Search Documents

By Varadarajan Seshadri

A physical model based on similarity principles was constructed for simulating the RH degasser of CST (Companhia Siderurgica Tubarao, Vitoria, ES, Brazil) to evaluate the circulation rate of the metal which essentially defines the degree of exposure of the metal to vacuum in the chamber and thus of the refining rate, The circulation rate on the other hand will influence the decarburization rate and removal of dissolved gases like nitrogen and hence it is essential to optimise this parameter to get maximum refining efficiency with minimum refining times, thus improving the productivity of the secondary refining process. Mixing characteristics in the ladle is evaluated by pulse tracer addition using conductivity-meters located at the down leg as well as at several locations in the ladle. The influence of gas injection through nozzles in the upleg with simultaneous bottom injection of gas as well as nozzle blockage on the circulation rates were investigated. Also simulation experiments of kinetics of decarburization were carried out using CO2 adsorption-desorption process in sodium hydroxide solution as circulating fluid and the effect of, bottom gas flow rate in this case was also evaluated. The results were carried over to prototype and to optimize the process.

Jan 1, 2003

By Ernt. W. D.

A membrane based mixed extractant process was developed for selective removal of copper from waste acidic cupric chloride etchant solutions found in printed wire board manufacturing. The process uses a mixture of Adogen 381 (tri-isooctylamine), MOC®-45 (ketoxime) and MOC® 55TD (aldoxime) in a kerosene diluent. The mixed extractants recover the copper from a hydrochloric acid medium and transfers it to a sulfuric acid medium. The process also utilizes unique wetted membranes to separate the aqueous and organic phases. The driving force for these membranes is not pressure but the difference in surface tension between the two phases. By using these membranes, complete phase separation results. There is no physical entrainment contamination as found in conventional systems. The only cross contamination is the solubility concentration of one phase in the other. This however is less than 10 mg/l.

Jan 1, 1998

By Karl A. Gschneidner

The magnetocaloric effect has been known for 120 years and has been utilized for cooling about 70 years. But in the last four years significant advances have been made to show that magnetic refrigeration is a viable and competitive cooling technology. Most of the work has focused on reciprocating devices, but rotary apparati are being developed. To date the magnetocaloric properties have been characterized for more than 200 materials. The magnetocaloric effect behaviors have been classified into three types of behaviors. The most common one is found in magnetic materials which exhibit a second order magnetic phase transition. Magnetic materials which exhibit a first order magnetic phase transition account for the second group of materials. Materials which exhibit multi-magnetic phase transitions make up the third group. The best candidate materials for magnetic cooling over the range from -4 to -1 350 K are also presented.

Jan 1, 2002

By Jim A. King

The total pressure oxidation of copper concentrates is a potentially viable option for treating copper concentrates that are either low grade or contain significant impurities. Both concentrate types are heavily penalized in smelter contracts. The total pressure oxidation process involves autoclaving the copper concentrate at temperatures of 200-220 C under oxygen pressure. The autoclave discharge can be separated into a solid (oxidation residue) and a liquid (oxidation solution) product. The oxidation solution can be treated for copper recovery by solvent extraction - electrowinning or by direct electrowinning. The direct electrowinning recovery of copper requires prior removal of selenium and tellurium by cementation on finely divided scrap copper. The oxidation residue is washed thoroughly to remove acid and dissolved copper prior to precious metals recovery by conventional cyanidation in the presence of lime. The results of a benchscale investigation involving a number of copper concentrates are reported. Copper recoveries in autoclave oxidation and gold recoveries by cyanidation of the oxidation residue exceeded 99%. The results of benchscale experiments to demonstrate copper recovery are described. Various flowsheet options are presented.

