Search Documents

Python Underground Processing Plant Critical Design The use of continuous gravity recovery in combination with a controlled breakage fine crushing and screening system followed by flash flotation has been incorporated into the Python processing plant. This provides miners with a flexible, robust, low cost, low energy pre-concentration process for the recovery of gold and/or heavy minerals. The Python plant incorporates fine crushing utilizing either High Pressure Grinding Rolls or Vertical Shaft Impactors in combination with the InLine Pressure Jig and Flash Flotation to continuously liberate and recover the valuable minerals. The use of these technologies has enabled a narrow, transportable pre-concentration plant to be produced which can easily be installed and operated in underground drifts and tunnels.

Sep 13, 2010

By Timothy D. Stark

Jet grouting has increasingly become one of the ground improvement technologies used to address seepage concerns and to provide strength improvement of soils. The technique of jet grouting uses high pressure/velocity jet fluids to erode the existing soil and then to mix the cuttings with cement slurry to form soilcrete. Excess slurry or spoil is ejected to the surface. If the native soil is not completely mixed with slurry, the resulting columns will have soil inclusions which can reduce the strength of the column and/or increase the permeability of the column. A jet grout test program at Tuttle Creek Dam shows that the completed large diameter columns contain perhaps 40 to 50% or more of native soil that was not broken up and mixed during the jet grout process. The test program included excavation of full-scale columns to a depth of 35 ft (10.7 m) for visual inspection and testing. Additionally, six of the columns were cut or sectioned to investigate the interior of the columns. The observed inclusions include significant amounts of both fine grained (silts and clays) and coarse grained (fine sands and sands) soils. Evidence suggests at least two explanations: (1) fine grained soils can be difficult to erode and break up into small enough particles that can be ejected to the surface, especially if at low natural water content, and (2) when large diameter columns are being excavated, the excavated roof of the cylindrical cavity may be unstable and may collapse. With this roof instability large slabs of material can break off, fall into the slurry and escape the cutting and mixing action of the rotating jets. This paper describes the Tuttle Creek Dam test program, inclusions observed in the completed columns, and suggests potential causes of the inclusions.

Jan 1, 2009

By M. Vallée

"Geological and technical problems are often considered the most important ones affecting new mining projects. Typical problems and likely causes are reviewed based on current Quality Management and Continuous Improvement (QMCI) perspectives, giving particular attention to the work of W.E. Deming. As the “system approach” is an essential part of these policies, its characteristics are described with particular attention given to cultural- behavioural, organizational and systembased constraints described by J. Gharajedaghi. Given that poor communication and interaction among geologists, mineral processors and mining engineers/operators can seriously affect the adequacy of tests, project planning and execution, and mine profitability, these interrelated processes within the mining systems are analyzed and modelled. The impacts on models and simulations of ignoring typical data, information and knowledge uncertainties are addressed. Adapting W.E. Deming’s Fourteen Points, System of Profound Knowledge and insistence on leadership, and the analysis of mining system constraints, will allow the effective QMCI approach required to reduce geological and technical risks. Whenever we achieve this goal, we will be in a better position to overcome environment-, market-, finance- and community-related problems, achieve higher company and industry profitability as well as more sustained development. RÉSUMÉLes problèmes géologiques et techniques sont souvent considérés les plus importants parmi ceux qui affectent les nouveaux projets miniers. Des problèmes typiques et leur causes sont étudiés dans la perspective de gestion de la qualité et d’amélioration continue (GQAC), en relation avec les travaux de W.E. Deming. Comme l’approche système est au centre de ces méthodes, ses caractéristiques sont décrites en donnant une attention particulière aux contraintes de types culturel-comportemental, organisationnel, et systémique décrites par J. Gharajedaghi. Compte-tenu que les lacunes dans les communications et les interactions entre géologues, minéralurgistes, et ingénieurs/opérateurs miniers peuvent affecter sérieusement la validité des essais, de la planification et de l’exécution des projets ainsi que la rentabilité des exploitations, ces processus connexes font l’objet d’analyse et de modélisation. Les impacts sur les modèles et les simulations de l’incertitude des données, informations et connaissances sont soulignés. En adaptant au système minier les Quatorze Obligations et le Système de connaissance approfondie de W.E. Deming ainsi que l’analyse des trois types de contraintes, nous pourrons développer une approche GQAC permettant de réduire les risques géologiques et techniques des projets miniers et des exploitations. Ceci nous pemettra de mieux faire face aux problèmes reliés à l’environnement, aux marchés, au financement et aux conditions sociales, d’améliorer la rentabilité des exploitations minières et de l’industrie, tout en contribuant de façon accrue au développement durable."

