Search Documents

By A. M. Cummings

Each mining district presents different problems as to the methods of ore extraction cad underground support, which are dependent upon the type of the ore deposit and the character of the inclosing rock. Mining costs, however, depend largely aeon the efficiency with which the methods employed underground are [applie] as well as upon the selection of the method best adapted to the physical conditions. The purpose of this paper is to present to the operator in other districts a detailed description of ho mining method used ins results obtained in tie exploitation of the bedded magnetite deposits of the Mineville district. The town of Mineville is situated in the Adirondacks, five miles west of Port Henry on Lake Champlain.

Jan 1, 1928

By B. W. Gandrud

In July 1948, the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and mine operators, published Report of Investigations 4306, "A Combination Cleaning and Dewatering Process for Treating Fine 'Sizes of Coal, Preliminary Report In this report a new process, referred to as kerosene flotation; was described, and results of experimental work with the process Previous to the fall of 1947 were given, The contents of the report. were summarized on pages 19 and 20' as follows: In coal-preparation plants using wet methods of cleaning, the most difficult problem is the cleaning and dewatering of the "fines" from about 10-Mesh to 0. A combination proceed is now under investigation that shows promise of practically and feasibly solving this problem. The process is similar to froth flotation, but a generous quantity of kerosene is used as one of the reagents, and the feed is from approximately 10-mesh to 0 considerably coarser than the usual froth flotation feed. The kerosene and the coarseness of the reed result in a floated product that, under certain circumstances, can be dewatered satisfactorily by a simple process of mechanical squeezing, Squeezing is accomplished by means of an ordinary conveying' Auger-and trough assembly with a section of pipe easing at the outer end of the trough. The bottom of the trough and. casing is fitted with wedge-wire sections to permit escape of the water freed by the squeezing action of the auger. On account of the important role of the kerosene, the process has been referred to in this report as kerosene flotation. Up to now, the investigative work has been divided about evenly between the laboratory and commercial plants. Nearly all of the work has been done on sludges containing the solids from the underflow of dewatering screens. A few runs have been made on 10-mesh to 0: fines from raw coal, but in some of those runs the dewatering mechanism, failed to function.

Jan 1, 1950

By S. Ersayin

In 1998, the Concentrator Modeling Center was established within the Coleraine Minerals Research Lab to develop models for simulation of iron ore processing plants, and to assist plant operators in improving performance of their aging plants. The short-term objective was to develop necessary models for reliable simulation using conventional techniques, while the long-term objective was set as liberation-based modeling and simulation of these plants. The short-term objective was achieved in 2002, after the development of models for magnetic separators, hydroseparators and fine screens. A project funded the US Department of Energy was carried out to demonstrate the capability in improving iron ore processing at the Mittal plant. As a result of this study, a 10% improvement in throughput at the plant was obtained, and simulation became a desired tool for plant operators. A significant step in the long-term objective was reached in 2005 with the development of a liberation model. This was followed by incorporation of models capable of processing liberation data into the software. By early 2007, the Center had the capability of performing liberation-based simulation of entire plants.

Jan 1, 2008

By William W. Adams

Accidents to men employed in the quarrying and related industries of the United States were more numerous, absolutely and relatively, in 1937 than in 1936. Fortunately, the entire increase was in the category of nonfatal injuries, as accidents causing death declined in number and in proportion to the number of man-hours worked. Employment increased. More men were employed, more man-days and man-hours were worked, and the average employee had more hours of work than in 1936. Reports covering all commercial operations showed that 84,094 men were employed an increase of 5.1 percent over 1936. The number of man-hours of work performed by the industry was, 158 millions, an increase of 7.6 percent. Seventy-seven men were killed by accidents, a, reduction of 14 from the year before, and 6,348 men were injured and disabled for more than the remainder of the day on which the accident occurred, 11 percent more than in 1936. The fatality rate of 0.49 per million man-hours of exposure in 1937 compared favorably with the rate of 0.62 for the previous year, whereas the non-fatal-injury rate of 40.10 was 3.2 percent higher than the rate of 38.87 for 1936.

