Search Documents

By Sergio Neves Monteiro

The efficiency by which an applied load is transmitted through the composite structure depends on the strength of the interface between the matrix and the second phase. In fiber reinforced composites, the interfacial shear stress plays a major role in the composite capacity to support the applied load. This interfacial stress can be obtained by means of pullout tests using the fiber embedded to a certain length in a socket of the matrix material. In the present work, pullout tests were performed to evaluate the interfacial shear stress of ramie, a relatively strong natural fiber, reinforcing polyester matrix composites. The general result permitted to calculate a critical length for the ramie fiber embedded in polyester resin. From this critical length, the value of the interfacial shear stress was calculated. An interpretation of this result together with SEM observation displayed a relatively weak bond between the ramie fiber and the polyester matrix.

Jan 1, 2010

By M. A. Barakat

"Adsorption of heavy metal ions specifically, Cu(II), Zn(II), Mn(II), and Cr(VI) from aqueous solution on synthetic 4A Zeolite was evaluated. The 4A zeolite was synthesized previously by dehydroxylation of low grade Kalabsha Kaolin at 800 °C, and reacted hydrothermally with 2-4 M NaOH solution at 100 °C for 2h. The adsorption capacity of the metal ions were found to be strongly dependent on pH and initial metal ion concentration. At the optimium conditions the adsorption capacity decreased in the order Cu(II) > Zn(II) > Mn(II) > Cr(VI) ions. Almost complete adsorption was achieved for both of Cu(II) and Zn(II) ions at pH > 6, while the adsorption capacity for both Mn(II) and Cr(VI) was 96, and 55.3 % at pH 11 and pH 3, respectively. The results also showed that the grain size of the 4A zeolite has a little effect on the adsorption capacity. The experimental data was compared with two adsorption isotherms, Langmuir and Freundlich isotheroms. The results showed a good agreement of the Langmuir plots with the experimental data.1. IntroductionSeveral industrial wastewater streams may contain heavy metals such as Cr, Cu, Pb, Zn, Co, Ni, Mn, etc. including the waste liquids generated by metal finishing or the mineral processing industries. Heavy metals are considered hazardous pollutants due to their toxicity, even at low concentration, and nonbiodegradability. Increasing level of heavy metals in natural water bodies poses a serious threat to all living species including humans. It is, therefore, essential to reduce the heavy metal concentration in effluents/wastewater before it is discharged into the water bodies [1]."

Jan 1, 2008

By Tian Sugui

By means of the measurement of the enduring property and microstructure observation, an investigation has been made into the influences of the element Re and TCP phase on the enduring property of the single crystal nickel base superalloys. Results show that the needle-like TCP phase is precipitated along the <110> orientation on {111} planes in Re-containing/free superalloys during the long term aging, the TCP phase is identified as µ phase, and the precipitated µ phase in 4.5%Re alloy is gradually spheroidized during aging. Thereinto, the needle-like µ phase may obviously decrease the enduring lifetimes of the alloys due to the consumption of the refractory elements and the effect of the stress concentration. But the stress concentration is not easily generated in the regions near the spherical-like µ phase, which is a main reason of reducing the enduring lifetime of 4.5%Re alloy to a small extent.

Jan 1, 2010

By C. Coetzee

Additives are commonly used in copper electrowinning to improve cathode morphology. Polysaccharides such as guar are generally favoured as additives due to their compatibility with solvent extraction. Polyacrylamides are, however, being considered as possible alternatives. Understanding the influence of the structural chemistry of additives on electrowinning performance is critical to utilise them efficiently. This paper investigated polyacrylamide additives which are structurally different; their effects on copper electrodeposition were characterized and compared to that of guar. Electrochemical impedance spectroscopy (EIS) were used to characterize the effects of molecular weight and ionic charge of the polyacrylamides on electrodeposition. The findings were compared against results obtained with an industrially used guar product. Equivalent circuit modelling of EIS data indicated that an increase in polyacrylamide concentration and a decrease in additive molecular weight increased the overall system resistance.

By Zhouhua Jinag

The attempt has been made to manufacture high nitrogen austenitic stainless steels by pressurized electro-slag remelting furnace with maximum nitrogen pressure of 7MPa. To obtain high nitrogen content in steels, the compound electrodes with different nitrogen sources (FeCrN, Si3N4) were prepared. Using the Si3N4 as the nitrogen alloying source, the silicon contents in ingots were prone to be out of the specification range, and the electric current fluctuated greatly and the surface qualities of the ingots were poor. The surface qualities of the ingots were improved using FeCrN as nitrogen alloying source. The sound and compact macrostructure ingot with the maximum nitrogen above 1.0wt% could be obtained. A series of high nitrogen austenitic stainless steels have been successfully developed by this method. The mechanical and pitting corrosion resistance properties of high nitrogen austenitic stainless steels were investigated. The results show that the steels exhibit excellent mechanical and pitting corrosion resistance properties.

