Search Documents

The French research institute, INERIS, requested the assistance of the CSIR?s Division of Mining Technology in developing further precautionary measures against explosions in their collieries. In response to this approach, an on-board active suppression system was adapted to meet their mining requirements. This system is used on tunnelling machines in Germany where the machine is positioned in the middle of the tunnel, which is therefore not much wider than the machine itself. With this configuration, the machine is never away from the tunnel face during the cutting cycle. As a result, the possible volume in front of the machine of combustible gas requiring suppression is less than 50 m3. In South Africa this technology has been adapted to suit a two-cut mining method which entails greater distances from the face and thus much larger volumes of methane mixtures requiring suppression. The particular configuration of the Explo-Stop® system being investigated required the suppression of possible methane ignition volumes of up to 180 m3of a 9% per volume methane/air mixture. The volume is a consequence of the large cross-sectional area of French underground workings and of the two-cut mining method used in France. In order to take the second cut in the coal seam, the machine is pulled back a maximum distance of 4 m, leaving an air pocket in which gas can accumulate. The machine-mounted system is required to effectively suppress any flame ignited by such a large accumulated volume of methane. The results of the protocol tests done at Kloppersbos showed that the system was capable of suppressing all simulated methane ignitions for the prescribed conditions. This was achieved with a temperature increase of less than a 100°C at the operator?s position and without any flame being detected at this position.

Jan 1, 2001

By S. M. Runke

An earlier Bureau of Mines report4/ reviewed and summarized all reports of investigations dealing with the coarse grained pegmatites of the Black Hills of South Dakota to dune 1951. It was proposed, and the hope was expressed in this report, that future progress in the development of the technology of the mining and beneficiation of the pegmatite deposits would be rapid enough to make it possible to issue annual progress reports. Although notable progress has been made in the treatment of pegmatite material, it has not been rapid enough to justify annual reports