Jan 1, 1940

By R. B. Crookston

Oil shales differ from coals in that they contain less carbonaceous material, convertible to volatile hydrocarbons, and more inorganic rock. In all pre-commercial oil shale development, involving extensive full scale mining operations, there have been no explosions. However, large scale mine tests with oil shale dusts by the Bureau of fines showed that propagating explosions could be induced under certain circumstances. Laboratory tests were conducted on a broad spectrum of oil shale dusts to define chemical properties and to seek correlations with subsequently determined fire and explosivity properties. These latter properties, indicative of safety hazards, increased as the Fischer assay oil yield of the dusts increased and as particle size decreased. Laboratory data were used to relate fire and explosivity properties of oil shales to those of coals and other carbonaceous materials and to assist in the identification and evaluation of potential hazardous situations which may be encountered in oil shale mining and processing.

Jan 1, 1978

By F. T. Cawood

Inauguration of the new political dispensation in South Africa in1994 initiated a dynamic shift in the ownership, management and development of the country?s affluent mineral heritage. The process of substituting the old South African regime with a new equitable system started soon after the 1994 election of the African National Congress (ANC) to parliament. The Congress?s Freedom Charter revealed the intent of the new dispensation when it called for radical transformation of mineral development. However, since then there have been important changes affecting the rules of mineral development. These are: ?A drastic change in politics ushered in by negotiation, a spirit of reconciliation and a desire to settle disputes peacefully ?The globalization of the South African mining industry in tandem with the opening of domestic mineral resources to foreign capitalists and ?The introduction of sustainable development as a holistic approach to mineral development in order to replace traditional narrow-minded environmental management. Each of these significantly shaped the new mineral investment environment of South Africa. This paper represents a summary of the historical developments leading to the current Mineral and Petroleum Resources Development Act No. 28 of 2002, its regulations, the much publicised Broad-Based Socio-Economic Empowerment Charter, its associated Scorecard, and the Draft Royalty Bill.

Jan 1, 2004

By R. Larry Grayson

In the October 1998 issue of the Holmes Safety Association Bulletin, NIOSH authors Mark Stephenson and Carol Merry wrote the article Hearing loss among miners and measures to protect hearing, which focused on the extensiveness of hearing loss among miners and the use of hearing protection to prevent hearing loss. While the primary importance of engineering controls in preventing hearing loss was discussed, since miners do not generally have control over their work en­vironment or assignments, the article focused on the importance of consis­tent use of hearing protection. In this article, all aspects of a compre­hensive approach to the prevention of hearing loss in miners will be covered. The discussions will do the following: ? describe application of the hierarchy of controls in preventing hear­ing loss in miners, ? give an example for each type of control measure and its impact, ? explain the major provisions, be­yond the hierarchy of controls, of the recent NIOSH document en-titled Criteria for a Recommended Standard: Occupa­tional Noise Exposure, Revised Criteria 1998 relative to a hearing loss prevention program, and ? summarize important points on control of noise exposure for every miner to remember, equipment in most facets of operations. Miners are well aware of noisy areas in or around equipment, icluding extraction machinery such as draglines, power shovels, longwall shearers, and continuous mining machines; powered haulage equipment such as load-haul-dumps, shuttle cars, large trucks, and continuous haulage units; roof bolting machines; jackleg drills and stopers; auxiliary equipment such as compressors, fans, and pumps; size reduction equipment, etc. They are not well aware of the insidious nature of pro­gressive hearing loss, which is per­manent, but they are generally aware of what levels of noise are hazardous and what measures can be taken to reduce their personal noise exposure. Behaviorally, however, there are many reasons why miners choose not to use hearing protection faithfully.

Jan 1, 1998

By A Buckley

Many policy issues facing the mining industry and affected communities are at a level of complexity that they can be called ‘wicked’ problems. The term ‘wicked’ in this context is used, not in the sense of iniquity, but rather as social and economic issues highly resistant to resolution. For the resource extraction sector and affected communities there are an array of challenges embedded in the industry’s production and profit paradigm, the remoteness of mineral reserves and affected communities’ expectations of economic benefit and a positive legacy. The mining industry as a whole is dominated by economic, political, legislative and market structures that influence and constrain interactions between mine operations and local communities. For communities, with particular reference to regional Western Australia, intractable problems include the uncertainty of, yet increasing dependence on, a mining economy. Questionable outcomes for local communities include the limited realisation of local employment and business development benefits, and low overall outcomes or low multiplier effects. ‘Wicked’ problems, according to the literature, are best addressed via collaboration. In the mid-west region of WA, with mining and infrastructure construction underway, alliances have formed between mining companies, the major port and rail infrastructure project (Oakajee Port and Rail) and regional and local governance stakeholders. The major impetus for these affiliations is to expedite planning and associated infrastructure development taking into account the lessons from other mineral-led regions. What has resulted is an array of innovative approaches to stubborn problems including planning well in advance of full-scale mining; regionally coordinated procurement; ‘mine ready’ local businesses; and strategic investments in social infrastructure; including community trust funds paid in advance of project delivery. This paper examines these innovative approaches/alliances and assesses their effectiveness in addressing long standing mining/community dilemmas.

