Search Documents

By Bruce Vandenberg

Two tests were set up as part of the course given by Blasting Analysis International. Both tests were performed using the prototype Velocity of Detonation Recorder (VODR). The prototype has several limitations, which have been rectified for the production units.

Jan 1, 1990

By A. Ravi Kumar

A trench is a structure to accommodate fluid carrying pipelines for water, gas, petroleum products etc. Trench serves the purpose to haul the fluids in bulk over long distances safely and economically. Use of pipeline for moving oil and gas was essentially a post World War II development, but now it has acquired its own importance.

Jan 1, 2008

By Fumihiko Sumiya, Shinya Tanaka, Yukio Kato, Kenji Tanaka, Tetsuya Sawada

When explosives are heated under an acidic environment due to metal sulfide and sulfuric acidity, their decomposition temperature falls remarkably and decomposition reaction occurs quickly, and then explosives have the risk of the deflagration to the detonation transition. Heat resistant commercial explosives which can be used under conditions of high temperature of 200ºC and an acidic environment were studied. We developed the explosive composition consisted of ammonium perchlorate (AP) as oxidizer, saturated hydrocarbon oil as fuel and binder, and calcium carbonate as decomposition inhibitor. The characteristics of this explosive composition show a heat resistance over 24 hours at 200ºC, and a detonation velocity over 2,500 m s-1. This explosive composition has a cap-sensitivity at temperature higher than 100ºC. Cost effective heat resistant commercial explosives were created by the optimization of the grain size of AP as a main component, the addition of saturated hydrocarbon oil and calcium carbonate, and the control of bulk density by the addition of micro-balloons.

Jan 1, 2003

By P McConnell, T Garrigan

Tara Mines Limited, in Ireland, is Western Europe's largest zinc mine. Annual metal production, from 2.5 million tonnes of ore, consists of 180,000 tonnes of zinc and 34,000 tonnes of lead.

Jan 1, 1989

By Rachel Bauer, Jacob Henderson, Dr. Catherine Johnson

Capital Quarries in Owensville, Missouri faces several challenges when designing a blast that allows for ease of movement while maintaining controlled throw and compliant air over pressure. The primary challenge is the nearest non-owned structure (NNOS) is a residential home located 250 feet from the quarry. Another challenge is a production bench which is 100 feet tall and separated from the NNOS by Pennsylvanian fire clay that filters out high frequency waves from the blast. Material from the blast must also be less than 5 inches in order to be processed by the crusher in the quarry. To provide as much relief as possible, production shots will consist of a single row with the minimum required burden. To design the shot, signature hole analysis was used to determine the optimal timing between powder columns. Electronic detonators provided an accurately timed shot to minimize the amplitude of the vibrations while maximizing the frequencies. Boretraking and 3D profiling with Renishaw laser profiler and Strayos drone photogrammetry provided an accurate burden measurement. Powder factor was kept at 1.3 tons/lb using bulk emulsion. The boreholes were split into 5 powder columns with the top of the hole firing first in order to blast to floor grade. The resulting shot produced good fragmentation and shot to floor grade. Seismograph readings showed air over pressure vibrations within legal limits. Due to this success, multiple shots will be designed using the process described.

Feb 6, 2023

By Michael Olmsted

Inspection of boreholes prior to blasting can result in cost reductions as well as increases in efficiency and safety. Until recently, borehole inspection was performed in two manners. For simple inspections, a flashlight was used to view the upper part of the hole. More thorough inspections were performed with long tool strings developed for oil field applications. Borehole inspection tools developed specifically for mining and blasting applications have now been developed. Video Cameras developed for borehole inspection have been in service for several years. Now measurement tools are available, developed specifically for mining.

Jan 1, 2000

By Lifent Li, Jhon Silva-Castro

Since millisecond-delay detonators were first introduced, at least two variables, among others, have been more closely considered when timing a mining blast: the accuracy and the precision of the initiation system. Currently, most mine blast design software has the capability to use the precision/accuracy of the firing system and display the overlap timing window between charges in any given time interval (8 ms, 3 ms, etc.). Despite these technological advances, there are still situations which result in the overlapping of charge timings. The consequences of overlapping charges involve flyrock events, fragmentation and diggability problems, and other inconvenient situations affecting the operation of the mine.

Jan 1, 2015

By Des Bolton

With the introduction of Cast Blasting techniques, field controls of Drilling & Blasting operations became more important. New drills were purchased which were equipped with sophisticated instrumentation and more accurate drilling plans were required. Concurrently a decision had to be made on the replacement of borehole logging equipment owned by the mine. The use of a contractor to log blast boreholes was eventually decided upon, the information gained from this operation is used in the short-term drill and blast planning and may also be used to assist in the coaling operation if density I quality correlations prove acceptable.

Jan 1, 1994

By Dennis L. Paisley, Thomas P. Turner

Laser slapper detonators are the next generation detonator under development at the Detonations Systems Group at Los Alamos National Laboratory and function very similarly to an electrical slapper. A fiber optic transmits a laser pulse to ablate a thin metal film. This film, or flyer as it is commonly called, is launched through a short barrel to km/s speeds. The flyer shock loads or slaps a high density pressing of secondary explosive, setting off a detonation therein. Laser slapper detonators afford a number of safety advantages over other conventional detonators. Most important they require very high peak laser powers to operate, orders of magnitude larger than possible sources of natural or man-made accidental stimulus. Because light is transported over fiber optics, laser slappers avoid many of the electrical hazards associated with detonators. Use of insensitive, secondary explosives makes these detonators safer to handle, manufacture, transport, and deploy.