Jan 1, 1954

By M. J. Ramos

Without an exclusive definition of administration in business, we could propose to define it as performance by management to adopt or implement established business formulas. Administration could also be defined as a universal process that organizes people, and achieves, through efficiency, common objectives and goals. Humanity developed some form of this process from the beginning of civilization. To imply that something is new in administration might be considered specious or naïve. Moreover, what is new in management? Administration of business is not new to the world. To prove this statement, we need only ask this question: Does the architecture and monumental workmanship of the past civilizations of ancient Egypt, Rome, and the Incas demonstrate management without administration and without definition of objectives? The answer must be a resounding ?NO!? In spite of this acknowledgment and for the purposes of this presentation, I will use the word ?new? in business and hope that the reader will follow my reasoning. The mining industry has unique characteristics in respect to other industries. It is multi-disciplinary, has a single purpose (majority for one metal), has two players (man and nature), and it involves high risks for generating environmental imbalance. Mining exploits non-renewable and finite resources, creates an unstable job market (work hard to have no work) and a speculative economic market with unpredictable prices ? a one-time payment for a finite resource with multiple recycling. On top of all that, the industry still operates within obsolete petroleum-based technology, utilizing practices that were designed two centuries ago. Today, we confront the challenges of the millennium with outmoded practices and management. Ordinarily, several styles of administration are standardized into a FRAGMENTED vertical system of organization. Mining has rigid objectives in production, with profitability as the focus from the beginning to the end. Citing the concept of safety, as an important facet of production is bombastic since, in truth, mining is an experimental industry that consistently reports high numbers of fatal accidents. In mining, we designed a process to work according to our objectives, demanding attention and supervision of all levels of management with a halo of parameters that are not assimilated into the design. We continue to perform a rigid style of management in an industry that is still not responsive to variations of the market ? losses in particular. The existing design process generates loss without capitalization and without response to said loss. This perception is reflected in a mindset that is only too ready to ignore mining liabilities. The reality of the enterprise has created an immense pressure from top to bottom in the hierarchy to do more with less. It is for all of these reasons that I propose to set forth a new essence for administration that encompasses an alternative vision and style in mining: Management by Loss. MANAGEMENT BY LOSS Management by Loss (MBL) is a systematic, integral process organized to quality control operation and the human profitability within the industry. It permits focus on achievable goals by utilizing the best practices (Mining Open-closing). Identification and characterization of loss in the process determine how objectives are defined, controlling the time limits to execute based on constant balance of mass, energy, water, and ?wastes? in each stage of the industry, in order to reach final objectives. The concept of loss can be defined by various criteria. Generally, it is the mass that could not make or arrive at its destination from a designed process or simply, it could not maintain balance. Otherwise, the design of the process describes the final point of the resource. However, those resources could not make their destination because of failure to use the best design, resources and TIME. The loss has typical characteristics such as Identifiable, classifiable, measurable, manageable, controllable, valuables, negotiable, avoidable, reportable, and monitoring. In the traditional scheme, these losses are not registered; they are made exclusions. We are trapped within a system, which was designed to obtain objectives of the industry in a specific timeframe. In the present style of administration, the focus is total - our emphasis in this treatise is in the loss. The current traditional report form contains only the most positive achievement of objectives, only the best of the exercise, humanizing numbers, without touching what we left behind or what we were waiting for to assimilate as a ?surprise account?(new account of liabilities). Management by loss is a method that redefines the concept of waste (waste zero) for controlling the mine operation under the equilibrium of the ecosystems. This method confronts the problems that impact our industry in this millennium. Understanding and quantifying losses (reserves, resources, time, energy, water, soil, materials, equipment, tasks, labor, ecosystems, etc) is a priority mandate for the industry and demands the application of a ?new ? style of administration by seeking to maintain balance instead of the disequilibrium that mining now creates in nature. It is necessary to answer questions such as: How can we minimize loss? How can the loss be assimilated during the life of the mine? What is the vision of mining in respect to the generation of waste? How can we convert liabilities into assets? In addition, the control of loss is determined in the achievement of the plan. Loss occurs because of a failure of the process in the original plan. Still we do not plan to fail but we fail to plan appropriately. It is a remarkable thing to accomplish and compel those objectives described in the original plan when that plan is designed with a determined budget. If not, we lose time and, of course, capital. Moreover, in Management by Loss (MBL), we can find answers to the following questions: What is the multiplier of productivity in mining? What are the influences of identification and characterization of loss and what is the level of efficiency of energy in order to achieve waste zero (effective cut off grade)? The challenges of mining in this millennium validate this new style of administration. Finally, it is important to point out that mining is entering into an era that has different rules, but the industry is still run by companies functioning with objectives from two centuries ago. They are trying to confront issues with concepts that are not designed for new tasks. Therefore, I ask you to consider this new style of administration of business under a vision of how the industry should be organized and managed, with an attitude of balance toward nature and social responsibility.

Jan 1, 2009

By Mike Boissonneault

It was three years ago when the “storm of the century” had taken a firm grip over the Pacific West Coast and inland areas. At the Big Sky ski resort in Montana on Christmas morning two ski patrollers set out to perform an explosives “hand charge” avalanche control mission that would see only one return. It has been difficult to determine exactly what happened. Investigators do know that there were three separate and consecutive attempts to light a safety fuse, when it had apparently been burning since the first attempt. Time ran out after the third attempt. Although this accident has had a profound impact on North American avalanche control programs, I am sure it pales in contrast to the shock and grief experienced by family members who lost a loved one.

Jan 1, 2001

By A. McLean, M. Iwase, K. Wakimoto, K. Katogi, Y. Kikuchi

One of the greatest obstacles to the application of physical chemistry principles to the elucidation of slag-metal reactions is a lack of knowledge of activities of the reacting species. To a large extent, oxygen potential of the slag phase governs iron and steelmaking practice. Without oxygen control by means of appropriate sensors, the behaviour of the other elements cannot be managed. In this paper, measurements of the FeO activity with various types of electrochemical FeO sensors will be described together with examples of their applications for improved strategies toward better practice for ladle metallurgy and sulphur and manganese distributions between slag and metal phases during steelmaking. Measurements of FeO activity have also been made in order to improve dephosphorization reactions. This type of work has led to significant reduction in volume of slag generated within the steelmaking vessel, which in turn has important implications for refractory wear, metal yield, alloy recovery and improved productivity. Finally, an on-line sensor is described that permits the oxygen potential to be determined for both the metal phase and the slag phase during steelmaking in the BOF.

