Search Documents

By Freeman C, Dingley W

Addition of sodium nitrite-borax, sodium hydroxide, sodIUm carbonate, lime, or sodium silicate reduced wear of forged steel balls and cast iron slugs in wet grinding a complex zinc-lead-copper sulphide ore in laboratory ball mills. Maximum wear reductions were 27 per cent (forged steel balls) and 33 per cent (cast iron slugs) with sodium hydroxide and nitrite-borax additives respectively.Potential measurements of balls and slugs during grinding, and analysis of the data in terms of corrosion theory demonstrated that corrosive wear had been reduced or prevented by these additives. Actual per cent wear reductions were not equated to the rate of corrosive wear because of the undefined interdependence between abrasion and corrosion in wear processes. The investigation verifies that in laboratory ball mills corrosion is significant in the wear of grinding media and wear can be reduced by corrosion inhibition and pH adjustment.

Jan 1, 1978

By L. C. IlsLey

"There is an old saying that ""It is too late to lock the stable after the horse is stolen"". Is not this just what is being done by many mine operators today when it comes to buying safe electrical equipment for gaseous and dusty coal mines?The ""open type"" of electrical equipment or even the ""half safe"" type represents the unlocked stable. After the mine disaster, and after men have lost their lives, the lock is put on - that is, safer equipment is installed.For example, an open type of electric coal drill was used in a gaseous mine in West Virginia, This was the probable cause of the death of 27 men. A half safe type of electric coal-cutting machine was used in a gaseous mine in Pennsylvania. This was likely the cause of the death of 36 men. An unapproved, unsafe type of flame safety lamp was used in a gaseous and dusty mine in Utah. This was the all¬eged cause of the death of 171 men. All three disasters happened within the last six months, and seem to have been avoidable if proper equipment had been used.It is understood that more rigid requirements will be enforced in West Virginia. The committee of State mine inspectors made definite recommendation for im¬proving the conditions in the given mine in Pennsylvania. The Industrial Commission of Utah have already issued new orders which will remedy the use of unsafe lamps in that State.These acts and recommendation are all good and will help prevent accidents in those States in the future. Is it not a pity that such recommendations and order were not made a little earlier before the tell of life had been exacted? Is it not a pity that other States will not take these lessons to heart and safeguard their mines before and not after disasters take place?Electric current can cause accidents in five general ways as follows: (1) By shock to persons; (2) by igniting powder; (3) by igniting gas; (4) by igniting coal dust; and (5) by setting fire to inflammable material such as timber and coal. A great many accidents from these causes are preventable if proper care is taken. Most of the accidents caused by sparks and flashes from electrical apparatus would not take place if approved electrical equipment was used. By approved equipment, the writer means equipment that has been tested and formally approved by the Bureau of Mines. So far as known, up to the present time, no disasters have been caused by sparks or flashes from equipment having the Bureau's approval."

Jul 1, 1924

It is predicted that vast volumes of affected mine water will be produced by mining activities in the Mpumalanga coalfields of South Africa. The potential environmental impact of this excess water is of great concern in a water-scarce country like South Africa. Research over a period of more than 10 years has shown that this water can be used successfully for the irrigation of a range of crops (Annandale et al., 2002)1. There is, however, continuing concern from the local regulators regarding the long-term impact that large-scale mine water irrigation may have on groundwater quality and quantity. Detailed research has been undertaken over the last three years to supplement the groundwater monitoring programme at five different pilot sites, on both virgin soils (greenfields) and in coalmining spoils. These sites range from sandy soils to very clayey soils. The research has included soil moisture measurements, collection of in situ soil moisture over time, long-term laboratory studies of the leaching and attenuation properties of different soils and the impact of irrigation on acid rock drainage processes, and in depth determination of the hydraulic properties of the subsurface at each of these sites, including falling head tests, pumping tests and point dilution tests. This has been supported by geochemical modelling of these processes to quantify the impacts. The results indicate that many of the soils have considerable attenuation capacities and that in the period of irrigation, a large proportion of the salts have been contained in the upper portions of the unsaturated zones below each irrigation pivot. The volumes and quality of water leaching through to the aquifers have been quantified at each site. From this mixing ratios have been calculated in order to determine the effect of the irrigation water on the underlying aquifers. Keywords: coalmines, irrigation, gypsiferous mine water.

