Search Documents

By Satu Jyrkönen

A single-particle laminar-flow technique was used to study oxidation of four synthetic nickel mattes, which were screened into three size fractions, Experimental conditions were: reaction gas from N2 - 21 to 75 vol-% O2; gas preheating temperatures ranging from 500 to I 100'C. The four mattes were synthesized so that Ni/Cu ratios of I and 10 were obtained with high and low iron contents. Chemical analysis of the particles was used to determine the oxidation degree of the materials, and optical and scanning electron microscopy were used to detect their morphology, internal composition and structure. The best sulfur removal from the synthetic nickel mattes was achieved under the most oxidizing conditions with the finest size fraction. The matte with Ni/Cu = 1 and high iron content was found to be most reactive. The least reactive matte was with Ni/Cu = 10 and low iron content; the coarse fraction particles did not react at all under the conditions studied.

Jan 1, 1996

By C. D. Mishra

The recycling potential for any gainful utilisation of the waste products is dictated by their quality, especially the chemical characterisation. The methods commonly used for the analysis of fly ash e.g. wet chemical, AAS, ICP-AES etc are time consuming. The paper describes a rapid XRF-based method for routine analysis of fly ash which involves preparation of local standards, optimisation of sample preparation technique and use of a simple PC-based software to account for interelement effects. The matrix corrected values are found to agree well with the wet chemical data.

Jan 1, 1992

By P. Maraboutis

Iron removal by precipitation as jarosite from Fe-Ni-Co sulfate solutions, (synthetic or real, resulting from laterites leaching) has been investigated. Precipitation was carried out at 95 C, and at an initial pH 1.6, which was either kept constant with CaCO3 or Li2CO3 additions, or left to drift with the evolution of the reaction to lower values. The precipitation of K-, NH4- and Na- jarosite was initially examined using synthetic solutions. In all cases, hydronium ions were incorporated into the precipitate as well. Residual iron in solution was lower (0.2-1 g/1) and equilibrium was achieved faster (within 4-8 h) when precipitating K¬jarosite at constant pH, using CaCO3 for neutralization. Nickel and cobalt losses were small. Na- jarosite precipitation was also studied from real solutions with high initial iron content, under constant pH=1.5, controlled with CaCO3 additions, and it was shown that low residual iron concentration in solution (0.3-0.5 g/1) can be achieved again, with relatively small nickel and cobalt losses. The thickening and filtration characteristics of the precipitates were excellent in all cases examined.

Jan 1, 1988

By Alistair Burrows

Situated in the oblast of East Kazakhstan, the Ust-Kamenogorsk Metallurgical Complex has spent the past twenty years renovating and remodelling itself as a modern polymetallic sulphide smelting facility, and a regional centre of excellence for custom smelting. Along the way there have been changes to the company structure, introduction of new technologies, investments in expanded capacity, environmental improvements, and addition of new metal products and by-products to the site’s repertoire. These changes have been gradual and incremental, but taken together they represent a significant contribution to placing Kazakhstan’s sulphide smelting industry on a strong foundation for enduring success in the international custom smelting market. In achieving these changes, a workforce that was historically isolated from much of the world now has recognised expertise, internationally competitive skills, and confidence to embrace the future. Further improvements in energy efficiency, environmental compliance and polymetallic processing capabilities are challenges that UKMC stands ready to face.

By Omid Marzoughi

In this research, both the kinetics and the mechanisms of the roasting of a sphalerite concentrate from the Bafgh mining complex in Iran were investigated. The oxidation process was performed in a muffle furnace in air and the effects of time and temperature on the degree of oxidation of the zinc sulfide sample were quantitatively studied. The experimental data were fitted to the shrinking core model. In the temperature range of 650–800 °C, the rate-controlling step was the chemical reaction between the zinc sulfide and oxygen with an activation energy of 103 kJ mol−1. On the other hand, in the temperature range of 850–950 °C, the rate-controlling step was oxygen diffusion with an activation energy of 50 kJ mol−1. Also, the roasting process was studied using thermogravimetric (TGA) and derivative thermogravimetric (DTGA) techniques.

