Search Documents

By Yong-Moo Cheong

When the zirconium pressure tube(PT) is in contact with the calandria tube(CT) in the pressurized heavy water reactor(PHWR), the temperature gradient between the inner and outer wall of the PT results in a thermal diffusion of hydrogen(deuterium) and hydride blisters are formed on the outer surface of the PT. Since Zr-2.5Nb pressure tubes have a high risk for the formation of blisters during their operation in a PHWR, there is a strong incentive to develop a method for the non-destructive detection of the blisters grown on the tube surfaces. However, because there is little mismatch in an acoustic impedance between the hydride blisters and zirconium matrix, it is not easy to distinguish the boundary between the blister and the zirconium matrix with the conventional ultrasonic methods. This study has focused on the development of an ultrasonic method to detect the hydride blisters formed on Zr-2.5Nb pressure tubes. Hydride blisters were grown on the outer surface of a Zr-2.5Nb pressure tube using a cold finger attached to steady state thermal diffusion equipment. Ultrasonic velocity ratio method as well as conventional ultrasonic parameters with an immersion technique was developed to detect small hydride blisters on the Zr-2.5Nb pressure tubes.

Jan 1, 2006

By Rashmi Ramesh

Zinc oxide nanoparticles and nanostructures form an active area of research in the recent years. It can be doped to modify electronic, optical and other properties. Synthesis and characterization of zinc oxide is of extreme importance in order to understand the structure property relationship in this material which is now being considered of importance next to carbon nanotubes. Microstructure of zinc oxide nanomaterial is extremely sensitive to the preparation conditions. Nanocrystalline pure and Mn and Mg doped zinc oxide samples were prepared by wet-chemical method under different growth conditions. The samples were investigated for crystalline phase, microstructure, morphology and luminescence characteristics. The effect of Mn and Mg doping on the characteristics of ZnO have been discussed.

Jan 1, 2010

By Sergio N. Monteiro

Jute fiber reinforced polymer composites are among the most investigated and applied natural composites. In this past decade the mechanical properties of these composites has been assessed for various types of test conditions. However, the reported results correspond mainly to short-cut jute fiber composites, which do not present the highest mechanical strength as compared to continuous fibers of the same kind. In order to complement these results, the present work evaluated the mechanical behavior, by means of flexural tests, of polyester matrix composites reinforced with continuous jute fibers. Bend tests were conducted in standard specimens with up to 40% of jute. Fracture analysis by SEM displayed the rupture mechanisms. The results showed an improvement in some flexural properties with incorporation of jute fiber. However, a low fiber/matrix interfacial stress was responsible for limitation in the values attained by some properties.

Jan 1, 2010

By Pengfu Tan

Lead blast-furnace bullion cools to near its freezing point in an operation known as copper drossing or hot drossing usually contains 0.02-0.06% copper. The removal of this copper is usually carried out in a batch operation known as sulfur drossing. Sulfur is stirred into the bullion at temperatures near its freezing point, and the dross of copper and lead sulfides that floats to the surface is skimmed off manually. A thermodynamic model has been developed to simulate the copper drossing. The phase diagram of Pb-Cu-S system has been calculated, and the effects of the process parameters, such as temperature, copper content, and sulfur content, on the drossing process have been simulated and discussed.

Jan 1, 2006

A three?stages countercurrent fluidized bed prototipe reactor to neutralize the SO2from smelter gases has been developed. For gases with 8 vol-%SO2, at 800°C and for 4 h mean reaction time of the limestone, the capture of SO2 is 99%, with off gases with 0.07 vol-%. For 2 vol-%SO2, the total capture of SO2 can be obtained at 750°C and 4 h reaction time. The calcine obtained contain a blend of unreacted limestone and calcium sulphatewith minor amounts of residual lime.

Jan 1, 2006

By Philip E. J. Green

Two of the cornerstones of total quality management, the use of statistical and problem solving tools, and the involvement of employees, are directly applicable to environmental protection. The reduction in variation decreases the chances of violations and mishaps. Involving employees in minimizing environmental impacts is critical. One mistake, even with the best technology, and your plant can be shut down, customers lost and fines and penalties imposed - your reputation and the environment damaged. Proven strategies for involving employees in environmental protection, and over-coming the frequently strong differences of opinions about what constitutes environmental protection, will be discussed.

