Search Documents

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Galis Mfg. Co. roof drill. The instructions are based upon two actual installations: one made in a mine on roof drill, model 300, and one in the factory. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other roof drills with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other roof drills and can determine any necessary modifications if they are not.

Jan 1, 1973

By Susanne Hering, Brent Kirby, Charles D. Litton, Tracy Allen, Kirk R. Smith, Rufus Edwards

In developing countries, high levels of particle pollution from the use of coal and biomass fuels for household cooking and heating are a major cause of ill health and premature mortality. The cost and complexity of existing monitoring equipment, combined with the need to sample many locations, make routine quantification of household particle pollution levels difficult. Recent advances in technology, however, have enabled the development of a small, portable, data-logging particle monitor modified from commercial smoke alarm technology that can meet the needs of surveys in the developing world at reasonable cost. Laboratory comparisons of a prototype particle monitor developed at the University of California at Berkeley (UCB) with gravimetric filters, a tapered element oscillating microbalance, and a TSI DustTrak to quantify the UCB particle monitor response as a function of both concentration and particle size and to examine sensor response in relation to changes in temperature, relative humidity, and elevation are presented here. UCB particle monitors showed good linearity in response to different concentrations of laboratory-generated oleic acid aerosols with a coarse (mass median diameter, 2.1 µm) and fine (mass median diameter, 0.27-0.42 µm) size distributions (average r2 = 0.997 ± 0.005). The photoelectric and ionization chamber showed a wide range of responses based on particle size and, thus, require calibration with the aerosol of interest. The ionization chamber was five times more sensitive to fine rather than coarse particles, whereas the photoelectric chamber was five times more sensitive to coarse than fine. The ratio of the response between the two sensors has the potential for mass calibration of individual data points based on estimated parameters of the size distribution. The results demonstrate the significant potential of this monitor, which will facilitate the evaluation of interventions (improved fuels, stoves, and ventilation) on indoor air pollution levels and research on the impacts of indoor particle levels on health in developing countries.

By Carl Belser

Approximately 30 million pounds of tungsten trioxide in the form of ferberite concentrates have been shipped from Boulder County. Since 1940, the production has varied considerably, being affected by the emergency needs of World War II and the Korean conflict. During World War II, attempts to stimulate production were made by the Metals Reserve Company by stabilizing the price for a specified period, the Reconstruction Finance Corporation by small mining development loans, and the Bureau of Mines and the Geological Survey, who cooperatively explored some of the district by surface and underground core drilling. During the Korean conflict and continuing through the first half of 1954) tungsten production was being stimulated by a Government-gauranteed price and by financial assistance loans under the Defense Production Act of 1950 to qualified operators of properties that have merited exploration. This combined program has increased production in Boulder County from about 1,900 pounds in 1949 to an estimated 383,000 pounds of tungsten trioxide in 1953. The 1953 production came from 67 properties. One of the problems confronting producers is the need for improved beneficiaton methods. Ores from the area have not been amenable to flotation concentration and gravity methods have resulted in poor recovery, often less than 70 percent.

Jan 1, 1955

By Frank A. Peters

A series of evaluations is being made to determine the relative processing costs of producing metallurgical-grade alumina from low-grade aluminous materials. These evaluations include the estimated operating and capital costs as well as recommendations for additional research and development to improve the processes and to lower their costs. The design for each process is based on published work. The three processes considered in this evaluation are designed to leach alumina as aluminum sulfate from calcined clay with sulfuric acid and to remove the silica residue by filtration. The filtrate from leaching is then purified by one of the following methods: Removal of iron in electrolytic cells using mercury cathodes; removal of iron by chemical precipitation through the formation of an iron-manganese complex; or precipitation of the alumina from an aqueous-ethanol solution, leaving iron in solution. Both the operating and capital costs for these processes are higher than those for the Bayer process. For plants producing 1,000 tons of alumina a day, the estimated operating costs per ton of alumina are: Electrolytic iron-removal process........... $81.35 Chemical iron-.removal process............... 82.08 Ethanol purification process............... 86.17 The investment in mercury is not part of the operating cost since this cost is considered equivalent to catalyst cost which would not be shown. The estimated capital investments for 1,000- ton-per- day plants on a Marshall and Stevens chemical equipment index basis of 240.0 are: Electrolytic iron-removal process...... $116,775,500 Chemical iron-removal process............... 99,418,900 Ethanol purification process................ 94,210,200 These investments include the working capital but not the land for each of the processes. Included in the electrolytic iron-removal process is an investment of $4,859,400 for mercury. Investigation of other methods for removing iron, of the decomposition operation, and of the leaching operation could reduce these costs.