By Jianhua Xin, Min Chen, Cuihuan Huang, Shan Yu, Xiaoao Li, Nan Wang, Guanghao Chen

Copper enrichment behavior in continuously cast slab induced by scale formation after continuous cooling in H2O vapor atmosphere and consecutively in air has been experimentally investigated by combining with SEM-EDS analysis, for the purpose to examine the effects of initial slab surface temperature and contents of copper and nickel. For Slab 1 with copper content of 0.1 percent, no visible copper enrichment is found at scale-substrate interface irrespective of the various scale microstructures formed at different initial slab surface temperatures. For Slab 2 with higher contents of copper and nickel, copper-rich phase accumulates and stays at scalesubstrate interface under the condition of lower initial slab surface temperature; while Cu-rich phase in the porous scale formed at higher initial slab surface temperature is noted with simultaneous Ni-enrichment appearing in front of the steel-scale interface. Both a porous scale and high nickel content work together to provide pores for copper-rich phase migration away from interface and occlude within the scale layer.

Jan 1, 2016

By K. G. Wang, M. E. Glicksman, P. Crawford

"We formulate the mathematical solution to late-stage multi particle diffusion in finite systems. The transition from finite system behavior to that for an infinite system is established. Large-scale simulations are reported regarding the dynamics of phase coarsening. Even in the case of a small volume fraction (Vv = 10-4), the particle size distribution is broader than that for the well-known Lifshitz-Slyozov limit at zero volume fraction. We also report the first simulation studies of extremely low volume fraction, for which corresponding experiments, as well as other simulations, do not exist at present for comparison. However, in the case of moderate volume fractions (Vv = 0.1), the fiucutations in the volumetric growth rate of particles are extracted from our simulations. These simulations provide additional insight into the statistical nature of diffusion interactions, including multiparticle stochastics during microstructural evolution.IntroductionPredicting microstructure evolution in alloys remains one of the cornerstones of materials science. Phase coarsening is a common process in microstrucural evolution that leads to a decrease in the excess total interfacial energy of the system. The system typically consists of separate and identifiable units, or domains, such as second-phase particles distributed in a matrix. During phase coarsening, larger particles grow at the expense of small particles. Over time, this ""competition"" results in an increase in the average size of the particle population, and in a concomitant decrease in the number of particles.Particle size and microstructure of many cast alloys depend on similar coarsening processes. Indeed, properties of these materials, such as strength, toughness, ductility, and electrical conductivity, depend on the material's average particle size and particle size distribution (PSD). Understanding and controlling microstructures in two-phase systems are clearly of widespread technological importance."

Jan 1, 2001

By C. S. Griffith

Lithium Australia NL (ASX:LIT) and ANSTO Minerals have been working together since 2015 on the development of halide accelerated leaching for the extraction of lithium from lithium-bearing micas, spodumene and clays. This technology has been termed SiLeach® process. The driving force behind development of the SiLeach® process, initially, was to develop a hydrometallurgical process to extract lithium from micas and spodumene without the need for the energy intensive, high temperature processing conventionally applied to lithium extraction. This driving force remains today and continues to hold promise in realising the value of previously under-utilised lithium resources. A comprehensive understanding of the technology and its applicability to the processing of micas and spodumene currently exists, and the flowsheet has been rigorously piloted. Production of battery grade lithium carbonate has been demonstrate

By B. J. Jody

Each year, about 11 million tons of metals (ferrous and nonferrous) are recovered in the U.S. from about 10 million discarded automobiles. The recovered metals account for about 75% of the total weight of the discarded vehicles. The balance of the material or shredder residue, which amounts to about 3 million tons annually, is currently landfilled. The residue contains a diversity of potentially recyclable materials, including polyurethane foams, iron oxides, and certain thermoplastics. This paper discusses a process under development at Argonne National Laboratory to separate and recover the recyclable materials from this waste stream. The process consists essentially of two- stages. First, a physical separation is used to recover the foams and the metal oxides, followed by a chemical process to extract certain thermoplastics. The status of the technology is discussed, and the process economics are reviewed.