Jan 1, 2004

By W. I. van Drunick

AngloGold Ashanti Metallurgy has recently been involved in the successful installation of intelligent, expert control systems on the milling circuits. The benefits of expert systems in these highly interactive circuits are obvious. Existing comminution tools, which have been developed and can now be incorporated into online control, include improved modelling techniques and understanding, robust and competent simulation methods, sampling techniques, and optimization methods. The minerals processing industry has seen the benefits of predominantly research-based centres turning their focus to commercial applications of comminution circuit modelling packages, which in turn can be utilized within expert control systems. Expert mill control has been successfully installed at AngloGold Ashanti South Africa?s Mponeng and Kopanang Gold Plants. Expert control has also been installed at AngloGold Ashanti?s West African Sadiola Mine operation. The implementation of the systems has produced a number of positive outcomes. Plant surveys usually result in the identification of sub-optimal areas, and the control philosophy is then configured to ensure that these areas (along with the entire circuit) are optimized and maintained. Outdated PID loops have generally resulted in oscillatory control with large amplitude deviations from set-point. Significant improvements in SAR Metallurgy operations have been realized, firstly through achieving stability in the load and cyclone control, and secondly through online identification and implementation of optimized set-point conditions for mill mass, discharge density, etc. Soft sensors are configured to accurately estimate parameters that were historically not measurable, viz. breakage rate, mill load condition, onlinekWh/t-75 microns, mill discharge density and cyclone overflow grading. The Mponeng Plant system achieved circuit stability and improved overall grind. The Plant was able to pay back the control installation after 3 months, based on the additional recovery obtained from the finer grind. The system at Kopanang Plant has also resulted in enhanced plant recovery as a result of a finer grind and a lower residue gold content. The payback for this system was calculated at approximately 6 months. AngloGold Ashanti Metallurgy is currently expanding the installation of expert control to its other operations. It is also evaluating the performance of various suppliers of advanced control systems.

Jan 1, 2005

By A S. Derrington

There are several long-standing rules of thumb that are often quoted in mine ventilation studies. They include airway ‘carrying velocities’ and the critical upcast air velocity range that must be avoided to prevent a water blanket forming. Quoting these rules of thumb may lend an air of legitimacy to a ventilation design, and allow the design engineer to avoid having to study a problem from first principles. But how valid are these shortcuts in today’s rapidly changing world? This paper summarises research into the genesis of several commonly quoted rules of thumb. It finds that they were very specific to the local conditions, practices and economics at the time they were developed. It also presents examples where applying these rules of thumb outside of their original context can lead to unexpected and erroneous results.CITATION:Derrington, A S, 2017. Ventilation rules of thumb – friend or foe? Focusing on design upcast air velocities for shafts and raise bores, in Proceedings Australian Mine Vent Conference 2017, pp 253–260 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By P. C. Schutte

Ergonomics is the scientific discipline concerned with the understanding of interactions among humans and other elements of a system, and the profession that applies theory, principles, data and methods to design in order to optimize human well-being and overall system performance. Despite the fact that the application of ergonomics principles can make a major contribution to the management of significant occupational safety and health risks, ergonomics is currently applied on a limited scale in the South African mining industry. The objective of this paper is to provide a perspective of ergonomics, the main aim being to create a point of departure for the development of strategic objectives to enhance existing health and safety initiatives through the application of sound ergonomics principles. Two of the major consequences of poor ergonomics, namely work-related musculoskeletal disorders and worker fatigue, and possible means of introducing ergonomics into the South African mining industry, are discussed.

Jan 1, 2005

By Z. A. Md-Nor

Risk management is an established loss-control methodology that has been applied successfully in many industries. Recently, interest in this structured approach has grown in the mining industry. The main objective of this research was to develop a risk-assessment process, which is a part of risk management, that can be used by the U.S. mining industry to more thoroughly characterize risks associated with haul truck-related fatalities. The assessment is based on historical data obtained from the U.S. Mine Safety and Health Administration (MSHA) investigation reports, which includes 113 fatal incidents that occurred from 1995 through 2006. The risk-assessment process used in this research involves the following basic steps: identification of the risks, risk analysis and risk evaluation. The preliminary hazard assessment (PHA) method is used in identifying and quantifying risks. Risk levels are then developed using a pre-established risk matrix that ranks them according to probability and severity. The resulting assigned risk value can then be used to prioritize control strategies. This paper is a part of a detailed study on risk assessment for equipment-related fatalities in mining sponsored by the Western U.S. Mining Safety and Health Training and Translation Center.