Jan 1, 2009

By Jan E. Nesset, James A. Finch, Frank Rosenblum, Rebecca Payant

"Under certain conditions of moisture and oxygen, sulphides can spontaneously heat, a phenomenon known as self-heating. In this paper, we test a hypothesis that galvanic interaction between some sulphides can promote self-heating. Galvanic interaction is controlled by restpotential difference between minerals and their surface area of contact (particle size). In order to decrease rest-potential, four sulphides were tested: pyrite, chalcopyrite, sphalerite and galena. Two series of samples consisting of mixtures of two sulphides, each representing a mass fraction of 50 %, were run in standard self-heating tests. The first series comprised five mixtures, two with low rest-potential difference (pyrite-chalcopyrite and chalcopyrite-sphalerite) and three with high rest-potential difference (pyrite-galena, chalcopyrite-galena and pyrite-sphalerite). The second series was performed on a pyrite-sphalerite mixture at four particle sizes (80 % passing 850 µm, 300 µm, 75 µm and 38 µm). The first series showed that the individual sulphides and the mixtures of low rest-potential difference did not self-heat but the mixtures of high rest-potential difference did self-heat. The second series showed that self-heating increased inversely with particle size (increased specific surface area) and revealed that it was the fineness of the pyrite (high rest-potential sulphide) that governed the self-heating effect, indicating the rate-limiting step is the reduction reaction on pyrite (cathodic mineral). The increase in self-heating with high rest-potential difference and increasing particle fineness supports the hypothesis that galvanic interaction contributes to sulphide self-heating. A possible mechanism based on the hydrogen sulphide hypothesis is proposed where the reduction reaction at the cathodic mineral surface is ferric to ferrous. The understanding gained will be of interest to those involved in storage, shipping and disposal of sulphide minerals.INTRODUCTIONSulphide mineral ores are the major source of most base metals such as copper, zinc, nickel and lead. Once the ore is extracted, the sulphide minerals are liberated by size reduction (crushing and grinding), concentrated by flotation, and the concentrates sent for further processing to extract the metal (smelting and refining). At the various stages from mining to concentrate shipment and tailings storage, the sulphides are exposed to a variety of environments, which under certain conditions of air (oxygen), humidity and temperature can cause them to heat. Since no external heat source is involved, this pyrophoric process is known as spontaneous heating or, more commonly, self-heating. The self-heating of sulphides is associated with oxidation reactions under moist conditions. If the heat generated is greater than the heat dissipated, the sulphides will self-heat and the material temperature will rise. This can make working conditions potentially dangerous as oxygen is consumed from the surrounding air and significant quantities of sulphur dioxide (SO2) can be released (Ninteman, 1978)."

Jan 1, 2011

By M. Wasel

The Gross Rosebel gold deposits are located in the Guiana Shield of north central Suriname. Initial discovery of surficial gold in 1880 by local artisanal miners preceded small-scale mechanized mining from 1885 to 1939. The first systematic exploration program was carried out by Placer Development from 1974 to 1977. In May 1992 Golden Star Resources optioned the property. Initial shallow reconnaissance diamond drilling of the extensive surface geochemical anomalies intersected sporadic gold mineralization with no apparent continuity between drill sections. Successive deep augering, trenching and systematic grid drilling based on information from surface mapping allowed development of a preliminary geological model. Further drilling of specific structural-lithologic targets and more complete synthesis of geological data from the trenching and deep auger sampling added to the geological model and defined the multiple controls of gold mineralization. Carefully planned infill drilling on a tighter grid spacing resulted in progressive definition of reserves within six discrete gold deposits. In a complex geological setting, the key to success at Gross Rosebel was persistent, systematic exploration, detailed mapping, careful core logging and perceptive geological interpretation. Reserves now stand at 48.6 Mt at 1.6 glt Au, or 2.4 million ounces of gold. The purpose of this paper is to describe the progression of exploration activity that led to the definition of substantial gold reserves and to summarize the geology of the deposits.

