Search Documents

By Ron Woolf, Corry Goumans

With increasing traffic volumes experienced thro u g hout North America, a common goal for Highway officials is to keep traffic flowing as much as possible and to keep disruptions to the flow to a minimum. Our experience throughout the US and Canada has shown that all Departments of Transportation are under extreme pressure from the private sector to keep highways open for various reasons, convenience and revenue being the most common. For example, on Highway 99, from Vancouver, BC to the Whistler resort area, local merchants, homeowners and ski hill operators exert extreme pressure on the Ministry of Transportation to keep the highway open, and in Pennsylvania, the Turnpike Commission requires traffic to flow on a continual basis. Loss of revenue in these two cases is the main impetus to keep the traffic moving.

Jan 1, 2003

By N. Paley

An engineering project was undertaken at the Cominco Alaska Red Dog Mine to determine the extent that Semi-Autogenous Grinding (SAG) mill throughput could be increased by blasting differently. The Julius Kruttschnitt Mineral Research Center (JKMRC) blast fragmentation, jaw crusher, and SAG mill breakage models were used to relate changes in the blast design to the SAG mill performance. For optimum performance a SAG mill requires a particular size distribution; a number of large rocks to facilitate breakage by impact, as few as possible middle size rocks that become critical size, and the maximum fines which will pass quickly through an open-circuit mill. Physical constraints of drill and charging equipment size limit the extent that pattern geometry can be changed and the powder factor increased to maximize fines. However, JKMRC research had shown that it appeared possible to increase primary breakage by blasting to such an extent that SAG mill throughput could reach a plateau or even begin to decrease. Modeling was carried out on a range of blast pattern geometries and emulsion explosive blends to determine if a plateau existed and at what powder factor it would be reached. It was found that the relationship between powder factor and grinding throughput was nonlinear. Modeling was also used to compare the SAG mill throughput which could be expected from different emulsion explosive blends to determine which blends should be used in dry and wet holes to provide similar fragmentation. For heavy-ANFO mixtures, the highest modeled throughput was at a ratio of 30/70, with ratios on either side indicating lower throughput. For emulsion blends, the highest modeled throughput was at a ratio of 80/20; however, ratios from 80/20 to lOO/O were similar. Crusher product size distributions were obtained from belt cuts early in the analysis to confirm model predictions. At later stages, actual SAG mill throughput was compared to predicted. The economic benetit from the different blast designs was calculated by accounting for the reduction in recovery due to the higher throughput and the additional drilling and blasting costs. Increasing the powder factor by 150% from the 0.29kg/t {0.58lb/st] being used to 0.72kg/t { 1.44lb/st}, the maximum feasible with mine equipment, could provide a sign&ant net benefit of $3OWyr due to the increased concentrate production. However, because the relationship between throughput and recovery is affected by other factors which were not modeled, a more conservative approach was taken. The powder factor was instead increased by 50°h, providing 45% of the gain. This was possible because the relationship between powder factor and grinding throughput was nonlinear.

Jan 1, 2001

By Charles Clark, Mark Mukhija, Jaime Klein

Comminution – the reduction in size of solid materials – is the most energy intensive component of the mining process (Bauer, 2015). It is estimated that comminution consumes around three percent of all electricity generated in the world (Ceecthefuture.org, 2017). On an energy equivalent basis, downstream processing consumes six times more energy than drilling and blasting (Kanchibotla, Sarma et al., 2014).

Jan 1, 2018

By Donald F. Rapp

Improvements in non-electric initiation systems have given the blasting industry more choices than ever in controlling blast results. By incorporating blasting requirements and system attributes, timing patterns are only limited by the creativity of the shot designer. This paper will discuss the basic groups of non-electric initiation systems, their attributes, and how to select the optimum system for the job.

Jan 1, 1991

By Richard J. Mainiero, Marcia L. Harris, James H. Rowland

In the past several years, there have been a number of blasting-related carbon monoxide migration incidents. In each case, there have been some common factors that appear to be related to carbon monoxide migration. Geology, heavy confinement of the blast, close proximity to the affected structure, and open pathways into the affected structure are just a few. Prince William County, VA is an area undergoing a boom in suburban development. In the year 2001, more than 4,050 new homes were constructed within the county.1 In the new housing development located in Bristow, VA, trench blasting was utilized to excavate proposed sewage and utility lines. On November 8, 2002, a trench blast was conducted for the installation of utility lines. Later that evening a carbon monoxide detector alarmed in a nearby house. The gas company and fire department sampled for carbon monoxide and measured 100 ppm and more than 200 ppm on the first floor and in the basement respectively. Subsequent efforts to prevent migration of CO into the nearby homes met with mixed results. The only reliable technique for protecting neighbors from CO appears to be the placement of CO monitors in the homes. The events are presented and discussed.