Jan 1, 1993

By Larry Hopkins

The molten metal circulation pump has become a staple for melting aluminum in reverberatory furnaces. The forced convection that is created in the melt efficiently provides circulation while dramatically improving melt rates, lowering fuel consumption, extending refractory life, and providing metallurgical homogeneity. Two metallurgical guidelines that are important to many casthouses are molten metal inclusion levels and hydrogen gas content. In order to improve molten metal quality, furnace and casting practices must 'manage these molten metal defects, Today specialized in-line degassing and filtration equipment is used downstream of the furnace to accomplish these tasks. In contrast, the molten metal gas injection pump has metallurgical contact time in the process for hours during the charging/homogenization cycle. The qualitative benefits of employing a gas injection pump to "pre-clean" are outlined and discussed against historical empirical information obtained with alternate methods. Further, a recent study quantifies the merits of this gas injection technique as an effective molten metal quality improvement tool. Specifically, the effects on inclusion level as determined by PoDFA?, gas content as determined by A1SCAN? sampling and alkali metal content as determined by spectrographic analysis are examined in relationship to various gas feed compositions and flow rates.

Jan 1, 1995

By James E. Hoffmann

Oxidative pressure leaching is gradually supplanting other techniques for the decopperizing of slimes. The reasons for this include: much more rapid reactions, more compact equipment, a reduced environmental burden, and perhaps most important, a much lower final copper concentration in the decopperized slimes. This paper will discuss the reactions occurring during decopperization, the acidity and temperatures encountered and the techniques employed for discharging non condensable gasses. A spreadsheet is provided which allows adjusting the operating conditions depending upon raw (undecopperized) slimes composition, solids concentration and lixiviant composition. A typical process equipment flowsheet is provided along with a process narrative.

Jan 1, 2000

By J. R. Sarazin

Density driven convection during solidification has been recognized for some time to result in macrosegregation particularly when lower density alloying elements are rejected into the interdendritic liquid. The resulting segregates are commonly referred to as channels, freckles or A-segregates. Buoyancy driven convection leading to channel formation has been examined in three model systems possessing somewhat different materials parameters. They are the Pb-Sn eutectic system, the transparent aqueous-salt NH C1-H 0 4 2 eutectic system and the transparent organic succinonitrile-ethanol monotectic system. Convection in these systems is controlled by a balance of buoyant and viscous forces, which are strong functions of composition and temperature. Composition, temperature and flow velocity were measured and elimination of channels through heavier ternary additions is discussed.

Jan 1, 1991

By Jafar Safarian, Merete Tangstad, Leiv Kolbeinsen

"Silicon and its binary alloys have several applications in metallurgical, chemical, photovoltaic and semiconductor industries. Silicon goes to its liquid state within its production, refining and when it is alloyed with other elements. Therefore, the characterization of silicon melts thermodynamics is important and useful. The liquidus and activities in several silicon binary systems have been recently calculated by the application of two liquidus constants, which were established using the experimentally determined liquidus data. In the present study, the thermodynamic properties of six silicon binary melts, which are simple eutectics, are calculated by analytical approaches. In this case, the changes in the partial and integral Gibbs free energies and enthalpies of mixing are calculated and compared with the experimental data in literature. The enthalpies are calculated by two methods and the calculation results are compared to the data from the literature. It is shown that thermodynamic properties of silicon binary melts can be accurately predicted without the use of complicated thermodynamic software.IntroductionSilicon and its alloys have several industrial applications. Silicon is used for making aluminium-silicon alloys to produce cast parts, mainly for automotive industry. Silicon in the form of ferro-silicon is used to deoxidize and alloy steel and cast iron. The photovoltaic (PV) industry has had a rapid growth in the recent years and silicon is the dominant material used for the fabrication of solar cells. Silicon is primarily produced through carbothermic reduction of quartz in electric arc furnaces and the produced metallurgical grade silicon (MG-Si) contains around 1 wt% impurities. It is further refined to produce solar grade silicon (SoG-Si) with above 99.9999 wt% Si to fulfil the chemical requirement for PV application. Since molten silicon is processed all along the metallurgical route, obtaining fundamental thermodynamics knowledge about silicon melts is valuable for the related industries."