Jan 1, 2003

The Sage Mill Project w approved by Santa Fe Pacific Gold Corporation's Board of Directors in October 1994. The Sage Mill Project included a pressure oxidation plant designed and constructed to process refractory carbonaceous ore using fine grinding/autoclaving technology developed specifically to treat Twin Creeks ore. The project was constructed in two phases. The first phase was put into operation on May 5, 1997, just hours before the transfer of ownership to Newmont Gold Company occurred. The second phase started in October 1997. This paper reviews schedule, costs, scope changes, and methodology used on the project that spanned almost five years from project definition through commercial operation.

Jan 1, 1999

A wide range of materials are used in hydraulic backfilling operations and the pipeline flow behaviour of these mixtures varies considerably. It is shown that despite the large differences in constituent materials and flow behaviour, a common approach can be applied to analysing the flow of all hydraulic backfills. This is extended to include a rational design approach for backfill distribution systems. The use and limitations of pipe loop tests as a design aid is discussed. Backfill quality control is identified as a key area where improvement needs to be made to enhance the reliability of backfill system operation.

Jan 1, 2001

By King R. L

Low-enthalpy geothermal groundwater resources occur at relatively shallow depths in the Upper Cretaceous/1'ertiary sedimentary sequence in the on-shore Gippsland Basin. The main stratigraphic unit containing hot groundwater is the Latrobe Group. Groundwater temperatures in the range 30 to 70¦C have been recorded from depths between 500 and 1000 m. The hottest groundwater is in the Latrobe Valley and Lake Wellington depressions. Geothermal gradients in these areas range from less than 2¦C/100 m to over 10¦C/100 m (compared to a world average of about 3¦C/100 m). A number of theories have been advanced to explain the geothermal anomalies including exothermic reaction such as oxidation of coal, mixing with deeper, hotter groundwater and high geothermal fluxes along fault zones. Variations in geothermal gradients can also result from type and thickness (and hence thermal conductivities) of the sedimentary pile, depth to consolidated basement rocks, and influence of groundwater flow patterns including proximity to recharge zones. The hot groundwater in the Gippsland Basin has substantial potential as a source of energy for direct heat applications such as process heating, space and water heating for buildings, and agricultural and aquaculture. Geothermal energy has a number of environmental advantages over traditional sources of energy. It is clean, safe, causes minimal land disturbances and in most cases is naturally renewable.

Jan 1, 1992

By T F. Guerin

Explorationn and mining have shown to cause significant impacts to the terrestrial and marine environment. Current mining and exploration techniques are outlined in the light of their potential to impact upon the environment, ie negligibly, negatively or positively. A profile of five Australian-based gold producers is presented. The development of protocols to specifically deal with the highly regulated and ever changing, mining and environmental legislation. demonstrates mining companies can successfully opcrationalise the concept of sustainable development.

Jan 1, 1992

The Modified Zincex® Process, developed by Técnicas Reunidas, is highly flexible dealing with a wide range of pregnant leach solutions. No matter if those solutions are produced from primary or secondary raw materials, and/or are based on conventional leaching, pressure leaching, heap leaching or bio leaching the result is always high-purity zinc product. The zinc solvent extraction unit within the process is a very effective barrier for impurities and a buffer for the composition of the pregnant liquor. This unit achieves an extremely pure aqueous extract that can be converted into different final products. All of them are characterized by fulfilling the highest purity standards. Also, there is the possibility to adapt the global process to a wide range of pregnant liquor compositions and various production capacities up to a zinc production limit over 150 000 t/a with a single solvent extraction plant.