Jan 1, 2004

By Dale S. Preece, Ruilin Yang

"Air-decking has been used frequently in blasting for many decades. It has been asserted that an air-deckcan alleviate excessive shock pressure from the detonation of a charge thereby producing better energy distribution in a blast overburden, for example. Research on air-decking has been active and various theories have been postulated that mostly support the effectiveness of air-decking for improved blast efficiency."

Jan 1, 2017

By Jhon Silva

"Signature Hole and Waveform Superposition techniques used to predict and control mine blast ground vibrations require a clearly defined information collection configuration. The collection of this information determines the scope and success of the ground vibration prediction. Application of the Improved Signature Hole technique using the Silva-Lusk equation requires the collection of at least two informational elements from any specific production shot. The first required element is a signature waveform, and the second element is the overall production blast waveform. The signature waveform depends on detonated charge variables such as the amount of explosive in use, use of decking, the possible detonation of several holes at the same delay, and many others. The production blast waveform is beneficial to the Improved Signature Hole methodology when used to calibrate the model, and toobtain accurate vibration predictions for different timing configurations."

Jan 1, 2017

By Kahmmelly Mathildes Pimenta Coelho, Felipe Dantas, Jaine Ribeiro de Souza, Augusto Ferraz, Carlos Roberto Campos Junior, Davi Bastos Martins de Oliveira

The Carajás Iron Mine, recognized as the largest iron ore province in the world, is notable for its continuous efforts to improve operational efficiency and safety. In response to these objectives, a QA/QC (Quality Assurance and Quality Control) Program was implemented and integrated with Blastscout Probe technology to optimize drilling and blasting processes. The program supports the standardization of operational parameters, the execution of regular audits, and real-time data analysis, facilitating precise and timely adjustments. The implementation led to significant improvements, including an 80% increase in operational compliance, a 49% reduction in drilling depth deviations, and a 30% enhancement in Jaspelite fragmentation. This study presents the methodology employed, the outcomes obtained, and the positive impacts observed in both operational performance and environmental management.

Jan 26, 2026

By G. Walsh, L. Wolkovitch, A. Savage, V. Romero, T. Zimmerly, G. Imahara, J. Hyneman, K. Byron, D Tapster, S. Belleci, J. Metzger, M. Stanley

Testing was conducted at the Energetic Materials Research and Testing Center for the MythBusters on three separate occasions. This testing included (1) an experiment designed to create diamond from graphite using the shock and pressure of a detonation, (2) the flattening of a car using a steel plate driven by a rocket sled, and (3) the bifurcation of a car also using a rocket sled. All tests were successful; diamond was produced following the detonation of ANFO, and extracted from a graphite / cobalt matrix. A plate was accelerated to 646 mph (1040 km/hr) using a two-stage sled system loaded with 5” (12.7 cm) high velocity aircraft rockets (HVAR) into a car, which was subsequently demolished. Finally, a steel wedge was pushed to 541 mph (871 km/hr) by a one stage sled using HVAR rockets, and was able to cleanly cut a target car in half.

Jan 1, 2010

By Michael S. Wieland, Thomas C. Ruhe

Marginal detonation of explosives can produce more toxic fumes with higher nitrogen oxides (NOx) than normal detonation. In delay blasting, shock waves from borehole charge explosions can impact those delayed charges still remaining in the delay pattern. This can result in partial desensitization, whereupon the explosive does not misfire, but detonates in a weak unstable fashion releasing a different/unusual spectrum of gaseous reaction products.

Jan 1, 1991

By Yves Lizotte, Malcom Scoble, Pierre Michaud

The concept of optimum fragmentation in surface mining operations, i.e. the degree of fragmentation to which corresponds the lowest overall associated costs of drilling, blasting, loading, haulage and crushing, was developed more than thirty years ago. Recent field investigations using novel technologies, which have been completed by ICI Explosives Canada and by others, indicate that this ultimate goal of optimum fragmentation is closer to becoming reality.

Jan 1, 1997

By Mauro Fornaro, Marilena Cardu, Renato Mancini, Daniele Castano

Tunneling by explosive blasting in civil works isn't merely intended to break somehow a way through the rock, rather to drive a permanent, constant cross section, lined way. The current mechanical excavation v/explosive blasting debate is mainly centered on the concept of the tunnel wall quality; and consequently explosive blasting strategy is founded on contour blasting.

