Search Documents

By Doug Hoy

The scope of the Cliff Avenue Reconstruction Project in Sioux Falls, South Dakota was to widen a two lane highway to five lanes, along with removing and reconstructing both above and below ground utilities located along the project limits. The objective of this paper is to present the blasting techniques used in the rock excavation phase of the Cliff Avenue Reconstruction Project.

Jan 1, 1992

By Adrian Moore, Alan Richards

Time window techniques that limit the explosive charge mass being fired within a specified time window (commonly 8 milliseconds (ms)) have been used for many years and are widely accepted by explosives engineers. The 8 ms time window may be relevant for controlling ground vibration for small blasts at close quarters in a high frequency vibration environment. For controlling ground vibration from blasts in a low frequency vibration environment an 8 ms separation between blastholes is arbitrary and meaningless. The 8 ms time window was never intended as a means of controlling airblast. The use of time window techniques will, in many instances, result in airblast and ground vibration levels that are substantially greater than planned, with unfortunate outcomes. The uses of time windows that are inappropriate have been well explained in previous papers. This paper gives further examples of blast designs that satisfied time window considerations but have resulted in substantially greater airblast and ground vibration levels in certain directions, due to wavefront reinforcement or the combined effect of drilling pattern and delay sequence. Techniques that identify wavefront reinforcement, due to the combined effect of drilling pattern and delay sequence, can assist explosives engineers to avoid blast vibration problems that result from inappropriate time window techniques.

Jan 1, 2002

By John R. Holliday, William Marcum

Apogee Coal Company, DBA Arch of West Virginia, faced the challenge of drilling and blasting over one million cubic yards of high temperature overburden at its Ruffner surface operation near Logan, West Virginia. The overburden was removed above the Upper Five Block seam that was previously deep mined, abandoned, and later engulfed by fire. Borehole temperatures were measured above 700° F.

Jan 1, 1996

By Gerald R. Coonan

I'm really here to talk about my pet subject of government relations. I've been in Peabody's Environmental Quality Department, working on regulations, for over five years, and I have seen a number of individuals in the coal industry who were completely stunned when a new regulation was brought to their attention. Their first reaction was, "where did this come from"?

Jan 1, 1980

By Jorge Cárdenas, Piero Mejía, Diego Gamarra

The present case study details the solution to a complex situation in a mining operation, involving the challenge of expanding the tailings storage facility in high-criticality areas adjacent to electrical rooms that provide continuous power to the entire mining process, including water pumping and drainage systems. For this purpose, blasting is required to prepare the construction areas for the new expansion facilities. Upon deciding to proceed with blasting, a comprehensive engineering assessment was conducted to ensure operational continuity without impacting the process, while generating sufficient fracturing in the rock mass to allow extraction with auxiliary equipment. Support from specialists through the Technical Assistance area was requested, and a detailed evaluation was carried out through advanced studies. Field vibration studies were conducted to define attenuation models and characterize the rock mass in the sector. With this information, simulations were carried out using predictive and probabilistic models with Monte Carlo methods to select delay charges and optimal timing for reducing vibration levels and increasing frequency levels. With these measures, the three blasts conducted near the Gas Insulated Substation room, which had distances ranging from 30 to 100 meters, produced the following results: • Vibrations; The three blasts conducted at distances of 100, 30, and 50 meters recorded vibration values of 5.3, 40.2, and 9.5 mm/s, all of which were below the maximum vibration level of 50 mm/s set by the projects area. According to the USBM RI8507-OSMRE standard, all values for Peak Particle Velocity (PPV) and frequency were below the permissible limits. • Flyrock; Through filming and post-blast inspection, it was confirmed that the ejections were within the safety zone. • Fragmentation; The results obtained showed a maximum overbreak size of 1.5 meters, allowing the broken material to be moved effectively.

Jan 21, 2025

By Timothy Fogarty, Gregory Poole, Roger Reeder, David Switz

This project involved the construction of a new pump station and intake structure at an existing water treatment facility. Although the project involved a significant amount of rock removal, the specifications said no blasting.

Jan 1, 2012

By Lewis L. Oriard

Both theory and experience tell us that spatially distributed energy sources generate a more complex family of seismic waves than do point sources. The resulting effects in the near field (for close-in blasting) are significantly different than those from point sources although, at great distances from the source, the seismic waves take on many of the characteristics of point sources and can often be treated as such.