Jan 1, 2009

By Pengfu Tan

One copper Isasmelt furnace has been operated in Xstrata Copper at Mount Isa in Australia since 1992. A thermodynamic model and computer program, CuModel, has been developed to model the distribution behaviors of Cu, Fe, S, O, Ni, Co, Sn, Pb, Zn, As, Sb, Bi, Au and Ag, copper loss in the slag, and heat balance in copper smelting process, matte converting process and copper continuous smelting process. The thermodynamic model has been used to model the key parameters in the control of the copper Isasmelt furnace. The effects of the process parameters on the control of the copper Isasmelt furnace have been predicted and discussed. These process parameters include SiO2/Fe, matte grade, coal, temperature, spec air of feed, oxygen enrichment, and MgO contents in slag.

Jan 1, 2006

By Pietro Navarra

A great deal of effort has been expended on how to optimize conventional water cooling circuits in furnace cooling elements, and the results have been largely satisfactory. However, there is a general agreement that the proximity of high-pressure water passages to the flow of molten furnace products is a safety concern. Nonetheless there exists little alternative to the formula: increasing furnace integrity implies the incorporation of more extensive forced-convection water cooling systems. Recent developments in evaporative cooling technology have resulted in the development of a high-capacity heat pipe capable of operating under the thermally intense environments of a metallurgical furnace. The system functions using several kg of a working fluid (water) in total, has no moving parts, and allows for a significant reduction in cooling water requirements. Full-scale pilot tests of a copper tap hole and slag launder were done in 2003 and2005, with detailed results given in this paper.

Jan 1, 2006

By Yue-yuan Li

China has abundant magnesite resource, but the low-grade and powder ores have always been rejected, which influences the comprehensive utilization of resource and often causes circumstance problems. The present work investigated the preparation of magnesia whisker using magnesite tailings as starting materials by preparation magnesium carbonate whisker as precursor firstly in the route of calcination, hydration, carbonation and pyrolysis, follows by second calcination of the precursor. The influence of pyrolysis conditions and additives on morphology of magnesium carbonate crystal as well as the influence of calcination conditions on morphology of magnesia whisker was investigated. The results showed that thermal decomposition products was MgCO3?3H2O. Magnesium carbonate whisker with length of 10~60 µm and the length-to-diameter ratio of 10~20 was prepared when soluble magnesium salt was added. While temperature was elevated at 1°C?min-1, magnesia whisker with length of 10~60µm was obtained.

Jan 1, 2010

By Wellington Pereira Inácio

This work investigated the toughness behavior of polyester matrix composites reinforced with up to 30% in volume of long, continuous and aligned sisal fibers by means of Charpy impact tests. It was found that the addition of sisal fibers results in a marked increase in the absorbed impact energy of the composites. Macroscopic observation of the post-impact specimens and SEM fracture analysis showed that longitudinal rupture through the sisal fiber interface with the polyester matrix is the main mechanism for the remarkable toughness of these composites.

Jan 1, 2010

By P. J. Mackey, J. B. See, D. G. C. Robertson

The production of iron and steel and non-ferrous metals by pyrometallurgical processes will remain a critical element in meeting the demand for materials in both developed and developing nations. Given the important need to reduce and minimise greenhouse gas emissions the technological focus of future pyrometallurgical R&D by universities and industry alike must concentrate on sustainability issues such as improved energy efficiency, recycling and waste minimization. Continued efforts are also needed on process optimization and new process development with a view to reducing capital and operating costs of the new large “mega” plants. Using the academic and industrial backgrounds of the authors, the present paper reviews the current status of R&D in pyrometallurgy in university departments with a particular emphasis on sustainability issues. The role of industry and government laboratories is also reviewed although primarily for developed countries. The paper also includes comments and suggestions on the future requirements for education and R&D in pyrometallurgy in developed countries to maximise sustainability. It is also suggested that future R&D in pyrometallurgy will be even more concentrated in developing countries – most notably China.

