Search Documents

By D. C. Lynch

While a sizable amount of data exist as to the activity and distribution of minor elements between matte and metal, there has been no unifying theory presented delineating the form of dissolution of these elements in molten sulfides. In order to alleviate that deficiency the literature concerning the behavior of As, Sb, Bi and Pb in mattes is reviewed. Models present in the literature, regarding the thermochemical behavior of minor elements, are tested, and new models are presented and evaluated using thermodynamic theory. The results of those analyses are used to predict optimum conditions for the volatilization of minor elements. The dearth of data on the behavior of minor elements in nickel mattes requires that this review focus on copper- iron mattes. An effort is made, however, to utilize basic knowledge regarding nickel sulfides and the interaction of nickel with the minor elements to predict the behavior of those elements in nickel-copper and nickel-iron mattes.

Jan 1, 1993

By Giulio R. Altoé, Sergio N. Monteiro, Ygor M. Moraes, Rômulo L. Loyola, Frederico M. Margem, Gabriel O. Glória

The tensile properties of DGEBA/TETA epoxy matrix composites reinforced with different amounts of PALF fibers were evaluated. Composites reinforced with up to 30% in volume of long, continuous and aligned PALF fibers were tested in an Instron machine at room temperature. The fracture was analyzed by SEM. This one revealed a weak fiber/matrix interface, which could be responsible for the performance of some properties. The results showed significant changes in the mechanical properties with the amount of PALF fibers.

Jan 1, 2015

At its Copper Cliff Smelter, Inco Limited processes a bulk copper-nickel concentrate in two Inco oxygen flash furnaces, The furnace matte is converted to low iron matte for further processing, and the molten converter slag is recycled to the flash furnaces. The flash furnace slag is discarded. Natural gas or coke supplies a minor proportion of the process heat requirements, thus limiting the flash furnace matte grade to the target 45% CuNiCo. Coke addition to the furnace offers a potential means of establishing a reducing barrier on the surface of the molten bath. Such a practice would be conducive to producing sulfur deficient (partially metallized) matte. At the same iron content, the iron activity of sulfur deficient matte is higher than that of regular matte. A supernatant coke barrier could, therefore, be expected to lead to higher nickel and cobalt recoveries, reduction or even elimination of magnetite furnace bottom build-up and increased sulfur elimination as S02 in the flash furnace. Preliminary experiments were conducted in a miniplant flash furnace to investigate the effect on process metallurgy of the suggested modified scheme. This paper presents the experimental results and discusses key aspects of the possible operation of the Inco flash furnace with a coke barrier separating the freeboard from the molten bath.

Jan 1, 2003

By D. S. Barr

The Freeport McMoRan chlorination circuit is comprised of four related processes: ore chlorination, gas scrubbing, chlorine supply and excess hypochlorite removal ("hypo kill"). Each of these processes are described, and related to the pertinent mineralogic components in the carbonaceous ore feed to the plant. The chlorination system in use at Jerritt Canyon to passivate forms of preg-robbing organic carbon has proven to be a cost effective and efficient means to recover gold from low sulfide carbonaceous refractory ores, where gold may not be specifically associated with either the sulfides or the carbon.

Jan 1, 1987

By Guy Xueyi

The environmental impact assessment of the Imperial Smelting Process for metallic zinc and lead production in Shaoguan Smelter, China, was carried out by the life cycle assessment method. The detailed inventory analysis of the Input/Output in the process during 1998-2000 was conducted and the allocation was done among the main products of zinc, lead and sulfuric acid, according to the system expansion and substitution principle, The environmental impacts were assessed by using the following five Eco-indicators: Gross Energy Requirement (GER), Global Warming Potential (GWP), Acidification Potential (AP), Heavy Metal Toxicity' (HMT) and Solid Waste Burden (SWB). The results from this study are useful to address the environmental situation of the technology practice in this smelter, and provide a scientific basis for the further improvement.

