Search Documents

By T. Nesane, S. S. Mnyakeni-Moleele, L. C. Murulana

The effectiveness of two synthesized ionic liquids, 1-(benzyloxy)-1-oxopropan-2-aminium 4-methylbenzenesulfonate (1-BOPAMS) and 4-(benzyloxy)-4-oxobutan-1-aminium 4-methylbenzenesulfonate (4-BOBAMS), were evaluated for mild steel corrosion inhibition in 1.0 M hydro-chloric acid solution, using electrochemical impedance spectroscopy (EIS), potentiodynamic polarization (PDP), and gravimetric techniques. Organic moieties responsible for the adsorption process on mild steel surface were investigated using Fourier transform infrared spectroscopy (FTIR). Gravimetric analysis revealed that the inhibition efficiency of 1-BOPAMS and 4-BOBAMS increased with concentration, with maximum inhibition values of 90.32% and 97.91%, respectively, at the highest concentration of the inhibitors. Gibbs free energy (ΔG°ads) values indicated a strong interaction between the mild steel surface and the molecules of the ionic liquids, and that the adsorption process was spontaneous. These values also show that the inhibitive nature of ionic liquids against mild steel corrosion is caused by a mixedtype of adsorption film formed on the steel surface. The Langmuir adsorption isotherm was used to describe the adsorption of ionic liquid molecules onto the mild steel surface. Polarization curves showed that 1-BOPAMS and 4-BOBAMS have a similar effect on both the anodic and cathodic half-reactions, indicating that they prevent the dissolution of mild steel through both physical and chemical process. Nyquist plots were defined by incomplete semicircle capacitive loops, showing that the charge transfer mechanism controls the corrosion of mild steel in acidic solution.

Apr 1, 2021

By I. M. Wolf, S. A. Usmar, L. A. Cornish

The limiting criterion in the use of stainless steel for certain forming operations such as coining is its hardness, which determines parameters such as required striking pressure, wear on dies, and integrity of pattern detail. Attention is given here to the development of ultra-soft ferritic stainless steels for coinage. In the first instance, the influence of carbon content on the striking properties of a series of commercial and experimental 17%Cr alloys was evaluated. It was found that a lower carbon content permitted the striking of relatively highly profiled and intricate patterns, provided that the hardness did not exceed 125 HV. Hardnesses as low as 115 HV were achieved in the fully annealed condition, but these alloys required high striking pressures. In a further study, three grades of experimental 14%Cr ferritic stainless steels were produced with a view to optimizing the ductility. When the residual impurities were minimized, hardness values of about 100 HV and lower were achieved. Micro-alloying additions allowed the heat-treatment response and grain size to be controlled. Excellent tensile properties, with elongations of up to 42 per cent, were achieved in the fuly annealed condition, and highly profiled patterns were produced in coining trials.

Jan 1, 1993

By F. K. Crundwell

The rate of dissolution of sulphide minerals is frequently interpreted in terms of the passivating behaviour of a layer of material on the surface. This interpretation has driven research to identify and possibly remove this layer from the surface, and thus yield higher rates of dissolution. The identification of such layers has proved difficult, with different researchers claiming different compositions for possible layers. An alternative framework has been pursued by the author and co-workers, who have argued that the rate of dissolution is governed by the electronic structure of the minerals which give rise to their semiconducting properties. Researchers sceptical of this approach have argued that semiconducting properties are only important in highly pure substances. In this paper, we review the electronic and semiconducting properties and discuss how they impact dissolution behaviour. These properties affect their colour and dissolution properties even though the minerals are not high purity substances. Keywords: Dissolution, leaching, passivation, semiconductor, chalcopyrite

