Search Documents

By E. S. Geskin

"This paper is concerned with the construction of a formal technique for the selection of a metallurgical technology. Exergy consumption is used as the criterion of process efficiency. Different items of the exergy balance are considered and techniques for the reduction of exergy consumption are determined. The selected techniques of exergy saving enable us to identify processes which should be used at different stages of steelmaking. The combination of the selected processes enables us to suggest a technology for conversion of iron ore into steel products. The selection of this technology narrows the range of further search of metallurgical processes. The paper shows that qualitative thermodynamic analysis can be used as the first step in the design of metallurgical processes. IntroductionThe existing processes for making, shaping and treating of steel enable us to convert the available iron bearing ores into marketable steel products. However, the energy cost of metal production is much higher than thermodynamically required, while the metal properties are much lower than thermodynamically available. Increasing cost and declining availability of energy and raw meterials make the creation of new steelmaking technologies imperative. In recent years, the number of novel processes for the making, refining, and shaping of steel have been suggested and tested. Some found a practical application. However, the tested technologies make up a small portion of the physically available routes for the conversion of iron ore into a marketable product. It is also not evident that the optimal routes have been tested and that the selected technologies are the best among those tested.Although the development of new metallurgical technologies must be based on the experimental and practical information, the number of the alternative routes for the making, shaping and treating of steel, as well as the cost of examining each single route, make necessary the use of analytical techniques for the evaluation of the possible ways of process development."

Jan 1, 1988

By C. R. Palmer

The Bureau of Mines investigated the use of ion-exchange technology for the recovery of precious metals from cyanide leach and spent electrolytic solutions. This research included adsorption of gold and silver on both weak-and strong-base anion-exchange resins. The effects of nickel, mercury. and iron on precious metal loading of strong-base resins were also determined. Due to the nonselectlvity of strong-base resins, selective elution also was investigated. Both commercially available and experimental weak-base anion-exchange resins were tested. None of the commercial weak-base resins tested were suitable for a caustic-cyanide system owing to their low recovery of precious metals at pH 10 or above; however, three experimental resins have possible application. Continuous tests conducted with mill cyanide solution in a multicompartmented ion-exchange column using strong-base anion-exchange resins adsorbed nearly 100 pct of the precious metals as well as the iron and nickel. During the elution of this loaded resin the iron was first removed with NaCI plus NaOH; then nickel with dilute H2S04 or HCl; finally gold and silver with thiourea in dilute HCl.

Jan 1, 1988

By Yavuz Ali Topkaya, Aydin Rusen

"In this study, zinc and lead recovery from zinc plant leach residue obtained from Çinkur using hydrometallurgical methods have been investigated by laboratory scale experiments. Considering more than one million tons leach residue (LR) rich in Zn (12.43%) and Pb (15.51%) in the stockyard and environmentally hazardous, it is essentially necessary to process Çinkur LR. Zinc and lead have been recovered in two main stages. As a first step, Çinkur LR was releached by using hot sulphuric acid for zinc recovery. About 72 % Zn was recovered by using 150 g/l H2SO4 at 95 oC in 2 hours with a pulp density of 200 g/l. Secondly, for lead recovery brine (NaCl) leaching tests were performed on the secondary Çinkur LR obtained after acid leaching process. In brine leaching while lead recoveries up to 95 % could be attained at a low pulp density, the maximum recovery obtained was 84.9 % at a high pulp density (200 g/l) with 300 g/l NaCl concentration in 10 minutes at 95 oC. Introduction Zinc and lead have been known and used by humans since ancient times and also they are important nonferrous metals [1]. Zinc and lead have different properties thus they are used in various application areas, ranging from automobiles to construction, from batteries to textile. Zinc and lead deposits are widely distributed in the Earth’s crust. The principal ore mineral for zinc is zinc sulfide, Sphalerite (ZnS), and lead sulphide, Galena (PbS), is the main source of lead in the world [2].Although zinc is generally produced from sulphidic ores (ZnS) or concentrates by Roast – Leach – Electrowinning (RLE) in the world, in Turkey, zinc production is based on zinc carbonate ores (ZnCO3), and at the Çinkur plant zinc was produced from zinc carbonate from its establishment to 1997 due to high reserves of zinc carbonate in that region. Çinkur is the only plant in Turkey that produces Zn from primary ore containing ZnCO3 by Waelz – Leach - Electrowinning route [3]. However, due to depletion of local high grade ores, oxidized ore concentrates were imported from Iran after 1997, until this plant was shut down. Therefore, there are two different leach residues (LR) which are Turkish LR (TLR) and Iranian LR (ILR) in Çinkur stockpiles. It has been estimated that the total amount of leach residue is more than one million tons of which the major part is Turkish leach residue (TLR)."