Jan 1, 2002

By Lee T. J

The area, A, under a gamma-ray log that passes through a horizontal bed given by: A = gl/k. Here is the equivalent concentration of U3O8 in the body, l the thickness of the body, and k the calibration factor or sensitivityof the logger. The area is independent of the logging speed or logger time constant.This relationship, together with the first moment about the maximum of the log and its value there suflicient to determine the thickness, position of the centre of the bed from the log maximum and the concentration of U3O8.Numerical results obtained from artificial and field data show that the computed results arc as good as those obtained by methods such as the inverse filter technique and the iterative method. The present method yields results that arc easier to feed into an ore reserve data base.

Jan 1, 1981

By Manuel Arnáiz, Pedro R. Sola, Rogelio Baudot, Manuel Herrera, Carlos S. Oteo

The aim of this paper is to describe and analyze the ground treatment performed between January and May 2002 in order to increase safety during excavation and reduce instability problems along 180 m of tunnel, during the construction works associated with line 10 extension to the Madrid Metro. The tunnel was excavated using the traditional Madrid Method and in the section considered in this paper layers of sand were detected around the tunnel crown area with a significant presence of water, the in?ow of which needed to be controlled with a minimum impact on the surrounding environment.

Jan 1, 2003

Effect of Anionic Surfactant on Silica Particle Attachment at the Oil-Water Interface Controlling particle attachment is crucial where powdered solids come into contact with oil and water. Particles are trapped in a deep energy well at the oil-water interface, stabilising emulsions. Here it is shown that adding anionic surfactant causes dramatic changes to the bulk and interfacial structure of silica particle-stabilised oil-in-water emulsions. Exposing particle-stabilised drops to surfactant concentrations above the critical micelle concentration enhances the rate and extent of creaming and flocculation. Mixing particle-stabilised emulsions with surfactant solutions causes drop fragmentation. As the surfactant concentration increases, the average drop size decreases and particles are displaced from the interface during the mixing process.

Sep 13, 2010

By G. Tranell, L. Kolbeinsen, S. Gaal, J. Safarian

The effect of carbon material properties on the rate of MnO reduction from ferromanganese slag by solid graphite was investigated. A sessile drop technique was used to study the reduction rate of a synthetic slag containing 45 wt% MnO at 1500 and 1600 ºC. Different types of graphite substrates were used and the con-tact angle between slag droplets and substrate were measured in-situ. Moreover, the slag droplet volume during the interaction with the graphite substrates was calculated and normalised. The mathematical relationship between the slag density during the reduction and the normalised slag droplet volumes during the reduction were derived and the MnO reduction curves were then calculated. A method for measuring the slag reactivity of solid carbon was defined and used to qualify the propensity of the different graphites to react with the liquid slag. Some supplementary studies such as manganese evaporation measurement and EPMA analysis for determining the extent of MnO reduction were also carried out. It was observed that there is nota significant difference in the wetting angle of the graphite substrates by the slag, and the wetting is not changed within the temperature range of 1500-1600ºC. However, the changes in the contact angle during the slag reduction at 1600ºC are more than at 1500ºC. The kinetics of MnO reduction is dependent on the type of graphite and it is more dependent on the graphite properties at lower temperatures. On the other hand, the dominant properties of graphite on the reduction rate vary with temperature. A multivariate analysis on the graphite properties and the parameters related to the slag reactivity indicated that the kinetics of MnO reduction is mainly dependent on the temperature, and then on the graphite properties. It was also found that at1500 ºC the surface area and the CO2 reactivity are the most important graphite properties for the slag reduction, suggesting that the reactivity of carbon is rate controlling at 1500 ºC. However, the porosity related parameters are the most important graphite properties at 1600 ºC, suggesting that CO gas desorption is rate controlling at high temperatures.