Jan 1, 1992

By Paul McAnuff, Alastair Grogan

In Canada, the only vibration regulations which apply across the entire country are intended to protect fish spawning areas. The Provinces and Territories regulate mines and quarries, and are responsible for setting vibration and airblast regulations. Some Provinces have set specific regulations, while others leave these restrictions to the mines inspectors who can set limits on a case by case basis. For the most part, it is left to individual municipalities to regulate blast vibrations and airblast from other blasting activities, which differ from jurisdiction to jurisdiction, and in some cases are not enforced. Blasters working in different jurisdictions have to be aware of the applicable regulations for the area they are working.

Jan 1, 2005

By Grant Small, Deon Pieterse

Reactive ground conditions at an open pit manganese mine in the Northern Cape of South Africa resulted in an unexpected detonation.

Feb 1, 2020

By Daniel Castelo, Ben Potter

This paper will discuss the most efficient and effective way to use shape charges when considering standoff distances and the amount of an explosive to be used. For each shape charge test that was performed, a one inch diameter copper liner of 90o was used. Different standoffs for each shape charge were tested to see which one would penetrate the deepest into rolled homogenous armor steel (RHC 44). It was determined that a standoff of three cone diameters provides the deepest penetration. In addition to testing for optimal standoff distances, the effects of overfilling as well as under filling a shape charge with explosive was tested against a shape charge with the bare minimum amount of explosive for correct detonation. These “fill” tests were all performed at a standoff of three cone diameters. Overfilling has little to no effect towards penetrating deeper into a target while under filling a shape charge has an effect of shorter penetration. C-4 explosive was the main explosive for all shape charges.

Jan 1, 2011

By Rohan Stevens, Katsuhiro Kameyama, Osamu Iwata, Jinming Liao

In densely populated cities such as Hong Kong, where unoccupied space is becoming more valuable as the population grows, city planners are more often looking to underground space to meet the increasing need for transportation and services. Given the dense population of people, amenities and high-rise buildings above or near such underground space, it is essential to minimise any disturbance and potential damage during construction. Hence, the excavation of hard rock to develop such underground space can be highly restricted, expensive and time consuming. This is the case for many of the tunnels currently being excavated by drill and blast directly underneath Hong Kong’s busiest business districts and most popular residential areas.

Jan 1, 2013

By Karl Kure, Anders M. Heltzen

Mixtures of prilled ANFO and 0,5 - 3 mm polystyrene balls are interesting substitutes to the tube charges or other types of reduced explosives or detonation fuses. Experiments have shown detonation ability even of a mixture of 95% bolt polystyrene balls and 5% ANFO. The gas and shock energy in the mixtures decrease proportional with the content of polystyrene. The detonation velocity shows higher values than expected for mixtures with more than 50% (vol.) ANFO.

Jan 1, 1980

By Jerry Wallace

Two recent-release boulders posed serious threats to public transportation and utilities in Washington State. Both required challenging drilling and blasting solutions.

Jan 1, 1997

By Emmett J. Ientilucci, Martin Held, Xuesong Liu

Mining is crucial for advancing technology and science by providing essential resources and materials. Quarry blasting, a necessary process in mining, releases these resources and chemicals, driving research and engineering improvements. However, NOx (nitrogen oxides) is an undesired contaminant produced during quarry blasts, posing a significant negative impact on mining activities. Therefore, detecting and quantifying NOx emissions is essential for designing effective blasts, analyzing their dynamics, and reducing contaminant production. Image processing and machine learning, including deep learning methods, have been applied to solve smoke plume detection and segmentation tasks. Most research has focused on smoke from campfires or forest fires, which are important for early fire and smoke detection. However, there is limited research on quarry blast smoke using machine learning methods, which presents challenges for recognizing the smoke plume from complex background scenarios and objects, including collapsed rocks, scattered soil dust and dirt, and the dynamic movement of the scene due to blast vibrations. Detecting NOx within the smoke plumes is further challenging because NOx must be distinguished from the overall smoke plume, as they share many common spatial features. To resolve this issue, we propose an ensemble method for NOx detection that combines smoke plume segmentation with NOx fume detection. First, we apply a smoke plume segmentation model to identify the smoke plume regions. Then, we use these masked-out smoke plume regions to detect NOx based on its unique color features. The first stage of the ensemble method helps block out complicated confusers in the background, such as reddish and brownish dirt. Next, we specifically design a color classifier for NOx to further improve its sensitivity. We evaluate the overall video-wise performance using accuracy, false alarm, and miss rates based on sampled image frames from videos. Additionally, we assess the mean Intersection over Union (mIoU) for smoke plume segmentation and the mean Average Precision (mAP) for image-wise performance from an algorithmic perspective. In summary, this paper represents the first attempt to apply machine learning approaches to NOx detection in a memory-efficient and time-efficient manner.