Jan 1, 1992

By Lazar Kricak, Zoran Teodorovis, Dragan Bogunovic

Scattering of delay interval around nominal value is an important issue in blasting practice. The scatter interval, as becomes wider, increases a probability of time delay overlapping adjacent blastholes. An excessive flyrock, ground vibrations, air blast and poor fragmentation are the symptoms for scattering related problems. Utilization of the short delays in the blastholes and longer delays on the surface are recommended solution to overcome mentioned problems. In contrast to global trends manifested through the application of electronic detonators and non-electric shock tube systems, revitalization of inexpensive electric detonators in combination with an accurate initiation system may be an acceptable solution. An extensive work was carried out at the Blasting Center Laboratory at the College of Mining and Geology, University of Belgrade, to develop a precise initiation system. As a result, Sequential Blasting Initiation System – Radio Frequency (SBIS-RF) was developed. It is expected that this system will increase blasting productivity, and reduce negative environmental impacts and total blasting costs.

Jan 1, 2008

Almost one half of Canada's total land surface is underlain by permafrost. This term describes the thermal condition of earth materials when their temperature remains below 0°C continuously for a number of years. The drilling and blasting of frozen materials requires more energy than the blasting of same in its unfrozen state. The cost of comminution could double in permafrost even with adequate organization, drilling equipment and proper explosives.

Jan 1, 1975

By Dr. Anurag Agrawal, Steve Franklin, Clint Zimmerman, Elijah Williams

In a time when data has become a highly valued commodity within many mining and quarry operations, managing large amounts of current and historical information can be difficult. If not managed properly, trying to leverage the data to make informed operational decisions promotes another challenge. Geographic Information System (GIS) is an environment that uses computers and software to create, manage, analyze, and map all types of data. Currently, the mining industry is faced with a challenge to produce the demanded critical metals and minerals that drive our economies. GIS is leveraged in many large mining industries today to help drive decisions, save cost and plan for future operations. Specifically in the Drilling, Blasting and Quarrying industries, data is being captured at many different levels, whether it is a subsurface geological, blast performance, quarry surveys, loading and hauling, or crushing performance. Pen and paper logs and reports compiled lack the dimension that GIS can bring for extracting value from real-time or historical data. GIS connects data to maps, integrating location data with all types of descriptive information. Paired with Artificial Intelligence, additional analytical layers can be built on platforms to extract data and automate workflows. Having the ability to encompass several forms of collected data to drive operational decisions can bring huge savings to the bottom-line. This paper will dive into the areas where GIS data can drive value into operations by assisting in the management and analysis of the types of data being captured, specifically with Drill and Blast. Whether it is tracking haul road conditions, monitoring locations of equipment, environmental conditions, quantifying blast performance or developing a quarry plan based on geological models. GIS can collectively encompass all of this data to bring tremendous value to the operations, improving safety, efficiency and production.

Jan 21, 2025

By Jared Redyke

Thursday, October 14, 1999 marked another important milestone for America’s space program. At exactly 10:05 AM EST on a beautiful, sunny Florida morning, Dykon, Inc. of Tulsa, Oklahoma detonated approximately 300 pounds of explosives to fell the seven million pound Umbilical and Mobile Service Towers at Space Launch Complex 41 (SLC-41) at NASA’s Cape Canaveral Space Station. Completed in 1965 at the height of the Space Race to the moon, the Mobile Service Tower/Umbilical Towers (MST/UT) were part of the Titan rocket launch facilities. The MST was 265 feet high and weighed over five million pounds. The UT was 175 feet high and weighed over 2 million pounds.

Jan 1, 2001

By Magnus Gynnemo

The primary purposes of drilling and blasting in hard rocks is to fracture solid rock and prepare it for excavation and subsequent transport to the crushing plant. Using explosives in excavation operations without counting for the geology gives no consideration to the quality of the macadam product or the excess production of waste material (fines).

Jan 1, 1997

By Jack Eloranta

This paper documents the relationship between material handling and processing costs compared to blasting cost. The old adage, "The cheapest crushing is done in the pit", appears accurate in this case study. Comparison of the accumulated cost of: powder, selected wear materials and electricity; indicate a strong, inverse correlation with powder factor (lbs powder/long ton of rock). In this case, the increased powder cost is more than offset by electrical savings alone.

Jan 1, 1995

By William A. Travnik

For more than 60 years, ESSO RESOURCES CANADA LIMITED has been producing and refining oil at a small refinery in Norman Wells, Northwest Territories, and supplying diesel fuel and other oil products to northern markets. In 1982,ESSOwas granted governmental approval to expend production from the oil field from 475 cubic metres a day to 4400 cubic metres a day. This $800,000,000projectproceeded ahead of schedule for a start up in 1985.

Jan 1, 1986

By Zoltan Susanszky

The total available energy in an explosive charge is seldom fully utilized in industrial operations. For this reason more explosive is normally used to perform a job than we would calculate. In an explosive detonation some energy is generated as waste energy which can not be efficiently used. This results in added expense and possible environmental damage. This waste energy can create problems in metal forming with explosives and during commercial underwater blasting operations.

Jan 1, 1976