Search Documents

By Raj R. Kallu

Underground gold mines in Nevada are typically hosted in geologic zones with a wide range of geotechnical properties ranging from blocky competent rock to faulted and highly altered soil-like material. Geotechnical engineering design in weak rock utilizes rock mass classification systems as inputs to both empirical and numerical methods. The most common rock mass classification system utilized in the gold mines of Nevada is the easy-to-use Rock Mass Rating (RMR) system; however, in practice it is difficult to apply in weak to very weak rock masses. This paper attempts to improve the sensitivity of RMR in weak rock masses by utilizing W-RMR?a modified procedure for calculating RMR?and evaluates its performance against other methods of determining RMR for predicting in situ moduli. In-situ rock mass moduli were determined using a portable plate loading device (PPLD), and these data were used to quantify the improved sensitivity of the modified RMR versus existing classification systems. The PPLD was designed for performing rapid and economical in-situ deformability tests in a mining environment. Tests were performed at eight sites yielding thirteen rock mass moduli measurements. Statistical analyses indicate Detailed-Discontinuity RMR-89 and W-RMR provide the best correlations to the in-situ moduli compared to other methods of calculating RMR.

Jan 1, 2014

By Asmaa Yassien

Finite element models were developed to study the effect of tensioned and fully-grouted bolts on the stability of the mine opening in a three-entry development system using a typical geological column for the Pittsburgh Coal Seam. The models were used to study the effect of each bolt type on the stress distribution in the immediate roof, yield zone development and the vertical deformations. Comparison of all of those features show that the effect of a tensioned bolt on the stress distribution in the immediate roof is restricted to limited areas, whereas the fully-grouted bolt has a much wider effect on the stress distribution. Both types of bolts can reduce the yielding and deformation in the immediate roof to different degrees. The fully-grouted bolt reduces the sliding along the bedding plane more than the tensioned bolt. Both types of bolts were able to maintain the bedding planes without separation. The induced forces in both types of bolts are analyzed. A rapid increase in the shear force and bending moment occurred in the fully¬grouted bolt due to the relative motion of bedding planes.

Jan 1, 2002

By T. L. Dobecki

As a means of demonstrating the effectiveness of reflection seismology in determining continuity of coal seams, three U. S. field projects are reviewed. The three projects involve coals of varied thickness (2-14m) and age (Pennsylvanian to Eocene) from three coal areas of the U. S. (Pennsylvania, Wyoming, and Washington). Each project also employed its own particular seismic technique, recording system, and seismic energy source although all are considered state-of-the-art, high resolution, digital seismic surveys. Project 1 (thin, Pennsylvania coal) sought detection of sand channels using dynamite and standard in-line (2-D) seismic technique. Project 2 (thick, Wyoming underground coal gasification) involved a gas-explosion (Dinoseis) source with areal (3-D) acquisition methods. Project 3 (thick, Washington underground coal gasification) employed a shotgun-type source and standard in- line methods. Data processing was handled by different contractors for each project. Each project was successful in accomplishing its own particular objective; however, data quality and interpretation seem to be more a function of thickness of the target seam, complexity of the overburden, and processing contractor than a seismic source, acquisition scheme (2-D versus 3-D), or recording instrumentation.

Jan 1, 1981

By Kenneth Rigsby

Black Mountain Resources' Highlands Mine No. I is a full extraction room and pillar operation located in Harlan County, Kentucky. Black Mountain extracts the 0.9 to 1.1 meter (36- to 42-inch) thick Owl Scam that is situated 60 to 70 meters (200 to 235 ft) above the longwall panels of the abandoned Arch No. 37 Mine, in the 3.4 meter (I I ft) thick Harlan Scam. In the areas where full extraction has taken place, the overburden above the Owl Seam ranges from 60 to 430 meters (200 to 1,400 ft). A short room and pillar panel was developed above an extracted longwall panel to test the selected pillar size, to evaluate support systems, and to verify the shape of the subsidence profile over the recovery end of the depleted longwall panel. It is over the recovery end that Highlands Mine No. I would access the Owl Seam reserves that exist above the No. 37 Mine. Black Mountain selected pillars sizes to be employed above the longwalls based on the ability to fully extract a pillar employing extended cuts. After a mechanical testing program was completed and mine behavior and top disturbance were observed in the test panel, John T. Boyd Company (BOYD) verified pillar stability and designed support systems. BOYD previously designed No. 37 Mine's gate pillars and studied subsidence and gob formation over its longwall panels; this effort aided the analysis of overburden movement and pillar integrity at Highlands Mine No. 1.