Jan 1, 1994

By J. R. Goode

There are at least a dozen methods of selectively removing cerium from a mixture of the rare earth elements (REE) including separation techniques based on the oxidation of cerium to the quadrivalent state. Several of the oxidation processes have been operated on a commercial scale, others have been tested and in some cases are part of proposed flowsheets. In this paper, we describe and compare the various methods. We also present preliminary estimates of the costs of early Ce removal and discuss recovery and purity aspects of the options.

By Alicia E. Ares

316 L Stainless Steel samples were solidified directionally under conditions which produced the columnar to equiaxed transition. The position of the transition was located in each sample and the distance from the bottom of the ingot was measured. During solidification the distribution of temperatures were measured by means of thermocouples located strategically. From the measured temperatures the following parameters were derived; the local temperature gradient, the cooling rate and the velocities of the liquid and solidus fronts. Comparing the location of the transition and the values of these parameters it was found that the temperature gradient reaches negative values of as low as -13.44 "C/cm, and velocities of the fronts of around 0.1 cm/s. Also, a supercooling of 5.81°C were measured which was associated with the supercooling for the nucleation and growth of the equiaxed grains ahead of the columnar front. In addition the primary and secondary dendritic spacing was measured in both regions. The spacing was compared with the predictions from available models. The results are presented and discussed in the frame of the results obtained for other alloys

Jan 1, 2002

By A. S. Usrnani

Due to both turbulence and the highly variable geometry of castings, a realistic numerical simulation of the metal flow is prohibitvely expensive with current technology. However, when the chief purpose is to achieve realistic thermal fields a precise How simulation is not necessarily required. In this paper we assume a laminar flow regime and obtain the flow field by solving the incompressible Navier-Stokes Equations using a velocity-pressure segregated semi-implicit finite element method. The free metal surface is predicted by advecting a pseudo-concentration function via the computed How field. This involves an explicit finite element solution of a pure advection equation. The thermal field is calculated by solving the convective-diffusive energy equation by an explicit finite element method using the computed flow field and the location of the free surface. All the advection terms are discretized using a Taylor-Galerkin method. The interface between the metal and mould is modelled using special interface elements. The model is demonstrated by solving practical example problems. The results show that a sharp thermal front is maintained during the course of filling without excessive diffusion. The heat diffusion in the mould can be controlled by varying the metal mould heat transfer coefficient.

Jan 1, 1994

By C. L. Lin

Transformation of linear grade distribution to volumetric grade distribution has been used to estimate the actual mineral liberation during wet, batch, ball mill grinding of a copper ore. The degree of liberation based on the multicomponent-multisize grinding liberation model using volumetric grade is lower than the apparent degree of liberation estimated from using King's linear intercept model.

Jan 1, 1987

By H. Itou, J. M. Toguri, T. Takasu

"Marangoni convection has a large effect on materials processing since it remarkably enhances heat and mass transport near a free interface. To have a better understanding of the behavior of Marangoni convection in molten salts, observation and calculation of the thermal convection in a column held between a pair of Pt disks (2mm in diameter) fixed to hot thermocouples, were carried out.Calculated flow patterns and absolute values of fluid velocity agreed well with the observed results. When the temperatures of both disks were set equal and the height of liquid column was 2.4mm, four vortexes were generated on the longitudinal plane with a typical velocity of 15mm/s . From the calculated isothermal lines, the behavior of the enhanced heat transport was obvious; fluid heated at the disks was conveyed to the free surface and the cooled fluid at the surface was conveyed to the inner region. Increase in the height of column and/or increase in the absolute value of applied temperature difference lead to increase in fluid velocity lineally in this calculation range.IntroductionIn the processing of many materials, fluid flow of melts has a large effect on refining capabilities and on the characteristics of the produced material. Marangoni convection is generated when a spatial gradient of interfacial tension exists on the free interface due to differences in temperature and/or concentration. This promotes heat and mass transfer locally near the interface.For example, Marangoni convection which are created following the dissolution of interfacially active materials, increases the local corrosion rate of refractories (1-3). In absorption and discharge of oxygen and/or nitrogen in a molten metal, the effective reaction rate of the gas components through the gas-liquid interface increases (4-7). Also in crystal growth, the distribution of defects and impurities in the crystal is affected and this can alter its quality (8-11 ). The temperature distribution is also affected and can greatly change the productivity. For these reasons, the effectiveness of Marangoni convection in refining should be quantitatively clarified and its control should be better understood."

