Search Documents

By Itavahn Alves da Silva, Izabela Diniz Duarte, Carlos Antonio da Silva, Varadarajan Seshadri

Mathematical modeling using computational fluid dynamics has been employed to assess the thermal losses in a steelmaking ladle. Thermal losses lead to thermal stratification and convective flow inside the ladle. The effects of preheating, mineralogical and physical characteristics of the lining as well as thickness of slag cover have been studied and the results obtained from application of the model have been discussed.

Jan 1, 2016

By Isıl Kerti, Sibel Daglılar, Sinem Yıldırım

In this study, effect of rolling and coiling temperature in thermo mechanical controlled process (TMCP), on the microstructure and mechanical properties of dual phase (DP) steel according to martensite volume fraction (MVF) rate was investigated. By using various finishing mill exit temperature and cooling conditions that is controlled laminar cooling system, the microstructural evolution of coil improves the mechanical properties with lower costs and higher productivities, in comparison to the heat treatment after rolling. The main part of the paper contains the result of tensile, yield and microstructure properties of DP600 steel produced on hot strip rolling plant and run- out table line. The results show that a higher MVF and an increasing cooling rate after the last deformation raised strength of the DP600 steel. The yield strength and ultimate tensile strength increase by decreasing coiling temperature.

Jan 1, 2015

By Du Sichen, S. Seetharaman, Wei Liu

"The viscosities of two-phase mixtures are of great importance in the modelling of the fluid flow in metallurgical processes. For example, in steel making and refining, the intimate mixing of metal droplets in the slag phase requires a consideration of the effective viscosities for the mixture. The present work was aimed at an understanding the phenomena underlying the viscous flow in a two-phase mixture with widely differing viscosities.Emulsions of silicone oils of known viscosities (345mPa.S and 1010mPa.S at 293K) with small amounts of water evenly distributed in the same were prepared by subjecting the mixture to uniform stirring using a magnetic stirrer. The viscosities of these emulsions were measured at constant temperature by rotating cylinder method using Brookfield Digital Rheometer. The uniformity of the preparation of the emulsions was confirmed by the reproducibility of the results. Th7 measured viscosities were generally found to be independent of the torque under the experimental conditions so that the two-phase mixture could be considered as a Newtonian liquid. The variation of viscosities with temperature and the effect of addition of a surface-active substance were also studied in this work.The measured viscosities were found to be· higher than those of both pure water and silicone oil. The experimental viscosities were found to increase with increasing concentration of water. The influence of surface tension on the viscosities was examined by adding surfaceactive agent to the mixtures. The result is discussed and compared with theoretical models developed by Einstein, Taylor and Oldroyd."

Jan 1, 2000

By Cassandre Nowicki, Louis Gosselin, Carl Duchesne

"Quebec's primary aluminium production industry consumes roughly 39 TWh of electricity per year and is accountable for roughly 7 million tons of CO2 equivalent. By tapping only a small portion of waste heat and integrating it inside the production facility itself, we can significantly reduce GHG emissions and energy consumption. Although the amount of thermal waste can be adequately estimated by applying an energy balance to production processes, this provides very little information on the quality of waste heat and its potential for integration. A measure of exergy is required. Waste heat streams characterized by high exergy content may generally offer valuable incentives for recovery and integration. More generally, exergy values limit integration possibilities. An exergy analysis is provided for the aluminium electrolytic reduction process. This is meant to guide future heat recovery initiatives and energy efficiency measures.IntroductionCanada is one of the world leaders in primary aluminium production and 92% of its aluminium production capacities are located in the province of Quebec. In 2007, production capacity reached 2,786,000 tons in Quebec alone. Since it is estimated that 2.5 equivalent tons ofCO2 are released for each ton of aluminium produced in Canada, Quebec's aluminium production industry is accountable for roughly 7 million tons of CO2 yearly [1, 2]. Furthermore, with an average electricity consumption of 14 MWh per ton, primary aluminium accounts for 39 TWh of electricity per year in Quebec and this energy consumption represents 350 thousand tons ofCO2 equivalent [3, 4]. Natural gas consumption associated with primary aluminium production accounts for less than 1 TWh, but it represents an additional 350 thousand tons of CO2 equivalent [ 4].This work is meant to provide a tool to guide future efforts towards heat recovery and energy efficiency in the primary aluminium industry. Waste heat recovery and thermal integration can cut down both energy consumption costs and GHG emissions. In a primary aluminium production facility, waste heat represents roughly half of the energy input into the Hall-Heroult process. Tapping only a small portion of this energy could reduce natural gas and electricity consumption significantly. In order to evaluate how much of this energy is actually usable, we propose to apply an exergy analysis to individual transformation processes in an aluminium production facility, such that a potential to do work can be assigned to every waste heat flux. The approach will be described in the next section."