Jan 1, 2003

By A. Bilodeau

A new hydrometallurgical process for the production of refined gold and the recovery of palladium and platinum from silver anode slimes has recently been developed and installed at the, CCR Division of Noranda Inc. The process, which facilitates the production of gold of >99.99% purity in the face of increasing palladium receipts comprises; leaching silver anode slimes with hydrochloric acid and hydrogen peroxide at 95°C to solubilize gold, palladium, platinum and base metals while simultaneously rejecting silver as insoluble silver chloride; precipitating gold from the leach solu¬tion with sulphur dioxide gas in two stages to produce a first-stage high purity gold product and a second stage impure gold which is recycled to the leach; washing, melting and casting of the pure gold; precipitation of a palladium-platinum concentrate from the gold-free solution by reduction with sodium formate at pH 4 and 95°C; and neutralization of the palladium precipitation effluent to pH 10 with lime. The results of laboratory and pilot plant studies leading to the adop¬tion of this process are discussed, and data are presented for each of the unit operations. Details of the engineering of the commercial plant are given, and plant start-up experience is described.

Jan 1, 1987

By Fan Jiang, Haigang Wang, Shi Liu

"This paper describes several applications of Electrical Capacitance Tomography (ECT) in gassolid two phase flows. A new image reconstruction algorithm was evaluated by both simulation and experiments. It is then applied to the online measurement of solids distributions in square circulating fluidized beds (CFBs) and good results were obtained. From the measurement of solids distributions in the bottom zone of a CFB, a bubbly fluidization pattern is identified. A cross-correlation technique was combined with the solids concentration measurements to obtain the flow rate through the dip leg of the cyclone, i.e. the circulating rate of a test CFB. The same· technique was applied in a dense phase pneumatic transport pipe provides the solids concentration, and the flow rate of a wavy gas-solids flow.IntroductionElectrical capacitance tomography (ECT) has been developed for imaging multiphase distributions in the 90's of the ·last century. It is a non-intrusive method. The principle of ECT can be firefly described as follows:Firstly ECT uses a number of electrodes to surround the measuring zone, depicted by Fig. I. The capacitances between the electrodes are measured in turn and an array C is obtained that contains a total number of m independently measured capacitances. Meanwhile the measuring zone is virtually divided into a grid of n pixels, represented by an array G, named the image vector, the gray level of each pixel represents the local value of the concentration of the material. As the material distribution will be reflected by the capacitances between each pair of electrodes, such distributions can be reconstructed according to the measured capacitance, a process called image reconstruction. A common image reconstruction method is called linear-backprojection (LBP). It linearize the relationship between the dielectric distributions in the measuring zone and the capacitances between the electrodes as the following:"

Jan 1, 2004

By Ragnhild E. Aune, Mark William Kennedy, Shahid Akhtar, Jon Arne Bakken

"To determine the heating rate of billets using ‘short coils’, an appropriate correction factor must be applied to the theoretical relationship. In 1945, Vaughan and Williamson published a semi-empirically modified Nagaoka coefficient applicable for moderate frequency induction heating processes (10 kHz). Recently it was demonstrated that the method of Vaughan and Williamson gives <10% error in the estimated power when heating aluminum billets at 50 Hz.In the present study, experiments have been conducted on aluminum billets in order to verify an empirical frequency corrected ‘short coil’ equation. Measurements of electrical conductivity (<± 0.5%), current (± 1%), heat (± 1-3%), and magnetic flux density (± 1-2%) have been performed. The results are compared with 1D analytical calculations, and 2D axial symmetric FEM modeling using COMSOL 4.2®. The frequency corrected equation has proven to provide accurate predictions of power (<4% error) within the frequency range 50 Hz to 500 kHz.IntroductionInduction heating is commonly applied to the re-heating of billets before forging or extrusion processes. The resistive heating produced by eddy currents in the solid or semi-solid work piece during this procedure, is driven by the time varying magnetic flux density in the air-gap between the work piece and the coil. The flux in the air-gap is created by the current flowing in the induction coil, i.e. the magneto-motive force. In Figure 1 it can be seen that the currents present in the work piece are concentrated in the outer ‘shell’, or the first electromagnetic penetration depth (dw), and flow in a direction which opposes the magnetic field produced by the induction coil."

