Search Documents

By R. K. Steinhorst

Multivariate cluster analysis, MANOVA, canonical analysis, and discriminant analysis of hydrochemistry data were used to investigate the directions of ground water movement in basalts in the vicinity of the Hanford Reservation, Washington. The statistical analyses indicate that the hydrochemistry of the ground waters in these basalt formations is distinctly different on each side of the Columbia River. This suggests that the river is a ground water divide or that the river is roughly coincident with a hydrogeologic barrier boundary. The statistical procedures used in this study constitute a quantitative means for differentiating ground waters according to hydrochemistry.

Jan 1, 1990

By E. F. Schnitzer, S. R. Mamoyac, P. J. Wampler

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion and, in several cases, breaches between the gravel pit and the river. Initial evaluation of several sites that experienced breaches indicates that impacts to the river system are complex and vary significantly from site to site. The impacts to the adjacent river system may be viewed as both positive and negative. Several floodplain-mining sites in Oregon located in areas of historic river flow have reverted to active riverbed. In many cases, state and federal fisheries biologists and university researchers see the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries – Mined Land Reclamation Program (DOGAMI-MLR) is performing additional studies of the impacts to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound floodplain decisions regarding mining.

Jan 1, 1999

By L. Xinghua

Limonite is a general term for a group of amorphous iron oxide and iron hydroxide materials. It is considered as one of the very refractory iron ore types due to its wide variation in chemical composition, iron content, moisture content and easily sliming in the course of comminution. Iron grade of test sample is 25.48%, the iron minerals are mainly limonite; and the gangue minerals consist of quartz and feldspar in majority, secondarily silicate minerals. In this test work, high intensity magnetic separation (HIMS)-cationic reverse flotation and magnetic roasting-low intensity magnetic separation (LIMS) tests were conducted on limonite ore. The test results show that the concentrate with iron grade of 50.97% and recovery of 68.50% can be obtained by HIMS-cationic reverse flotation technique; while using magnetic roasting-LIMS technique, the better concentrate indexes of iron grade of 60.36% and recovery of 89.71% are achieved, and the iron grade of tailing is only 4.42%. Therefore, the magnetic roasting-LIMS technique is a better suitable method for beneficiation of low-grade limonite ore. Keywords: Low-grade limonite; Mineralogy; HIMS; Cationic reverse flotation; Magnetic roasting; LIMS

Feb 27, 2013

By A. Fred Gelding

Introduction In preparing this paper considerable time was spent attempting to find some upbeat data about the mining industry, so those of us in the field could feel somewhat better about future prospects. Much to my regret, I failed to uncover substantial evidence that our near-term or, for that matter, our long-term opportunities appear all that bright in North America. That is certainly not the kind of assessment anyone likes to hear or accept as even a possibility. Those remarks may, on the surface, appear far too pessimistic. This industry will experience a recovery and most likely will see conditions begin to improve later this year or early next. The kind and degree of recovery, however, will more than likely differ from those experienced in the past. Fundamental Changes Clearly, the fundamentals on a world scale of our business have undergone important changes. In recognizing these fundamental changes, mining authorities believe productivity advances are needed to change the direction mining has taken in recent years. The really tough question is whether increases in productivity will be enough to change the course of events that has dominated the mining sector for the past decade. Before one can provide an honest answer, an appraisal of what has and is happening now is necessary. Here are some changes and events that have taken place that effect domestic mining and will probably continue: • Mineral-rich lesser developed countries (LDCs) in Africa, South America, and Asia-Pacific have reached a point where they have developed the needed mining infrastructure to not only produce at a high rate, but in many instances, at a lower cost than fully developed countries. Just as importantly, these countries, even if they do not enjoy lower costs, will produce for world export with government subsidies because min¬ing products are key in obtaining badly needed foreign exchange. • These producing countries also have the distance advantage of lower labor, environmental, and other important regulatory costs. If that were not enough, these same countries have minerals with considerably higher grade ore and, in some cases, much lower cost accessibility. • Exporting North American commodities is impaired by a dollar that continues to strengthen against other important currencies around the world. There are other impediments to overcome, but these represent some of the realities our industry faces. Can those obstacles be overcome through improving productivity? In the past, this industry has offset the impact of these events to a sizeable degree through innovations of mining techniques, equipment and processes, and by increasing the size of its individual operations to reduce costs. Will further enhancements along these lines be enough to alter this changing balance in the future? While there is no answer, it is apparent that if we do not mount a full-scale assault in some key areas, our prospects will not be encouraging. Productivity improvements throughout the entire chain of the mining industry most certainly rates as a high priority. Every link in that chain from mine planning, equipment selections, and transportation considerations needs to be examined and reexamined to assure the lowest effective cost is developed. Quality, while oftentimes costing a little more initially, is still the most cost effective purchasing decision to make. Regulations Another area of concern is regulations, be they environmental or those that dictate what must or must not be done in running our business. Certainly, I do not suggest that we not protect our environment. However, there is an acceptable balance that has, over