Jan 1, 2008

By B. J. Kloppers, J. V. Z. Visser, C. J. Horn

"The long-term plan (LTP) in a mineral resource company is defined by the quality of the mineral resource and represents the result of a series of trade-offs to fulfil internal organizational as well as external business and legislative requirements, ensuring ultimate delivery on the defined organizational strategy.The LTP should as a whole align to a coherent and well-defined organizational strategy, working towards a clearly defined objective while still allowing a tactical response to short-term requirements of the organization. The ability to respond tactically to changes in environment, like the unprecedented five-month strike in 2014 on the platinum belt following the 2012 Marikana incident, is a measure of the flexibility of the plan given the agreed strategy.This paper describes the Lonmin process of linking company strategy with long-term planning, tactical planning, and the execution of the plan through an annual planning cycle to maximize organizational flexibility. This flexibility enables mining companies to respond to the many internal and external forces that impact on both strategy formulation and delivery of results that meet shareholder expectations."

Jan 1, 2015

By F T. Suorineni, L Baird, A Papaioanou, D Hines

The Mathews et al (1981) stability graph was developed to provide guidance in the determination of stope sizes to control dilution in bulk mining of large orebodies. Longhole and sublevel open stoping (LHOS and SLOS) are the lower end in scale of underground mass mining with panel and block caving (PBC) at the higher end. Currently, the stability states of stopes in the stability graph are described qualitatively as stable, unstable or cave. The alternative quantitative option to the qualitative stability graph is the Equivalent Linear Overbreak Slough (ELOS) stability graph. The ELOS stability graph only applies to narrow vein orebodies. It is easy for the Mathews et al (1981) and the ELOS stability graphs to be applied outside the limits of their databases. What is currently referred to as ‘stable’ in the present stability graphs has diverse interpretations at different mines depending on their acceptable dilution values. In 2014, a research program was conceptually conceived at the UNSW Australia School of Mining Engineering to develop a quantitative dilution-based stability graph independent of orebody width to address some industry concerns on the use of the stability graphs. A dilution-based stability graph provides the mining engineer the flexibility to determine open stope sizes based on what dilution amounts are acceptable. The graph also unifies both the Mathews et al (1981) and ELOS stability graphs for wide and narrow vein orebodies, thus, eliminating their potential misapplications. To date, the concept is proven with case studies from metalliferous underground mining operations located across Australia. This paper presents the dilution-based stability graph concept, the initial results and future plans to account for other critical factors and increase confidence in its application with the addition of more data outside Australia.CITATION:Suorineni, F T, Papaioanou, A, Baird, L and Hines, D, 2016. A dilution-based stability graph for open stope design, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 511–522 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Berk. A. A.

"INTRODUCTION Corrosion of sections of piping used in steam-heating systems is frequently regarded as unavoidable, and periodic replacement is provided. Surfaces exposed to newly condensed steam appear to be especially vulnerable to attack. As an added nuisance, solid products of the corrosion tend to accumulate, plugging return lines.The trouble is ascribed in the main to carbon dioxide and oxygen 3/ 4 / 5/ 6/ dissolved in the condensate. When oxygen is the principal factor, the corrosion usually is characterized by pitting. Carbon dioxide tend3 to cause an acidic condensate which dissolves the metal more uniformly and produces the familiar failure at threaded areas where the piping is relatively thin, and where high stress may tend to acceletate the attack. Carbon dioxide enters the system with the feedwater, generally in a combined form such as carbonates and bicarbonates. Oxygen enters both with the raw feedwater-and as air leaking into lines under partial vacuum. The larger central-heating plants have sought to reduce corrosion by eliminating these gases as much as possible. A smaller plant ordinarily lacks the equipment and technical supervision required for this purpose."

Jun 1, 1944

Over the past few years, there has been an emerging relationship between business and civil society, especially NGOs. This relationship has the potential to bring about significant change, identifying common ground between commercial and societal interests. The mining industry has been a leader in acknowledging the need for community consultation and engagement. This paper argues that partnerships can make a very significant contribution to the industry as it comes to terms with the dilemma of an open economic system pushing against a closed ecological system.The paper will pose a number of questions: where is the locus for debate about sustainability in the mining sector?; how well embedded within companies are the new competencies that Leon Davis first identified in 1995 for the mining sector?; how has education for mining engineers or exploration geologists changed to prepare people for what are very different expectations within the working environment?; how well is the industry doing in managing its own environmental impact and what is its responsibility to an agenda for sustainability which extends beyond its own operations?;and how can NGO partnerships contribute to more sustainable outcomes? The paper does not aim to answer these questions, but to explore them in the hope that the issues and possibilities raised will contribute to advancing progress towards sustainability within the industry.