Jan 1, 2012

By J. D. Miller

Gold adsorption from cyanide solutions by activated carbon has been studied at great length during the past decade. Findings from past research are reviewed and discussed with respect to structural features of various carbons, including carbon black, activated carbon, graphite and diamond.

Jan 1, 1991

By Kandipati Sreenivasarao

Ion and precipitate flotation involve adding an appropriate collector to aqueous solutions containing metal ions, to form hydrophobic metal-collector complexes or precipitates that can be removed by flotation. With a better fundamental understanding of the effects of physical, engineering and chemical parameters on the performance, ion and precipitate flotation techniques could usefully complement techniques now available for removing metal ions from dilute solutions. The removal of Cu(II), Pb(II), Cd(II), Cr(III) and Cr(V1) has been studied, using different types of collector, according to the nature of the metal-bearing species. The effects of collector/metal ion ratio, and solution and froth height on the flotation kinetics, bubble coverage by the metal-collector complex, recovery of metal and effluent quality are reported. The observed behavior is related to the solubility products of the metal-collector complexes, which were also determined.

Jan 1, 1994

By Susanne Pignolet-Brandom

QEM*SEM is an automated scanning electron microscope/computer system that characterizes samples with regard to mineral modal abundances, mineral grain and particle sizes, mineral associations, and particle surface areas. Additional information, based on the classification of particles according to the area percentage of a mineral of interest, can be obtained for samples of particulates. QEM*SEM is capable of analyzing a wide variety of materials although it was originally developed for applications to the minerals industry.

Jan 1, 1988

By Frederick T. Wallenberger

"Laser assisted chemical vapor deposition (LCVD) is a new containerless fiber process whereby growth of small diameter fibers or microstructures (microsprings, microsolenoids) occurs directly from the vapor phase. The laser beam has a focal point adjusted to coincide with the tip of the growing fiber inside the reaction chamber. Since the growing fiber is not in contact with reactor walls or foreign materials, it is chemically pure, and suitable for optical uses and uses requiring high structural uniformity. Continuous fibers and multifilament yams are possible. The use -of high reaction chamber pressures (1-10 bar) and a small wavelength Nd-YAG laser made it possible to fabricate small diameter fibers at growth rates >1 mm/s. This paper describes the synthesis of single crystal, polycrystalline and amorphous fibers by LCVD, and provides a comprehensive analysis of phase transformations occurring during their fabrication.IntroductionLaser assisted chemical vapor deposition (LCVD) is a new containerless fiber process [1-10] whereby growth of small diameter fibers or microstructures occurs directly from the vapor phase. The laser beam has a focal point adjusted to coincide with the tip of the growing fiber in the reaction chamber (Figure 1). The diameter of the growing fiber corresponds to that of the laser focus. Depending primarily on the laser energy (Le., the temperature at the growing fiber tip), it is possible to obtain single crystal, poly crystalline or amorphous fibers by this method.Since the growing fiber is not in contact with reactor walls or foreign materials, it is chemically pure, and suitable for optical uses and uses requiring high structural uniformity. Laser assisted CVD is a potentially continuous process; continuous fibers and multifilament yams are possible."