Jan 1, 2020

By N. de Koker, Y Jooste, J. Gerber

This paper presents a novel application of the boundary element method for numerical modelling of the seismic activity and hazard that is associated with the shaft pillar extraction at Bambanani mine in South Africa. In the numerical model, the tabular mining excavations are represented by displacement discontinuity elements, and to accommodate crush, shear, and fault slip seismic events, the numerical model is populated with additional displacement discontinuity elements that represent modelled crush- and shear-type failures in the rockmass. Crush-type failures are evaluated by applying the limit equilibrium method and a Hoek-Brown strength criterion, and shear-type failures are evaluated by applying a Coulomb-friction strength criteria to Ortleppshear and geological features. In this paper, the modelling results are presented as time history analyses of modelled potency from 1 January 2010 to 30 June 2022 and normalised exceedance rates for different mining periods using an upper-truncated power law. The normalised exceedance rates of seismic events that have moment magnitude Mw ≥ 1.0 are lowest for the initial mining period (26 events per year) and highest for the final mining period (218 events per year). The relative errors of the modelled potency and normalised exceedance rates are typically less than 10% or 15%, which suggests that the modelling methodology is appropriate for medium- and longer-term forecasting of seismic activity and hazard, as presented in this paper. Shorter-term forecasting is not considered in this paper.

Nov 24, 2025

By J. E. Dickinson, R. Campbell, M. J. Cole, K. P. Galvin, M. C. Cole

It is common practice in the beneficiation of iron ore ultrafines to apply reverse flotation, and hence float the gangue minerals, leaving behind a high-grade iron ore product. Given the difficulty in floating particles finer than 20 μm, especially those finer than 10 μm, it is necessary to subject the feed to desliming ahead of flotation. There are two problems with this approach. Firstly, given the known inefficiencies of cyclones, desliming needs to be aggressively applied to particle sizes upwards of 45 μm to ensure all the offending ultrafine gangue is removed. Secondly, desliming also removes a significant portion of the valuable iron ore. Thus, a significant portion of the ultrafines, including the iron ore, is lost to the tailings. This paper examines the direct flotation of iron ore fines using the Reflux Flotation Cell. The RFC operates using a concentrated bubbly zone, in the absence of a conventional froth zone, for delivering strong counter current washing through an inverted fluidised bed of bubbles ahead of the product discharge. A system of parallel inclined channels in the lower part of the cell provides enhanced segregation of the bubbles from the tailings, preventing the loss of air bubbles into the tailings. Experiments conducted under semi-batch conditions produced encouraging results with concentrates of ~65% Fe grade in a single flotation stage. Comparatively, up to five successive batch flotation stages were required when using a laboratory scale batch mechanical flotation cell to achieve similar Fe grades. For a given grade, lower Fe recoveries were typically achieved by the RFC. This was attributed to the effective prevention of ultrafine particles succumbing to hydraulic entrainment under a positive bias flux, as well as an increasing feed volume involved in the semi-batch operation using inverted fluidisation water for cleaning. Overall, similar grade-recovery curves were produced, however, significantly higher grades were obtained by the RFC and with fewer separation stages. Keywords: Desliming flotation, iron ore, modified release analysis, reflux flotation cell

Jan 1, 2020

By M. de Beer

The conversion of carbon-containing feedstock into liquid fuels can proceed via the Fischer-Tropsch synthesis, which is catalysed using supported cobalt catalysts. These catalysts contain noble metals to facilitate the reduction of oxidic cobalt species in the catalyst precursor to metallic cobalt, which is the catalytically active species for the Fischer-Tropsch synthesis. This is thought to occur via hydrogen spillover, i.e. the diffusion of atomic hydrogen over the support from the noble metal to the oxidic cobalt moieties. Noble metals may also affectthe dispersion of cobalt in the active Fischer-Tropsch catalyst. The economic aspect of the addition of noble metals to the Fischer-Tropsch catalyst is discussed.