Jan 1, 2012

By Ernest D. Mast

Noranda's Altonorte custom smelter, located in the 2nd region of Chile, 20 kilometres southeast of the city of Antofagasta, started operations in 1993. Presently, 1150 tonnes per day of new feed are smelted with an 85% sulphur capture. An oxy-fuel reverberatory furnace produces a 48%-55% copper matte that is treated in 13 ft. x 36 ft. (3..96m x 10.97m) Peirce-Smith converters (two hot and one blowing). Up to thirty percent of the new concentrate is smelted via dry concentrate injection into the converters. This paper reviews the development of the concentrate drying and injection system, and oxygen enrichment at Altonorte from start-up in 1995 to the present time. The relationship between oxygen enrichment and concentrate injection is reviewed from a theoretical and practical standpoint. Concentrate injection has improved the smelter's productivity and added flexibility to the operations. Due to the relatively high matte grades and the subsequent short converting times, maintaining consistent operations was difficult at times and the smelter has gone through a learning curve. Plant operating results and experiences are presented on the impact of concentrate injection in relation to: feed treatment, blowing times, revert generation, slag quality and refractory wear.

Jan 1, 1999

By Michael A. Eamon

Magma Copper Company has operated its San Manuel SX-EW Plant facilities since 1986. The original plant facilities have a design capacity of 25,000 tons per year of electrowon copper cathode produced by processing pregnant leach solutions from an open pit/heap leach operation. In 1988, the plant was expanded to 50,000 tons per year to incorporate processing leach solutions from an insitu leaching operation. This paper presents a general overview of plant practices with particular emphasis on process innovations developed and implemented by Magma during construction and operation.

Jan 1, 1991

By R. H. Rubisov

Sulphuric acid pressure leaching of nickeliferous laterites has attracted considerable attention from the nickel industry during the past five years. The process is especially advantageous for limonitic laterites that mostly contain goethite, because iron precipitates releasing acid and thus rendering low acid consumption. It is also applicable to mixtures of limonites and saprolites, although at higher acid consumption due to magnesium. Effective process design requires the solubility of metals that precipitate during the process to be known. In the present work, determination of metal solubilities is based on a simple speciation program that assumes the presence of only one dominant complex for each metal. The thermodynamic data for the precipitation reactions are extracted from high-temperature experiments with monometallic systems published previously. The validity of the approach is then tested against mixed bimetallic systems, and finally applied to calculate the solubility of aluminium, iron and magnesium in laterite leaching effluents "at temperature". In both cases of limonitic feed and limoniticfsaprolitic blends, the prediction closely follows metal solubilities measured experimentally at temperatures from 230 to 270°C and at terminal he acidities ranging from 10 to 75 g/L.

Jan 1, 1999

By J. B. Winter

The present Inspiration Consolidated Copper Company Smelter/Acid Plant complex located near Miami, Arizona, was designed and built specifically to conform to the ambient air quality standards imposed by the Federal Clean Air Act of 1971. The present plant replaced a facility which had been in operation since 1915. The electric furnace, siphon converters and acid plant complex were commissioned in May, 1974 (1). At that time, the Plant was considered to be one of the most extensively monitored and instrumented facilities of its kind in the world. Several control areas were located in close proximity to the controlled process, in addition to so-called central control rooms in the Smelter and Acid Plant. The control rooms were staffed with officials below the foreman level. Instrumentation consisted of conventional analog devices, except for a computer used in monitoring ambient air environmental conditions and limited use of programmable logic controllers. The harsh service conditions prevalent in the plant rendered a significant portion of the instrumentation unreliable and, in many cases, inoperable. Failure of the facility to obtain the total sulfur collection for which it was designed was, in part, due to serious inadequacies in control system logic and sulfur recovery averaged 79% in the early years. After careful study of the smelting process, engineering hardware and high labor cost inherent in the organizational structure, management made a judgement decision to convert to centralized control of the process with high level supervision 24 hours per day. A distributed digital control system with supervisory arid data acquisition/information reporting computers was selected to satisfy the requirement of central control. Operations are now controlled and coordinated from a primary control room in the Smelter and a satellite control area in the Acid Plant.