Nov 22, 2011

By H. C. Liang

Reverse osmosis (RO) and nanofiltration (NF) are widely regarded as being best available technologies (BATs) for removing contaminants of concern from water. In recent years, NF or RO treatment has increasingly gained more acceptance in the mining industry for treating mine water to remove a wide assortment of contaminants, either for meeting discharge standards or for internal re-use in mining processes. Consequently, the number of NF or RO membrane mine water treatment facilities has steadily increased. Although NF or RO membrane filtration can be a powerful tool in mine water treatment, especially when multiple contaminant removal is required, it also has many potential disadvantages. Besides the generally higher capital and operational costs for the high pressure membrane processes, organic constituents in mine water may foul the membranes, while inorganic compounds such as gypsum, calcite, or silica are liable to scale the expensive membranes if proper pre-treatment processes are not implemented. Additionally, because these membrane treatment processes generate a substantial reject or brine waste stream in addition to the clean treated water or permeate stream, brine management also needs to be considered carefully when deciding upon the viability of an NF or RO mine water treatment process. Because of these issues, it is important to conduct detailed analyses of the trade-off between selecting NF or RO vs. using chemical treatment processes when designing a mine water treatment facility.

Jan 1, 2012

By B. Ceki, A. Mabentsela

The BCL furnace is scheduled to restart operations after being placed on care and maintenance in 2016 due to depressed nickel prices. The decision to start operations after such a stoppage ought to be led by a techno-economic evaluation of process options to make operations more resilient. For BCL, the decision lies between using the existing flash-smelting furnace (FSF) or a top-submerged lance (TSL) furnace. Available studies show that the FSF combined with other converting technologies is cheaper to operate; however, such studies are based on flowsheet simulation results of single copper concentrates and therefore do not provide a full scope of practical capabilities based on smelter operator skills. Using a t-test on normalized prior operational data from three Cu FSF and two Cu TSL, it was found that the only statistical differences between the operating costs of the FSF and TSL technologies are in the coal use for heating the feed blow and number of rebuilds: the FSF consumes coal to heat the feed blow and the TSL requires 2.4 rebuilds during a course of a single FSF campaign. A summative operating cost comparison over the existing BCL FSF 11-year life shows that BCL can decrease operational costs by some BWP 55.5 million if the operation were to change to the newer TSL technology. The savings derive from reduced coal use, which is normally associated with heating the blow when using the FSF. Despite the TSL carrying added costs of 2.4 rebuilds during a life time of one FSF furnace campaign, the cost associated with the TSL rebuilds of approximately BWP 1.3 million is minimal compared with the overall operational expenditure decrease that BCL will incur on using the TSL technology. In terms of the technology, BCL can have higher Ni–Cu recoveries at lower operational costs by elimination of Ni–Cu losses and eliminating the slag-cleaning furnace by converting to a TSL furnace.

Jul 10, 2024

By William Gleason

The numbers tell the story of this one. More than 50,000 people and 1,890 exhibitors took over the Las Vegas Convention Center Sept. 24-26 for the largest mining trade show in the world ? MINExpo. Inside the convention center, some of the largest machines used in mining were on display. Caterpillar, Liebherr, Komatsu and Hitachi displayed ultraclass offroad mining trucks and shovels. Atlas Copco and Schramm were among companies that rolled in mining drills and Bridgestone, Goodyear and Michelin were among the companies showing off the massive tires used by the trucks. Throughout the three halls and an outdoor display area, just about every kind of product, gadget or service used in the mining industry could be found on display somewhere.