Jan 1, 1997

By Malti Goel

"Ferrous and Non-ferrous industry in India is undergoing a transition to meet the growing demand and a new thrust to Research & Development (R&D) is mounting. On one hand, to meet the target laid by the policy in the Iron and Steel sector of 110 million tones production by 2020; on the other, innovations taking place in light metal production technology; both have necessitated greater attention to development of industrial ecological framework. Industrial ecology provides a number of new challenges as well as opportunities for the industry. The development and growth in a particular industry should have a trend towards reduced energy consumption, reduced resource consumption, thereby reducing the cost of production. Technology management strategies will have a key role in achievement of these targets. The paper describes recent developments in technology management, importance of R&D and case studies on adoption of energy efficient & CO2 reduction technologies in metal industry in India. In the end suggestions for future are made.IntroductionInternational Energy Agency [1] has assessed that nearly one third of the World’s energy consumption and 36% of CO2 emissions are attributed to manufacturing industries. In case of ferrous and non-ferrous metals, the resource equality and product quality finally determine the energy share across the countries. In the overall, Iron & Steel industry accounts for about 19% of total industrial energy used. The saving potential for non-ferrous metals is estimated to be anywhere between 13 to 25 % of the energy consumed depending on the level of resource quality. The projections are that energy consumption worldwide in Industry sector would increase 1.8% per annum up to 2030 on average, and up to 2.5% in developing countries."

Jan 1, 2008

By M. J. Bagshaw, J. D. Hunt, R. M. Jordan

"Continuous casting processes, and the roll casting process in particular, offer considerable potential to the Aluminium industry, both meatallurgically and economically.The three major limiting process problems that occur during roll casting are Centre Line Segregation', 'Sticking' where metal adheres to the rolls during casting, and 'Heat Line' formation. 'Heat Lines' are localised semi-continuous longitudinal defects, usually a few cms in width, where the cast metal leaves the roll bite partially molten. These defects occur at relatively low casting speeds when the mean slab exit temperature remains several hundred degrees below the solidus temperature. The objective of the work described here is to develop a better understanding of the roll casting process in general, and in particular, to understand the phenomenon of 'Heat Line' formation.A steady state two dimensional finite difference model has been developed to describe the roll casting process, incorporating a variable heat transfer coefficient through the roll bite. In the model the difference equations are formulated using a control volume method and latent heat is incorporated according to the Scheil equation. A Gauss-Seidel type technique is used to obtain the solution. Because the rate of heat evolution is non-linear the temperature in each box is determined by using a Newton-Raphson method. The solution for a box can be multi valued and therefore lead to instability particularly near the vicinity of the front. A stability 'criterion is presented which shows that to obtain a stable solution it is better to have long narrow boxes rather than boxes with small dimensions in both directions.The model explains why heat lines form in terms of the variable slab/roll heat transfer coefficient.Experimental measurements of slab exit temperatures are also presented. These were obtained on a Hunter twin roll caster for the binary AI-Cu system, at two compositions over as wide a range· of casting speeds as possible. The experimental results are compared with the predicted ones."