Jan 1, 1983

By M. J. Collins

Direct pressure leaching of zinc sulphide concentrates was started? commercially in October 1980. Continuing research and development studies at Sherritt and feasibility studies for a number of clients have defined various pressure leach configurations for integrattons with existing roast- 1 each operations and for grass roots plants. Existing and potential applications of zinc pressure leaching are discussed.

Jan 1, 1990

By K. Osseo-Asare

The molecular structural and solution chemical characteristics that underlie the surface activity of solvent extraction reagents are highlighted, with particular emphasis on the tendency towards reverse micelle and microemulsion formation. The physicochemical factors that lead to microemulsion-enhanced solvent extraction with chelating extractants are elucidated Membrane-based contactor systems are described which are uniquely suited for enhanced solvent extraction with microemulsions. The possibility of combining solvent extraction with microemulsion-mediated materials synthesis is discussed.

Jan 1, 1996

By Guan-zhou Qiu, Shui-shi Liu, Yu-feng Guo, Tao Jiang

"The preparation of high-quality synthetic ruitle from electric furnace titanium slag was systematically investigated by activation roasting followed by acid leaching process. The results showed that impurities such as Ca and Mg in titanium slag can be effectively removed and TiO2 grade of the product was markedly improved by the process. High-quality synthetic rutile containing 88.54% TiO2, 0.42% (CaO+MgO) was obtained under the conditions that roasted with 7.5%(wt) H3PO4 at 1000 oC for 2h, followed by two-stage leaching in boiling dilute sulfuric acid for 2h. Mechanism studies showed that anosovite solid solution and silicate minerals were reacted with phosphoric acid in the roasting process. As a result, titanium components in titanium slag turned into rutile (TiO2) and impurities were transformed into acid-soluble phosphate and quartz.IntroductionWith the gradual depletion of natural rutile and the rapid development of titanium industry in China, the natural rutile reserves cannot satisfy the requirement for production of titanium pigment and titanium sponge. Ilmenite is, therefore, becoming main raw material for titanium industry. However, because of its low TiO2 grade, it generally requires preconcentration to titanium-rich material such as titanium slag or synthetic rutile [1-3].Ilmenite resources are extremely rich in Pan-xi area of China, which account for 90.54% of total ilmenite reserves in China [4]. The titanium slag produced by electric smelting of ilmenite concentrate has high contents of Ca and Mg, and is not suitable as a raw material for chloride process and titanium sponge production. Therefore, upgrading titanium slag to prepare raw material suitable for chloride process and titanium sponge production has important significance for the development of China's titanium industry."

Jan 1, 2011

By S. Z. El-Tawil, K. A. El-Barawy, M. B. Morsi, M. M. Nasr, Z. I. Zaki

"Tue sulphatization of zinc concentrate produced from heated zinc concentrate of Um Ghieg area, eastern desert by ammonium sulphate as sulphatizing agent is carried out at different conditions to achieve the appreciable formation of soluble sulphates. The maximum zinc recovery as soluble sulphate equfils to 95% upon using 1.5 stoichiometry ammonium sulphate at 600 °C for one hour. Tue obtained leached zinc sulphate solution is subjected· to purification process to prepare high pure zinc metal and zmc compounds such as pure zinc sulphate, zinc caibonate and zinc oxide. The products obtained are analyzed chemically and identified by X-ray analysisTue mechanism and kinetics of the sulphatization process of zinc concentrate are considered where the activation energy is calculated and equals to 33.3 K.J.mol""1 A process flowsheet for the overall sulphatization process of zinc concentrate by ammonium sulphate is proposed.IntroductionConsiderable reserves of zinc ores are present in Um Ghieg area eastern desert, Egypt. The possibility of extraction zinc from these ores and preparing its valuable compounds by choosing a more feasible technology become of vital importance. An attention is focused on the sulphatizing roasting processes (1-9) to achieve the appreciable formation of soluble sulphates. Previous publications are reported in our division by El. Tawil and others (10-16) using ammonium sulphate as sulphatizing agent for the successful treatment of nonferrous bearing materials.Therefore, the present work aims to study the different factors affecting the sulphatizing roasting process of local zinc coocentrate by anunonium sulphate to extract completely zinc and preparing its main compounds. Tue mechanism and kinetics of the different chemical reactloos that 1ake place in the process are considered."