Jan 1, 2014

By M. Potesser

One of the main targets in the automotive mass industry and supplying industry is the weight reduction of the vehicle for decrease of the fuel consumption. For that reason combinations of different kinds of materials and connections of, for example, steel and aluminium are developed or are already successfully field-tested. A determining factor concerning the quality assessment of the welded joint during hybrid welding is the characterization of the intermetallic Fe-Al layer regarding strength, hardness, morphology and mainly the different phases in which Fe occurs together with the Aluminum (FeAl, Fe2Al5, FeAl3.). A combination of conventional light microscopy, SEM - EDX - analysis, the usage of an atomic force microscope including a Nanoindenter and theoretical thermodynamic calculations turned out to be highly effective. Based on the attained results, the constitution of the intermetallic FeAl layer, influenced by silicon, manganese and zinc, can be predicted.

Jan 1, 2006

By M. T. Baquera

A comparison of microstructures associated with W single-crystal ([001], [011], [111]) rods prior to deformation (as grown), and after quasi-static compression (at a strain rate of ~1/s) by transmission electron microscopy (TEM) shows several orders of magnitude difference in dislocation density. Dislocation substructures were not significantly different amongst the deformed sample orientations. In contrast, [001] W rods penetrated into steel targets, at impact velocities of ~1.3 km/s, exhibited heavy dislocation densities and dynamic recrystallization as very distinct microstructural regimes accommodating the penetration process. Twinning on {112} also occurred as a precursor to, or remnant of, these microstructures near the projectile head. These results suggest that deformation accommodating the extreme strains and strain rates associated with the penetration of a single-crystal rod into a metal target is not adequately represented by conventional deformation

Jan 1, 2006

By Geysen. Daneel

Better slag valorization is part of improving the sustainability of steel, stainless steel and non- ferrous metal production processes. Besides, it can improve the sustainability of other products and production processes as well. A sound and well established slag valorization is beneficial for the overall economics, marketing and appreciation of the metallurgical process and its products. On 6-7 April 2009, the First International Slag Valorisation Symposium was held in Leuven, Belgium. This paper gives a brief summary of the symposium, providing an overview of slag valorization opportunities. The authors believe that high temperature process slags can have interesting applications and that within the next 10 to 20 years slags will need such valorization options in order to compete with other materials and get general support for further production. On the other hand, the authors also expect a higher demand for slags for the production of various materials. High temperature processes should anticipate on the growing opportunities for valorization of slags and increase the resilience of their process by better understanding slag processing, slag quality and material requirements. More interdisciplinary research efforts are required to reach this level of knowledge for the different high temperature processes. Such an interdisciplinary research platform was recently established at KULeuven, Belgium, named SMART-PRO2 (Sustainable Materialization of Residues from Thermal Processes into Products).

Jan 1, 2010

By Paul W. Cleary

Keywords: Reactive pellets, CFD, Lagrangian SPH, Pyrometallurgy In several pyrometallurgical processes, reactive pellets are added to a melt. Heat is transferred to the pellets and reaction products such as gases, metal and slag are formed. For many pyrometallurgical processes traditional grid based CFD methods, such as using the Finite Element Method (FEM) and Finite Volume (or Control Volume methods), produce suitable predictions. However, the inclusion of solids in the bath represents significant challenges for these methods. Smoothed Particle Hydrodynamics (SPH), a Lagrangian simulation method, is able to simulate both the fluid component of the bath and any immersed solid materials, tracking the motion of these solids, and their interaction with the fluid, including gas generation. In this paper, we will summarize the key aspects of the SPH method and will show a series of structured examples illustrating the behavior of the different physics sub-systems that are used in the model of the overall system.

Jan 1, 2005

By Mishark Nnabuchi

A heterojunction of PbS - CuS thin film has been grown on glass slides by SGT. The films were annealed for 1hr at temperature of 373K and 423K respectively. The optical properties were characterized using a UNICO UV - 2102 PC Spectrophotometer at normal incidence of light in the wavelength range of 200 - 1000nm. The minimum percentage transmittance was observed to be 34% for sample A and 25% for sample B within the same optical region. The band gap energy was determined from the spectra to be 2.05eV for sample A and 1.85eV for sample B which gave a band shift of 0.20eV. It can thus be concluded that the optical properties of the films within the VIS - UV - NIR can find application in solar thermal technology, particularly as antireflection coating, window materials and as good materials for selective solar cell fabrication.