Jan 1, 2003

By Zhaohui Wang, Jiachen Wang

"Effective surrounding rock control is a prerequisite for realizing safe mining in underground longwall faces. In the past three decades, longwall top-coal caving mining (LTCC) and single pass large height longwall mining (SPLL) found expanded usage in extracting thick coal seams in China. The two mining methods lead to large void space left behind the working face, which increase the difficulty of ground control. Longwall face failure is a common problem in underground mining, which is induced due to low strength and high fracture density of the coal seam. Moreover, the stiffness of main components included in the surrounding rock system also greatly influences longwall face instability. Correspondingly, the surrounding rock system is developed for LTCC and SPLL faces in this paper. Mechanical conditions for simultaneous balance of roof structure and longwall face are put forward by taking the stiffness of coal seam, roof strata, and hydraulic support into account. The safety factor of the longwall face is defined as the ratio between its ultimate bearing capacity and the load imposed on it. The influence of coal strength, stiffness of the coal seam, roof strata, and hydraulic support, as well as the movement of roof structure, are analyzed. Finally, the key elements dominating longwall face stability are identified for improving surrounding rock control effectiveness in LTCC and SPLL faces.INTRODUCTIONThe concentration of coal mining in China is gradually shifting to the west region, and there are a large number of thick coal seams in the newly formed coal mining area. Therefore, the surrounding rock control problems related to mining of thick coal seams will become the focus of research in the field of mining engineering in the future. There are two kinds of mining methods for thick coal seams in China, including single pass large height longwall mining (SPLL) and longwall top-coal caving mining (LTCC). Both methods can accomplish the goal of excavating the full thickness of thick coal seams at one time. SPLL mining benefits from the improvement of the development level of associated equipment. The appearance of large hydraulic supports and high power shearers ensure that the height protected by the hydraulic supports and the height of the sheared coal are the same as the coal thickness. LTCC mining benefits from mining technology advantages. The thick coal seam is divided into two sub-layers, and the working face is normally installed in the bottom layer, while the top coal is caved under the compressive forces due to mining. Therefore, there is a scraper conveyor at the front of the hydraulic support for transporting the sheared coal and another one at the tail for transporting caved top coal. Both SPLL and LTCC methods realize one-off recovery of thick coal seams."

Jan 1, 2018

By Duk-Won Park

A vast majority of the operating longwall sections use shield-type face supports to provide ground control in the United States. As a co-operative research program between the University of Alabama (UA) and Jim Walter Resources, Inc.(JWR), a joint research program is underway to study interaction of shields with surrounding rock masses. A series of analyses on the response of shields are performed using monitored data at a longwall face in a deep coal mine. In this paper, various effects of parameters, such as leg pressure, setting load, developing load, maximum loading rate, pressure in capsule, and convergence between canopy and base, are discussed and recommended as stability indices. A microcomputer program is being developed for instantaneous interpretation of the shield monitored data, and for giving warnings of potential problems. The preliminary results define the effects of the setting load, developing load, and rate of developing load or leg closure rate. The objective of the study is to understand the shield characteristics and their interaction with surrounding strata in real time, then develop a reliable program for maintaining longwall stability.

Jan 1, 1992

By Liane J. Terrill

A 9O) ft (275 meter) section of a highly fractured beam of halite was mined from the roof of a supported thirteen year old drift at the Waste Isolation Pilot Plant (WIPP). The operation was conducted with a continuous miner and allowed the unique opportunity to collect spatial information on roof beam geology and to observe ground support conditions during the mining advance. Photographs and fracture maps of the mining face document the progress of the operation and the deteriorated condition of the strata. This case study details the drift's excavation and support sequences. the geomechanical response, and the conditions found in the exposed roof beam.