Jan 1, 2000

By Yong Li, Tao Jiang, Xiangxin Xue, He Yang

"In this paper, we describe the current status and research progress on the utilization of typical industrial solid wastes in China. We propose a creative method called “eco-utilizing wastes” with an aim of both integration and increment but without second-time waste and pollution, in terms of the characteristics of typical industrial solid wastes, such as titanium-bearing blast furnace slag, high-silicon iron tailing and boron-enriched slag as well as oil shale.Situation of Typical Industrial Solid Wastes in ChinaThough mineral resources in China are abundant, most of these are low grade ores. Moreover, the distribution of mineral resources is asymmetric, which causes the increase of cost and decrease of the economic benefit. Over-exploitation of mineral resources results in a large number of solid wastes. The accumulation of solid wastes not only means the waste of valuable resources, but also causes environment deterioration. There exist some problems in the current practice of the disposal of industrial solid waste, such as only emphasizing the final results and causing new pollution and waste [1]. So the research and development of a high value-added method has a high practical relevance to our nation. Based on the present status and research progress of industrial solid wastes in China, a creative new idea and method for eco-utilization of solid wastes is proposed in this paper."

Jan 1, 2012

By Christina Viklund-White

Life Cycle Assessment has been used to compare the environmental performance of landfilling versus recycling of the zinc used for galvanizing steel. Hypothetical process routes were com-posed involving four different EAF dust treatment processes; Waelz kiln, DC-furnace, EZINEX and slag fuming, as well as scrap dezincing. The study shows that recycling of zinc used for galvanizing steel has environmental benefits in that it saves zinc resources. However, zinc recovery does not necessarily decrease the potential impact on global warming and acidification. The magnitude of these two impact categories is tightly correlated with the amount and type of primary energy consumed in a process. Due to the high electricity consumption in the dezincing process, this route has the highest impact on Global Warming Potential as well as Acidification Potential. The major part of the energy requirement for the production of zinc from primary and secondary sources is consumed in the reduction of ZnO to Zn. The consequence is that the theoretically possible savings in primary energy by recycling zinc-containing materials are relatively minor. The impact categories "land use" and "waste generation" are not considered in this study, but most likely the evaluation of such impacts would further increase the potential environmental impact of the landfill alternative. The results also show that the location of an electricity-intensive process highly affects the potential environmental impact. Comparing process and material alternatives in LCA studies where branch average data is used, is considerably more complex than when LCA is used within a company.

Jan 1, 2000

By C. J. Beyke

The U.S. Bureau of Mines has developed a process for the selective recovery of Pb metal from a mixed Pb-Zn concentrate. The concentrate was leached in recycled H2SiF6 at atmospheric pressure and 95° C with a redox potential of 570 mV (Eh). Eighty-five pct of the Pb was selectively leached from the concentrate while 87 pct of the Zn remained in the residue. Pressure leaching of the concentrate was slightly less successful, with 78 pct of the Pb leaching from the concentrate and 80 pct of the Zn remaining in the residue. Pure Pb metal was successfully electrowon from a purified PbSiF6-H2SiF6 solution with 96 pct current efficiency and 0.69-kW.h/kg energy consumption.

Jan 1, 1991

By Yuanbo Zhang, Zhixiong You, Daoxian Duan, Guanghui Li, Tao Jiang

"Manganese is mainly consumed by steel and battery industries. In recent years, it is essential to utilize the low-grade manganese oxide ores with total manganese grade below 25%, as the high quality manganese ore resources are becoming scarce with the rapid development of the steel industry. Conventional pyro-metallurgical processes for utilizing manganese oxide ores are characterized by high production cost and energy consumption, low productivity, serious environmental pollution, etc. In this study, reduction thermodynamic of MnO2 reduced by sulfur was firstly carried out. Then, a novel process of reduction roasting with sulfur followed by acid leaching was developed to recover manganese from the very low-grade manganese oxide ores. Effects of main factors, including temperature, reduction time and S/Mn mole ratio, were investigated, and a high leaching efficiency of Mn above 95% was obtained under optimal conditions.IntroductionHigh/middle-grade manganese oxide ores are generally used in the metallurgical industries, particularly in steel plants and ferro-alloy units. The consumption of metal manganese in the ferro-alloy industry accounts for 85- 90% of the total Mn demanded [1]. Therefore, high quality manganese ore resources are becoming scarce with the rapid development of steel industry. It is essential to make good use of large quantity of low-grade manganese ores (TMn < 25%) presently available."