Jan 1, 2007

By Steve Chorley

Open-type, or main beam, tunnel boring machines (TBMs) can achieve impressive rates of production. This type of TBM typically outperforms other types of TBMs currently in use around the world. In good ground conditions, main beam machines have achieved production rates of more than 1 km/month (0.6 miles/month). However, installing effective ground support in poorer rock conditions on main beam machines can be a major cause of concern. The design of main beam machines is such that installation of ground support equipment, particularly at the front of the machine in what is commonly known as the L1 support zone, has traditionally been limited to rock drills and basic working platforms. Personnel working in the L1 zone have, until recently, been protected by roof supports and extended fingers, often with restricted access to working areas.

Jan 1, 2011

By Peter Metcalfe

"Wireless communication in the mineral processing environment is not as simple as it is in the home or office environment. The correct design of a wireless network in the mineral processing environment can offer a more flexible and lower cost installation than the transitional fiber networks. However with the flexibility of a wireless solution, also comes some limitations. By reviewing the plant requirements along with weighting the wireless benefits and limitations it is possible to design a network that combines the robustness of a wired solution with the mobility of a wireless solution. This paper addresses some wireless design considerations and it looks at some real life examples in the following areas: •,Meshed wireless network for high levels of redundancy •,Wireless instruments (such as HART, Modbus and others) •,Portable devices for mobile operators •,Network monitoring for plant personnel (it’s no longer just for IT people) INTRODUCTION Typical networks used in the mineral processing environment consist of a fiber network infrastructure with industrial switches used to connect the network devices. These fiber networks can be redundant or put into a ring topologies to offer a higher level of availability. Fiber networks have the benefits of: •,Immunity to noise from power and grounding issues •,Ability to span long distances (2km for multimode fiber and 20km for single mode fiber) •,Maintainable “off-the-shelf” technology Fiber networks however have some drawbacks, such as: •,Relativity high initial installation cost for cable trays, poles, trenches and pulling and termination of cable. •,Fixed geographic topology, adding future fiber drops may be challenging and expensive. •,Mobile users are not considered. Integrating a wireless network with a fiber network can offer the best of two worlds, a reliable high speed backbone for mission critical activities and a wireless network for remote applications and mobile users."

Jan 1, 2014

By N. V. Nayak

Maharashtra State Road Development Corporation Ltd., has initiated a scheme for construction of 55 flyovers in Mumbai in India. To ensure speedier completion of projects several new technologies were adopted to save time without compromising on safety and reliability. Many of the flyovers involved large diameter pile foundations carrying loads ranging from 3500kN to 1375kN. Significant time would have been lost in using conventional load testing procedure to check pile capacity apart from the difficulty in mobilizing the load and the obstruction to site movement and traffic on the adjoining roads. High Strain Dynamic Testing was introduced on the project sites in lieu of static load testing after conducting numerous co-relation studies on various project sites. A total of seven co-relation studies have been conducted till date and based on these data static testing has been replaced by dynamic testing on numerous flyovers. The paper presents the results of such studies. CAPWAP analysis was also conducted on the data to evaluate the percent skin friction and end bearing so as to improve future design parameters.

Jan 1, 2000

By K D. Wilkes

The WEMCO Heavy Media Drum Separator was first introduced by WEMCO in California in the 1940`s, initially from their base in San Francisco and later when the company moved to Sacramento. The WEMCO Company became a part of EIMCO Process Equipment in 1985, and in 2002 EIMCO became a part of the GL&V Group when Dorr-Oliver EIMCO was created. Throughout this period of time the WEMCO Drum has been installed on a variety of different applications and is now operating at the heart of many of the world?s largest Minerals and Coal Processing Plants, as well as being used by many smaller producers and metal re-cycling operations. This paper looks at the practical aspects of using WEMCO Drums in a representative range of processing applications.