Jan 1, 1997

By David K. Ingram

The objective of this U.S. Bureau of Mines (USBM) investigation was to characterize overburden response due to longwall mining. Subsurface strata and surface deformations were monitored at two sites in southeastern Ohio. Site A included two adjacent longwall panels. Site B consisted of one longwall panel. Both sites had similar mine geometries and overburden thicknesses. The major difference between the two sites was the rock strata within the overburden. Multipoint borehole extensometers (MPBX) were employed to measure subsurface displacements. Survey monuments were installed above the centerline and profile of each panel to measure surface deformations. Subsidence of the surface was observed before and after movement was detected in the MPBX units. Initial and final displacement of the MPBX units occurred at the same time at both sites. No deformation was detected outside the panel area. The development of overburden deformation was different over each panel. The final subsurface failure characteristics also varied between panels.

Jan 1, 1994

By Nicholas P. Kripakov

The unpredictable massive collapse of roof in openings developed under apparently safe and stable roof conditions in coal mines of the United States has been of much concern for many years. One type of massive caving phenomenon is often attributed to cutter roof, a failure that initiates at one and/or both upper corners of an entry and propagates nearly vertically resulting in overall failure with little or no warning. This paper reviews current methods being used to control cutter roof and suggests new alternatives. The impact of basic parameters that include mine geometry, overburden geology, rock properties, and in situ stress conditions is discussed in the context of their relationship to this problem. The effects of various stress control measures are investigated with model analysis to gain insight into means of reducing the high level of stress known to exist at the entry corners of a West Virginia coal mine prone to cutter roof. The results are presented in the paper and the feasibility of their practical implementation is discussed.

Jan 1, 1982

By Dale A. Didcoct

Through the combined efforts of the C. S. Bureau of Mines, the coal industry, and Burrell Construction and Supply Company, New Kensington, PA, a steel fiber reinforced concrete crib block to improve coal mine safety in the area of roof control has been developed and is currently in use commercially. The development objective was to improve health and safety conditions with a stiffer, stronger, nonflammable roof support at a competitive cost. During the time this method of roof control has been in use in the mining industry, it has proven to be both functionally and economically effective.

Jan 1, 1982

By Kevin W. Harris

Multiple-seam coal mining is a major issue in underground coal mining that adds additional complexity to the practice of ground control. As reserve exploitation is driven by economics, it is now difficult to mine coal without the existence of previous workings above and/or below the active seam; this is particularly true in the Appalachian coalfields. The frequency in which problematic multiple-seam interactions are now encountered has resulted in significant research regarding the underlying mechanisms of the problems and methods of mitigation. In the last few decades, a great deal has been learned about these interactions and the ability to minimize problems associated with these hazards has greatly advanced, resulting in better economics and improved safety. Minimizing the adverse effects of stress interactions often requires a thorough understanding of site-specific geotechnical parameters and previous mining geometry. This is especially evident in bump-prone ground, where pillar behavior is highly dependent on local conditions. This paper presents a case study in a deep cover, Central Appalachian coal mine where three bump events occurred. Initially, empirical design software was used in an effort to analyze the situation and prevent further instability. The empirical study proved ineffective. A detailed investigation of the bump events using the boundary element software LaModel 3.0 was then performed. This study resulted in a site-specific calibration standard that will be applied in numerical pillar design for the remaining reserve.

Jan 1, 2014

By J. L. Condon

The Bureau of Mines, through in-house and contract research, monitored mountain bump-prone areas of the Olga #2 Mine, near Welch, WV, using microseismic techniques for 15 months during 1985 and 1986. During this period, two ground failures occurred that were considered "mountain bumps" owing to excessive stress buildups. One failure damaged the roof and 4 pillars around an intersection; the second failure, which released much greater energy, resulted in significant damage to over 100 coal pillars. Analysis of the microseismic data collected provided significant insights into the magnitude and location of each failure. The actual failure zone was clearly delineated prior to the mountain bump occurrences through analysis of source locations of each microseismicevent. Trends in cumulative rate plots indicated the onset of structural instability. Although the data could not be analyzed automatically, the significance of the data interpretation cannot be overemphasized. Microseismic monitoring of bump-prone areas can be successful in providing a means to actually observe the structural stability occurring in underground coal mines. This paper discusses data collection techniques, analysis methods, and implications of the monitoring technique, with special emphasis on actual data from two large mountain bumps in West Virginia.