Jan 1, 1998

By Matthias Pulsfort, Markus Herten, Rolf Breitenbücher, Claudia Fierenkothen

"Secant bored pile walls are frequently used as retaining walls in watertight excavations to cut off ground water aquifers and are subsequently exposed to ground water pressure loading in addition to earth pressure loads. To avoid extra loading from ground water pressure in soils with limited permeability, it can be useful to arrange drainage windows within secant bored pile walls by means of single primary piles filled with porous concrete without reinforcement cages, which usually have to be placed within casings in submerged conditions. This concrete may serve as a horizontal arch between the reinforced secondary piles, but it must however enable vertical draining between load carrying construction beams and the bottom of the excavated pit. In the present submission, the results of several material tests with different mix designs of porous concrete with certain admixtures are presented together with first and important experiences with a wellsuited placement technique for porous concrete casings in small- and large-scale laboratory tests. It can be shown that the usual placement technique of employing a tremie pipe is not suited for this type of unsaturated concrete. Instead, pouring with a particular kind of cone and an open conductor pipe has proven successful.Additionally, special testing methods are currently developed for judging the suitability of the desired concrete mix design in preparation for an upcoming real-scale experimental pile installation in Germany.1. INTRODUCTIONRetaining walls are often built as secant bored pile walls in order to cut off aquifers saturated with groundwater against deep building pits. In soil types with relatively low permeability, however, seepage flow may be permitted, because the quantity of groundwater to be pumped is limited, and the range of influence due to dewatering is not reaching far. Thus, the hydrostatic water pressure on the retaining wall can be considerably reduced, leading to a more economic design (see Fig. 1).In unsaturated soils, the dewatering effect can be achieved by means of porous pervious concrete with a uniform grainsize distribution of aggregates typically placed in a borehole under dry conditions. With regard to the use of porous concrete to be placed at the ground surface in road pavement applications, experience is sufficiently available as shown, for instance, by Neithalath et el. (2010). However placing the porous concrete in a bored pile using a tremie pipe under submerged conditions is a challenge and a completely new approach, because there is a considerable risk of segregation of the fresh concrete, separating the cement lime paste from the aggregates when in contact with water and leaving only neat gravel on the one hand as well as a tight cemented area at the bottom of the pile on the other hand. If this concrete placement is successful, additional dewatering by means of extra wells behind the retaining wall can be avoided. Of course the seepage flow in the adjacent soil needs to be regarded seriously."

Jan 1, 2017

By D. Van Tonder, C. Edwards

ABSTRACT Solvent extraction is used in many acid leach uranium circuits to upgrade and purify the uranium-bearing solution prior to final product precipitation. A number of strip options are available to recover the uranium from the loaded organic. This paper compares seven of these options on the basis of typical capital and operating costs for the solvent extraction circuit and downstream uranium processing and also considers other related issues. The aim is to provide an objective comparative assessment of these options that could be used as a qualitative guide in process selection or improvement.

Jan 1, 2013

By J. C. Reid

Pre-cambrian scheelite deposits in Northeastern Brazil are widespread in a high grade metamorphic terrain. Previously these deposits had been interpreted as contact-metasomatic. In this paper, a volcanigenic model is invoked based on the volcanic setting (proximal to distal) and the absence of associated felsic intrusives and spatially associated metasomatic skarns. The tungsten was introduced into sediments by volcanic- exhalative processes and subsequently remobilized and further concentrated by heat and metamorphis fluids associated with high-grade metamorphism and migmitization. An alternative syngenetic - diagenetic model is discussed which requires the transport of tungsten by heteropoly acids and deposition of the tungsten as a function of Eh and Ph conditions and different clastic depositional environments. While such stratabound tungsten deposits are considered rare in North America, the hypotheses developed in this paper may open new areas for exploration.

