardized methods of evaluating friability.The work described in this report was undertaken to assist in the development of standard methods for evaluating the friability of coal. Specifically, the work deals with a Comparison of the various methods previously proposed for estimating the friability of coal and coal products. This same objective is now being sought at a number of other institutions, both in the United States and Canada, by a committee of the American Society for Testing Materials. It is believed that by providing additional information concerning a property of coal pertinent to its increased usefulness, the work described will supplement and increase the useful of the data which long have been, and still are being, furnished by the bureau of Mines on the composition of coals of the United States."

Jun 1, 1933

By Christopher J. Bambridge, Lee Seng Hoor

The Stormwater Management and Road Tunnel (SMART) Tunnel is a world first in the use of tunnel space transmitting both road and water through the same spatial envelope. The unique aspect of the SMART project is that the highway decks are used periodically for the conveyance of water. This aspect of the project has posed its own technical challenges that have been overcome in the design stage of the work allowing the project to be taken forward to construction with confidence in the systems to be Installed in the tunnel.

Jan 1, 2005

By D. Ksinsik, R. Boisvert, D. Leblanc

Casting, cooling and crushing/sieving of ferroalloys has followed a well-established pattern in the whole ferroalloys industry for many years. Usually liquid metal or alloys are cast into flat open moulds of various shapes and forms, and after solidification the product is removed from such mould to further cool down to a temperature where subsequent handling steps are feasible. Common to all mechanical product fractioning is the generation of dust and fine size material with lower product value. For almost 10 years, Bécancour Silicon has investigated alternative roads to improve technology and/or reduce or solve problems related to those disadvantages. Since 1995 Bécancour Silicon operates a special silicon granulation plant targeted to product for the chemical treatment/conversion of silicon for silicones production. Prior to the development of the granulation process, various systems had been evaluated, among others the vibrating casting bed, now in operation elsewhere but judged inappropriate because of the tapping volumes to be handled at Bécancour Silicon and other disadvantages. After evaluation of all aspects of heat transfer, radiation, and conductivity in relation to transfer media and within the product, a novel system was designed and built.

Jan 1, 2004

The small scale alluvial gold mining industry in Papua New Guinea (PNG) is c.irrently the only form of small scale mining carried out in this country. It already contributes significantly to the economy with current production estimated at 2 000-2 500kg per year. Until recently, small scale alluvial gold mining has been confined to simple panning and sluicing of high grade alluvial and colluvial deposits. Traditionally the small scale miner in PNG has only worked gravels with gold grades in excess of 500mg/m3. Grades of this order are required to justify the hard physical labour involved ~n hand operated small scale mining methods. .he introduction of higher throughput technologies such as trommels fed by hydraulic excavators has the effect of altering what constitutes an economically viable deposit. Mechanised techniques allow for the consideration of grades of almost half that level. The potential and opportunities for utilising this type of small scale mechanised mining in PNG are enormous with large areas of ground with gold grades running in excess of 250mg/m3 and often up to 2000mg/m3 throughout the country. An assessment of the current operating economics of this technology in the PNG context is the principal objective of this paper. Small to medium scale mechanised mining can potentially contribute significantly to the PNG economy particularly as it lies within the react-, of many PNG businessmen. Its potential is currently somewhat limited by a general lack of infrastructure and is also constrained by socio-political factors.

Jan 1, 1991

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,500 tons of ore per day with an average gold grade of 0.34 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. Based on the characteristics of the ore bodies, a long-hole stope and cut-and-fill mining methods are used at the deposits which are divided into several mining zones. Cemented rock fill (CRF) is used as the backfill in the open stope. CRF design includes the aggregate design, the ratio of cement and fly ash design, and strengths for the long-hole stope and cut-and-fill. In the aggregate design, the particle size distribution is one of the most influential aggregate characteristics in determining how it will perform as a basic backfill material. Gradation helps determine durability, porosity, cement and water requirements, strength, and shrinkage. To cut the backfill cost, fly ash usually is added into the binder to replace some part of cement. However, adding fly ash can affect the strength of the backfill. The reasonable percentage of fly ash is also important for making a good and low cost backfill. Based on the different mining method, the different backfill with different strength is designed. A systematic quality control procedure for aggregate and backfill is followed. After four yeas application, CRF system in Leeville achieved very good results.