Jan 1, 1987

By Wen H. Su

Multiple seam mining and its associated problems are very serious in Southern West Virginia where poor planning or lack of knowledge in seam interaction often results in complete loss of coal properties. Several measures have been proposed to alleviate the interaction prob¬lems under various multiple seam conditions, but few of them are spec¬ific in terms of mining plan. Two parallel approaches are adopted for this paper. One is field investigation which consists mainly of mine site visits and gathering of data. The other is the two-dimensional finite element simulation of mine workings using the data gathered as input. Two typical cases which represent the past and present multi¬ple seam mining practice in West Virginia were investigated. Much attention is focused on the interaction problems experienced and the important parameters controlling interaction. Several key parameters controlling interaction in multiple seam mining were analyzed. Proper mining plans, by which the interaction problems can be minimized, are proposed for the individual cases after a better understanding of the interaction mechanism was realized through finite element analyses.

Jan 1, 1984

By Jamal Hematian

Understanding the behaviour of rocks in a high horizontal stress field, such as that in Australia, is critical when analysing the stability of underground structures. This paper addresses the significance of the post-failure behaviour of rocks on the stability of underground structures which are under the influence of a high horizontal stress field. The research work was conducted through a combination of numerical modelling, laboratory testing and field investigation. A number of 2-D FE model of roadways were constructed based on the data obtained from laboratory testing and field investigations. The models were then analysed using three different solution techniques; simple linear-elastic, non-linear elastic-plastic and elastic-plastic with consideration of post-failure behaviour (softening model). Results indicated that the post-failure behaviour of rocks significantly influence the stress and displacement patterns around the roadway. The stress and displacement patterns as well as the extent of the yield zone around the roadway predicted by the softening model were in good agreement with that from the field study. Based on the results of the study, an appropriate support system has been suggested to govern the stability of roadways.

Jan 1, 1994

By Syd S. Peng

A total of 209 cases of subsidence data over longwall panels in 16 US coal seems have been collected and built into a subsidence database. The database is developed under MS Windows environment. It uses a very user-friendly menu driven system. The empirical formulae for a number of commonly used subsidence parameters have been derived from those collected subsidence data.

Jan 1, 1995

By David A. Newman

Severe roof control problems have plagued a West Virginia underground mine since its initial development in the late 1970's. Adverse roof conditions in the Eastern portion of the reserve result from a combination of mining: - perpendicular to the major principal horizontal stress direction, - near lineament intersections, - in areas where the ratio of horizontal stress to vertical stress exceeds 2.00 to 4.00, and - where laminated strata are present in the immediate roof. The focus of this study is to identify the engineering (mine orientation, roof safety factor) and geological parameters (lineament and horizontal stress orientation, horizontal to vertical stress ratio, and immediate roof lithology) causing poor roof conditions and to quantify their influence on projected mining conditions in the Western portion of the reserve Rose diagrams were used to illustrate the correlation between the orientation of eight hundred thirty-six (836) roof falls with that of forty-four (44) lineaments and the principal horizontal stress Similarly a composite map was used to demonstrate the relationship between roof falls and the ratio of horizontal stress to vertical stress The immediate roof strata across the property were categorized as either laminated or non-laminated based upon a thorough examination of one hundred sixty-two core logs. The presence or absence of fireclay, a rider coal, and carbonaceous shale was also noted because of the historic correlation with poor roof conditions. Rock strength and physical property tests were conducted on selected immediate roof strata recovered from coreholes drilled along the mains projected to the Western portion of the reserve Potential roof control problems in the Western reserve were quantified based upon the correlations developed by analyzing engineering and geological data The main conclusion is that laminated roof strata, the rider seam, and its associated fireclay will have the greatest influence on mining conditions. Roof problems attributable to horizontal stresses will not be as severe in the West due to an increase in overburden depth and corresponding decrease in the stress ratio. Recommendations are provided for mining orientation, the layout of mains and submains, panel location, and roof support based on intended service life.