Jan 1, 1983

By Charles Stone, Hannes Lagger, Dru Desai

The design methodology of the planned Second Avenue Subway Project (SAS) led to development of the initial support design to estimate cost and quantities in the Preliminary Engineering (PE) stage. Careful selection of the cavern design rules that recognized the impact of rock quality, rock cover, excavation geometry, and excavation sequence helped to overcome the design challenges of large, shallow caverns for the initial ground support. In the course of the design verification process prescribed by the design methodology, the design team was continuously reviewing and updating the support quantities. The design procedure includes methods using different approaches of empirical, continuum, and discontinuum analyses, which are currently advanced in the Final Engineering (FE) stage. The paper is a continuation of the RETC 2005 “Trials and Tribulations” and focuses on the procedures that led to the changes in the initial support as a result of the ongoing design development.

Jan 1, 2007

By D. F. Hambley

This report documents the work carried out by Engineers International, Inc. and its subcontructor, W. G. Pariseau, in order to develop a design manual for ore passes for open pit mines. The work included an extensive information search, novel analyses in rock flow theory, cost and time estimation for shaft and raise construction methods, and development of design criteria for the are pass proper, dump point, and draw point.

Jan 1, 1983

By B C. Sarkar, D Ray, V Sarkar, P K. Sinha, R K. Singh, A Kumar

Estimation of iron ore grade distribution has been attempted using geostatistics and artificial neural network (ANN) based models for a banded iron formation (BIF) type iron ore deposit of East India. Geologically, it is a supergene iron ore formation through an enrichment process of parent material (BIFs) by gradual leaching of impurities, namely SiO2 and Al2O3. As the degree of leaching differs spatially, distribution of Fe varies depending on local controls of ore formation. While geostatistical methods work on models based on spatial correlations of mineralisation parameters, ANN models a non-linear distribution and is widely used as a global approximator. Spatial distribution modelling of Fe values has been carried out employing ordinary kriging (OK) and sequential Gaussian simulation (SGS). Non-linear modelling has been performed using hybrid neural networks (HNN) that provided an alternative option for grade estimation. Classical statistical modelling revealed a negatively skewed 3-parameter lognormal Fe population having a mean of 60.49 per cent with a skewness of -0.08 and a kurtosis of 2.60. Semi-variography and geostatistical estimation employing OK procedure led to block-by-block kriged estimates with associated kriging variance, which provided an overall mean kriged estimate and kriging variance of Fe as 60.29 per cent and 7.76 (per cent)2 respectively. SGS procedure revealed a mean of 60.71 per cent and a standard deviation of 5.89 per cent with minimum and maximum values as 45.12 per cent and 68.70 per cent respectively in respect of Fe. HNN model provided values of mean squared error (MSE) and correlation coefficient (R2) as 12.33 and 0.61 respectively, thereby exhibiting the robustness of the model to sustain maximum heterogeneity within the target domain. A comparison of Fe grade estimates obtained by kriging, simulation and HNN models more or less maintain similar distribution patterns that are close to the sample data. It is thus opined to carry out the grade prediction exercise employing all these three modelling approaches to obtain alternative scenarios for improved mine planning and design exercises. The techniques provide a foundation for cogent grade modelling leading to improved iron ore reserve estimation procedures.CITATION:Sarkar, B C, Singh, R K, Ray, D, Kumar, A, Sinha, P K and Sarkar, V, 2017. Iron ore grade modelling using geostatistics and artificial neural networks, in Proceedings Iron Ore 2017, pp 431–438 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By D J. Black