Jan 1, 2008

By Donald L. Stewart, Ken Overfield, Edward M. Williams

"Recent increases in energy cost have lead to a renewed focus on energy efficiency during aluminum melting operations to reduce fuel usage. The goals of a batch melting operation are to melt the charge using the minimum required energy, to melt the metal to the required temperature within the required timeframe, and to avoid generating unwanted contaminants by overheating the charge.The heat transfer efficiency of a conventional hydrocarbon fired aluminum melting furnace varies over the course of the melt cycle, depending on the conditions in the furnace. The purpose of this work was to develop a method of determining the transient heat transfer efficiency throughout the furnace cycle and to take advantage of this knowledge to optimize the melting process through furnace controls and proper production operations. This furnace survey methodology has been developed and used to evaluate a number of furnaces.Description of a Typical Batch Melting Furnace CycleA typical batch melting furnace cycle will consist of three stages:1. Charging – Solid metal charged through an open roof, solid or molten charged through an open door, and/or molten poured through a furnace blister2. Melting – From the time the door or roof is closed and the burners are turned to high fire until the charge is all liquid and has reached a temperature suitable for alloying (typically ~1350 °F / 730 °C)3. Holding – From the end of the melting stage until transfer or casting is completeIn some cases, further charging can take place after the melting cycle has started. This can happen when the entire solid charge will not fit in the furnace in one load, or if additional molten metal is added while the charge is melting. The bulk of the energy used in the melter is consumed during the melting cycle. The thermodynamic minimum energy requirements for melting pure aluminum are:• Energy required to heat pure aluminum from room temperature to the melting point at 1220°F (660°C) is 288 BTU/lb (670 kJ/kg)• Energy required to change state of pure aluminum from solid to liquid (heat of fusion) is 171 BTU/lb (397 kJ/kg)• Energy required to heat molten from melting point at 1220°F (660°C) to 1350°F (730°C) is 36 BTU/lb (83 kJ/kg)• Total energy required to melt a solid charge from room temperature to 1350°F (730°C ) is 495 BTU/lb (1151 kJ/kg)"

Jan 1, 2009

By Rongshan Qin, Dengfu Chen, Yan Zhao, Mingtu Ma, Yang Li, Xinming Wan

A two dimensional cellular automaton (CA) model coupled with finite element (FE) method has been developed for simulating the formation of solidified microstructure during beam blank continuous casting, which represents columnar and equiaxed dendrites growth in the case of detailed secondary cooling boundary conditions. In this model, a new adaptive mesh division is proposed to couple CA cubic lattice and irregular FE mesh of beam blank. A double-accuracy liner interpolation method is employed to obtain micro CA temperature field via macro FE calculation. The nucleation process and the velocity of dendrite tip are calculated by continuous nucleation model and KGT model, respectively. Moreover, the preferred orientation of dendrite growth is determined using a probabilistic model. The effects of super heat and casting speed on the microstructure characteristics are analyzed. This model can be applied to optimize processing parameters for beam blank continuous casting basing on microstructure evaluation.

Jan 1, 2015

By Hua Hou, Xiaofeng Niu, Wei Liang

"The explicit finite difference (EFD) method is used for calculating the casting temperature field during solidification. Because the time step is limited, the computational efficiency of the EFD method is lower. In order to improve the computational efficiency, a fourth-order in space and second-order in time model based on the equivalent specific heat method and the alternating direction implicit (ADI) method is established. The degree of similarity between the simulation results and the experimental results is analyzed. The results show that the simulation results of this high order mathematical model are close to the experimental results.IntroductionThe 3D heat transfer equation of temperature field during solidification process is as the following: [1-3]."

