Search Documents

By Robert C. Brown

During a research period lasting over three years, a vast number of seismograms were collected and analyzed. From this data, other than obtaining a host of new information pertaining to the effects of surface mine blast on underground mines, it was found that by mounting seismograph velocity transducers at the center of crosscuts in underground mines, seismograms can be obtained which give fairly accurate information about the maximum levels of vibration, and the associated Of stresses and strains, misfiring of blast holes, delay accuracy and delay overlap. The technique of analysis is a simple one; it involves matching of the frequency of wave or wave groups with the shot card information such as rows of holes, number of holes and the cumulative milliseconds of delays used in the blast holes. Any discrepancy that might exist between the frequency of waves and the expected cumulative millisecond delay for a given row or hole eventually will show up as a mismatch in the analysis. This simple technique enables the seismographer to be involved not only in the monitoring of blast peak vibration, but also in making recommendations as to the choice of millisecond delays, reducing the possibility of delay overlaps and reducing the hazards of blast hole cutoffs.

Jan 1, 1980

By R L. Mayville

The author explains why the strategic location and important limestone reserves at Chattanooga Quarry led to a decision to extend operating life by continued benching down to lower levels. He discusses the steps taken to accomplish this objective. These include relocation of the primary crusher from the second level to the fourth level, pre-testing of explosives designs and powder factors, control of a substantial water problem, and computer monitoring of stone production costs.

Jan 1, 1984

By Gregory B. Poole

Data collected with 16K sampling at a variety of blasting sites (construction, quarry, trench, mine) and monitoring locations was analyzed to effectively show the 16 different 1K readings all based on the microsecond that the unit went into monitoring.

Feb 1, 2020

By Wm. Reisz

There is no universal standard for Standard Operating Procedures (SOP’s). Every blasting operation has its own unique circumstances, its own methodologies and its own unique demands. It would be nearly impossible to create a one-size-fits-all document that would be totally appropriate for every blasting scenario. But there are universal objectives that should be adopted in any set of blasting SOP’s.

Jan 1, 2010

By R. F. Favreau, Patrice Favreau

"Ever since we have started to assist those responsible for blasting with blast simulation studies, we havebecome aware of an interesting aspect, namely that in 90 % of cases we are asked ‘‘Can you seek ablasting method which gives better fragmentation than the method which we use now’’. But after a visit to the site, and the evaluation of the fragmentation obtained with their present blasting method, it very often becomes evident that it is the ease of mucking and not the fragmentation which requires improvement. Hence we then proceed to do a simulation study the results of which are improved mucking rather then more fragmentation, and those responsible for the blasting always become very satisfied."

Jan 1, 2017

By Nick Lewis, Paulo Pereira

The Vulcan McCook quarry has been in operation for about 100 years. It is located about 17 miles from downtown Chicago and is surrounded by both industrial and private structures. Recent issues have forced the quarry to blast very close to structures and this will be necessary years into the future. This paper discusses the implementation of electronic detonators to McCook. It also discusses the advantages and savings that the Program has achieved

Jan 1, 2003

By Luana Ferreira de Carvalho, Aurelio Manço Garcia, Gustavo Sampaio Lopes, Jose Silvio Corsini, Davi Bastos Martins de Oliveira

The Enaex Mining Technical Solutions (EMTS) team, in partnership with the Anglo American Iron Ore Brazil drilling and blasting team, has developed a study aiming to optimize the blast design applied at the Minas-Rio project. The study consists of modeling the dynamic behavior of one lithological domain to determine the best configuration of drilling pattern, charge configuration, timing and sequencing of the blast designs applied at the mine in this particular rock. The first stage of the study was the recognition of the rock blast process in question, assessing key parameters that characterize this whole operation: geomechanical characteristics of the rock mass, implementation quality for drilling pattern and explosives charging (collar position, hole depth, explosive charge length and stemming size) and recognition of current blast designs. The central element of this study was the creation of a vibration attenuation and seed wave model which has allowed the characterization of this particular rock mass present in a region determined by the Minas-Rio team. The model is based on a near field vibration test, constituting a powerful tool in the design of blast parameters. The blast design developed from the damage model simulations basically modified the timing and sequencing. The aim of this study was to improve the fragmentation resulted by the blasting, considering the particle size requirements demanded by the primary crusher and to increase the productivity of the loading and hauling operations. The results were analyzed considering the effective productivity of the two different fleet types of shovels, where the authors have analyzed more than 46000 values of productivity from September 2017 to August 2018, taken from the Dispatch system. A significant increase in effective productivity of these load equipment was observed, 7% to the PC4000 fleet and 2% to the PC5500 fleet, values supported by statistical parameters and hypothesis tests.