Jan 11, 1983

By Charles H. Wells

This paper describes a commercial installation of a sophisticated instrumentation and control system designed to maximize the performance of heavy medium cyclones. Samples of plant feed and its products were collected and analyzed for ash content so that measures of efficiency could be determined for plant operation under (1) manual control and (2) automatic (computer) control. The heavy medium cyclone control strategy and its digital computer implementation are discussed in detail. The sample results are analyzed and the economic benefits of automatic control are discussed. Results from the initial data sets quantify the economic benefits of automatic closed-loop control; viz, increased recovery and reduced clean coal variability have been clearly demonstrated.

Jan 1, 1981

By E. F. Schnitzer, P. J. Wampler

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion and, in several cases, breaches between the gravel pit and the river. Initial evaluation of several sites that experienced breaches indicates that impacts to the river system are complex and vary significantly from site to site. The impacts to the adjacent river system may be viewed as both positive and negative. Several floodplain-mining sites in Oregon located in areas of historic river flow have reverted to active riverbed. In many cases, state and federal fisheries biologists and university researchers see the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries – Mined Land Reclamation Program (DOGAMI-MLR) is performing additional studies of the impacts to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound floodplain decisions regarding mining.

Jan 1, 1999

By Tania Schmid, Marco Portal Valdivia, Sandra Nowosad

Today’s mining industry faces rapid transformation driven by automation, climate responsibility, and ESG demands, requiring more than technical expertise. Future mining engineers must blend engineering excellence with key human skills such as communication, leadership, resilience, empathy, adaptation to change, curiosity and lifelong learning. Based on two recent surveys, one to senior leaders with over ten years of experience in the mining industry and a second, focused on understanding the perceptions of young professionals, this paper explores which skills become core competencies by 2030 for navigating complexity, leading responsibly, and enabling sustainable transformation. Furthermore, it also examines how educational institutions can adopt strategies to foster the development of these critical skills, preparing future mining talent for evolving challenges.

Feb 22, 2026

Start with your assessment of the minerals business —domestic mining as well as operational and consulting perspectives. As a third generation miner, I have been living the mining business for as long as I can remember. I have watched commodity prices produce boom and bust cycles in places like Price, Utah (coal), Douglas, Arizona (copper) and Eureka, Nevada (gold). It is unsettling to see how our industry has fluctuated, but it always seems to rebound if you can stick out the down cycles. However, our most recent dip in the cycle was, in my opinion, characteristically and permanently different. In the past, when prices went south, people hunkered down and waited out the cycle until things came back, much the same as they had every other time. Not this time. This time, we saw a consolidation of the industry in proportions never seen before. Mega-mergers like Exxon-Mobil, Phelps Dodge-Cyprus and Newmont-Normandy have changed the complexion of our industry forever. And that is true not just of the mining companies; it happened across the supporting business lines as well. As a midsized niche engineering and environmental service provider to the mining industry, companies like mine are few and far between these days. The lean cycle saw many of the small and midsized providers get gobbled up by consulting giants like URS and TetraTech. The mentality of a mega-company, whether a commodity producer or a goods or service provider, is different than that of their small- and medium-sized counterparts.

Jan 1, 2005

By P. Lopez, E. Wellman, N. Risso, A. Anani

Current machine learning models used for roof fall hazard prediction are mounted on expensive sensors, computationally expensive, or lack the robustness for accurate prediction in the underground mining environment. This research aims to provide a design methodology for a robust, low-cost, deep learning-based algorithm for underground mine roof fall hazard prediction. A data sampling plan is developed to ensure the replicability and robustness of the developed model. In addition, feature engineering and transformation methods are described to identify relevant features for hazard identification. The methodology described here will be used in model development, tested, and implemented as a real-time mobile device application. The new tool will be expected to detect roof fall hazards in real-time and contribute to a crowdsourcing approach for underground hazard detection.

Feb 1, 2023

By V. A. Leach, J. R. Johnson

The calculation of the dose to the bronchial epithelium, lungs and other body tissues from exposures to airborne radon and thoron daughters requires a knowledge of the pattern of deposition in the respiratory system and clearance from it. Exposure to radon or thoron daughters is measured in units of Working Level Months (WLM), which is independent of the aerosol particle size, the fraction of daughters that are attached to the aerosol and the degree of disequilibria between the daughters, and age and breathing rate of the subject. These factors will influence the deposition and clearance, and hence dose. It is therefore of interest to find the relationship between WLM and calculated dose as a function of aerosol size, unattached fraction, and disequilibria, and of age and breathing rate, and to define ranges for these parameters for which WLM is an acceptable measure of the risk. This presentation briefly reviews the two dosimetry models being considered by a current Nuclear Energy Agency (OECD) Working Group, and using these models, defines limits on parameters for which the WLM is applicable.