Jan 1, 1992

By C. Kathryn Sole

The close proximity of cobalt and nickel on the Periodic Table and their frequent occurrence together in nature means that their separation in primary hydrometallurgical flowsheets is not only often necessary, but requires the use of innovative chemistry to achieve high selectivity. Today, increasingly stringent demands for the high-purity cobalt and nickel salts required for battery applications in consumer electronics, electric vehicles, and solar applications are again challenging the state of the art. The evolution of cobalt–nickel separations is traced from the basic precipitation technologies employed in 1960s, through commissioning of the first cobalt solvent-extraction plant in South Africa in 1974, to the commercialisation of organophosphinic-acid extractants (which provided a step-change improvement in selectivity) and their eventual widespread use in the 1980s and ’90s. This was followed later by their sulphur analogue, which enabled different possibilities for laterite processing in the new millennium. Separations in chloride media, which take advantage of the different speciation chemistries, and nickel extraction by oximes in ammoniacal systems are also discussed. More recently, chelating and solvent-impregnated resins have added further dimensions to the possibilities for flowsheet design and enabled higher purity products to be attained from both primary and secondary sources. Selected case studies and flowsheets are described.

By Shirleny Fontes Santos

Muscovite mica crystals lower than 15 mm diameter are discarded as waste in the mining area of Borborema-Seridó (BRAZIL). The objective of this work was the ore dressing and purification of this waste to be used in the preparation of pearlescent pigment. Muscovite was dry ground using knife mills and an ultrasound treatment. It was possible to achieve 67% of mica with particle size lower than 100 µm. This product was used in the preparation of brilliant pigments based on muscovite flakes covered with rare earth oxides (CeO2, PrO2, Ce0,95Pr0,05O2). The pigments were characterized by X-ray diffraction, thermal analysis and scanning electronic microscopy. The color of the resulting pigments was analyzed using the CIELAB method and it showed the following colors: muscovite-CeO2 ? yellow, muscovite-PrO2? black and muscovite-Ce0,95Pr0,05O2 ? orange. Those results have shown that ?trash mica? is suitable for use in pigment preparation.

Jan 1, 2010

By Patricio Barrios

In February 1996, ATLANTIC, COPPER completed the construction of a Project for Expansion and Environmental Improvements in its Smelter and Electrolytic Refinery located in Huelva. Following the expansion, the new operating concept is based on the simultaneous blowing of two converters, while increasing throughput in the Flash Furnace up to the level required to deliver matte to both converters. While the production level planned with the Project.(270,000 MTPY of copper from concentrates) was reached the following June, work since then has been carried out to optimize the new equipment .and to develop a new operating shedule. This paper describes operational experiences from the start up of the Expansion Project, difficulties encountered and operating improvements introduced, which have allow an increase of production levels up to 300,000 MTPY of copper.

Jan 1, 1998

By W. G. Davenport

Chapter 1 showed that flash smelting is a key step in extracting copper from sulfide ores. It also showed that there , are two versions of flash smelting: (a) Outokumpu flash smelting, which uses oxygen-enriched air blast and injects dry feed downwards into a hot furnace (b) lncoflash? smelting, which uses industrial oxygen blast and injects dry feed horizontally into a hot furnace. This chapter describes Outokumpu flash smelting.

Jan 1, 2001

By Patricio Barrios

The Rio Tinto Metal (RTMetal) copper smelter, located 5 Km from Huelva, Spain, began operations in 1970. Since then a series of expansions and modifications have allowed a progressive increase in copper production. Environmental considerations having become increasingly important, environmental protection has come to represent an important aspect of the investments in production. As a result, modifications have been carried out in the two existing acid plants: -Modification of the RTM I gas cleaning section to closed circuit. -Substitution of cascade filters and acid lines. -Modification of the RTM I plant to double absorption. The Expansion and Environmental Improvement Project, completed end 1995, will allow 270,000 t Cu and 800,000 t H2SO4 to be produced yearly, at the same time achieving a decrease in specific and overall emissions. RTMetal's goal is to be an efficient smelter, with the avowed intention of respecting the environment and adopting the best available technologies.