Jan 1, 2006

By K. N. Santini, J. M. Barker

The perlite industry in the United States continued to undergo rapid change and increased competition last year as it did in 2002. U.S. production in 2004 was 510 kt (562,000 st),an increase following five consecutive years of decline (Table 1). Perlite is exported to Canada and to the Pacific Rim. These partially offset imports. Perlite imports from Greece to the eastern and Gulf Coasts of the United States declined by about 22 percent after reaching a record 240 kt (264,000 st) in 2003.But their market remains protected by high rail rates from western U.S. plants. Minor imports of perlite persist by Termolita from Mexico.

Jan 1, 2005

By H. G. Oltmann

The equilibrium nitrogen solubility in the CaO-SiO2system was studied by a slag-gas equilibration technique, in graphite crucibles at 1823K under a CO-N2 atmosphere. The nitrogen content of the slags was determined by the Kjeldahl method. A reliable technique was used to obtain an initial nitrogen content in the master slags, from the addition and pre-melting of silicon nitride. Reduction of silica by graphite was found to occur during the equilibration experiments, resulting in compositional changes of the slags. The results were extrapolated to equilibrium by kinetic evaluation of the data. The nitrogen solubility showed good agreement with the result of Suito and Sano, while Fruehan?s results were lower. However, the results of the present study do not support the maximum nitrogen solubility values found by Sano.

Jan 1, 1999

By J. N. Van der Merwe

The current state of the South African mining industry is briefly reviewed from the point of view of an engineer not schooled in the finer details of predictive economics. Based on the assumption that current world exploration targets are indicative of which commodities the world will want in the future, it is concluded that the South African mining industry will continue to be viable and growing well into the future. South Africa holds the minerals the world wants and needs, and as long as the world has people, the demand for those, including gold, will continue to grow. There still is a growing demand for vanity commodities' and even the demand for platinum as a jewellery material displays significant growth. Mine safety still needs to improve, but significant improvement has already been made although the industry is not always acknowledged for the effort in this field. The safety target set for 2013 is within reach but will require sustained effort. The physical mining conditions for the main revenue earners, coal, platinum, and gold, will change substantially in the near future. Research in mining has declined alarmingly and it is urgently necessary for that to be revitalized to generate the knowledge that will be required. In order to streamline the transfer of knowledge to the mining engineers of the future, research needs to be conducted with the full involvement of the universities. It will also be necessary for the universities to continually review curricula to incorporate the latest knowledge and to embark on a campaign of knowledge transfer to the older generation of mining engineers. The mining industry is well supported by the universities, who have done their duty with regard to societal transformation, and the universities are in turn supported by the industry through vehicles like the METE Industry is also strongly supported by a number of professional and vocational societies. The SAIMM will continue to play its vital role as the meeting point of the mining technical sciences, and will continue to disseminate knowledge via the journal, schools, and conferences. In the future, it will review its modus operandi to support the needs of growing membership in the remote branches. It will enter the research arena in an appropriate manner and give effect to the developing integration of mining and society. The most important threat to the future of the mining industry is the recurrent mention of nationalization. While interaction between the mining industry and political and economic development of South Africa has always been characteristic, the current debate is emotional more than rational, and engineers are not well equipped to participate. This matter needs to be finalized before it becomes a popular force that politicians cannot control.

Jan 1, 2011

By A. Yazadni-Chamzini

Considering the nature of open pit mines, harvest volume, it usually is required to remove a lot of waste to access to mineral planned grade. So, one of the most important part of open pit mines design, is waste dump site selection. Many factors are effective in waste dump site selection. These factors are sometimes in conflict with each other. So selecting the desired location for waste dump is a process complex and multi-criteria decision making. There are a variety of methods for decision making under complicated condition, such as fuzzy, Delphi, multi-criteria decision making and Expert system methods can be hinted. VIKOR method, which is one of the decision making multi criteria methods, is useful tool for decision-making. On the other hand with regard to uncertainty in decision-making, fuzzy approach is a useful tool for this purpose. This article has tried to select the best waste dump site in Sari Gunay Gold Mine by Fuzzy VIKOR. The results show that C position has a higher priority than other positions.

Jan 1, 2012