Jan 1, 1981

By Russel Delmar

Construction of Ontario Power Generation?s 12.8-m diameter, 10.4-km long water diversion tunnel in Niagara Falls, Ontario, is underway. The tunnel is being excavated by means of a 14.44-m diameter open gripper Tunnel Boring Machine. The tunnel lining is constructed as a two-pass system with the initial lining consisting of rock bolts, mesh, steel channels or ribs, and shotcrete, and the final lining consisting of pre-stressed cast-in-place concrete with a waterproof membrane. This paper describes salient design and construction aspects as follows: ? Regional and Site Geology ? Tunnel Layout and Design ? TBM Tunnelling and Cast-in-place Concrete Lining Construction

Jan 1, 2008

By M. N. Nabighian

Utilization of x-ray diffraction data for mineral identification has been well documented and accepted as an analytical tool in industrial and research organizations. However, the search for new methods to minimize errors affecting measured reflection intensities is being carried out by all concerned. Recent application of computer capability has greatly reduced the time required in handling data for mineral analysis and has increased the capability of accepting more data for greater precision. The purpose of this communication is (1) to describe the concept of cross-power in XRD analysis, and (2) to show that direct comparison analysis for multiphase systems has improved analytical accuracy when all available x-ray diffraction data are used in conjunction with high speed data processing by computer.

Jan 1, 1972

By Vojtech Gall

Pre-support measures for urban tunneling have seen a substantial development in the recent past. Ground improvement techniques, pipe-arch and spiling methods now allow for non-disruptive tunneling at very shallow depths under sensitive structures, rail tracks and roadways. The paper presents experience gained on national and international projects built over the past decade that represent case histories and therefore may be used as guidance for the development of similar solutions for future tunneling projects at shallow depths. Reference projects include tunnels for the Washington, DC Metro, London Underground, Dulles Inter-national Airport, Busway tunnels in Boston and the Ft. Canning Tunnel in Singapore.

Jan 1, 2008

By J. Finch, R. McIvor

This paper presents the development of a new grinding circuit steady-state modeling system. It is fundamentally based on the “functional performance equation”, which has now been used to improve the performance of numerous grinding circuits. This equation characterizes the two distinct efficiencies that are at work in a ball milling circuit, and how these relate to overall circuit productivity. It does so based on the particle size chosen to distinguish between coarse and fine (product size) material. Now, by applying it to all the material size classes, a simple yet reliable ball mill model was created. Combined with cyclone recoveries, the complete, detailed grinding circuit performance can be exactly reproduced mathematically by the computer program. It can then be used with separate process equipment application engineering methods to systematically engineer grinding circuit improvements. The development, features, uses and limitations of the system are described.

Jan 1, 2007

By Raymond W. Henn

The 32nd annual short course ?Grouting Fundamentals and Current Practice? was held at the Colorado School of Mines, June 13-17, 2011. The field demonstration portion of the course was conducted June 16 at Baski Inc.?s yard in Denver, CO. The full-scale field demonstration presents many types of drilling and grouting equipment in operation as well as numerous grouting methods per-formed under various field conditions. As part of the field demonstration, the class was shown the proportioning, mixing, testing and injection of various cement grout mixes into sand columns under controlled and recorded conditions. These sand column demonstrations have been conducted under controlled and measured conditions each year since 1999 as part of the short course. The sand column demonstrations were conducted prior to 1999, but with less quality control and minimal record keeping of the proportioning, mixing, testing, injection pressures and the final permeation results.

Jan 1, 2011

By P. Creevy, P. F. Mousset-Jones, G. Danko, A. D. S. Gillies

The surface heat transfer coefficient is measure of the rate of heat transfer from exposed rock surfaces to the ventilating air. Knowledge of its value is of particular importance to accurately simulate the early stages of rock cooling after the opening of an excavation. A number of theoretical formulae for the calculation of the coefficient are available for use in mine climate simulation. However, direct determination by in situ measurement is preferred. Instrumentation, which has been developed for in situ mine measurement, and experimental procedures involving measurement at varying air velocities, are described. In a major study covering four Australian underground mines, the system has been used to determine surface heat transfer coefficients. A direct relationship was clearly established between the measured surface heat transfer coefficient and air velocity. Comparison is made between experimental results and those previously measured or calculated by others. The relationship established can be described by an equation and holds for air velocities above 0.4 mls. The derived relationship was con- firmed at all mines tested and is independent of geology and tunnel dimensions found in modern mines.