The process of longwall coal extraction coal causes fractures in the overlying and underlying strata and these fractures become pathways for gas released from adjacent coal seams to flow into the mine workings and contaminate the ventilation air. If the rate of gas emission exceeds the diluting capacity of the ventilation air, the gas concentration will increase and exceed the statutory limit resulting in production delays.All potential gas sources within the planned mining area, including coal seams located above and below the working seam, should be identified and sufficient gas data collected and used to determine the specific gas emission from each gas source. Gas reservoir and emission modelling is recommended to determine specific gas emission and changes in gas emission from individual sources over the planned mining area. Accurate gas reservoir and emission modelling provides the information required to accurately design gas drainage programs to effectively manage gas emissions and minimise the risk of ‘gas-outs’.Given the increasing occurrence of incidents of gas concentration in ventilation air exceeding the 2.0 per cent statutory limit and changes to mine plans to avoid ‘difficult-to-drain’ areas, it is apparent that many operations are not effectively utilising gas reservoir and emission modelling to identify high gas emission areas and are not completing sufficient gas drainage in advance of planned mining.The process of gas reservoir and emission modelling to support gas drainage design to control tailgate gas concentration and fugitive emissions is presented and discussed.CITATION:Black, D J, 2017. Gas reservoir and emission modelling to evaluate gas drainage to control tailgate gas concentration and fugitive emissions, in Proceedings Australian Mine Vent Conference 2017, pp 65–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

Development of New Comminution Testing Methodologies for Geometallurgical Mapping of Ore Hardness and Throughput The emerging discipline of 'geometallurgy' is becoming increasingly recognised as a discrete and high-value activity that reflects an ongoing trend towards more effective mine site integration and optimisation. Constrained sampling that reflects and defines inherent ore body variability is a key geometallurgical requirement. This requires use of larger numbers of low-cost physical testing which can be applied to small sample volumes suitable for defining natural variability. The AMIRA P843 'GeMIII' project (Geometallurgical Mapping and Mine Modelling) is a major industry-supported research initiative designed to develop new tools, methods and protocols to support geometallurgical integration. As part of this integrated research a new more rapid low-cost comminution test (GeM Comminution index) has been developed which can be employed as a front line tool for geometallurgical mapping purposes and predictive throughput modelling. The test has been designed to be inserted into routine assay sample preparation and is based on constrained jaw crushing protocols linked to analysis of resultant size distributions. Extensive validation and modelling has shown the GeM Comminution Index (Ci) is correlated with the Drop Weight index A*b and Bond Mill Work Index (BMWi). Large scale trials have been conducted within a commercial assay laboratory to demonstrate and optimise incorporation of the Ci test into routine sample preparation protocols. While Ci based estimates of A*b and BMWi are not as precise compared to larger volume more expensive test-work, the ability to undertake large numbers of tests typically in a systematic down-hole manner, provides a high level of data support through adjacency. A Ci based approach is highly suitable for variability mapping, domaining and selecting large composite samples for more precise testing. Within the context of the AMIRA P843 project this forms part of an integrated work flow designed to support geometallurgical integration. The development of a comminution test linked to routine assay sample preparation represents significant value adding to a process that in most cases is already going to be carried out. This paper introduces the Ci test concept and application to geometallurgical testing for throughput modelling

Sep 13, 2010

There is no doubt that the mining sector is considered to be the backbone of many countries. Furthermore, it has played an important role in the prosperity of nations, whether developed or developing. Saudi Arabia is one of these countries that has a large variety of metallic and non-metallic mineral resources that range in size and value occurrences of limited potential to deposits large enough to sustain profitable exploitation. Therefore, the Saudi government needs to reinforce the capacity of the sectoral institutions to better regulate and promote the sustainable development of the sector. The ability to overcome the administrative and legal complications that constrain private sector participation in the minerals sector, through new mining code which will streamline the procedures for obtaining licenses and will add more predictability and transparency to the application process, are proposed for increasing the sustainable development. This paper will outline how the Saudi government is tackling the major challenges that face the minerals industry. This paper provides the background to the Saudi Arabian mineral sector and its industrial base. Finally, the paper identifies the problems and constraints that face the minerals sector in Saudi Arabia and provides an assessment of the effects of government policies and planning efforts in the minerals sector, particularly during the period of the development plans which started in 1970.