Jan 1, 2012

By R. J. St. Eloi

The Kidd Creek Copper Smelter has been expanded from its original design of 59,000 tonnes of copper per year to over 120,000 tonnes per year .. Modifications to the process gas handling system and acid plant have been made to accommodate this higher production rate and to .generally optimize the operation. The gas handling system associated with the continuous smelting process is discussed in terms of boiler accretions and modifications to minimize their impact on operations; design changes to effect reductions in high pressure drop duct configurations; material changes to overcome corrosion and plant additions to 'improve gas cleaning capability. The acid plant is reviewed with references to changes made to accommodate the increased S02 gas strength resulting from the higher smelting rates;

Jan 1, 1992

By Mike Johnson, Niels Verbaan, David Dreisinger

The Search Minerals Foxtrot project in Labrador is a surface deposit enriched in the highly sought after heavy rare earth elements. Early metallurgical work investigated beneficiation of the rare earth content of the Foxtrot resource using flotation, gravity separation and magnetic separation. The concentrate was then processed by acid baking and water leaching to produce a REE leachate for purification and recovery. The Search Minerals Direct Extraction Process was developed through bypassing the beneficiation process and directly acid treating a coarse crushed ore material prior to water leaching. The result is a simple, low risk technical process for direct recovery. Concurrently, the treatment of the water leach solution was modified to produce a high grade (98.9% total rare earth oxide) product for refining.

Jan 1, 2016

By Takaaki Shibata

The Tamano Refinery has developed two new processes for removing the impurities, arsenic, antimony, and bismuth from an electrolyte. The first process involves bleeding the surface electrolyte in the electro-refining cells. The copper concentration level in the outermost layer is lower than that in any of the other layers, while the impurity levels are almost the same in all layers. Bleeding the surface electrolyte increases the amount of impurities removed in the liberator by approximately 20%. The second process involves adsorbing antimony and bismuth from the electrolyte by means of chelating resin. As the electrolyte passes through the packed column of chelating resin, antimony and bismuth are selectively adsorbed. They are then desorbed by means of hydrochloric acid, and then recovered in the form of a highly concentrated antimony chloride solution by means of evaporation. This process almost doubles the capacity for removing antimony from an electrolyte.

Jan 1, 1987

By R. P. King

The essential features of an image analysis system for the measurement of mineral liberation are described. Good procedures for image acquisition and image processing prior to image analysis are defined. The basic stereological methods for the measurement of volume fraction, surface area per unit volume, particle size distribution and liberation spectra are given. The appropriate methods for fractal correction when measuring perimeters of irregular features and for frame correction when measuring linear intercepts are developed. Practically useful and accurate procedures for the stereological correction of particle size and liberation distribution methods are given.

Jan 1, 1995

By Steven R. Izatt

IBC Advanced Technologies, Inc. (IBC) has developed a mercury selective product, which can be used by sulfuric acid producers as either a polisher, or as the primary technology for mercury removal from sulfuric acid. The Molecular Recognition Technology (MRT) separations material selectively binds Hg2+, and to a lesser extent Hg+, out of concentrated sulfuric acid. Mercury output levels of less than 0.1 ppm can be attained by the MRT system. Pilot plant tests have been successfully conducted at base metal smelting operations. A large-scale commercial plant is due for commissioning in 2003. Results from these projects will be discussed.

Jan 1, 2003

By Donna Guillen, Matthew Lehar, Sebastian Freund, Jennifer Jackson, Helge Klockow