Jan 1, 1991

Extending an organization?s knowledge base throughout the entire enterprise can improve operations. Until recently, though, field operations were often left out of the information loop, as extending high-bandwidth communications into harsh environments often proved impossible due to thermal extremes, physical hazards and caustic chemicals. However, advances in the design and manufacture of rugged fiberoptic cables have now enabled the successful installation of 10-gigabit transmission links to places such as mining operations. The experience of Consol Energy exemplifies how plant managers can successfully enlist ruggedized tight buffered cables to help carry the efficiency of ERP communications into even the most challenging work environments. ?As part of our ERP implementation, we extended our corporate network underground into our mines using fi beroptic cable,? said Tom Prokop, manager-site support for Consol Energy. ?We?ve actually had rooffalls bury the cable between rocks and still did not lose data communications. Our maintenance personnel are now able to access our ERP system while underground at locations that can be up to 32 km (20 miles) away from their desks or the warehouse. Access to the corporate network allows them to order parts, look at electronic schematics, access monitoring data, no matter where they are in the mine. With a few hundred workers below ground, this immediate access translates into a time-savings that adds up in a hurry.?

Jan 1, 2009

By S. Todd Mickleborough

The geostatistical technique of conditional simulation is applied to measure the uncertainty in factor of safety predictions for soil slopes where there is incomplete knowledge of the spatial distribution of soil properties. A case study considers a natural clay slope in Canada. The sequential indicator simulation technique is used as a means for generating a series of spatial maps of soil properties for this site. These maps approximate random draws from the conditional probability density function that characterizes existing uncertainty in the spatial distribution. Factor of safety determinations are then made for each simulated map using the simplified-Janbu approach, where the computations are performed with a new computer program that can operate on irregular spatial profiles of soil properties specified on a discrete grid. A unique capability of this approach is the ability to generate the distribution of factor of safety conditional to the type, position, and value of existing site characterization measurements. This capability should reduce uncertainty in FS predictions.

Jan 1, 1993

By T. W. Camm, J. C. Johnson, S. D. Rosenthal

"Most engineers are bright, hard-working, reliable and prefer to avoid conflict. An engineering curriculum tends to self-select these characteristics. By most standards, you would expect workers exhibiting these traits to require minimal supervision. But, is this true? Is this how most current engineering managers lead? Looking at some current theories on leadership combined with personal anecdotes, this article will look at some common misconceptions about leading engineers.Engineers are different. There, it has been said. From cartoons to movies to television shows and more, there is a reason stereotypes of engineers resonate. Yes, you can find a lot of individual variation among specific engineers that you may know, but they do not detract from some of the overarching commonalities that engineers are known for.Clash of culturesWhat distinguishes a professional? Raelin (1985), in his book Clash of Cultures, describes professionals as having superior intellectual training, maintaining their own standards of excellence and being supported by associations that maintain the quality of the profession. Engineers obviously fit all three of these ideas: an engineering degree is still regarded as one of the most difficult to attain. Standards are maintained both through peer review and in academia, through ABET accreditation and through professional associations like SME to promote the discipline and foster technical growth.Six characteristics representing professional status are described by Raelin (1985, p. 9):• Expertise — prolonged specialized training in a body of abstract knowledge.• Autonomy — the freedom to choose the means to solve a problem.• Commitment — primary interest is in pursuing the practice of one’s own chosen specialty.• Identification — identifying with the profession and with fellow professionals, both through formal associations and through peers external to the organization.• Ethics — providing service without concern for oneself or without becoming emotionally involved with the client.• Standards — committed to help in policing the conduct of fellow professionals."

Jan 1, 2018

By S. F. Diehl

Drill cores from uranium roll-front deposits, hosted in lower Cretaceous strata, were examined from the proposed Dewey Burdock in-situ uranium recovery site in the northern part of the Edgemont uranium district, South Dakota. Uraninite (UO2), coffinite U(SiO4)0.9(OH)0.4, and doloresite (H8V6O16) occur as pore-occluding cements within the Fall River Formation in the Dewey area. In contrast, within the Lakota Formation in the Burdock area, uranium (with very little vanadium) is absorbed onto woody fragments and amorphous carbonaceous material in pressure-solution seams. Both areas have typical uranium roll-front mineralogy with 0.5 wt. % pyrite in the reduced solid phase and no pyrite in the oxidized solid phase. The groundwater at the ore zone is not oxygenated, so the uranium is relatively insoluble. Uranium in solution in ground waters is <10µg/L at Dewey and <22 µg/L at Burdock. Micromineralogic and geochemical data are being used to understand water/rock interactions, uranium distribution and movement, and as input factors for predictive reactive transport models.

Feb 27, 2013