Jan 1, 2013

By Kandipati Sreenivasarao

Ion flotation is a promising separation process for continuously removing toxic metal ions from dilute process effluents. After treating the effluent with appropriate surfactant(s), the metal- bearing species adsorb onto the surface of rising gas bubbles and can be collected as foams. Suitable collectors have been identified for most of the elements of the periodic table. However, a better understanding of the thermodynamic, kinetic and engineering principles that determine the performance of ion flotation systems would facilitate commercial utilization of this technology. A model system of sodium dodecylsulfate-ethanol has been studied for the removal of Cu (11) from dilute solutions, using laboratory-scale flotation columns. This paper reports the effects of the air flow rate, solution height, foam drainage zone height and col1ector:metal ion ratio on the flotation kinetics, ultimate recovery of metal, flotation product grade, foam losses and effluent quality. Preliminary results for Pb (11) removal are also reported.

Jan 1, 1993

By A. Raraz

The optimization of the plutonium electrorefining process has been studied on the basis of modeling and model materials. The plutonium electrorefining process has been reviewed and the basics of the electrorefining process with molten salts as electrolytes and under forced convection has been presented. The definition of the problem in plutonium electrorefining has been related to three factors and this research has addressed these three factors to provide an insight to this process. The hydrodynamic factor gives information on the behavior of the mechanically stirred system. The chemical stability and solidification factor shows the interactions among the components of the electrorefining cell. The electrochemical factor is oriented to study the efficiency of the electrorefining process on the basis of limiting current density, stirring rate and configuration cell. As a result of this study the optimization of plutonium electrorefining implies mainly a re-design of the cell.

Jan 1, 1995

By W. P. lmrie

The recent years have seen many copper smelting operations become uneconomic due to a combination of low metal prices, high energy and labor costs, environmental requirements and high investment costs for modernization or replacement. Since a copper commodity requirement remains, the industry will recover, but many operations will need to determine which processes can offer the best prospect for economic operation and readiness for reliable investment and implementation. Corporate investment decisions involve the judgment of many factors in addition to topical technical aspects. Consideration of plant management and operational aspects are thus included. Taking account of such proven processes as conventional, flash and continuous smelting, plus modified conventional and new unproven processes, this paper gives a systematic approach to aid optimum choice for a modernization or grassroots investment. Actual achievements in energy form alternates, conservation and cost effectiveness are highlighted, and areas of remaining potential for energy saving are discussed.

Jan 1, 1983

By Saskia Duyvesteyn

Ion flotation is a technique applicable to the removal of metal ions from dilute solutions, using ionic surfactants.- While there are a number of physical and chemical parameters that influence the ion flotation process, this paper focuses on two of the important chemical ones, namely frother concentration and ionic strength. The effect of several frothers, including ethanol, iso-propanol and MIBC at concentrations ranging from 0% to 0.4%, was studied for the model Cd-dodecylsulfate and Cu-dodecylsulfate systems. The ionic strength, as well as the effect of monovalent and multivalent counter ions, was also studied in the range of 1@3 - 1 M, at constant pH. The results are discussed in terms of applicability to a range of effluents from minerals and materials processing operations.

Jan 1, 1994

By Jun-ichiro Yagi

A mathematical model has been developed for simulating the blast furnace operation with carbon composite agglomerates charging based on multi-fluid theory and reaction kinetics. In this model, the behaviours of carbon composite agglomerates are considered on the basis of previously reported conservation equations and experimental research on the reduction rate of carbon composite agglomerates. A series of calculations are performed to examine the effect of charging carbon composite agglomerates. The model calculation gives two-dimensional distributions of process variables and information on the overall operational parameters. It reveals that in-furnace temperature levels significantly decrease and the reduction of carbon composite agglomerates is retarded with carbon composite agglomerates charging ratio. The furnace performance is remarkably improved with the increase in carbon composite agglomerates rate. The productivity tends to increase while coke rate and total reducing agent rate show decreases at the different degree.