"Research and development is currently underway to design an Organic Rankine Cycle (ORC) system with the evaporator placed directly in the hot exhaust stream produced by a gas turbine (GT). ORCs can be used to generate electricity from heat that would otherwise be wasted, thus producing carbon-free energy. In conventional ORC configurations, an intermediate oil loop is used to separate the hot gas from the flammable working fluid. The goal of this research effort is to improve cycle efficiency and cost by eliminating the pumps, heat exchangers and all other added cost and complexity of the additional heat transfer loop by developing an evaporator that resides in the waste heat stream. Direct evaporation – although simpler and less expensive to implement than indirect evaporation of the working fluid – has historically been avoided due to a number of technical challenges imposed by the limitations of the working fluid. The high temperature of the hot exhaust gas may cause decomposition of the organic working fluid and safety is a major concern due to the high flammability of some of these working fluids. The research team has addressed these challenges and developed a new direct evaporator design that can reduce the ORC system cost by up to 15%, enabling the rapid adoption of ORCs for waste heat recovery. The ORC system is intended to integrate with the GT either as a retrofit or to be marketed as a single package, thus maintaining the manufacturer’s warranty.IntroductionWaste heat from turbines and engines used in industrial applications along with waste heat from industrial processes are exceptionally abundant sources of energy. If even a fraction of this waste heat could be economically converted to useful electricity, it would have a tangible and very positive impact on the economic health, energy consumption, and carbon emissions in the U.S. manufacturing sector. Land-based gas turbines are used in a broad range of applications to produce both shaft and electrical power. Most commonly known for generating electricity either as peaking units or as base load units, they are also used to directly drive pumps, compressors or other machinery requiring shaft power. Simple cycle gas turbines have the advantage of a short startup time relative to coal-fired and nuclear units, however, they incur a significant penalty on their efficiency. Large frame gas turbines usually are combined with bottoming steam-based Rankine cycles to increase the overall efficiency of the system and thereby improve their cost performance. Small-frame gas turbines with exhaust temperatures around 500°C could in principle benefit from steam bottoming cycles, but rarely use them in practice because of the high capital cost of the steam system. Particularly for base load small frame gas turbines, akin to those used in pipeline applications, an increase in efficiency is highly desirable."

Jan 1, 2011

By Sacha Neven

Submerged lance technologies combine high intensity processing characterized by rapid mixing and reaction rates using a simple reactor design. The Isasmelt technology uses a central submerged lance to inject oxygen-enriched air and fuel into a bath thus creating large gas bubbles and intensive turbulence and splash. The lance is equipped with swirlers to increase gas velocity and heat transfer. This enables the formation of a frozen slag layer on the lance which protects it from the aggressive environment. Water models as well as high temperature reactors were used to validate the Davidson-Schiiler model on bubbling. Frequencies and pressure amplitudes were measured in a wide range of gas flow rates: from m3/sec using a water model to more than 30 m3/sec in an industrial process. Agreement with the model was satisfactory. The experiments however also clearly showed that cross-flow and bubble wake induce slightly higher frequencies. No influence of the use of swirlers on the bubbling frequency was observed in the water models.

Jan 1, 2002

By XUEWEN WANG, Bowen Li, Mingyu Wang

A novel technology characterized by higher extraction of vanadium and recovery of valuable elements was developed to recover vanadium from stone coal. The brief flow of the novel technology mainly includes low temperature sulphation roasting, water leaching, recovering potassium, aluminum, copper and selenium, solvent extraction enrichment vanadium, precipitation of red vanadium, removal sodium from red vanadium and calcinations. The total recovery of vanadium reached 76.3%, which was higher than the current applied technology. The novel technology was environmentally-friendly and could extract vanadium from the stone coal, in which the content of V2O5 was less than 0.8%.

Jan 1, 2015

By James C. Barker

Recent investigations of a 55-km long trend of intrusive complexes on southern Prince of Wales Island have identified significant resources of Nb, Y, REE. U, Zr, and a host of potential by-product metals. The northwesterly trend comprises multi-phased sodic alkaline and peralkaline diorite, monzonite, syenite, and riebeckite granite. There are at least three significant deposit types recognized, two of which, 1) pegmatite dikes/vein-dikes that zone laterally from the intrusions and 2) concentrically zoned pegmatites, contain most of the lithophile metals. A third, epigenetic replacement-type mineralization, contains much of the U resource. Other deposit types with minor or unknown resource potential include diatremes, carbonatite, and placers. This report summarizes the deposit evaluations, characterizes the mineralization, and estimates the resources. To date a total of 40.7 million tons of mineralized material is estimated as indicated or inferred. Most of the Y203 plus REO is at a grade exceeding 0.5% and half of the Nb20S exceeds 0.125%. Tonnage estimates would likely be substantially lncreased with additional exploration. Mineralogy is generally fine-grained and complex, and consists of more than a dozen principal REE-Y-Nb-U-Th-Zr phases, the sum of which may compose up to half of the rock. Approximately half of the REE-Y content comprises the heavy yttrium subgroup which is uncommon compared to deposits elsewhere. Although the Alaskan deposits are likely subeconomic at today's metal prices and consumption levels. recent technological advances suggest future demand may increase.