Jan 1, 1996

By N. V. . Panishev

The Bakal (South Ural, Russia) deposit of iron ore bearing iron carbonate (siderite) with the capacity of more than 1 billion tones belongs to the MMK. This ore cannot be fully processed via blast furnace technology because of high content of MgO. According to the investigations carried out in the USA and Japan in 1999-2004 the ITmk3 (Ironmaking Technology mark three) RHF technology is a breakthrough in Ironmaking. Four iron ore types (hematite, magnetite, high and low Al2O3/SiO2) were tested. Reduction, melting and slag removal can be achieved in just 10 min. The main objective of the investigation is to establish optimum operation conditions for the production of iron nuggets from iron carbonate bearing ore via the ITmk3 by means of the lab scale testing. Samples of iron ore and carbon reductant were chemically and physically analyzed. Green pellets were processed via a lab tube furnace to simulate RHF conditions. The nuggets and slag were chemically analyzed. This preliminary test work provides valuable information which may be used for large-scale testing in a commercially sized RHF.

Jan 1, 2010

By Yanjie Liang

Elemental sulfur and volatilization kiln slag(VKS)containing heavy-metal produced by smelter factories were used to produce sulfured building material. The effects of heating mode, material proportion (MSulfur:MVKS), size of waste particles and ratio of aggregate to filler(A/F) on the mechanical properties and leaching toxicities of solidified stuff were investigated. The optimal conditions for the solidification are stepped heating mode, 3:7 ratio of MSulfur to MVKS, particle size less than 150µm and 3/17 ratio of A/F. Under the above optimal conditions, the compressive strength of solidified stuff rises to 35 MPa, and water absorption is down to 4%-6%.Furthermore, when NaOH is applied as an additive in the process of solidification, the 2+concentrations of most heavy metals except Pb have reached the national leaching toxicity standard. The results of X-ray diffraction reveal that sulfured solidification is caused by the physical encapsulation rather than chemical transformation.

Jan 1, 2010

By Liyuan Chai

In this study, spent grain was used as an adsorbent for the removal of Hg(II) from aqueous solutions, the process parameters such as contact time, solution pH, adsorbent dose, and initial Hg(II) concentration were studied in batch experiments. The initial adsorption process was fast, 91.08% of adsorption occurred within 5 min and equilibrium was reached at around 30min. Adsorption process was found to follow pseudo-second-order kinetics. The equilibrium data were better fitted to Langmuir isotherm than Freundlich isotherm with the maximum adsorption capacity 41.36 mg/g. The structure and component of spent grain before and after adsorption of Hg(II) were investigated using scanning electron microscope(SEM) and energy dispersive X-ray analysis(EDAX), these analysis also confirmed the adsorption of Hg(II) onto spent grain. The results indicated that spent grain had potential as a new inexpensive adsorbent for Hg(II) removal from aqueous solutions.

Jan 1, 2009

By Jilai Xue

Oxygen gas bubbles generate on anode during Pb electro-deposition process in PbSiF6-H2SiF6 aqueous solutions at room temperature. Cell voltage varies as the bubbles formed on the anodes surface. The bubble layer on the anode makes a voltage drop that consumes energy in the Pb process, which can be reduced by applying ultrasound on the anode. The effects of ultrasound frequency and anodic current density were investigated with ultrasound on and off, alternatively during the Pb electrode-position process. The removing of the gas bubbles were recorded in association with a drop in the cell voltage. The cell voltage can be lowered by 4% - 6% with ultrasound, which has potential for energy saving in Pb production.