Jan 1, 1963

This report describes the activities and publications of the Bureau of Mines Health and Safety Research and Testing Center, Pittsburgh, Pa., for the fiscal years 1960-65. It includes a discussion or work being conducted on roof control, dust explosions, ventilation, health, coal mine fire control, and electrical-mechanical testing, and an abstract of each paper published during the report period.

Jan 1, 1966

By J. H. Hedges

During the World War Leadville was an important producer of manganese and maganiferous ores for then steel industry. Normally, the market for these ores is limited to the requirements of the local steel mill at Pueblo for low-grade ores used in making, basic pig iron containing 1 to 2 percent Mr and spiegoloison containing 20 percent Mn, but during the war and a brief period of postwar readjustment, a good deal of 25- to 40-percent manganese ore qua shipped to in-stern steel-manufacturing centers. Throughout the active life of the camp, manganiferous iron ore carrying a little silver and lead and sometimes as such as 35 percent Mn was chipped to load smelters for flux. The total reordered production is 936,024 tons of metallurgical ore shinned to steel mills and 2,576,514 tons of fluxing ore, much of it of metallurgical grade.

Jan 1, 1940

By W. J. Fene, R. D. Currie

The value of protective clothing in the prevention of injuries has long been recognized in many of the leading industries , but the adoption of the idea into mine safety programs is comparatively new . Once started , however , the idea has grown rapidly and the results already obtained by mining companies have shown that it is fundamentally sound . Both coal and metal mining companies are rapidly adopting these protective measures , and since 1924 many mines have become well equipped with eye , head , and foot protection . At the present time approximately 70 percent of the employees in the anthracite mines of Pennsylvania are provided with safety hats . At many metal mines all employees are provided with safety hats, shoes , and goggles . The Pennsylvania mining law provides that all shaft · workers in anthracite mines shall wear protective hats . In According to a study³ made of the nature of 3,485 temporary injuries and of the parts of the body of underground coal mine employees most exposed to occupational hazards , the head and face were injured 665 times , the hands 856 times , and the feet 565 times . Of 2,555 temporary injuries in metal mines , the head and face received 484 , the hands 788 , and the feet 357 . a similar study4 made by a coal -mining company for the year 1928 , of 556 injuries the scalp received 9 , the skull. 4 , the eyes 47 , the hands 62 , the thumbs 21 , the fingers 141 , the ankle , the feet 51 , and the toes 35 . Probably most of these injuries could have been prevented by suitable protective clothing and equipment . This study also revealed that at least one injury occurred

Jun 1, 1933

By H. W. Clair, E. V. Potter, M. J. Speedlove

"INTRODUCTION The behavior of particles in a sound field has long been of scientific interest since Kundt (1) 5/ made his classic experiments on some of the interesting effects of standing waves in cylindrical tubes. With the development of the electronic tube and its application to continuous generation of sound, experimental investigation of the Kundt tube was renewed (2). The more intense vibrations set up by a continuously vibrating diaphragm or rod produce even more striking effects than those observed by Kundt. Instead of the striations at the antinode produced by the stroked rod, then, wafer like barriers are formed at the antinodes, sometimes extending over the entire cross-section of the tube. Furthermore, it was observed independently by Andrade (3), Brandt, Freund and Hiedemann (4); and by investigators in the Bureau of Mines laboratories (5) that aerosols, such as ammonium chloride or tobacco smoke, could be flocculated quickly if passed through an intense sound field, particularly when a standing wave field was set up by a resonant enclosure. Because of its possibilities as a new means for removing suspended particles from dust-laden gaseous furance or smoke, the phenomena attending the behavior of suspended particles in a und field have been studied intermittently by the Bureau of Mines over the past decade.The first experimental work was done with a magnetostriction vibrator and a Hartmann air-jet generator as sound sources. It soon became evident that neither type was entirely satisfactory. Low mechanical efficiency is an inherent characteristic of magnetostriction generators, and the air-jet generator is difficult to control and does not permit accurate measurement of the acoustic output. The search for a suitable sound source led to the development of an electromagnetic generator, which is by far the most suitable for study of the effects of intensive high-frequency sound fields in gases (6)."

Mar 1, 1948

By R. Blickensderfer

Laboratory wear testing was conducted by the Bureau of Mines on a variety of typical wear-resistant alloys used in mining and mineral-processing equipment to establish their relative spalling and abrasion resistance. Test specimens in the form of 75-mm-diam balls were subjected to repeated impacts until they broke, spalled excessively, or received several hundred thousand impacts. Pin specimens removed from the balls were evaluated for high-load abrasive wear. The alloys in-cluded commercial forged steels, cast steels, manganese steels, and four types of white cast iron, with a range of heat treatments. The effects of hardness and microstructure on impact wear and abrasive wear are discussed. The data should help mine operators select the compositions and heat treatments that best suit service conditions.