Jan 1, 2014

By J. A. Theron

"This paper provides guidelines on performing mass and energy balance modelling involving coal and coal derivatives. Usually, the inputs to a pyrometallurgical process would be specified in terms of elements and compounds. Reliable thermochemical data is more widely available for species involving uniquely defined, relatively smaller molecules. However, in the case of coal, the molecules are extremely large and not uniquely defined. Consequently, modelling processes involving coal and its derivatives have several potential pitfalls. These are outlined in the present paper. The main findings are as follows:•,Coal proximate analysis should not be regarded as absolute; it could vary with several parameters, including heating rate •,For modelling, the use of ultimate analyses should be considered a preferable option to proximate analyses, where, ‘fixed carbon’ and ‘volatiles’ are not defined in terms of chemical composition •,Significant errors could be made if the larger molecules are neglected during calculation of the calorific value (CV) of coal gas (the gas liberated when coal is heated in the absence of oxygen) •,For elemental analyses, the oxygen content (which is calculated by balance) should be checked to ensure it is within the expected range •,For representation of sulphur in coal, double-counting due to SO3 in the ash analysis should be avoided •,Potentially, oxygen in coal could be represented as O2, H2O, CO, or CO2; however, use of some of these species without considering the experimentally determined gross CV results in significant errors in the energy balance. If coal enthalpy is calculated from elemental analyses without correction, representation of coal oxygen as H2O(l) gives reasonable accuracy (up to 6.9% error for a set of South African coals). Coal volatiles could be represented by a complex mixture of compounds, even using different oxygen-containing species than the abovementioned four, provided the enthalpy is corrected •,It is recommended that an ‘enthalpy correction value’ is incorporated in energy balances involving combustion, devolatilization, or conversion of coal and coal derivatives, e.g. coke, char, or tar. That would imply that proximate analysis, elemental analysis, as well as the gross CV would be required for all solid or liquid coal-derived substances being modelled. No other correction due to the form of carbon being different than graphite should be used, as that would imply doublecounting some effects."

Jan 1, 2014

By A. McQuillan, N. Bar

Geotechnical models developed during the planning stages of open pit mines are three-dimensional so as to capture the spatial variation in lithological, structural, hydrogeological, and geomechanical conditions. Geological models that describe the lithological and structural (faulting and folding) characteristics of a deposit are always 3D. Likewise, boreholes and piezometers used to develop geomechanical properties and groundwater models are drilled at spatial offsets across the deposit to understand the lateral and vertical characteristics. Yet when geotechnical analysis is completed, often the three-dimensional geological, hydrogeological, and structural models as well as geometrically complex 3D mine designs for optimizing economic mineral recovery and overburden removal are simplified to two-dimensional sections. In this paper we demonstrate that this simplification can lead to the wrong failure mechanism being identified, analysed, and/or a conservative factor of safety being calculated and hence an over-estimation of slope stability. Through case studies we show how three-dimensional analysis methods are more suited to rock slopes, particularly those with anisotropic material strength, when singularities such as geological faults are present, and nonlinear slope geometry. When the same slopes are analysed in two dimensions, the failure mechanism calculated is often fundamentally incorrect. The case studies further reveal that the factor of safety calculated in three dimensions is not always higher than the two-dimensional factor of safety.

Feb 6, 2023

By L Tolmay, L Nair

Investor confidence can be compromised when one observes large discrepancies between the SAMREC reserves and the mining plan. It is therefore up to the responsible persons to ensure that all contributing factors get taken into account when determining a reserve declaration. Confounding factors could be further aggravated by large oscillations in the commodity price thus resulting in major changes to the mining plan, if the accepted price was either too optimistic or pessimistic. Additional factors that must receive our attention are, uncertainty in geological facies type, mining practices, geology and grade estimation. The paper outlines (in the authors? opinion) some of the important factors that need to be taken into account, in order to ensure proper alignment between the estimates of the life of mine (LOM) reserve grades, and the corresponding actualisation of the mining plan. These parameters provide an historical insight into what actually happens when attempts are made to implement the mining envisaged in the LOM plan. In turn these allow judicious application of discount factors that enable a realistic estimate of SAMREC reserve classification and declaration. Some of the factors that will be covered are: - 1) Flexibility of developed reserves and the ability to maintain this. 2) Mining control mechanisms and their overall efficacy. 3) The ability to extrapolate facies types and its effect on grade control. 4) The ability to control the mining mix and value variation. 5) Finding a happy medium between optimism and pragmatism.