Jan 1, 1999

By K. Y. Haramy

This report describes the development of an equation for predicting the crushing strength of 2-inch (5.08-cm) cubes of coal from point load tests made on irregular lumps. The equation was developed from point load and cube crushing strength tests performed on coal samples from six Western U.S. coal seams. For the six coals tested, the means of the point loads [(P)] in kg at failure were approximately proportional to the deans it the distances [(V)], in cm between the platen points for lumps in the 2 to 10-cm size ramie. This finding is at variance with results of tests on other rock types reported in the literature, which tend to show that P is proportional to D2 , as is normally assumed (in theoretical grounds. [The average crushing strength of a 2-inch (5.08 cu) cane for each type of coal was plotted against the log 10 of the slope of the P vs D plots, AP/AID . A straight line was fitted to these plots. The equation of the fitted line is cr = 1.72 x 10 4 10gK -2.10 x 10 4, where Cr is re estimated 2-inch (5. 08-cu,) cube crushing strength of the coal in psi and K is the scope of the straight line fitted to a plat of P v D for the same coal.]

Jan 1, 1982

By Kot F. von Unrug

One of the major difficulties in the proper characterization of rocks surrounding excavations is the lack of data. The existing method for strength determination requires core drilling for sample collection, which, when performed from the surface is costly, and when performed underground, in addition to its cost, interferes with the mine operations. I-landling samples tested in the laboratory is troublesome and also influences the obtained results. Over several years. the author has been interested in developing a method of in situ strength determination that could rapidly generate strength data at low cost without a negative effect on mining activities. The recently developed borehole penetrometer is an improved version of the initial design ( 3 inches in diameter), which was used mainly for strength determination of coal pillars. The new penetrometer has been designed to work in 1.5 inch diameter holes. Such holes can be drilled at low cost with either hand held drilling machines or roof bolters. eliminating limitations of the previous system and opening the possibility of broad application. Strength testing of roof rock around longwall pillars is an example of an obvious benefit when designing secondary roof support. In the paper are given the principles of work of the apparatus and examples of the obtained strength data.

Jan 1, 1998

By Bruce H. Gardner

This paper describes the application procedure of the Stress Control mine design method. This procedure has evolved over the past 20 years of the practice of this Method in trona, potash, salt, and, most recently, in coal mining. The Stress Control Method of mine design has been defined and amply described in previously-published work (1,2,4) -- likewise, the associated system of in situ instrumentation (3,4) and the computer modelling technique (2,3,4) which are the principal tools of this method. The present paper defines the procedure by which the in situ instrumentation and computer modelling cools are combined in adapting the general concepts of Stress Control to produce site-specific design solutions. This procedure is illustrated by means of case examples from three mines. The Stress Control Method utilizes the geometry of underground excavations, particularly through the time sequence of the creation of yielding pillars, to control stresses. The time sequence is devised such that all the primary stress envelopes are transformed into a single secondary stress envelope, surrounding the group of rooms separated by the yielding pillars. The secondary stress envelope provides protection to the roof and floor boundaries from all the external stresses. This stress relief effect removes the cause of roof and floor failure -- high shear stress in the weakly confined boundaries of underground openings. It thereby replaces artificial support with ground self-support, enabling simultaneous in¬creases in stability and percent recovery. Within limits which are still being explored and extended, the Stress Control Method has proven capable of overcoming the trade-off between stability and extraction ratio which has afflicted conventional mining methods. The application procedure of the Stress Control Method is outlined below in terms of the objectives, structure, and stages of a generic mine rock mechanics program for the site-specific adaptation of the time control yield pillar design technique.

Jan 1, 1984

By Jay Hilary Kelley

This paper proposes a modification of longwall roof support to meet new difficult mining conditions that are anticipated in the future. A gob canopy is a movable appendage attached on the rear of a longwall shield to counterbalance the troublesome forward downward force couple (FDFC). The gob canopy can be swung in both vertical and horizontal directions, powered by hydraulic cylinders. Several functions and applications are de- scribed

Jan 1, 1997