Jan 1, 1985

By E. J. Gleim

[THE ORGANIC act under which Federal Bureau of Mines was established provided for the investigation of the safe use of electricity in mines. Each Congress appropriates funds for conducting this investigation. As part of this investigation, electrical apparatus used in mines is studied to determine if its operation and use might introduce a hazard. From this study, certain safety standards have been developed. These standards, established with the aid of both the manufacturer and user of such apparatus, are published in schedules, and apparatus that complies with the requirements set forth these schedules is classified as "permissible." This term is defined to designate apparatus as "completely assembled and conforming in every respect with the design formally approved by the Bureau of Mines." In the judgment of the Bureau, the manufacturers of such apparatus have adhered to certain minimum standards of safety in supplying a product that when properly used and maintained is safe for operation in mines where flammable gas or coal dust may accumulate. This work of the Bureau of Mines for increasing safety does not make it obligatory for manufacturers of mine equipment to produce only that of permissible classification. Before the effective date of the Federal Mine Safety Code,5 the Bureau sought to promote safety by recommending that mine operators install permissible equipment in gassy mines as a preventive measure against gas and dust explosions initiated by electrical equipment. For some years, the mining laws of several States have prescribed the conditions under which permissible equipment must be used. The Federal Mine Safety Code requires that ?all new electric face equipment and replacements of equipment purchased for mines where nonpermissible equipment is now being used shall be of a permissible type approved by the United States Bureau of Mines,]

Jan 1, 1955

By Oliver C. Ralston

The minerals that enter welding-rod coatings and fluxes are the main subject of this report. Few mineral producers know just what minerals and what grades and quantities of minerals are required by the welding trade, and it is for their information that this report has been prepared. The various methods of welding are discussed extensively enough to inform this type of audience. Specialists in welding probably will find little on welding that is of value to them, but they may learn something more about the minerals or mineral products that they use. The authors did not find it easy to prepare this publication, and any needed corrections will be welcomed. Regarding welding, research, Jenks4/ 1 points out that while the process of welding in simple in operation, the phenomena attending its use are extremely complicated, and the efficient and safe use of welding requires an understanding thereof. Although the fluxes and the coatings used have solved many problems, many other problems require the joint effort of the whole industry; therefore, it is hoped that this report will be found of practical value.

Jan 1, 1940

By R. B. Tippin

To study continuous operation of the heavy liquid separation (HLS) of minerals, the Bureau of Mines concentrated spodumene from a typical ore. The studies included heavy liquid concentration, removal of the heavy liquid from the mineral products, and recovery of the heavy liquid for reuse. The research program examined the influence of feed moisture, steam consumption, stripping time, and condition of steam. Operation of multiple cyclones in series resulted in spodumene concentrates assaying 92 to 95 percent spodumene and indicated mineral recoveries of 86 to 89 percent. Continuous filtration and steam stripping produced mineral products containing less than I pound of heavy liquid tetrabromoethane (TBE) per ton of material. Problems unique to this process are discussed, including heavy liquid properties and viscosity, toxicity, material handling hazards, and safety precautions.

Jan 1, 1970

By M. M. Ayoub

With a return to coal as a major energy source for many companies, more emphasis is being placed on recovery of coal from areas that were formally considered uneconomical to mine. Increasing emphasis is being placed on production from low coal (seam height 48 inches or less) as high coal seams are depleated. Mining in restrictive spaces requires unusual work postures that can turn easy jobs into demanding ones. The objectives of this research were: (1) to evaluate the job demands associated with low coal mining, (2) to survey the anthropometry, strength, and aerobic capacity of low coal miners to determine if they differ from the U. S. population, and (3) to recommend, on the basis of available information, optimal job and work station design for low coal mining. This research effort was supported by the U. S. Bureau of Mines. The male and female anthropometry with the exception of weight and circumferential dimension, was quite similar to the comparison population. Back strength for male and female miners was significantly lower than the industrial worker population. This can be one of the contributing factors of low back problems in mining. Shoveling, timbering, and helpers tasks were physiologically demanding activities. However, due to the frequent stoppage of work, adequate rest was usually available. If work stoppage is corrected, then better work/rest schedules are essential.

Jan 1, 1981

The Bureau of Mines has sponsored a comprehensive research program to enhance the safe, effective, and efficient use of blasting technology by the mining industry. Recent research results of the surface mine blasting program were presented at a seminar on April 25, 1987, in Chicago, IL. Many of the topics discussed at the seminar are presented in this proceedings. The new research described in these papers includes computer monitoring of rock motion, the influence of blast delay times on rock fragmentation, blasting effects on Appalachian water wells, blast vibration measurement near structures, and the reduction of accidents through improved blasting safety.