Jan 21, 2025

By Jorge Cardenas, David Martinez

Blasting-induced vibrations can be predicted with high precision, allowing for the optimization of sequence design, delay timing, and charge configurations to minimize their indirect impact on rock masses. This optimization leads to a reduction in peak particle velocity (PPV) and dominant frequency at monitoring points. However, a crucial aspect of slope safety is estimating the degree to which vibrations influence stability through numerical modeling of the dynamic response. Slope stability is closely linked to rock mass strength, the predominant failure mechanism based on discontinuity orientation relative to the slope face, and the pre-existing stability conditions before dynamic alterations occur. Blocks, wedges, and planar failures tend to slide under lower vibration levels and are more susceptible to resonance, particularly in fractured and low-strength rock masses. To evaluate the interaction between rock mass and vibrations, photogrammetry and artificial intelligence were employed to identify discontinuity families at vibration monitoring sites. This data facilitated the development of artificial discontinuity networks (DFN), which replicated a discontinuous medium within a numerical finite element model. The input signal was recorded at the slope base using triaxial geophones and incorporated into a discontinuous numerical model. The output signal was estimated through finite element analysis and subsequently compared with geophone measurements taken at the same location. Based on real-world output signals, damping parameters and the model’s natural frequency were adjusted to align both frequency spectra. Using the calibrated parameters, vibration records from various blasting projects at different distances were applied as input signals until slope failure was induced, thereby defining maximum allowable vibration limits in terms of PPV and frequency at the monitoring point. This approach provided a framework for optimizing sequence designs, charge configurations, and delay timings to enhance slope safety and prevent failure due to blasting-induced vibrations.

Jan 26, 2026

By E Emery Jr Gray

A need for more delay periods other than those normally manufactured throughout the explosives industry rarely occurs. This paper will discuss one such incident from an analytical view through practical application.

Jan 1, 1976

By Farshad Rashidi Nejad, Ali Asgari, Sanaz Norouzi

Blasting is known as the first step of rock breakage in mines. An indication of the importance of blasting is that more than 1 billion kg (2.2 billion lb) of explosives are used annually in Australia and 3 billion kg (6.6 billion lb) in the United States for rock breakage, more than 85% of which is used in the mining industry. The notion that blasting, as the first step of comminution, plays a significant role in crushing and grinding energy consumption is not an unfounded thinking. It can be noted that the comminution electrical energy consumption decreases in these ways: First, if the feed size to the primary crusher is decreased, less energy will be required to crush the ore to the same product size. Second, a decrease in work index (Wi) related to additional macro fracturing and micro fracturing within individual fragments.

Jan 1, 2015

By Yoshihiro Moriyama, Toshihiro Okitsu, Ryouichi Banno

The fracturing composition using the gas pressure generated by the thermit decomposition reaction gives the following performances.

Jan 1, 1995

By John W. Brown

"Adequate dust control in and around rock drills is a problem that must be solvedfor the health and safety of workers running the drill as well as those working around thedrilling operation This paper will discuss the designs available from most drill manufacturers todayand the effort ‘nvolved in keeping them effective on a productive basis."

Jan 1, 1999

By Ronald W. Roberts

For years, blasters have experienced near-misses, injuries, and yes, even fatalities as a result of the dangerous nature of our business. Yet, some blasters continue to portray the immortal attitude: nothing-would-or-could-ever-happened-to me syndrome. As we all know, that attitude can become disastrous to yourself or colleague(s).

Jan 1, 1996