By John Manka

Emulsion manufactures often spot buy the diesel fuel used in their fuel phases from various sources. Because their diesel source changes, there can be large fuel variation which may affect the quality of the resulting emulsions. This paper shows that the diesel fuel used in manufacturing emulsion explosives has a significant impact on emulsion stability and that the fuel additives dosed into the diesel fuel as it is made also have an impact on the emulsion characteristics and stability. We found that fuels with higher distillation ranges improve emulsion stability. We also found that while none of the diesel fuel additives affected the initial formation of the emulsion, some fuel additives did affect the characteristics and stability of the emulsions as measured by emulsion viscosity, droplet size, high and low shear testing, bin storage testing and freeze thaw cycling.

Jan 1, 2002

By Perry Sisk

In order to protect nearby structures during a blasting project, a peak particle velocity limit is often stipulated by a government agency or the owner of a particular structure. At the start of a blasting project, a preliminary estimate for the minimum scaled distance is often determined using a vibration prediction equation before any site-specific data have been obtained. Reasonably conservative assumptions are typically made for the unknown input variables in the vibration prediction equation until site-specific blasting data have been obtained and evaluated. Although this approach is prudent, it provides no assurance that the peak particle velocity values generated during the initial phase of the project will be below the specified limit.

Jan 1, 2013

By Jean-Francois Lagueux, Andre Pomerleau

Goldex Mine is an underground mine located near the town of Val-d’Or. Multiple innovations were required to work the mine. Due to its low grade, it was important to develop a bulk mining method to economically extract the ore. The method used is a combination between shrinkage stope and long holes stope methods. This modified method is more than adequate; however, all of the ore body must be liberated in a very short period of time. Therefore, to bring down 23.0 M tonne (25.3 M ton) of ore, large blasts up to 1.8 M tonne (2.0 M ton) are required. The situation is also complicated by the fact that the mine is located in a residential area. No less that 40 homes are built within a 1 km (0.62 mile) radius of the mine site.

Jan 1, 2011

By Frederick B. Kuhnow

Harmonic energetic delamination of T2 building is being considered for demolition at a formerly known atomic lab. The T2 building is within a containment structure that is under a negative pressure of -49 Pa (-0.2 inches of WC) so that no remaining radioactive material is leaked out. The T2 containment enclosure is a portal frame-type system that spans east/west over 35.05 m (114’-11 7/8”) and spaced 2.9 m (9’-6”) apart. The west side of the portal frames is supported by a 64 cm (2’-1”)thick concrete wall which is backfilled to the west and open to the T2 basement to the east. The east side of the portal frames is supported by a 61 cm (2’-0”) thick concrete wall that is backfilled to the east and open to the tank farm vaults to the west. A concrete slab-type footing supports both the east and west walls. Transverse walls provide lateral support for the walls as part of the original design. The west wall has an elevated slab that provides further stiffening of the concrete wall between the transverse walls.

Jan 1, 2017

By Ken Schei, Martin Reed, Samuel Bowser, John Wright

From October 18 through October 21, 2001, United States Antarctic Program blasters opened ten access holes for research divers in 11-ft. thick sea ice at Explorers Cove, McMurdo Sound, Antarctica. During this project, a blasting seismograph with a hydrophone accessory was used to monitor the underwater shock waves associated with the blasting technique. Shock wave values averaged 42.3 psi for initial (cratering) shots and 5.9 for subsequent clearing shots, indicating that the ice absorbs most of the shock wave. The results also provide data for refining safety protocols for divers and for the protection of marine biota.

Jan 1, 2003

By Mick Lownds, Ruilin Yang

The potential advantages of electronic detonators with accurate timing have been increasingly recognized by the blasting community. However, in comparative blasts the results with pyrotechnic timing are sometimes comparable to those from electronic timing. Statistical variation in blast results is a plausible cause of these observations.