Jan 1, 2007

"This paper challenges the traditional notion that mine planners need to plan production so as to incur the lowest mining cost. For a given mine configuration, a mine that increases its mining rate will incur increased mining costs. In an environment in which operations are fixated on cost reduction, a proposal that increases costs will not be readily accepted. Such a proposal requires financial justification—the increase in costs might be recuperated by the additional production. This paper evaluates the net present value (NPV) across a range of copper prices for two underground orebodies located at different depths, using a production rate of 300 kt per quarter and a scenario that introduces additional equipment and costs for 450 kt per quarter. The evaluation was based on the changes of NPV for the orebody located at a shallow depth compared with the orebody at a greater depth. Discrete event simulation combined with mixed integer programming was used for analysis. Unlike traditional sensitivity analysis, this study re-optimizes the mine plan for each commodity price at each production rate. The results show that, for the low mining rate at the final copper price, an NPV of A$1530.64 million is achieved, whereas an NPV of A$1537.59 million is achieved at a higher mining rate. Even though pushing mining rates beyond traditional limits may increase mining costs, this option may be beneficial at certain commodity prices, particularly when prices are elevated. IntroductionA traditional notion among mine planners is that mining rates should be planned in such a way as to reduce production costs. This concept generally relates to the mining rate that results in the highest machine utilization for the selected equipment. Although an existing mine may consider increasing its mining rate by adding equipment to a given mine configuration, this typically increases mining costs. In an environment in which operations are fixated on cost reduction, a proposal to increase costs may be very difficult to argue for. The value of the mine plan is well recognized as varying with the mining rate for a given orebody (Smith, 1997)"

Jan 1, 2017

By D. N. Golenkov, N. I. Lomaka, A. V. Kozub, T. V. Ignatova, E. V. Shelepov, D. O. Sharkovskiy, A. V. Chanturiya, R. I. Ismagilov

The modern Russian iron ore mining industry is faced with multiple challenges from everincreasing requirements of steel-making, the value of iron ore concentrates, depletion of high-grade ore reserves and complications of the mining and geologic environment’s necessity to process low-grade ores with complex material composition and low valuable mineral content; with finely disseminated aggregates of metal and non-metal minerals responding similarly to processing. The upgrade of the existing operations’ fine wet screening was implemented by Metalloinvest; as well as the design of a process flowsheet for concentration oxide ferruginous quartzites with low concentrating ability. The scientific basis for improvement of low grade ore concentrating efficiency and the upgrade of market product quality is supported by an in-depth study of ore characteristics, application of high performance equipment for separation of fine-grained mineral aggregates and use of depressor selective to ferruginous minerals in the flotation process. The benefits of wet fine screening have been proven by industrial scale tests; as well as the feasibility of significant upgrades in product quality which have been confirmed as a result of the tests. A road-map for the upgrade of an existing process for the concentration of unoxidised ferruginous quartzites deposited in the Mikhailovskoye ore field was developed, based on the industrial scale test of a fine screening process. With reference to the ability for concentration, three major ore types oxidised ferruginous quartzites were defined as a result of comprehensive geological mapping and process sampling: oxidised ferruginous quartzites with good concentrating ability: over Fe67% grade of concentrate with ca. 80% iron recovery; oxidised ferruginous quartzites with moderate concentrating ability: Fe65-67% grade of concentrate with 70-72% iron recovery oxidised ferruginous quartzites with low concentrating ability: below Fe60% grade of concentrate (cannot be processed into desired grade market product). A process flow diagram combining magnetic separation and flotation has been designed and recommended for implementation based on the in-depth research of defined Mikhailovskoye deposit iron oxide types, including grain size, chemistry, petrographic, mineralogy, hematite and magnetite grain size distribution and liberation analysis.