Jan 1, 2011

THE most important part of the routine survey work on a mine is the keeping up-to-date of plans and sections showing progress of stoping and development work, and the direction of the latter for the purpose of making necessary connections. Except in specialcircumstances, e.g., major horizoittal development, the exactitude required in this work is not extreme, and a method of survey in keeping with the demands of the work itself is all tbat is required.For example, no one would consider measuring the walls of a stope to a fraction of an inch; such extreme accuracy would be wasted.The stope walls being irregular, a mean is usually taken, and for ordinary purposes a survey with a limiting error of six inches is quite satisfactory for the purpose of plotting either stoping or development.It is the author's aim in this paper to describe the method in use at the North Broken Hill Oompany's British mine. This method, while being sufficiently accurate for the purpose in view, possesses the very great advantages of speed and simplicity of operation,with a minimum of necessary equipment. This latter is a very important item where several surveys on different levels have to be carried out on the one day.Let it be understood, however, that the use of this method does not dispense with the theodolite, but simply serves as a convenient adjunct to obtain details and to extend the accurate theodolite survey up rises and down winzes, and through ladderways orwinzes into stopes, where the use of a theodolite, if not actually impossible, is often exceedingly inconvenient. This is particularly so on the British mine, where a large proportion of the ore is won from narrow and complex-dipping lodes, and where vertical ore...

Jan 1, 1928

By Robert M. Becker

Part 5, the last of this series, deals with the theoretical confirmation and application of results developed in parts 1 and 2. The bulk-sampling variances of Hassialis and Kassel and Guy are compared with those in part 2, both as to formulation and as applied to ores and coal. The results provide confirmation for much of the development in part 2. Examples are presented for determining the reliability of bulk samples with respect to various measurable characteristics. These characteristics include, for example, assays for elements or compounds and particle surface area. The bulk samples considered consist either of a given weight, a given volume, or a given number of particles. In addition to problems of sample reliability, some of these examples may also be applicable to quality control. Several possible applications of results developed in parts 1 and 2 are outlined. These include tests for random data, degree-of-mixing indices, and particle-fineness indices.

Jan 1, 1966

By B. Papillon

There has been a veritable increase in the adoption of electronic detonators in the last few years. Electronic detonators offer several distinctive features over electric and non-el (shock tube) detonators including better timing accuracy resulting in excellent fragmentation and vibration control, certainly key mining parameters. The field programmability also helps in reducing the on-site magazine storage of detonators with diverse fixed delays. A typical electronic detonator may consist of a logic core, a communication interface, storage capacitor(s) and the ignition element. Being electronic components, the electronic detonators may be susceptible to RF or electromagnetic interference (EMI). RF sources are virtually everywhere: cellular phones/towers, radio transmission, microwaves, walkie-talkies, high voltage (HV) transmission cables and wireless networks with their characteristic frequency emissions. Safety issues prevail; e.g., whether the RF interference can cause premature or inadvertent firing whether directly or indirectly. From a reliability perspective, the RF interference may also impact on bus communications, e.g., during the logging, verifying, charging and firing phases. The deleterious communications disturbance may result in a misfire (non-firing of one or more of the detonators) which is terribly inconvenient for the mine operators and even pose a safety hazard.

Jan 1, 2009

By Harmon E. Keyes

Many organizations, including the Bureau of Mines, have made intensive studies of the application of leaching methods to relatively small low-grade disseminated deposits of copper ores, containing both oxide and sulphide minerals. One of the principal difficulties has been to obtain a solvent that could be made at a low cost and would effectively dissolve the copper minerals. Another drawback has been the high initial cost of a plant and the refined type of mechanism ordinarily required by standard practice for carrying out the leaching cycle. The Bureau of Mines has attempted to develop a cheap and efficient solvent that would especially meet the requirements of smaller plants. (See Bibliography.) It has been known that dilute ferric sulphate-sulphuric acid solution is an excellent solvent for most copper minerals, such as chalcocite, bornite, and oxidized forms, but not for chalcopyrite and certain silicates. A method of producing this solution from sulphurous products and waste liquors was developed by the bureau and tried successfully on a test-plant scale at the Southwest Experiment Station in cooperation with the department of mining and metallurgy, University of Arizona, Tucson, Ariz. However, this work did not involve the actual leaching of ores with the solutions thus produced or the cyclic use of the iron solutions in the regenerator cell. Except for certain laboratory tests, in which known impurities were added, no data were available to show the effect on regeneration if accumulations of impurities were built up in the leaching circuit.

Jan 1, 1930