Jan 1, 2009

By Samuel A. Reipas

Introduction The ore mining industry has been successful because of technological progress and huge sums of capital investment. But new technology and plants have not come cheap. The problem now is companies will run out of money before they run out of ideas. Survival Strategies Industry survival strategies demand restructuring and new plans. Inland's prescription for the future includes: • Continued emphasis on technological improvements to upgrade pellet quality and lower costs; • Effective use of human resources resulting in employee satisfaction and improved planning and productivity; • Deliberate, well planned, and documented cost-control programs for the short- and long-term; and • Capital investments to support the first three initiatives. Technology Technological changes are not only required by the need for operational improvements, but by product quality improvement dictated by the user - usually the blast furnace operator. Established ambient measurements of pellet quality, such as tumble index, compression strength, porosity, size distribution, and chemical composition, are no longer considered meaningful in predicting pellet performance in a blast furnace. New specifications, called low temperature and intermediate temperature properties, have been recently introduced. Low temperature specifications are characterized by disintegration of pellets in the 500°C (930°F) range in the upper portion of the granular zone during the hematite-to-magnetite transformation in blast furnace stack. Intermediate temperature properties (measured by 1000°C or 1800°F) are characterized by swelling, reducibility, and compression strength after reduction, reflecting conditions in the lower portion of the granular zone of the furnace. These new parameters are being used for pellet quality evaluation at Inland, and will be introduced at its Minorca mine for more routine analysis and correlation with the pellet furnace operation. With increased emphasis on quality, effective communication between the blast furnace operator, research, and the pellet plant operator is critical. At Inland, this is accomplished through technical meetings where the opportunity is provided to solve problems, establish a common understanding on the value of quality, and develop future quality standards and programs. With the degree of sophistication in determining pellet quality as it affects blast furnace operation, the future pellet plant operator will actually be producing a custom pellet. Human Resources Technological change has been a strong point at Inland, and will continue to be. However, human resource management is equally important. Is management giving sufficient attention to employee motivation and involvement? It is a way to improve productivity, reduce costs, and enhance employee job satisfaction. The industry is beginning to understand the principles and the potential for tapping employee brainpower. The payoff can be handsome. Management has to be willing to share both information and power if participative management is to live up to its potential. It has to become more flexible and be willing to adapt to change on the human side. Management should embrace rather than fear employee involvement. Given time, joint problem solving will replace adversarial attitudes and pay dividends for both sides. Productivity and product quality will improve and new dimensions of employee job satisfaction will be achieved. But, it will not happen overnight. Attitudinal change must permeate the organization from top to bottom. This change is needed to support the working relationships and give everyone a sense of direct and meaningful involvement.

Jan 11, 1983

Amid some of the worst economic conditions that the mining industry has been faced with in more than a decade, the mood among the large crowd at the 114th Annual Northwest Mining Association?s annual meeting was surprisingly upbeat. More than 2,200 attendees showed up at John Asuaga?s Golden Nugget Casino in Reno, NV for the conference held Dec. 1-5. And more than 200 companies exhibited in 240 spaces, including SME and the Minerals Information Institute. The number of attendees and exhibitors were the most for the conference in more than 10 years. The conference was held in Reno/Sparks for just the second time in its illustrious history but began under the cloud of global financial turmoil. Prior to, and during the conference, the industry news headlines were grim, to say the least. An alarming number of mine plans and expansions had been put on hold; hundreds of miners across the United States had been or were in the process of being laid off; commodity prices were falling and some of the biggest mergers in the industry fell through while miners around the world put the brakes on to take a wait-and-see approach. It was a painful time for many, but the downsizing actions taken by many mining companies was exactly what needed to happen, according to Industry Outlook Luncheon featured speaker Frederick Sturm. He is the executive vice president and chief investment strategist and member of Mackenzie?s Investment team. He has earned a reputation as one of Canada?s leading investors in natural-based companies and he also manages the Ivy Global Natural Resource Fund in the United States Sturm said that the mining industry has fallen hard and that he expects it to bounce back quickly, before falling hard again. In these tough times, he said, the companies that have pulled back on production early are doing the right thing in the long run.