Jan 1, 2020

By Maggi Loubser

"In a technologically advanced era, where process control is accurately maintained within the smallest error margins, and accuracy and precision are continuously improved, sampling is still left to the lowest paid employee in the company without training him or her properly to understand the relevance and importance of the task. In this paper the objectives of sampling in a process control environment is discussed and an attempt is made to link it to the theory of sampling. Some of the practical problems associated with implementing theoretical sampling principles in an industrial environment will be elucidated and some examples given on how compromises are made. Different methods of sampling will be discussed with real life examples from different manufacturing industries."

Jan 1, 2014

By I. Silin, H. Wotruba, A. Liono, I. Volobayev, Y. Rubinstein, D. Gürsel

Old, abandoned or in situ processed and storaged tailings can be a potential source of remained valuable metals and minerals. By reprocessing of tailings, it is possible not only to achieve economical profit from recovery of valuable metals, but also to reduce environmental damage caused by tailings such as generation of acid mine drainage from sulfide minerals, mobilization of heavy metals, soils and groundwater contamination. In addition, storage facilities can be successfully redesigned with modern geotechnical requirements and monitoring to avoid a dam collapse of abandoned tailings. In this case study, the processing of low grade abandoned tailings was investigated. Copper (0.15%), cobalt (0.032%) and gold (0.35 ppm) were determined as main valuable and recoverable metals. Cobalt occurs as cobaltite and cobaltiferrous pyrite, while chalcopyrite represents copper. The fine fraction of tailings below 32 μm is enriched with cobalt and copper. Preliminary test-works with initial tailings sample were aimed to recover copper, cobalt and gold. The previously tested magnetic and gravity separation could not recover the metals in a pre-concentration step. Flotation tests of the tailings sample had shown a suitability for flotation without previous regrinding of the tailings. The valuable minerals are first proposed to be recovered by collective flotation, followed by a selective circuit with production of a low grade copper concentrate and a cobalt bearing pyrite concentrate. Based on various tested collectors, amounts of sulfidisation agents and activators, a suitable reagents regime was determined and used for up-scaling by locked cycled test. Keywords: reprocessing, tailings, copper, cobalt, gold, flotation, cobaltite, cobaltiferrous pyrite

Jan 1, 2020

By S. Dessureault

Computer Integrated Mining (CIMG) is a process of using computer networks to transform islands of enabling technologies into a highly interconnected mining system. CIMG involves the integration of advanced technologies at various levels in the mine business to achieve higher flexibility, better quality of processes and control, and improved profitability. Justifying the benefits of CIMG are difficult as many of the advantages are derived from improved flexibility, quality, and control. Justification is based on the evaluation of the benefits to be gained, compared to the required capital investment. Management tools used in mining are currently inadequate in assessing the value of advanced technology whose benefits are primarily qualitative. A key aspect of successful implementation is management acceptance, which has to be won through the capability to justify the technology's financial costs and the true value of all of its benefits. The manufacturing industry faced similar justification difficulties when adopting advanced technology in factories. A significant amount of funding and research was invested into developing management strategies and approaches to justification. Many of the problems that faced the transformation of the manufacturing industry in the late eighties and early nineties are now facing mining. The solutions derived for manufacturing may help mining in its transition to an increased reliance on integration technology. Reviewing the industrial history of computer integrated manufacturing identifies several tools and strategic frameworks that can be adapted for mining. Keywords: Computer integrated mining, justification techniques, CIM, information technology.