Jan 1, 1994

By Jeffrey Meissner, Charles Dowding

Cracking is one of the concerns cited by owners of structures adjacent to construction or mine blasting. During the past decade a large number of measurements have documented the low level of crack response produced by typical, ground motions compared to those produced by climatological effects. These data support the observation that there is a level below which ground motions do not cause even cosmetic cracking. As with all new findings, these crack response measurements need to be thoroughly investigated for all possible alternative interpretations. Among these alternatives is that uncracked locations are more affected than cracked locations. This paper presents measurements to shed light on the influence of existing cracks and the response of uncracked, but weak locations. Blast and weather induced responses of cracked and uncracked areas of gypsum wall board are compared in two structures: one near a surface coal mine in Indiana, the other near a limestone quarry in Florida. The ground motions that excited one of the structures were unusual in that the dominant excitation frequencies of 5 Hz were near the structure’s natural frequency and amplitudes exceeded 0.7 ips (18mm/s).

Jan 1, 2011

By Ron Beeslaar, Tony Rorke

The Professional Blast Manager is a blast design tool that has been developed in South Africa. It is aimed at mining and civil engineen, blasting contractors and mine planning engineers. The code can be used as a stand-alone package or be combined Into complex mine information systems.

Jan 1, 1998

By Narendra Gupta, Gaurav Srivastava, Abhinav Sharma

From the days when plain detonators and safety fuse were used for initiation of commercial explosives, the commercial blasting and mining industries have made rapid strides. With the advent of electronic detonators in the late ‘90s, the face of commercial blasting was changed forever. The Mining Industry in India initially took a while to embrace Electronic Blasting Systems (EBS), however, more recently the industry has taken to EBS in a big way.

Jan 1, 2015

By James A. McGrath

"The predominant key word associated with all commercial blasting methods is “safety”. Safetyshould take precedent over all other aspects of the entire explosives industry which on a wholehas had an excellent track record as to number of injuries per unit of hours worked at all blastsites throughout our country."

Jan 1, 1999

By W. J. Birch, A. Wetherelt

The scaled-distance model for blast vibration analysis is the standard method employed throughout the surface mining and quarrying industries to model Peak Particle Velocity (PPV) data. Although empirical, the method is widely accepted and through the simplicity of its application and ease of graphical verification is set to remain a popular option. The validity of the technique relies principally on the fundamental parametric assumption that blasting data is normally distributed. Throughout the evolution of scaled-distance modelling, this is an issue that has most often been presumed rather than proven (most likely due to the tediousness of the calculations involved). In the few cases when normality has been given some degree of consideration, the result has been the product of a simple visual inspection of frequency distributions: clearly unsatisfactory. However recently the soundness of this assumption has been brought into question, with obvious connotations for blast modelling in general. This paper considers this fundamental issue and seeks to investigate the normality hypothesis within the blasting context through an in-depth statistical analysis of what possibly can be described as an ‘ideal’ blasting dataset. This being a rare case study concerning an opencast coal site in England, where for the entire life of the site every single blast was monitored and recorded through the use of permanent monitoring stations. This has provided a unique ‘total population’ dataset of considerable size from which the assumptions of normality are put to the test.

Jan 1, 2005

By Langdon T. Mitchell, Karl Ingmarsson

The title is not referring to jewelry; nor is it about diamond core drilling. This article is instead about an emerging application for diamonds, hard rock percussive drilling with diamond drill bits. Diamond’s outstanding wear resistance has long been taken advantage of in core drilling. However, until now diamond has been less successful in hard rock production drilling in the mining and quarry industry.

Jan 1, 1999

By Michael D. McGill

The effect of fragmentation size distribution as it relates to front end loader productivity was evaluated by comparing loader cycle times to fragmentation size of the shot rock. At Gold Mine in Southern Utah, a gold deposit containing both limestone and sandstone formations were blasted in the same shot.

Jan 1, 1994

By Norman Paley, Zachary Pickett

The Red Dog Mine is a high-grade zinc-lead mine located in northwest Alaska which began operations in November 1989. In June 2014 the upper half of a charge in a trim shot in the Aqqaluk pit deflagrated. No other holes in the area were observed to react and the remainder of the pattern was shot without incident. This was the only known case of a deflagration in the 25 years of operations. As part of the investigation into the cause of this incident rock samples were obtained from the area of this hole and from other areas in this pit.

Feb 1, 2020

By David Harrison, Edward J. Walter, Meitra Ferek

Agreat tool in the prevention of blasting complaints and subsequent damage claims. In today’s highly competitive industry, we are always looking for ways to become more cost effective. This article investigates the importance of pre-blast surveys-not just for regulatory compliance, but as an overall long term cost cutting and public relations tool.

Jan 1, 1995

By Frederick Kuhnow

In open pit blasting, energy is released and transmitted through the geology. Negative effects can impact operations and can affect mine production. This paper presents recommendations for blast design to prevent damage due to ground motion from blasting on adjacent concrete structures of underground operations. It includes a case study describing a problem regarding an open pit mine expansion and asks whether production blasting will damage concrete shaft structures due to blast stress waves and blast-induced ground motion.

Jan 1, 2014

By Qian (Ken) Liu, Remi Proulx

A large scale blast damage project was carried out over the past two years at INCO Ltd Manitoba Division co-funded by the Canada/Manitoba Mineral Development Agreement. The experiment was conducted at the T-3 Mine in two mining stopes with an experimental drift developed in the hanging-wall for the installation of monitoring instrumentation. The objective was to observe and subsequently to reduce ore dilution by monitoring the performance of blasts, the hanging wall movement, as well as the cavity of the open stopes.

Jan 1, 1995