Jan 1, 2009

By D. M. Walters

To achieve safe and healthy working conditions in shaft sinking operations, ventilation, and where necessary cooling, must be provided. These requirements are considered for sinking vertical, sub-vertical and decline shafts. Regulatory requirements, determining air volumes and amount of cooling required, the various ventilation methods used such as force, exhaust, twin columns, air reversal using four gate systems and the equipment required to achieve this, are discussed. Consideration is also given to the sinking of single and twin declines using diesel equipment, calculating the air volumes required to dilute pollutants and the various methods for achieving this. Also discussed is the importance of having early ventilation design input to the overall design of the mine. In many cases ventilation can be the prime determinant for the size and configuration of the shafts or declines that have to be sunk.

Jan 1, 2009

By A. Sobhy

Froth flotation is a widely used, cost effective coal cleaning process. However, its high process efficiency is limited to a narrow particle size range between approximately 50 to 600 µm for coal and 10 to 100 µm for minerals. Beyond this range, the efficiency of froth flotation decreases sharply, especially for difficult-to-float coal fines of weak hydrophobicity (e.g., oxidized coal). This study was aimed at enhancing recovery of an Illinois fine coal sample using a flotation column featuring a hydrodynamic cavitation nanobubble generator. Nanobubbles that are mostly smaller than 1 µm can be formed selectively on hydrophobic coal particles from dissolved air in fine coal slurry. Results indicate that combustible recovery of a -150 µm coal was increased by 5-50% for different size fractions in presence of nanobubbles, depending on process operating conditions. Other major advantages of the nanobubble flotation process include lower collector dosage and air consumption since nanobubbles are produced from air naturally dissolved in water and they act as a secondary collector on particle surfaces, thereby resulting in considerably lower operating costs. Key words: Cavitation; coal; froth flotation; nanobubble.

Feb 27, 2013

By Moresby J. F

Segregation roasting was used to recover more than 85 per cent of copper from crushed, minus 14 mesh refractory furnace-lining bricks. A plus 14 mesh fraction: which was high in copper, could be recycled directly to the smelter, giving an overall recovery of approximately 90 per cent. An oxidation roast at about 700°C was necessary, before segregation roasting, to convert copper sulphides and copper metal to sulphates and oxides. Withsegregatron temperatures in the range 600°-650°C the quantities of solid carbon and NaCI required are 2-5 per cent and 1 per cent respectively. P.V.C. coating from scrap copper wire can be used instead of NaCl as asource of hydrogen chloride for the segregation reaction.

Jan 1, 1978

The 8 ft by 91/2 ft drive which joined No. 7 Shaft with Browne Shaft on the 1,480 ft level was extended from both ends and met at a point approximately 12,000 ft from No. 7 (2,000 ft from Browne).The surveying required for this 2 1/2 mile haulage drive called for greater accuracy than was obtainable from South Mine standard methods. Procedures and devices from published information were tried and modified as required to suit local conditions. Several new methods were applied and improved as the drive advanced. The control of angular, linear and level measurements was perhaps considerably in excess of the requirements, but this was offset by abnormally large discrepancies resulting from shaft plumbing. The accuracy of the final breakthrough, although not to the standard desired, was sufficient to complete the connection without inconvenience and added cost.INTRODUCTIONThe acquisition of the Browne Shaft leases in January 1962 presented the management of Broken Hill South Limited with the problem of transporting ore from these leases to its mill. It was eventually decided that diesel locomotivehaulage through a 2t mile drive on the 1,480 ft level between the two mines was the best solution. The drive was advanced from both ends after Browne Shaft was deepened by 80 ft to reach the 1,480 ft level horizon. Each end advancedabout 15 ft/day with the miners working three 7 hr shifts. Blasting was restricted to the end of the shift.The survey work involved five shaft plumbings and 78 theodolite stations in a traverse, underground and surface,of more than 5 miles. Because of the exceptional length of the drive, an unusually high degree of reliability was required.The aim was for a maximum error at breakthrough of 1 ft 1 in 30,000, and to secure this, precise methods of linear measurement were necessary. Shaft plumbing in particular posed special difficulties.

Jan 1, 1965