Jan 1, 2012

By L. Cifuentes, J. M. Casas

The treatment of aqueous CuSO4-H2SO4- As-Sb solutions by electrodialysis in order to separate and concentrate species of interest has recently been studied. Results show that it is possible to separate copper from arsenic in electrodialysis cells. The separation of copper from antimony is also possible. Transport rate ranges that could be achieved, depending on experimental conditions, are 0.2 to 0.6 mol per hour per square metre of membrane for copper, 0.65 to 2.8 for sulphate, and 0.016 to 0.03 for arsenic. Transport rates for antimony were inconclusive due to its very low solubility in the studied systems. Solution agitation and increasing temperature markedly increased the process rates. Advancements in this area require further work in both the thermodynamics (speciation) and kinetics of complex CuSO4- H2SO4-H2O systems, where impurities, other than As and Sb, and additives should be taken into account to gain a deeper understanding of the application of ED to copper electrorefining electrolytes

Jan 1, 2004

By R. H. Sprute

The Federal Bureau of Mines conducted full-scale field tests in electro-kinetic dewatering and consolidation of slimes in cooperation with the Hecla Mining Co. at two of the firm's underground mines in north Idaho. To test the technique on new deposits, 4,000 ft3 of slimes from a collection sump, pumped into a watertight stope equipped with electrodes, were treated in two steps. Immediately after placement, direct current was applied using a floating electrode to hasten settlement of suspended fine particles. After removal of clarified water, the residue was further dewatered and hardened with electrokinetic treatment. In 25 hours, the material had become firm and dense with a surface capable of supporting workmen. In testing old deposits, 10,000 ft3 of slimes, placed in an unused tail drift 10 to 12 months previously, were treated. This material was sufficiently consolidated by electrokinetics to allow its removal from the mine with standard ore-handling equipment. In both tests, electrokinetic treatment densified slimes in a relatively short time with moderate power consumption.

Jan 1, 1976

According to the previous research, it is found that the thickness of cover is mostly less than 100 m for highwall mining system. However, for most of the Chinese surface coal mines, the mining depth is over 150 m; on the other hand, the shovel-truck is the most common mining technology. As a result, a lot of residual coal will be remained around end-walls. Considering these facts, the calculated methodology of highwall mining system under thick cover is presented in this paper. Meanwhile, numerical simulation of highwall mining system under thick cover was carried out. The outcome shows that the calculated methodology for pillar stability of highwall mining system under thick cover presented in this paper is acceptable. In other words, the highwall mining system is feasible to extract the residual coal around end-walls in Chinese surface coal mines. Thus, not only coal recovery ratio can be improved, but also can increase the production life of surface coal mines in China.

Jan 1, 2012

"This generic study has been developed in response to the frequently asked question, ""That is the best treatment route for refractory gold ore?"". The study has developed operating and capital costs for many potential treatment routes and they are presented here in a generic form. All costs are in relation to the value of 1.00 given to the base case, a 1000 mtpd bio-oxidation plant, operating at 25% solids and 72 hours residence time.There is unfortunately no simple answer to the above quest ions. The treatment of refractory ores is a complex subject, with many variables, such as mineralogy, chemistry, environment and tonnage. However this study does offer information and relative numbers that we believe will be of assistance to gold metallurgists in obtaining a ""first shot"" at estimating costs.Equally, this technology is a rapidly evolving one. As more plants are commissioned, and test programs completed, better data is constantly being generated. For a generic study of this type to remain useful it will need regular updating and adjustment."

Jan 1, 1989

Since March 28, domestic producer prices on 99.5 percent aluminum ingot have been at 5l¢ per pound. Dealers in this same time frame have held ingot quotes at 49¢-50.5¢ per pound. COBALT: Imports from southern Africa in 1976 constituted 73 percent of total cobalt imports. Moreover, the United States is 98 percent dependent on imports of cobalt. For this reason, the Bureau of Mines is closely monitoring developments abroad to ensure an advance notice of any possibility of a shortfall in supply. Included in these imports were those from Zaire (41 percent directly from Zaire and 15 percent via Belgium-Luxembourg), Zambia (11 percent), and Botswana (6 percent). Also being closely watched are industry stocks.