Jan 1, 2012

By Donghai Li, Cheng Pan, Pan Chen, Xuewei Lv, Mei Liu

"Chromite concentrate after beneficiation can not be directly used in the electric furnace. Therefore sintering is one of the effective way to agglomeration, by which the chromite concentrate can be utilized and the power cost of ferrochrome smelting can be reduced. The properties of raw materials and the sintering process of chromite concentrate were studied in this work. The results showed that chromite concentrate used can hardly granulated alone, while chlorite addition can improve the effect of granulation. Moisture plays an important role in sintering process. The granulation effect is optimal when the amount of water addition is 12%. Strength and abrasion index are the evaluation indexes of sinter quality. It was found that the strength of sinter increased with coke dosage increasing to 12%, and then decreased when it continuously increased. Opposite regularities were found for the abrasion index of the sinter.1 IntroductionChromium is a very important metal element which is mostly used in the production of stainless steel. In the earth, it is always formed compound with iron as ferrochromium spinel (FeO.Cr203), and its mineralogical name is chromite.[1] Currently, the global production of chrome ore is about 20 million tonnage every year , in which fine ore (less than 8 mm) accounted for about 80% [2] Although the price of the fine ore is cheaper than the lump one, too much fines will lead to the poor permeability and causes increased electricity consumption while producing ferrochrome. Therefore, the agglomeration process of chrome ore is one of the effective measures to increase the usage ratio of fine ore."

Jan 1, 2013

By Minna Rämä

Iron containing leach residues like jarosite and goethite from electrolytic zinc production contain many valuable metals and harmful substances. These metals and substances should be removed in order to obtain an acceptable, stable and reusable product, and maximize economic feasibility as well as minimize environmental footprint. In this work, the processing of jarosite leach residue was studied in laboratory scale experiments under oxidizing and reducing conditions at high temperatures. First, the pretreated material was melted and oxidized to produce a melt of metal oxides. Second, the oxide melt was reduced in CO–CO2 atmosphere. Target after the reduction step was to obtain a clean slag and a liquid metal or speiss phase that collects the valuable metals, such as silver. The kinetics of the thermal processing were studied for determining optimal times and conditions for the aforementioned process steps. The preliminary results show that the process is thermodynamically feasible, and the desired phases can be obtained in the experimental conditions investigated.

By Mark William Kennedy

Modern metallurgical plants typically have complex flowsheets and operate on a continuous basis. Real time interactions within such processes can be complex and the impacts of streams such as recycles on process efficiency and stability can be highly unexpected prior to actual operation. Current desktop computing power, combined with state-of-the-art flowsheet simulation software like Metsim, allow for thorough analysis of designs to explore the interaction between operating rate, heat and mass balances and in particular the potential negative impact of recycles. Using plant information systems, it is possible to combine real plant data with simple steady state models, using dynamic data exchange links to allow for near real time de-bottlenecking of operations. Accurate analytical results can also be combined with detailed unit operations models to allow for feed-forward model-based-control. This paper will explore some examples of the application of Metsim to real world engineering and plant operational issues.

Jan 1, 2014

By A. Kar

A mathematical model is presented for pure titaqium deposition from titanium tetrabromide on a stainless-steel (SS 304) substrate. Five three-dimensional, transient, and nonlinear partial differential equations are used to account for the diffusion of various species inside the deposition chamber and the thermal decomposition of titanium tetrabromide, titanium dibromide, and titanium monobromide at the surface of the substrate in order to determine the thickness of the titanium film deposited on the substrate. The effects of various process parameters on the deposition and shape of titanium films are examined, and under certain conditions, the deposited titanium films are found to have volcanic profiles.

Jan 1, 1992