Jan 1, 1986

By Mikko Loponen

Outotec has developed an operator training simulator (OTS) platformsuitable for various hydrometallurgical processes. The complete solution is run in the cloud, where virtual client instances can be managed on-demand. The aim is to build a generalizable model that produces coherent results even when operating outside of ideal parameters, allowing the operator to train in unsteady state conditions such as start-up and shutdown. Complex software products are commonly associated with significant development time and cost. Utilizing modular software architecture, only the control system and processmodel are tailored for theOTS,whereas modules such as user administration and cloud-based client machine spawning can be imported, shortening development time. A generic acidic pressure oxidation process (POX) operator training simulation consisting of feed preparation, autoclave, dual-stage flash evaporation and off-gas scrubbing is described. Process is simulated using Outotec HSC Sim 9 process simulator and controlled by Siemens Simatic PCS7 control system.

By R. J. McClincy

The potential techniques for the direct smelting of copper sulfide concentrates to blister copper were evaluated from the standpoint of commercial application. Many existing smelters are adaptable to direct smelting practice but only with improved control of metallurgical performance. Modified and innovative procedures for slag cleaning and metal refining, prerequisites to direct smelting, are presented and discussed. The ability to smelt directly to blister copper using existing equipment and eliminating the need to convert matte offers ,significant advantages to traditional smelting practice from the viewpoint of cost, 'S02 control, and process simplicity.

Jan 1, 1983

By Jr. Foot

The Bureau of Mines, U.S. Department of the Interior, investigated flotation methods for recovering fluorite and byproduct beryllium from the Fish Creek deposit of Nevada. The preferred method includes (l) fluorite rougher and cleaner flotation, (2) de sliming at 20 micrometers, (3) muscovite flotation, (4) silicate flotation, (5) hypochlorite wash of silicate concentrate, and (6) beryllium rougher and cleaner flotation from the silicate concentrate, Laboratory results showed that over 94 pct of. the fluorite was recovered in a concentrate containing 96 pct CaFz. Beryllium flotation produced .concentrates .containing in excess of 5 pct BeO with recoveries over 70 pct. A 1.00-lb/h continuous flotation unit was constructed to demonstrate this procedure,

Jan 1, 1985

By Ying Mao, Zhancheng Guo, Long Ma, Huiqing Tang

"A new 2D computational fluid dynamic (CFD) model was developed for the gaseous reduction of iron ore fines in an innovative reactor-multilayer moving-fluidized bed. The solution of the proposed model was performed by integration of FLUENT and PHOENICS. Numerical results of cold state were compared with the experimental data and the agreement between them was good. A hot case-gaseous reduction of iron ore fines using syngas with this reactor was simulated using the present CFD mode. Results indicate that under the given simulation conditions, total pressure drop is 90 Pa less than that under cold state though the gas supply rate is increased about 4m3 under hot state. Gas temperature decreases from 1073 K at the bottom to 500 K at the top, Utilization efficiency of the gas reduction potential is about 27 %. For ore fines reduction, the final reduction fraction could reach 0. 70 and solid temperature 900 K.IntroductionWith the development of coal gasification technology, various coals could be converted to Syngas with air or steam. Therefore gaseous reduction of iron ore fmes becomes an acceptable alternative process for iron making besides blast furnace route[!] and moreover it still has some advantages in processing low grade iron ore fines[2]. Gaseous reduction using fluidized bed technologies is the most competitive in all direct reduction iron-making processes up to now. It has the advantage that ore fines can be directly charged to the process without prior treatment while its disadvantages are particle agglomeration and high gas/solid ratio[3]. To avoid these advantages, a new reactor, multilayer moving-fluidized bed reactor has been developed for carrying out the gaseous reduction. Hydrodynamic behaviors of gas and fines in the reactor were studied and the results were satisfying[4]. However, due to its unique structure of the multilayer moving-fluidized bed and unique gas-solid flow pattern, models of multiphase flow as IPSA, DPM and Eulerian Model could not give a satisfying solution. The current paper is developed a new CFD model and a new solution approach for simulation of the reactive gas-solid flow in the multilayer moving-fluidized bed for its optimization, design improvement and future scale-up."

Jan 1, 2013