Jan 1, 2002

By Linli Wu

During the measurement of contact angle, a misty band was observed near the substrate. Hsien-Nan Ho and Shinn-Tyan Wu thought this was because the oxygen atoms on the interface migrate to the droplet surface to form an oxide band near the substrate. But from our experiments misty band appeared before the drop reach to the substrate. Theoretically speaking, the oxygen partial was the same everywhere in the vacuum furnace. So there was no condition to provide enough oxygen forming oxide. This appearance would be explained more reasonably with the optics principle. Most reflected light would be absorbed by the substrate and the light cannot reach the observation area, so the misty band formed.

Jan 1, 2006

By Murad Y. Abu-Farsakh

This paper presents the analyses of load-transfer (t-z) behavior of twelve prestressed concrete (PSC) instrumented test piles that were driven in different locations of Louisiana. The load transfer method is an efficient and practical tool for the analysis of single driven pile to predict the ultimate load. The test piles were instrumented with vibrating wire strain gauges in order to calculate the shear transfer for different soil layers during the static load test. The static load test was performed on all the test piles after 10 to 14 days of end of driving. Empirical load-transfer models were proposed previously by different researchers (Fleming 1992, Hirayama 1990, Krasinski 2012, Bohn et al. 2017) after analyzing the instrumented test pile results. For this study, load transfer of each soil layer was measured and compared with the previously developed existing model. The stiffness parameter (M) for the hyperbolic equation was calibrated in order to best match the measurements. The good agreement of the proposed curves was then confirmed by applying them to assess the overall load-settlement curve of other pile load test results available in the literature. INTRODUCTION The load transfer mechanism (stress-strain relationship) for an axially loaded pile usually comprises of three loading mechanisms: axial deformation in the pile (z), soil skin friction along the shaft (qs), and soil end-bearing (qb). The development of soil skin friction with axial deformation is referred as the t-z curve, and the development of soil end-bearing with axial deformation is referred as the q-z curve. Figure 1 presents the load transfer mechanisms in an axially loaded pile and the corresponding spring mass models for t-z and q-z curves (API, 2002). In order to construct the load transfer curve in clay under vertical load, the axial load transfer (t-z) curve and end-bearing load transfer (q-z) for that particular soil should be assessed separately. The axial load transfer (t-z) method is probably the most widely used technique to study the problem of single axially loaded piles. Therefore, the load transfer through the shaft of the pile and are getting more and more important compared to the only the pile capacity analyses. The load transferred from shaft to the surrounding clay soil is a function of the width of the pile and the surface roughness of the pile and clay properties. The development of a representative procedure allows the assessment of the t-z curve in soil (sand and/or clay) that leads to the prediction of a nonlinear vertical load-settlement response at the pile head.

Jan 1, 2018

By M. Nduna

Surface properties of metal sulphides have a great significance in various areas of engineering and science, such as acid mine drainage, contaminant sorption, and metal separation. In various attempts at producing metal sulphide particles from synthetic solutions, prodigious quantities of nuclei that grow only to colloidal dimensions have been frequently reported. This copious nucleation is promoted by the high levels of supersaturation that characterize most precipitation reactions. Colloidal particle formation in precipi¬tation-based separation processes results in sub-optimal solid-liquid separation, which is alleviated by the production of more highly crystalline particles or agglomerates. The current work approaches this challenge from an electrochemistry perspective, by measuring surface charge potential of precipitant particles during metal sulphide precipitation with respect to the concentration of metal sulphide lattice ions in solution. Electrophoresis was used to measure the metal sulphide particle zeta potential and the settling properties were obtained by performing settleability measurements using an Imhoff settling cone. A suspension of copper sulphide particles was precipitated from synthetic solutions of copper and sulphide ions at equimolar concentrations. Immediately after precipitation the copper sulphide particles had a zeta potential of -50 mV and a settleability of about 7 ml.l-1. With the addition of copper ions the settleability increased by a factor of nearly three times and the zeta potential also increased to a maximum of -40 mV. A decrease in zeta potential to a minimum of -60 mV was observed after the addition of sulphide ions and this was associated with a settleability of 0 ml.l-1.