Jan 1, 2006

By Min Chen, Cui-huan Huang, Zhen Tian, Jian-hong Dong

"The present work studied the production of Fe-Si-Mn alloy from adjusted converter slag by thermodynamic analysis. The results showed that solubility of SiO2 in the molten slag increased with increment of temperature, and it is about 80% at 1800 ?. With increment of SiO2 content, a(MnO) and a(CaO) decreased, and a(FeO) increased to the maximum when w(SiO2) is about 30%. As a result, the reduction of the slag was in the order of Fe?Mn?P before SiO2 reduction, the reduction order was Fe?P?Mn?Si when SiO2 content in the slag was from 46.4% to 54.2%, and changed to Fe?Si?P?Mn when SiO2 content exceeded 54.2%. The mass fraction of Si in the alloy phase increases with increasing of w(SiO2) in the slag, and the mass fraction of Si in the alloy reached to 62.2% at 1800 ?.IntroductionFerroalloy production is a high energy consumption and high pollution industry[1-2]. If ferroalloy production could be produced from molten slag by addition of carbon-reducing agent, the valuable metal and oxide in the slag can be recycled, most importantly, if the high-temperature resource carried by molten slag can be made full use in the field of ferroalloy production, the power consumption of ferroalloy production could be cut down greatly.Converter steel slag is a kind of byproduct in steelmaking processing increasing rapidly with the increment of crude steel, but the utilization ratio is low. Most heat recovery research is still in the experimental stage except the heat recovery of blast furnace slag by water quenching method, at present[3-4]. It is of great significance for enterprises to energy saving and emission reduction if the molten steel slag could be utilized directly. Not only the reuse methods of liquid steel slag material can be promoted, but also the use of heat carried in the slag could be achieved. The basicity of converter slag is high and the activity of SiO2 is low so the reduction of SiO2 in the slag is little. The compositions of slag and metal phases were calculated by Factsage program on different conditions to explore the reduction of converter slag for recovery of valuable metals and an efficient new way to use the high-temperature heat combining with the current reuse and research status of converter slag. Further, the improvement of components activity in slag and the increase of Si concentration in the metal were also dicussed."

Jan 1, 2012

By G. A. Eltringham, A. F. Sarofim, A. A. Shook, M. P. Heap, B. R. Adams, K. A. Davis

This paper discusses the use of a reacting CFD model to determine chalcopyrite kinetics in a drop tube furnace and to predict the reaction of a chalcopyrite concentrate in the reaction shaft of an industrial smelter. Reacting CFD codes can be applied to determine the consequences of the interaction of gas with particles and therefore improve the ability to derive kinetic parameters that take into account the different temperature and oxidation histories that different particles will see. This paper describes the application of such a model to derive improved kinetic parameters for the pyrolysis and oxidation of chalcopyrite. The improved kinetic parameters derived from the drop tube studies are used to simulate chalcopyrite concentrate reactions in the reaction shaft of an industrial smelter. The reaction shaft model includes the effects of turbulent fluid mechanics, entrained flow mixing, turbulent particle dispersion, heterogeneous particle reactions, radiative and convective heat transfer, and surface and bath deposition rates. Particle reaction and composition characteristics are predicted as a function of particle trajectory and deposition and are used to aid in evaluating shaft performance.

Jan 1, 1999

By Ho-Jung Shin

The influence of cooling rate from 1873 to 1473 K on the size and morphology of austenite grains was studied using a Fe-O.I5 % C-I.5 % Mn alloy. The experiments were carried out at three different cooling rates of O.33KJsec, O.67KJsec and air-cooling. The austenite grain showed an isotropy at 0.33KJsec but maximized anisotropy at O.67KJsec and become much less. anisotropic. In order to account for these phenomena, a model was developed for estimating the size and morphology of austenite grains as a function of cooling rate. The driving force for the )( phase formation from 0 phase is caused by undercooling degree due to cooling rate and energy barrier is restricted to the misfit strain energy which is caused by mismatch between )( phase and 0 phase. The )( phase from 0 phase could be formed on not random orientation index systems but specific orientation systems depending on cooling rate.

Jan 1, 2001

By Dennis J. Kemp

Laterite projects are found in the tropical and sub-tropical regions of the world. As a result severe meteorological situations accompany such projects, often in regions of high seismic activity and political uncertainty. Frequently, socio-economic development supported by political interest is a major driver for development, while environmental protection imposes numerous stresses on the project. This paper will review and examine the many social, environmental, technical and financial issues that a mining and extraction process is subject to during development. The options that must be evaluated will be discussed in the context of sustainable development. Issues of project standards and cultural impact through to long-term issues such as greenhouse gasses and climate change will be assessed in redirecting project environmental norms. Although a rationale for sustainable project can be developed many long- term uncertainties around issues remain. Keywords: sustainable development, communities, social issues, standards, energy, waste management, consultation, agreements

Jan 1, 2004

By Ronald Klepper

In hydrometallurgy, pure gases like oxygen and hydrogen are used for oxidation and reduction. The gases are expensive and therefore should be used efficiently. Non reacted gas can be recycled into the liquid. Historically vortex gassing has been used; Le. a mixing impeller close to the liquid surface entrains gas from the headspace into the liquid through a gas vortex. Novel and more efficient methods are surface gassing with up pumping impellers and self- inducing gassing impellers. These alternative impeller systems are well established and common in the chemical industry, but have not been used until recently in hydrometallurgy. Gassing impellers act as internal compressors and increase the interfacial surface for a much higher mass transfer compared to alternate methods mentioned. In the paper results from lab and pilot tests and data from operated plants will be presented. The reactions with gases normally take place under moderate to high pressure, therefore a safe enclosure with mechanical seals and the safety "philosophy" is important. Experienced life and replacement cycles will be reported.