Jan 1, 1977

By J. A. Finch, Zhenghe Xu, Z. A. Zhou

A particle-bubble collision model was used to investigate the minimum recovery zone height, H(r,min) required for flotation columns. The criterion used to define H(r,min) is that height which gives unit collision probability. It is shown that H(r,min) is determined by particle and bubble size, gas hold-up and bubble-bubble interaction. Under typical operating conditions, for flotation of particles less that 10 micrometres in size H(r,min) is greater than 10 m, but it reduces to less than 1 m for particles greater than 100 micrometres

Aug 1, 1995

By P G. Rutherford, A W. McOnie

A volcanic sequence is described from the Golden Cross Mine, Waihi, New Zealand. The sequence includes seven lithostratigraphic units comprising flow and pyroclastic units of Coromandel Group andesite and dacite and overlying Whitianga Group dacite and rhyolite which is intruded by the Golden Cross dacite porphyry and rhyolite dykes. The sequence is mineralised and is unconformably overlain by two post-mineral units, the lacustrine Waitekauri beds and Omahine Subgroup andesite.   Detailed structural analysis of mine data has identified four deformational events (D 1-D4) and related these to the gold-silver mineralising events. Faulting was coeval with the mineralization and directly controlled the development, localisation, style and geometry of the ore shoots. Mineralization developed in competent lithologies where dilation occurred during faulting. The Empire Fault is the master shear which controlled fluid flow. Mineralised veining developed in response to tectonic pulses occurring at slightly different stages as represented by the underground Empire vein complex and the open pit vein array. The mineralising events culminated with the deposition of barren calcite veins. Post-mineral movement along the Western Boundary fault appears to have offset the orebody.

Jan 1, 1995

Although cyclones have been around in their current form since the early-1890s, there have been some exciting new developments, which have extended their efficiency/operation. These developments have taken place with both dense medium and classification cyclones. The more noteworthy developments are:Inlet designInlet design is the determining factor in classification cyclone capacity and efficiency. The recently developed ribbon inlet with patented pressure bulge has not only resulted in unbelievable increases in capacity, but also in efficiency. Sharpness of separation corresponding to an alpha value of greater than four has been achieved! Secondary offtakeOne of the factors leading to reduced cyclone efficiency is the presence of coarse particles in the cyclone overflow. The secondary offtake has been developed specifically to scavenge these particles from the cyclone overflow with great success. Water injectorThe other major factor resulting in reduced cyclone efficiency is the presence of misplaced fine particles in the cyclone underflow. The water injector, which has been around for many years in various forms, can reduce this short circuit fraction by up to 50 per cent. 3-in-1 cycloneThe 3-in-1 cyclone combines the inlet design, secondary off take and water injector into a single unit resulting in the most efficient classification cyclone available in the market. The RejectorTMIron ore has a high yield to underflow and traditional dense medium cyclones have always been spigot constrained. The Rejector TM is an exciting new development whereby the spigot capacity has been increased substantially. The application of the Rejector TM will result in fewer/smaller cyclones being required for a given duty resulting in efficiency gains and reductions in both operating and maintenance costs.

Jan 1, 2002

By J. D. Davis

THE carbonizing properties of one medium- and and five low-volatile coals from West Virginia and one high-volatile A and two medium-volatile coals from Pennsylvania were determined by 800° and 900° C. BM-AGA carbonization tests and expansion tests in the sole-heated oven. Plastic properties of the coals and the yields and quality of their cokes and other carbonization products were determined. The low-volatile coals comprised a mine and a coke-plant sample of Pocahontas No. 6-bed coal from the. Black Eagle No. 1 mine, Wyoming County, W. Va.; a mine sample of Pocahontas No. 6 bed from the Louisville mine, Mercer County, W. Va. ; Davy Sewell bed was sampled at the Twin Branch mine, McDowell County, W. Va.; and Fire Creek bed was sampled at the Dunedin No. 1 mine, Raleigh County, W. Va. The medium-volatile coals were from the Fire Creek bed, Laurel Creek mine, Greenbrier County, W. Va.; Lower Kittanning bed, Springfield No. 4 mine, Cambria County, Pa.; and Upper Kittanning bed, Springfield No. 6 mine, Clearfield County, Pa. The high-volatile A coal represented the Upper and Lower Freeport beds, Kent Nos. 1 and 2 mines, Indiana County, Pa. In addition to the coals listed, high-volatile A coal from the Pittsburgh bed, Warden mine, Allegheny County, Pa., a standard blending coal, was used in blends in this investigation.

Jan 1, 1950