Jan 1, 2003

By D.W. Gentry

1. Book reviews Mine investment analysis, by D.W. Gentry and T.J. O'Neil. Society of Mining Engineers (Caler No. D, Litleton, CO 80127, U.S.A.). US$50.Finance for the mineral industry, by C.R. Tinsley, M.E. Emerson, and W.D. Eppler. Society of Mining Engineers (Caler No. D, Litleton, CO 80127, U.S.A.). US$50. 2. Mintek reports The folowing reports are available from the Council for Mineral Technology, Private Bag X3015, Randburg, 2125 South Africa. They are free of charge to South African addressees, but there is a handling charge of US$25 per copy for reports sent to overseas destinations. Report M291D Removal of pebbles and pre-crushing of selected feed material in autogenous milling, by D.I. Hoyer. First issued Nov. 1986, reissued Apr. 1988. 16 pp Report M350 A survey of miling and mil-lining practice on South African gold mines, by M.S. Powel. Jun. 1988. 30 pp Report M356 The distribution of cobalt in mineral constituents of the Merensky Reef and UG-2 Chromitite Layer of the Bushveld Complex, by G. Smits. Jut. 1988. 13 pp Report M359 The development of a mobile laboratory for the monitoring of gold and cyanide in alkaline cyanide solutions, by R.V.D. Robert, C. Pohlandt-Watson, H.J. du Plessis, and G.D. Marshal. Aug. 1988. 17 pp. Productivity and technology The Metalurgical Society and Geselschaft Deutscher Metalhuten-und-Bergleute are sponsoring the Symposium on Productivity and Technology in the Metalurgical Industries, which is to be held in Cologne, West Germany, from 17th to 22nd September, 1989.Non-ferrous smelting Commemorating a centenary of lead smelting and refining at Port Pirie, the Conference on Non-ferous smelting wil be held at Port Pirie from 17th to 20thSeptember, 1989. International trade fairs From 20th to 26th May, 1989,4 major international trade fairs wil be held in Disseldorf, West Germany.

Jan 1, 1988

By J. A. Sweet, T. BACHMANN, G. E. Sandoval, T. M. Hauyon, F. A. Contreras

In many respects a porphyry copper ore concentrator plant can be considered as a simple system. Chalcopyrite typically liberates well at relatively coarse sizes, and even low grade ores are amenable to upgrading 20 to 30 times to produce concentrate grades in excess of 25 % in very simple Rougher- Regrind-Cleaner+Scavenger flotation circuits. The flotation response of chalcopyrite has been well characterised in many fundamental and applied research studies and the conditions necessary to depress pyrite and other floating gangue species are well understood. But what happens to the particle surfaces when you have a 50 km pipeline between the grinding circuit and the flotation plant? How does the seasonal variation in water quality affect your ability to control pulp chemistry? What impact does the relative concentration of the different sulphide species have on their separability? Why do two plants that receive nominally the same ore produce consistently different results? And most importantly, what do you need to do to improve the performance of both plants? To answer these and other questions, a focussed sampling and analysis programme was carried out at the Las Tórtolas flotation plants in 2018 and 2019. The work included full down-the-bank sampling, hot floats, the use of radioactive tracers for determining residence time distribution profiles, gas dispersion measurements, detailed mineralogy by size across the circuits and multiple regrind surveys. This comprehensive study was augmented by analysis of historical mineralogy, geometallurgy and operating data using modern data science techniques, and has provided the foundation for current and future optimisation initiatives. Some of the findings and their implementation will be presented in this paper. Keywords: Circuit optimization, Residence time, Gas dispersion, Pulp chemistry

Jan 1, 2020

By D. F. Malan, D. Ile

This study explores the use of backfill in hard rock bord-and-pillar mines to increase the pillar strength and extraction ratio at depth. The use of backfill will also minimize the requirement for tailings storage on surface and the risk of environmental damage. A literature survey indicated that backfill is extensively used in coal mines, but rarely in hard rock bord-and-pillar mines. To simulate the effect of backfill confinement on pillar strength, an extension of the limit equilibrium model is proposed. Numerical modelling of an actual platinum mine layout is used to illustrate the beneficial effect of backfill on pillar stability at greater depths. The magnitude of confinement exerted by the backfill on the pillar sidewalls is unknown, however, and this needs to be quantified using experimental backfill mining sections equipped with suitable instrumentation.