Jan 1, 1987

By Lloyd Williams

1. The investigation shows that the Coal Creek has been the most productive, bed in Campbell County and contains the largest recoverable reserves of coal. The Pewee, Red Ash, and Jullico have been relatively productive beds and contain appreciable recoverable reserves of coal. The Blue Gem also has been productive in the past, but available information indicates that most of the remaining coal is Less than 28 inches thick. The Big Mary has relatively large reserves over 28 inches thick, but the coal is high in ash and sulfur. Thick partings in the Windrock bed have discouraged mining in that bed. The Poplar Creek and Rex beds generally are below drainage, and large areas have been excluded from the reserve estimate, Reserves in the Walnut Mountain bed will be difficult to mine due to the irregu¬lar thickness and lack of continuity of the bed. Estimated coal reserves are- small in the remaining five beds. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-Foot of coal in place, are estimated to be 398 million tons as of January 1, 1953, o? this total, 267 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, these should be added to the total estimated reserves.

Jan 1, 1956

By L. C. IlsLey

Explosives have been fired electrically for several decades. Mountains have been tunneled, deep shafts sunk, extensive coal and metal mine workings excavated and, in times of war, railroads, buildings, bridges, and fortifications have been destroyed by means of electrically fired explosives. Modern engineering depends so much on explosives that their safe and efficient handling and especially their detonation are of prime importance to all those connected with the use of explosive agents. Electric shot-firing is only one method of igniting explosives, but it is rapidly spreading and because of certain inherent safety features should be encouraged. Data collected by the Bureau of Mines indicate that in the United States a large percentage of the blasting in quarries, shafts, and tunnels, and from 15 to 25 per cent of the blasts in mining operations, are set off electrically. The Bureau of Mines is interested in electric shot-firing because of its use in mining, and especially because electric methods, when properly applied, are undoubtedly safer than other methods commonly used.

Jan 1, 1926

By J. O. Lewis, Carl H. Beal

The material for this paper was collected for the most part by C. H. Beal during the years 1916, 1917, and 1918. Many of the conclusions reached in regard to the life of oil wells have already been published by the Bureau of Mines 1 but those presented in this paper deal particularly with the theoretical aspects of oil production. The report discusses some of the fundamental factors governing oil production, taking up first the conditions affecting the. amount of oil in the oil sand, then those factors that control the rate of production of oil wells, and then discusses several related problems, most of which deal particularly with the effect of the production of one well on that of another.

Jan 1, 1921

By Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

A survey of pillar conditions was carried out at 21 operating limestone mines that use the room-and-pillar method. The surveyed pillars were all located in rock that was classified as “Good” to “Very Good” using the RMR rock mass classification system. The average pillar width was 14.5m and the width to height ratio varied between 0.53 and 3.52. Pillar conditions were rated using a visual rating system that accounts for the effect of geological structures as well as stress related fracturing. Nine cases of pillar instability were recorded. Pillar instabilities were typically limited to individual pillars or small groups of pillars within an otherwise stable layout. Local geological structures such as inclined discontinuities or weak bedding planes contributed to instability in seven of nine cases that were observed. Elevated pillar stresses contributed to instability in the two remaining cases. All the unstable pillars observed had width-to-height ratios of less than 1.5. It is concluded that pillar instability is most likely to be caused by unfavorable geological structures in pillars with width to height ratios of less than 1.5. Stress related instability such as rib spalling becomes more prevalent when the average pillar stress approaches approximately 20 MPa.

By F. L. Wideman

This paper lists resources of sulfur in Wyoming, Colorado, Utah, New Mexico, and Arizons, an area comprising approximately 522,600 square miles, Sources of sulfur occuring within the region are sulfur are, pyrite and pyritic ores, and natural gases and petroleum. Data concerning these sources are presented on a statewide basis. Some of the known deposits of sulfur ore are surficial and of fumerole origin; other deposits have resulted from oxidation of pyrite or sulfide ores of copper, lead, and zinc. The deposits are small and the sulfur is distributed erratically in them. There is a small production from some of the deposits, and the material produced is used as soil conditioner.

Jan 1, 1957

By Shirley F. Colby

The past 40 years have seen the sand and gravel industry grow from small roadside pits and holes in farmers' back yards to giant corporations selling millions of tons of sand and gravel each year and owning plants representing huge capital investments in land and equipment. The days hen a man could "work out" his taxes by providing the materials for nearby roads are gone forever. In addition to the hundreds of privately owned and operated plants, Government agencies operate sand and gravel pits and plants to supply aggregates for the tremendous road-building and public-works programs in progress during the past few years. EXPANDING PRODUCTION In 1940 the send and gravel industry produced almost a quarter of a billion short tons valued at more than 110 million dollars. This compares with less than 2 million short tons worth 1 1/2 million dollars produced in 1902. The practice of screening sand and throwing away the gravel in the early days of the industry's growth has stopped, and in 1940 gravel constituted two-thirds of the total production. In 1906, the first year in which sand and gravel were reported separately gravel accounted for only one-

Jan 1, 1942