Jan 1, 1994

By H. Dong, J. J. Valencia, L. Nastac

"A comprehensive computer model was developed to understand and optimize the centrifugal casting process for manufacturing TiC/Al-bronze friction drums. Performance of these components requires proper distribution of TiC particles, which is shown by dimensional analysis to be dominated by centrifugal buoyancy effects and solidification kinetics.The model addresses the following: (1) a rheology-viscosity model of the interference between moving particles, (2) engulfment (entrapment) or pushing of particles in the mushy region by the advancing solid/liquid interface, (3) nucleation and growth of equiaxed and eutectic phases, (4) effects of particle size, particle concentration, and cooling rate on the final grain size, and (5) the impingement effect of particles on the nucleation and growth kinetics of solidifying microstructure.Parametric studies were conducted using the computer model to investigate the effects of various process and material parameters on the distribution of TiC particles. The effects of the volume fraction, size, and morphology of the particles (including clusters and agglomerates) on the particle distribution were evaluated in detail. The complex interaction between the solidifying structure and insoluble ceramic particles in centrifugally-cast metal-matrix-composites was also investigated.The model predictions of particle distribution and microstructure were validated with experimental data for centrifugally-cast A356/SiC and TiC/Al-bronze alloys.This work was conducted by the National Center for Excellence in Metalworking Technology, operated by Concurrent Technologies Corporation under contract No. N00140-92- C-BC49 to the U.S. Navy as part of the U.S. Navy Manufacturing Technology Program."

Jan 1, 2000

By E. Daniel Baker

"The term ""oxide disseminated gold deposits"" refers to near surface, gold-bearing veins, faults, and shear zones that typically contain appreciable amounts of oxidized ore or gossanous material, resulting from oxidation of sulphides.The concept of oxide gold deposits underwent a dramatic change after the discovery of the Carlin gold mine in north-central Nevada in the early 1960's. Now the term implies large tonnage, low-grade bulk minable deposits that are processed by milling and/or heap leach methods.Oxide gold deposits may now be classified into two types: (1) primacy ores derived directly from the effects of hydrothermal alteration on host rocks, and (2) secondary oxide ores derived from the supergene oxidizing effects of circulating post-mineral meteoric waters on gold-bearing sulphides. Each type of deposit has unique diagnostic mineralogic and metallurgical characteristics that must be addressed to achieve successful exploration strategies and viable metallurgical exploitation.The author would like to thank the management of Newmont Metallurgical Services and Newmont Mining Company for allowing presentation of this paper. Thanks are due Sevkett Acar, Donald M. Hausen, Jerry R. Odekirk, and D. Erik Spiller for their critical review of the manuscript. Also, thanks are extended to all those cited and uncited whose hard work and dedication have led to the discovery and exploitation of near-surface oxide gold deposits. Our knowledge would be greatly limited without the dedication and research of many others."

Jan 1, 1997

Carbon injection into metallurgical slag is important in electric arc furnace (EAF) steelmaking for foamy slag practices and in nonferrous slag cleaning operations. The current publication presents kinetic data for coal injection into EAF slag to understand the interaction between injected carbon and metallurgical slag. Coal particles were injected into EAF slag and the kinetics were followed by gas and slag analysis. The results were analyzed, in terms of fundamental rate equations for each possible reaction step, as a function of temperature and slag composition.

Jan 1, 2003

By Ravi S. Bellur-Ramaswamy, Daniel A. Tortorelli, Robert Haber, Nahil A. Sobh

We optimize continuous quench process parameters to produce functionally graded aluminum alloy extrudates. To perform this task, an optimization problem is defined and solved using a standard nonlinear programming algorithm. Ingredients of this algorithm include 1) the process parameters to be optimized, 2) a cost function: the weighted average of the precipitate number density distribution, 3) constraint functions to limit the temperature gradient (and hence distortion and residual stress) and exit temperature, and 4) their sensitivities with respect to the process parameters. The cost and constraint functions are dependent on the temperature and precipitate size which are obtained by balancing energy to determine the temperature distribution and by using a reaction-rate theory to determine the precipitate particle sizes and their distributions. Both the temperature and the precipitate models are solved via the discontinuous Galerkin finite element method. The energy balance incorporates nonlinear boundary conditions and material properties. The temperature field is then used in the reaction rate model which has as many as 105 degrees of- freedom per finite element node. After computing the temperature and precipitate size distributions we must compute their sensitivities. This seemingly intractable computational task is resolved thanks to the discontinuous Galerkin finite element formulation and the direct differentiation sensitivity method. A three-dimension example is provided to demonstrate the algorithm.