Jan 1, 2000

By Alexandre Bonan

This paper reports the results of a kinetic study on the oxidation of free cyanide and Cu-cyanide complex ions with HO,. The variables and respective ranges studied were the following: [CN] total =10 - 500 mg/l; pH=10-11; (H2O2/CN) mole ratio = 1- 3; (Cu/CN) mole ratio = 0.10 - 0.25. The results were interpreted by a semi-empirical model that incorporates the useful oxidation reactions and the parallel alkaline decomposition of H2O2

Jan 1, 1994

By John Demol

Monazite, a rare earth and thorium phosphate mineral, is one of the major minerals processed for extraction of rare earths. Industry practice for treating monazite concentrates is to use either a sulfuric acid bake or caustic conversion route. In the sulfuric acid bake, monazite concentrate is mixed with concentrated sulfuric acid and roasted. The rare earth phosphate mineral is converted to rare earth sulfate which dissolves in a subsequent water leach. As the bake temperature increases above 300 °C, thorium becomes less soluble. Although acid baking is practised in industry, the bake reactions are not well understood. A combination of chemical analysis, XRD and SEM-EDS was used to identify reaction processes occurring during sulfuric acid baking of a 93 wt% monazite concentrate between 200 °C and 800 °C. The effects of these reactions on the leachability of the rare earths, thorium and phosphate were also examined.

By Gervais Soucy

During mineral and industrial processing, contaminated wastewater can be generated such as cyanide liquors (free species or in complex form). This paper presents the treatment of cyanide solution derived from the aluminum industry, by direct contact of the solution with thermal plasma in a novel reactor. The reacation energy is provided by a plasma submerged in solution which allows direct contact between the plasma and the solution to be treated. The scope of this' study was to determine the feasibility of treating free and complex cyanides in solution through mini-pilot scale operations. An innovative reactor was designed and fabricated to provide stable: process operating conditions. Many parameters were studied. These experiments permitted the evaluation of the kinetics of complex cyanides decomposition under thermal plasma conditions. At atmospheric pressure (temperature about 100°C), the rate of cyanide decomposition by thermal plasma was 12 times greater than that of thermal hydrolysis in a plug flow reactor et the same temperature. The improvements in the decomposition rates are attributed to high thermal gradients at the plasma liquid interface and photocatalysis induced by the plasma UV radiation.

Jan 1, 1998

By Karl-Michael Zett, Marcus Kirschen, Ashraf Hanna

"Bottom purging systems are well established practice in refining metallurgy and an increasingly important technology for the EAF process in steel industry. Direct bottom purging provides efficient mixing of the entire melt volume, increases turbulence intensity in the melt, and improves mass exchange of alloy additions or oxygen. Continuously rising columns of dispersed gas bubbles helps to increase removal of volatile components carbon monoxide and hydrogen avoiding boiling retardation. Direct purging (DPP) systems provide cost benefits especially for EAF processes where metallurgical constraints have to be considered, e.g. for alloyed and stainless steel production, foundries. Case studies are presented.IntroductionCurrent EAF Technology and Production Constraints in Steel IndustryApproxinlately 30 % of steel, 446 Mio. tonnes in 2011, was melted in the electric arc furnace (EAF) with increasing tendency due to its large flexibility in production volume and raw materials. With recent increase of prices for ferrous raw materials the requirements for production of high quality steels from low quality scrap, direct reduced iron (DRI) and blends of ferrous raw material in various qualities increased. Maximum yield of ferrous raw material, oxygen, carbon, and alloys and minimum energy costs are of high importance. At modem high productivity levels even small process improvements provide considerable cost savings. Such improvements are caused, e.g., by efficiency increase of mass and energy transfer in the EAF. Optimization of flow pattern in the steel bath is therefore important for efficient melting of scrap and DRI and high homogeneity of the melt [1-4]."

Jan 1, 2013