Jan 1, 2010

By J. E. Hoffman

The operation of the U .S Metals Refining Company, USMR Co. is defined below by the description of a variety of unit processes and operations the author encountered during his tenure with the operation, 1955 - 1978. The operations discussed include: sampling and sweating of radiators, processing of Indian Coin, treatment of insulated wire, baghouse and converter dust treatment, blast furnace and converter operation, the electric arc furnace, antimony control, selenium and tellurium products, electrolyte liberation with soluble anodes, and the precious metals refinery. These operations, although peripheral to the primary copper production circuit, were critical to the company's technological and economic base.

Jan 1, 2000

By Willem P. C. Duyvesteyn

A novel hydrometallurgical process for Escondida copper concentrates has been developed by The Minerals Laboratory of BHP. The Escondida Process consists of concentrate leaching, solution purification, electrowinning and residue flotation. Part of the copper will be sold as high grade concentrate and part as high purity SX-EW copper. Contrary to previous efforts for the development of a hydrometallurgical process for copper concentrates, this patented process does not advocate the total dissolution of copper. It only aims for the copper that is readily soluble in a mildly oxidizing environment with an ammoniacal or acidic lixiviant. Both lixiviants were studied, but ammonia was preferred because of fast kinetics at ambient temperatures and pressures. By controlling the oxidation potential, the formation of sulfate ions and, consequently, of an ammonium sulfate byproduct, is precluded. These mild leaching conditions also prevent the dissolution of unwanted impurities and result in the production of ultra-high purity electrowon copper. Solution purification is carried out by solvent extraction with LIX-54. The very high loading capacity of this organic results in a compact SX circuit, consisting of two loading, one scrubbing, and one stripping stage. As the organic is selective for simple copper ions, the copper amine complex is broken down and free ammonia is regenerated and recycled for leaching. High purity copper cathodes are produced in a conventional sulfuric acid based electrowinning system. One scrubbing step is needed to separate the ammoniacal circuit from the acid circuit. Limiting copper dissolution to less than 50% also provides an opportunity to produce high grade concentrates by residue flotation. Copper recoveries in excess of 98% with precious metal values reporting to the final concentrate can readily be obtained. Complete breakdown of the copper mineral- pyrite middlings results in a final concentrate grade that can be even higher than the original feed material. The Escondida Process also provides an opportunity to accept lower grade copper concentrates producing improved copper recoveries in the mill and yet high quality concentrates for marketing. The Paul E. Queoeau International

Jan 1, 1993

By Eric Pirard

Theoretical studies carried out on shape analysis supply mathematical tools to analyze the influence of grain shapes on ore beneficiation. In the case of statistic images like those encountered in applied mineralogy parametrical and harmonical analysis methods are used. It is important that the shape parameters are adapted to the specific processes involved in ore beneficiation, while remaining easy to manipulate. The inertia parameters are considered in the scope of granulometric and gravimetric processes It appears that they are able to distinguish between the resulting products where very popular shape parameters are not. The measured statistics are analyzed through discriminant analysis procedures in order to estimate the importance of morphological differentiation and the aptitude of shape parameters to account for this.

Jan 1, 1989

In this study, the method of chemical co-precipitation?reduction?diffusion was developed for the preparation of magnetic SmCo5 alloy. In the chemical co-precipitation process, the effects of solution pH, the reactant concentration, the dispersant on the process were investigated. The optimum conditions of the process were determined, and the SmCo5 alloy oxide precursor particles with fine crystalline structure, narrow size distribution was obtained. Then, by reduction-diffusion treatment of the precursor particles, the SmCo5 alloy with high quality was produced. It is anticipated that the co-precipitation-reduction-diffusion is a novel method available for SmCo5 alloy production.

Jan 1, 2006

By Lucas Lopes da Costa

In this work, a natural foam extracted from the Amazon buriti palm tree is investigated as possible substitute for synthetic foams. The basic physical and mechanical properties of this biofoam were evaluated. Its sponge-like structure was characterized by the amount of pores and morphological aspects. It was found that the buriti biofoam displays a very low density of the order of 0.1 g/cm3 with a relatively good compressive strength. This would be suitable for several engineering applications and as a new material with the potential for replacing currently applied synthetic polymeric foams.

Jan 1, 2010