Jan 1, 1988

By Rubén Alvarado

The markets and environmental protection rules are more and more exacting, both of which have determined that copper smelters should look for technological development and global management to ensure their viability and competitivity in the short and long term. The main facilities of the present and future Smelting-Converting Process at Codelco's Caletones Smelter, is based on Teniente Converter reactors with a high operational availability that have reached concentrate processing capacities near 2,000 tpd. These reactors are in operation in most of the smelters in Chile as well as in Zambia, Peru, Mexico and, in ?the near future, in Thailand. Since 1993, the Smelting-Converting process of the Caletones Smelter of Codelco-Chile has been based on one Reverberatory furnace, two Teniente Converters and four Peirce-Smith Converters. These facilities, together with the operation of two Fluidized Bed Dryers, three Slag Cleaning Furnaces, and two Oxygen Plants have allowed the smelter to reach concentrate smelting capacities and copper productions of 1,215 kt/year and 360 kt/year, respectively. This transitional operating scheme, combining together traditional and advanced technological equipment, needs further modernization to successfully face the modern world challenges, especially with relation to the environmental commitment, production costs and wide satisfaction of customers. For this reason, for the period 1997-2000, a Modernization Plan has been worked out. This plan considers an increase of the present throughput, which will permit a significant increase in productivity, as well as finding a definitive solution for meeting the environmental regulations. Among these projects, we can point out the definitive shut down of the Reverberatory Furnace, which is a contaminating piece of equipment of low energetic efficiency. Additionally, it considers the installation of two new Slag Cleaning Furnaces, one additional Oxygen Plant, and the incorporation of two new Sulphuric Acid Plants with a production capacity of 4,500 T/D, that will recover over 92% of the sulphur content, of process off-gases.

Jan 1, 1998

By John H. Schloen

Copper refineries are constantly looking for methods to upgrade their plants to reduce refining costs and to improve the purity of their electrolytic cathodes at the same time that the purity of the anodes they refine is being lowered by the rehabilitation of reverberatory furnace smelters to one of the direct smelting processes. The comments given below are based on the answers to the questionnaire returned bf the 36 copper refineries that represent 66% of the western world s refining capacity. Eleven refineries employ some form of uniform weight anade casting, e.g., Outokumpu, Contilanode, Mitsubishi, Lurgi, or Hazelett. This type of anode casting presents the best possibility for improving cathode purity. The cathode press of Phelps Dadge can improve current efficiencies and cathode quality. The press is used on first-run cathodes, after 48-60 hours, on half-cells at a time without interruption of the cell current. One refinery interrupts current for sever.al hours to allow the anode slime to settle before the, cathode pressing. The cathode press is now used at eight refineries. Apart from periodic reverse current (PRC), it is not expected that current densities will be increased. Thirty refineries, using direct current, average 231 amps/M, with a low of 178 and a high of 350. Five refineries use PRC at an average of 338 amps/M, with a low of 290 and a high of 380. Current efficiencies are good at an average of 94%, with a low of 88% and a high of 99% for the 34 refineries that reported. It must be remembered that the cycle efficiency with PRC is about 93%., so that the effective current efficiency with PRC would be only .94 X .93 or 87% However, PRC should be considered seriously for refinery expansions because it can save about 25% on capital costs.

Jan 1, 1987

By M. M. Kim

Zn-27% Al was pressure infiltrated into a column of 20 micron diameter abrasive grade SiC particles to give billets with particle loading of 50 voli.une %. Some billets were heated to a temperature where they became semi-solid and diluted with liquid Zn-27% Al alloy to give billets with particle loadings of 12 and 16 volume %. Some of these billets were then extruded into wire with an area reduction of approximately 98%. Tensile properties of the as-cast billets were always inferior to those of the matrix alloys; however, the extruded composite samples showed at 37% improvement in ultimate tensile strength compared to their extruded conventional counterparts. The fracture surfaces of these samples are described.

Jan 1, 1990