Jan 1, 2010

By P. M. Swash

The paper describes the use of mineralogical methods in the exploration and evaluation of primary diamond occurrences. The most common methods that are used include the systematic search for kimberlitic indicator minerals, surface textural study of the indicator minerals, (garnet, spinel, ilmenite and chrome diopside) and alluvial macrodiamond studies so as to understand their provenance and guide exploration towards diamondiferous targets. The mineral chemistry of the indicator is used to positively assess the origin of the mineral grains and is also pivotal in the determination of the diamond potential of a deposit. Petrography of the primary deposit is able to identify the body to be kimberlitic and is also a support to the mineral chemistry findings. Unambiguous proof of a prospects potential to contain macrodiamond is proven by the occurrence of microdiamonds in the residues from the rock. The presence of a sufficient number of microdiamonds in the rock is enough to determine a semiquantitative grade estimate and warrant further metallurgical evaluation so as to determine its actual macrodiamond content.

Jan 1, 1991

By P. A. Mahanwar

Flyash were melt mixed with nylon 6 at a 30wt% concentration. TYZOR® TPT, a coupling agent, was used to facilitate the link between filler and matrix. The morphological characterization, using SEM, revealed sufficient matrix residue on the filler surfaces thus confirming the strong interfacial bonding between the filler and the matrix on treating. Tensile, impact and the flexural properties of the composites were also improved with the incorporation of coupling agent. As flyash particles tend to impart a grayish color to the plastic, TiO2 pigment was employed to make the formulations aesthetic. The pigment was added to the filled system in 0.1, 0.5, 1.0, 1.5, 2.0 wt/wt ratios. Scattering of incident light and spectral reflectance was higher for smaller particle size flyash. Moreover an increase in the scattering with increase in pigment concentration indicates better dispersion of the pigment, which again is due to the presence of coupling agent.

Jan 1, 2006

By H. Antrekowitsch

Nowadays, the pyrometallurgical treatment in copper smelters is the common process for the recycling of metals from the electronic scrap. Furthermore the European Directive on the Waste from Electrical and Electronic Equipment (WEEE) and the Directive on the Restriction of Hazardous Substances (RoHS), increase the importance of electronic scrap recycling. Besides these a high amount of plastic and inert components in these materials leads to problems at the processing. An optimisation concerning the internal recovery and the high amount of plastic is necessary to reach the recycling quota of the European directive. The majority of the scrap is treated mechanically in order to separate in a first step plastics from metals, iron from nonferrous metals and harmful substances from valuable materials. But the quality of the different fraction often rather low and further treatment leads to higher costs. Therefore an interaction between mechanical treatment and metallurgical processing should be realised. The Christian Doppler Laboratory for Secondary Metallurgy of Nonferrous Metals at the Institute of Nonferrous Metallurgy at the University of Leoben carried out investigations concerning the optimisation of the metallurgical recycling and the treatment of the input materials especially of printed circuit boards.

Jan 1, 2006

By T. R. A. Davey

The technologies of lead, zinc and tin extraction have made varying degrees of progress over the past twenty years. Producers of all metals have faced increasing demands for reduction of pollution and environmental degradation, and the level of public concern is rising rather than abating. New processing techniques must therefore be not only economically feasible, but politically acceptable, even when the demands of "conservationists" and ?environmentalists? are unreasonable. A new generation of processing techniques has come into being, which do not rely on an expensive sintering stage, nor use metallurgical coke, which is difficult to make without serious pollution. They utilise intense reactors, conveying materials from one stage to the next preferably within an enclosed space, obviating fume emissions, and avoiding heat losses as far as possible. The acceptability of the new techniques? is increased if lowgrade or complex materials can be treated, along with a variety of returns and wastes. In addition, a good selling and servicing organisation seems to be as important as good process technology in determining the spread of the new processes. In the field of pyrometallurgical refining the need is for more general application of several recently developed techniques rather than a search for alternatives to the existing process technologies. However, there is a need for fundamental work investigating the phenomenon of oxygen anode overvoltage in the electrolytic zinc process, in order to make progress in the further reduction of energy consumption. There is also scope for further development and application of vacuum distillation to up-grade thermally produced zinc. This paper presents a personal view of processes which should be developed to overcome existing problems, as we approach the turn of the century,

Jan 1, 1990

By Jacques J. Eksteen

Any effort to improve the metallurgical control of industrial furnaces employed in the primary extraction of high carbon ferroalloys are bound to fail unless the variability of the melt is not fully accounted for. A number of sampling campaigns were performed on both 3phase AC submerged arc and single phase DC open arc furnaces at different smelter sites in South Africa where High Carbon Ferrochrome is produced. It was found that the heterogeneity between multiple samples during a single taps were much higher that for heterogeneity found within a sample. Moreover, this heterogeneity (as quantified by the relative standard deviation per tap) varied with the operating conditions of the furnace, the element monitored and the type of furnace. A relationship was found between the relative standard deviation of certain elements and the degree of subcooling of the melt.

Jan 1, 2006