Jan 1, 2013

By Mark P. Meyer

This U.S. Bureau of Mines publication presents salient information in abstract form on 247 coal deposits in Alaska. Coverage includes currently producing deposits and deposits that appear to have commercial production potential. Data arc taken from coal properties identified by the U.S. Bureau of Mines minerals availability program and by a literature search. Infrastructural and institutional factors affecting coal development in Alaska are also discussed.

Jan 1, 1987

By Jackson R. Pressley, M L. Hopkins, R E. Danell, N T. Moxon, Andrew Bowman

Efficient and cost effective blasting is achieved by closely matching the explosive energy to the strength of the material in which it is being used. Although there are many empirical relationships wich approximate this situation complete the blast optimization can only be achieved by quantitatively assessing explosive/rock interactions and explosive performance. The performance of an explosive is essentially governed by its velocity of detonation or the rate at which the detonation wave travels through the explosive column.

Jan 1, 1991

By J. G. Davis

The St. Peter Sandstone is typically a well-sorted, friable, ultra-pure, fine- to medium-grained, quartzose sandstone with silica content higher than 99 weight percent in places. The sand grains are well-rounded, highly spherical and characteristically frosted. Their size typically varies from 2 millimeters diameter (No. 10 U.S. Standard Sieve Series size) to less than 0.08 millimeters diameter (No. 200 U.S. Standard Sieve Series size). A freshly exposed surface of the formation is commonly white with shades of pink and green. Weathered surfaces are a dirty gray or brown and are case-hardened at many localities. Bedding is characteristically indistinct, and the formation usually appears massive throughout. The rock is cross-bedded and ripple-marked locally. The formation is generally porous, permeable and rarely fossiliferous in Missouri. The St. Peter is continuously present in the subsurface in the northern half of the state and along the southeastern edge of the state. The St. Peter crops out in a narrow band that starts in western Montgomery County and runs southeastward, along the Missouri River, to just west of St. Louis and continues south, just west of the Mississippi River, through Scott County. The outcrop belt varies from less than one mile wide to over ten miles wide, and it is over 150 miles in length. The formation dips into the subsurface radially away from the outcrop band. A notable isolated outcrop occurs in Lincoln County to the north of the main outcrop band. The St. Peter is discontinuously present in the subsurface along a band in the west-central portion of the state. It is not present at the surface or in subsurface in the remainder of the state. The formation averages 80?100 feet thick. There is an estimated 3.8 trillion short tons of St. Peter in Missouri. Sieve analyses on drill cuttings indicate three subsurface locations in northeastern Missouri where the St. Peter is greater than 10 percent by weight of sand falling in the 20?40 U.S. Standard Sieve Series size range. The St. Peter was first produced in Missouri in the 1870s for the manufacture of glass. Since that time it has been used as a paint additive, filler material, polishing compound, filtering media, and recently it is commonly used as a fracture proppant in oil and gas wells. The St. Peter is currently quarried and produced in Missouri from four sites located in St. Louis, Jefferson and Perry counties. In the same area there are at least nine abandoned historic mine sites.

Feb 27, 2013

By C. K. Man

Coal dust explosions in underground coal mines are prevented by generous application of rock dust (usually limestone). If an explosion should occur, the rock dust disperses, mixes with the coal dust and prevents flame propagation by acting as a thermal inhibitor or heat sink. To investigate this process in more detail, a number of explosion experiments using various coal dust and limestone rock dust mixes have been carried out at the Lake Lynn Experimental Mine (LLEM). These were conducted in a single entry of about 1600 ft (488m) in length and initiated with a methane gas explosion. A consistent set of post-explosion floor dust samples were taken along the entry after each test. These dust samples have been analyzed in the laboratory using thermogravimetric analysis (TGA) and solubility to determine how the limestone rock dust behaved during the coal dust / rock dust explosions. The preliminary results are reported in this paper and indicate that the chemistry of limestone plays an important role in its capacity to inhibit coal dust explosions. The results also show that it may be possible to estimate the intensity of the explosion using these conventional methods of analysis. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009