Jan 1, 2001

By Jing Zhan

The fibrous precursor can be obtained by coordination precipitation process, using oxalate, cobalt chloride and ammonia. The composition and morphology of fibrous precursor were characterized by XRD, IR, DTA/TGA and SEM analysis. The results show that XRD pattern and composition of the precursor with fibrous morphology precipitated at pH=9.0 were different from that of ß-CoC2O4?2H2O precipitated at pH=1.0. The mechanism on the thermal decomposition of fibrous precursor was addressed. The influences of various conditions in pyrolysis, including the temperature, time, atmosphere, and the morphology of the precursor, on the morphology, average size and specific surface area of the Co powders were investigated in detailed. At last, the final product, fibrous cobalt powders with diameter about 0.3~0.5µm in size and 40~60 in aspect ratio, were produced by thermal decomposition at 400~500? in the weak reducing atmosphere. The structure of pores in cobalt powders was capillary tube with open ports and the majority was mesoporous.

Jan 1, 2009

By Wang Zhi

High-Mg-content concentrates are usually treated in Jinchuan flash smelting Furnace. Because the viscosities of high-Mg-content slag is very high, the operation of flash smelting becomes very difficult. To solve this problem, the viscosities of the semi-synthesized FeO-MgO-SiO2 slag of different compositions were measured. The results showed that when in the slag the weight percentage of MgO [w(MgO)] is 6-10%, the ratio of the weight percentage of iron to that of Si02, w(Fe)/w(Si02) is 1.1-1.4 and the temperatures are within 1473-1773K, the slag viscosities increased with the increase of W(MgO) and w(Fe)/w(SiO,). When w(Mgo)<6%, the smelting temperature should be controlled at I 300°C in order to to keep the smooth operation. When w(MgO)>10%, the temperature should be kept above I 633K. When the content of MgO is higher, a lower viscosity slag can be produced by decreasing the ratio of w(Fe)/w(SiO,). The appropriate ratio of w(Fe)/w(SiO,) for Jinchuan flash smelting furnace is about 1.2.

Jan 1, 2003

By F. -Z. Ji

Carbon injection into metallurgical slag is important in electric arc furnace (EAF) steelmaking for foamy slag practices and in nonferrous slag cleaning operations. The current publication presents kinetic data for coal injection into EAF slag to understand the interaction between injected carbon and metallurgical slag. Coal particles were injected into EAF slag and the kinetics were followed by gas and slag analysis. The results were analyzed, in terms of fundamental rate equations for each possible reaction step, as a function of temperature and slag composition.

Jan 1, 2003

By D. B. Dreisinger

The zinc pressure leach process developed by Sherritt Gordon, Ltd. permits the direct leaching of sulphide concentrates according to the overall reaction, ZnS +H,zS04 +402.+ZnS04+H20 +S0 The kinetics of the leach are affected by three rate controlling steps; ( l) oxygen mass transfer from the gas to the leach solution, (2) homogeneous oxidation of ferric ion to ferric ion by dissolved 011.ygen and (3) ferric ion leaching of zinc sulphide in the presence of a sulphur dispersing detergent (lignin sulphonic acid). Fundamental studies have been conducted to identify the factors that influence the kinetics of each individual rate controlling step. Oxygen mass transfer studies have been directed toward optimization of the agitator configuration for solids mixing and gas pumping from the atmosphere above the leach slurry. The rate of ferrous oxidation by molecular oxygen and the rate of zinc sulphide leaching by ferric ion have been studied over a wide range of temperature and solution compositions. The study of zinc sulphide leaching by ferric ion was supplemented by a series of interfacial tension measurements in the liquid sulphur - zinc sulphate solution system. The various kinetic studies have been summarized in terms of the importance of each rate to the performance of the process.

Jan 1, 1990