May 3, 2023

By G. L. Dyer, R. D. Alorro, R. E. Browner

A potential new rare earth extraction process has been suggested (Lazo, et al., 2017) (Lazo, et al., 2018) based on converting the rare earth elements to solid phase rare earth oxalates in an oxalic acid leach. Oxalic acid consumption is a significant issue in the process, therefore to improve the viability of this proposed new extraction method, a process to recover oxalate from the leach solution and recycle oxalic acid is required. A review of the literature and confirmation through thermodynamic analysis of the potential options identified precipitation of calcium or ferrous oxalate as the best potential options. The use of metallic iron to both provide ferrous ions as a precipitant and reduce ferric ions in solution would provide the most economical option, however slow kinetics and unreacted iron created significant issues with this process. The direct use of ferrous ions, while faster and more efficient, produced a precipitate with relatively poor solid/liquid handling characteristics and would require an intermediate stage utilising calcium in regenerating the oxalate. Utilising calcium chloride and oxide created very similar precipitates with better physical properties than the ferrous oxalate and that a reasonable proportion of the oxalate could be recovered before neutralisation of the solution induced precipitation of other phases such as iron oxy-hydroxides and calcium phosphate. The produced calcium oxalate was easily converted to oxalic acid and gypsum via immersion in sulphuric acid. It was also found that there is a significant loss of oxalic acid due to factors other than rare earth oxalate precipitation during leaching. This leads to a maximum oxalate recovery in the range of 50 %.

Jan 1, 2020

By R. Dehghan, M. Zarei, A. Tohry, S. C. Chelgani

Typical depressants for selective reverse flotation of iron oxides from complex silicates do not generally show high levels of efficiency. Therefore, as a hot topic, there are several ongoing investigations in this area. The main aim of this paper is exploring the potential of using humic acid (HA) as a depressant in reverse cationic flotation of hematite from complex silicates. For such a process, the wettability and flotation behaviour of pure minerals (hematite and silicates) was investigated at pH 10 in the presence of HA and cationic collector. Adsorption mechanism of HA on these minerals was measured by zeta-potential and FTIR. Results of flotation tests showed that at the lower concentrations of HA, selective separation of silicates from hematite is beneficial, where the floatability of amphibole was higher than pyroxene. A higher separation efficiency of hematite through reverse flotation was observed in the presence of amphibole, in comparison with the presence of pyroxene. Wettability studies showed that HA has a significant effect on reducing the hydrophobicity of treated minerals with the collector. The adsorption, ZPC and FTIR test results indicated that HA was adsorbed on both silicates and hematite. However, the absorption intensity onto hematite was much higher than silicates. It was found that the adsorption mechanism of HA on hematite takes place through both strong H-bonding and ligand exchange. Keywords: Reverse cationic flotation, humic acid, iron oxide, complex silicates, surface adsorption

Jan 1, 2020

By T. Szendrei and S. Tose

Historical approaches to the problem of flyrock based on correlation studies and regression analysis, including artificial neural networks and similar techniques, are inherently incapable of addressing two core issues – root causes of flyrock and projection velocity. A further shortcoming of correlation techniques is that they give no information on the influence of rock size and shape on the flight distance. The scaled depth of burial model for crater blasting in the collar zone and bench face does not specifically address the question of flyrock velocity. A third approach, based on flight trajectory calculations, often neglects the very significant effects of air resistance on the trajectory. Some trajectory models incorporate air resistance but use an implausible fragment velocity model that cannot propel sizeable rocks to distances much beyond 150 m. Nonetheless, trajectory calculation incorporating the effects of air drag affords the most promising approach to the prediction of flyrock range. A unique and insightful feature of the proposed realistic flight modelling is that it collapses all suspected causes of flyrock, many of which are not well understood, to just a single parameter – the launch velocity. This indicates that the root causes of flyrock lie in the mechanisms of momentum transfer to broken rock and suggests new avenues of study.

Dec 13, 2022