Jan 1, 2011

By Joshua Hoffman, William Chad Wedding, Braden Lusk

The emergence of electronic detonators as viable products for use in production mine blasting has enabled mining professionals to rethink the traditional blast design methodologies that pertain to timing. In many ways, electronic detonators can allow great advances in productivity, cost effectiveness, fragmentation, and safety. There are a number of commercially available systems that enable users to program delay times, usually in one-millisecond intervals, according to design decisions. While manufacturers have performed internal studies pertaining to the accuracy of these systems, an independent study quantifying the accuracy of the systems has not been completed to date. The mining industry is in the business of production and any quality control endeavors to independently confirm the accuracy studies performed by the manufacturers would only detract from their bottom lines. Furthermore, limited information is available concerning the accuracy of modern pyrotechnic delay based detonators. In 1985, the Bureau of mines completed a study of three manufacturers’ electric millisecond delay detonators (Bajpayee, 1985). This was the most recent extensive independent study performed on detonators, which unitized pyrotechnic delays, from numerous manufacturers. Advances in the manufacturing process for pyrotechnic delays may have increased the accuracy of detonators using these technologies in recent years. It is commonly accepted that electronic detonators are more accurate than both shock tube type non-electric as well as electric detonators, but the relative accuracy was not objectively and adequately quantified.

Jan 1, 2011

By Luana Ferreira de Carvalho, Aurelio Manço Garcia, Gustavo Sampaio Lopes, Jose Silvio Corsini, Davi Bastos Martins de Oliveira

The Enaex Mining Technical Solutions (EMTS) team, in partnership with the Anglo American Iron Ore Brazil drilling and blasting team, has developed a study aiming to optimize the blast design applied at the Minas-Rio project. The study consists of modeling the dynamic behavior of one lithological domain to determine the best configuration of drilling pattern, charge configuration, timing and sequencing of the blast designs applied at the mine in this particular rock.

Feb 1, 2020

By Luke Thornton, Jack Janssen

An unconventional drill pattern is used in an aggregate quarry to reduce pioneering costs. The site is the Iron Mountain Quarry, Granite Falls, WA., an aggregate quarry with an annual production of in excess of 1,000,000 tons. The problem is to pioneer a forty acre addition of on top of Iron Mountain. The entire area had a vertical relief of fifty to one hundred feet with no level surfaces. How does one achieve the minimum cost?

Jan 1, 1997

By H Leonard Mangum, Victor C. Bryan, Dan McCutchen

Recently there has been an unprecedented marketing effort to promote the advantages of various non-electric initiation systems. This activity has probably been influenced by a major manufacturer's decision to discontinue electric detonator production. Subsequently, distributors of explosive materials, rather than introducing new electric detonator brands, are emphasizing the use of existing non-electric systems. In many cases, such methods fill the need of explosive users in the quarry industry. However, the use of any initiation system should be based on performance, rather than the bent of the market or convenience to the supplier. This analysis is an evaluation of the performance of non-electric systems with emphasis on double trunk line and loop (redundant), as compared to precise electric detonators in use by Martin Marietta. Redundant non-electric detonators, even though more costly, offer the most reliable method of non-electric initiation. However, state-of-the-art precise electric detonators give the best overall performance, except in an environment involving extraneous electricity.

Jan 1, 1990

By César Ugaz Castañeda, Paulo Fernández Alvarado, Richard Sotomayor Oblitas, Rocke Enríquez

Mina El toro has been making substantial changes in its operation to improve its social impact and productivity. Because of the use of gasified emulsions and electronic initiation system, it was possible to mitigate vibrations and carry out massive blasting, increasing its production by 4.2% and minimizing complaints from communities.

Feb 1, 2020

By Denise de La Corte Bacci

The Brazilian Regulation NBR 9653 is a guide intended to evaluate mine and quarry blasting effects in urban areas. The first version, written in 1986 by the Committee of the Brazilian Associate of Technical Norms, is currently being revised. Current regulations specify a maximum PPV limit of 15 mm/s (0.59 in/s) without consideration of frequency or type of structures being protected. The present regulation is still a draft and it is not validated. Several different agencies and institutions have participated in the Committee such as the Environmental Agency from the State of São Paulo (CETESB), University of São Paulo (POLI-USP), University of Rio Grande do Sul (UFRGS), National Department of Mineral Resources (DNPM), Aggregate Industry (ANEPAC and SINDIPEDRAS), besides a number of industry representatives, explosives manufactures and independent consultants. The present regulation proposes to modify the limits of particle velocity and introduces new definitions and criteria for evaluation of vibrations, as well recommendations to address blast vibration complaints.

Jan 1, 2005

By Luis Huaroc, Augusto Sotomayor, Erick Rodriguez, Paulo Fernández, José Ricaldi, Luis Alejandro

The application of the Kuz-Ram model for the prediction of fragmentation is used worldwide, in Coimolache Mine it was used to determine blast domains and optimize the process by obtaining drilling patterns that meet a required X80 and reducing the uncertainty of drilling.

Feb 1, 2020